o t')C.. 8-M24 GALV. H.D. BOLTS. ON 370 P.C.D. WITH NUTS. /. AND LEVELLING NUTS. COG 100. SL82 FABRIC. TOP AND BOTTOM. E
Grade 7 Stone Base. Natural 84 with Tan Thatch Zone. 1" to 2" Foam. "Perfect
Play" Playground Detail. 3"-4" Lightly Compacted over Stone Base for Toddler ...
LN. _> l+ .200 [5.08] 80. MIN. __1.210 [30.73] MIN. _>. MOUNTING PAD LAYOUT
. 1). _> = TYP-. TYP. \ E005 [E015] f \m .093 [2.36] ...
a: 950m 5.; ._m: 5.52 - 880w 62: MOFIU-JDDOE. (variable length). \ Minilux HRL
Extrusion. 8. 1 x. O r p p. A d. u e. 5 m n e w. m. W m. A e v. R 8. n n .m .w m.
TOP HAT aluminium powder coat finish. 2.7m Centre Support Square Umbrella. Centre Support - Model SUA-CS27. 1:100 at A4.
Itinyi Pumping Station - Marungu Tank: Plan & Profile km 0+000 to 1+300. WMCL-KRC-RM 02-01. 7. WMCL-KRC-GM 02-01. WM
Services Building Department Bldg & Fire Safety Dept. ... 4701 W Russell Rd 401 California Avenue 240 Water St. 731
BASE PLATE 200x200x12 pl. with Ã50 service hole. 4-M12 hold down bolts at 140mm c/crs. Grade 4.6/s galvanised or stainl
We call it consistency. A crisis of knowledge? Gaining bigger knowledge from ... He would rather immediately begin to create ..... take this iPhone as an example.
Dec 1, 2016 - WMCL-KRC-IPS-01. WMCL-KRC-IPS-03 ... Tel:(254) -020 3876690/1/2 .... 30(1:1:2) WITH MINIMUM CUBE STRENGTH
Academy for Media Arts Cologne and the Berlin University of the Arts. Bernhard Krusche .... comprehensive sense-making of the entire enterprise: The Design inspired enterprise. ... ing more trust and more time. Any self-respecting systemic ...
4-M12 H.D. bolts to be threaded rod grade 4.6/s hot dipped galvanised, or stainless steel Gr.316. Supplied with nuts, wa
See car specific diagrams for further information. 4. Install into the ... NOTE: Car
manufacturers can change wiring specifications without notice. Ensure that.
Oct 10, 2010 ... Jailbreak, to get Cydia in IPT. • jailbreakme.com (via wifi) or. • spirit.exe only for
iOS 3.1.3 or below (via usb cable). 2. Add sources in Cydia.
(A) Slide braid clamp over Being certain that clamp seats ... 6 K 3. (A) Seatcenter
contact firmly againstcabiedielectricandsoft solder to cable conductor.
6m Square Corner Supporrt Model: SUA-PS60L (Linear Edge). I Permissible Design Wind Speed W33 (33m/sec) I. Australian St
Powder coated arch bar aluminium RHS. The infill is supplied as a unit. Consisting of: - Infill panel, riveted to the ar
Link plate, each side, bolted to umbrella arms.
Arch bar bolted to link plates.
A
B
B
C
C
Infill panel riveted to arch bar
A
'Frog', with eylets for shock cord, welded to membrane.
General Arrangement Plan
Linked Infill Installation With the umbrellas installed and opened: 1. Remove 2nd nuts and washers from the underside of the appropriate arms that have extended bolts. 2. Fit the link plates to the bolts on the underside of the arms and tighten the nuts. Use the slotted holes for adjustment. 3. On one side, tie off the shock cord to the arm near the first eyelet and thread the shock cord from eyelet to eyelet between the 'frog' and the infill panel. Do not pull the lacing tight. (Thread the cord into the front side of the eyelet. i.e. from the bottom, up and out the top then over to the bottom and up, and so on.) 4. Repeat step 3 for the other side. 5. Tighten the lacing ensuring that the arch bar stays central between the membrane edges (Refer Section B-B). Tie off the cords to the arms. 6. Check that the nuts are secure and tight, and that the tension on the infill panel from the shock cord is even both across and along the panel.
eq.
Infill panel, riveted to arch bar
eq. Umbrella arms
Arch bar
Shock cord threaded through 10mm eyelets in infill panel.
Powder coated arch bar aluminium RHS
The infill is supplied as a unit. Consisting of: - Infill panel, riveted to the arch bar, with shock cord attached. - Aluminium arch bar with tensioning cable and bolted on link plates.
Section A-A
Structure membrane
'Frog' welded to umbrella membrane, with 10mm eyelets for shock cord.
