2014 CHEVROLET MUNICIPAL VEHICLES TECHNICAL MANUAL

90 downloads 12400 Views 9MB Size Report
equipment or components supplied to Chevrolet or its dealers by independent suppliers. .... Chevrolet MyLink6 touch screen color display featuring AM/. FM radio and CD ..... SUSPENSION. 4-wheel ..... NOTE: For wiring diagram see page 17.
GM Fleet and Commercial Specialty Vehicles • 100 Renaissance Center, 20th Floor • Detroit, MI 48265-1000

2014 CHEVROLET MUNICIPAL VEHICLES TECHNICAL MANUAL

For Information 1-800-FLEET-OP (353-3867) www.gmfleet.com

2014 CHEVROLET MUNICIPAL VEHICLES TECHNICAL MANUAL

Caprice 9C1

I m pa l a 9 C 1

I m pa l a 9 C 3

Tahoe PPV

Tahoe Special Service

E x p r e ss V a n

Suburban

S i lv e r a d o

About This Publication

NOTES

•C  are must be taken during customer installation of equipment and wiring to ensure that all holes drilled in the body are corrosion protected, properly sealed and that vehicle wiring harnesses, piping or other components have not been displaced or damaged. Aftermarket equipment installers must be mindful of applicable Federal Motor Vehicle Safety Standards. This information can be obtained directly from the National Highway Traffic Safety Administration. • T hese vehicles are equipped with an air bag system. The air bag system in your police vehicle includes front seat back, front knee and side curtain air bags. Customer installed equipment such as security barriers behind the front seats should not be mounted so that the barrier ends are within the side air bag deployment zones. The sensors and other components for the air bag system must not be relocated to accommodate the installation of customer furnished equipment; please refer to the service manual for sensor and other component locations. For information concerning instrument panel top pad mounted equipment and air bag system deployment zones, see the air bag information section in this catalog. • T his catalog is not updated during the model year and should not be used for ordering purposes. It is intended as a source of basic information. All illustrations and specifications in this literature are based on the latest product information available at the time of publication. General Motors reserves the right to make changes at any time without notice. For further details, consult your local dealer. •A  note about vehicle alterations by independent suppliers: This catalog shows pictures of vehicles that have been altered or upfitted with equipment or components supplied to Chevrolet or its dealers by independent suppliers. Chevrolet is not responsible for the safety or quality of design features, materials or workmanship of any alterations by a supplier.

2014 Chevrolet Municipal Vehicles Technical Manual

2014 Chevrolet Municipal Vehicles Technical Manual

Index

Law Enforcement Product Council District Sales Managers And Fleet Service Managers Caprice Police Patrol Car (Option 9c1) Impala Limited Police Patrol Car (Option 9c1) Impala Limited Undercover Car (Option 9c3) Tahoe Police Patrol Suv (Option Ppv) Tahoe Special Service Suv (Option 5w4) Express Transport Van (Option 1LS & 2LS) Suburban Commercial Fleet Suv (Option 1fl) SILVERADO 1500 CREW CAB Pickup work TRUCK 1WT

2014 Chevrolet Municipal Vehicles Technical Manual

Law Enforcement Product Council

Mission Statement

To pledge an integrated partnership between General Motors and Law Enforcement. Together, we will identify, evaluate and promote enhancements to products and relationships that address the vehicle requirements of the Law Enforcement Community.

Law Enforcement Product Council| 3

John Woronczuk Royal Canadian Mounted Police [email protected] 613-843-3775

Oliver Harris Tulsa Police Department [email protected] 918-669-6020

Jerry Newbury Texas Department of Public Safety [email protected] 512-424-2043

Ed Sanow Law and Order Magazine [email protected] 800-843-9764 Ext. 28

John Dillon Federal Bureau of Investigation [email protected] 202-324-4925 Gregory Dimesa New York City Police Department [email protected] 718-476-7537

Lloyd Dow York Regional Police [email protected] 905-830-0303 Ext. 7380

Kyle Shelton Colorado State Patrol [email protected] 303-273-1660

Rich Lee San Francisco Police Dept. [email protected] 415-553-1221 Tammee Turcott Phoenix Police [email protected] 602-261-8393

Ron Gromak Michigan State Police [email protected] 517-322-5598

Dave Winter Durham Regional Police Service [email protected] 905-579-1520 ext 4739

David Lindon City of Hoover [email protected] 205-739-7187

Jon Gaddis Portland Police Bureau [email protected] 503-823-4730

LEPC members are available to all of law enforcement for questions, comments, or ideas you wish to convey to General Motors.

2014 Chevrolet Municipal Vehicles Technical Manual

Regional Government Sales Representatives

Sales and Service

Fleet and Commercial Operations Sales Support Manager/ police vehilce specialist

North CENTRAL Region

Northeast Region

Government Fleet Account Executive

Jay Ferraro

Dan Centinello

PHONE: 914-391-5493 [email protected] Connecticut Delaware District of Columbia Maine Maryland

PHONE: 716 553 3296 [email protected] Massachusetts New Hampshire New Jersey New York

Todd Little

PHONE: 313-300-0528 [email protected] Illinois Indiana Iowa

PHONE: 810-441-2781 [email protected] Michigan Minnesota North Dakota

WESTERN Region South Central Region

Rich H. Patterson Idaho Montana Nevada New Mexico

Sales Support Manager/ police vehilce specialist

Government Fleet Account Executive

Rick Maybury

Bill Hajduk

PHONE: 817-909-6457 [email protected] Arkansas Kansas Louisiana

PHONE: 214-616-8166 [email protected] Mississippi Missouri Nebraska

James Mellon

Oklahoma Texas

Sales Support Manager/ police vehilce specialist

Billy Regar

PHONE: 407-375-4801 [email protected] Alabama Florida Georgia Kentucky

Oregon Utah Washington Wyoming

PHONE: 386-295-5637 [email protected] North Caroline Puerto Rico South Carolina

Tennessee US Virgin Island West Virginia

Rich Moore

PHONE: 630-531-1663 [email protected] Area: IL, WI, MN, IA, ND, SD

Bob Briedis

PHONE: 313-268-2160 [email protected] Area: MI, OH, IN

Fleet Service Managers

PHONE: 602-885-2229 [email protected] Area: AZ, CO, NM, HI, Southern CA, Southern NV

MARK Romans

PHONE: 916-517-2418 [email protected] Area: UT, WA, OR, ID, MT, AK, WY, Northern CA Northern NV

Fleet Service Managers

Jerry Bartz

PHONE: 228-396-1390 [email protected] Area: AR, OK, MS, LA, Southern TX

Mike HURRELL

PHONE: 214-604-9247 [email protected] Area: MO, KS, NB, NE, Northern TX, Eastern NM

Fleet Service Managers

Dana Brodbeck

PHONE: 239-272-5752 [email protected] Area: FL, SC, NC, PR, VI, Southern GA

Government Fleet Account Executive

Canada

Bob Stipek

PHONE: 248-320-8615 [email protected] Area: MD, DE, PA, VA, DC, Western NY

Fleet Service Managers

Scott Bruske

PHONE: 602-228-1286 [email protected]

Government Fleet Account Executive

SouthEAST Region

Ohio South Dakota Wisconsin

Sales Support Manager/ police vehilce specialist

Government Fleet Account Executive

Alaska Arizona California Colorado Hawaii

Jay Lewis

PHONE: 516-458-7994 [email protected] Area: NH, VT, MA, RI, CT, NJ, ME, Philadelphia, Eastern NY

Sales Support Manager/ police vehilce specialist

Government Fleet Account Executive

Andrew Reyntjes

Pennsylvania Rhode Island Vermont Virgina

Fleet Service ManagerS

Will Bachewich

PHONE: 905-644-1051 [email protected] AREA: Canada

For Additional Assistance Phone: 1-800-FLEET-OP (353-3867) or www.gmfleet.com

Mark Monismith

PHONE: 248-672-9179 [email protected] Area: AL, TN, KY, WZ, Atlanta, Northern GA

|5

6 | NOTES

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 | 1

Shown with aftermarket equipment

Shown with aftermarket equipment

Updates for 2014

New Features

DELETIONS

• All-new column-mounted shifter for increased room, comfort, and convenience • Standard center console steel mounting platform for attaching equipment more easily (see page 12 for details) • All-new instrument panel and gauge cluster with 8-inch Chevrolet MyLink6 touch screen color display featuring AM/ FM radio and CD player • Bluetooth7 streaming audio and cell phone connectivity, voice recognition, and music navigator (Applications requiring a USB12 connection are not compatible) • Surveillance Mode with integrated circuit for connection to customer-supplied switch • Ultra high-strength steel added to both A-pillars for significant improvements in roof crush safety • Revised front seats with increased comfort and support while wearing a utility belt (front hip room increased to 57.5 in. from 56.7 in.) • Extended safety belt receivers for easier buckling • Driver and front passenger 6-way power seat adjusters • Trunk release button now on both front door interior panels • Standard Electric Power Steering for efficient cornering and stability • Thicker front struts (32mm from 30mm) for handling and tuning, with increased front stabilizer bar (26mm from 24mm) • Increased ground clearance (6.0 in. from 5.6 in.) • Folding blade key FOB replaces solid shaft, with standard Remote Keyless Entry and remote vehicle start • New exterior color: Mystic Green (GZ7) • Inside rearview manual day/night mirror (without compass) • Battery, Auxiliary • Fleet key

• Detective Package (Option 9C3), front center console with armrest and 2 auxiliary outlets • Floor-mounted shift lever • Inside rearview mirror with compass • Driver 8-way power seat adjuster • Front passenger 8-way power seat adjuster (Option A6F) • Battery, auxiliary 600 CCA, 70 AMP (Option K4S) • Power rack-and-pinion steering • Overhead sunglass storge compartment • Power Steering oil cooler • Inoperative dome lamp (Option 7Y6) • Alto Grey Metallic (GGG) • Content Theft Alarm

CHANGES • Jet Black interior code changed from (4BB) to (4AA) • Front bucket cloth seat with cloth rear bench seat code changed from (ADX) to (H1T) • Front bucket cloth seat with vinyl rear bench seat code changed from (ACC) to HCQ) • Driver Information Center programming controls moved from steering wheel to turn signal lever on left side of steering column • MyLink 8-inch touch screen display houses features for vehicle customization • Front door lock buttons relocated to the top rear of door trim pad as a dedicated post (pull handle once to unlock, pull again to open door) • Fleet key (options 6E3 and 6E4) will not be compatible with previous years

6. MyLink functionality varies by model. Full functionality requires compatible Bluetooth, smartphone and USB connectivity for some devices. MyLink on Spark and Sonic does not include functionality such as enhanced voice recognition, Gracenote and CD player. 7. The Bluetooth word mark is a registered trademark owned by Bluetooth SIG,Inc. and any use of such mark by GM is under license. Go to gm.com/Bluetooth to find out which Bluetooth phones are compatible with the vehicle. 12. Not compatible with all devices.

2014 Chevrolet Municipal Vehicles Technical Manual

2 | CAPRICE

Police Package 9C1

This vehicle has been designed for police work up to and including high speed emergency vehicle operations. GM restricts the sale of police vehicles and they are not to be sold to retail customers.

MODEL AVAILABILITY 1EW19 - 9C1

Rear-wheel drive

STANDARD EQUIPMENT SUMMARY Warranty 3 years / 36,000 mile bumper-to-bumper limited warranty (whichever comes first, see dealer for details) 5 years / 100,000 mile powertrain limited warranty (whichever comes first, see dealer for details)

INTERIOR FEATURES Air conditioning Dual-zone automatic climate control with pollen air filtration Bluetooth Bluetooth for phone and music, personal cell phone connectivity to vehicle audio system, voice recognition, music, navigator and streaming audio Bottle holder Bottle holder in the front doors Capture Speed Feature Capture (stores) certified vehicle speed in digital speedometer via steering wheel controls when following another vehicle COMPASS Not available Cruise control Electronic with set and resume speed Dome Lamps Front and rear dome lamps (excludes map lamps) The front dome lamp has switches for ON/OFF and OFF to disable automatic lamp function. (see page 13) Driver Information Center Monochromatic display with customization features Floor covering Carpeted front and rear carpeted floor mats are available; see Option b34. Option 6a3 heavy-duty vinyl floor covering available, requires HCQ vinyl rear seat (see page 6) Glass Solar-Ray light-tinted, windshield, driver and front passenger, light-tinted rear backglass GlOVE BOX Non-locking door with light Mounting platform Center front customer console mounting platform located in 10 inch space between front seats (see page 12 for description) Mirror, Inside rearview Manual day-night (without compass) NAVIGATION SYSTEM Not available Onstar Not available Outside Temp. Display Standard; displayed at top of radio screen Radio Chevrolet MyLink6 radio, AM/FM stereo with CD player and MP3 Playback, includes 8" diagonal color touch screen display, Bluetooth7 for phone and music, personal cell phone connectivity to vehicle audio system, voice recognition, music navigator, streaming audio and outside Temperature Display. Radio audio is provided by front door speakers and two pillar-mounted tweeters. Rear speakers are not available. Lighting, power door locks, remote functions, and other features can be customized using the radio touch screen. Restraint system Safety belts, driver and front passenger with pretensioners, dual stage frontal air bags1 and a passenger sensing system with passenger frontal air bag ON/OFF indicator. Driver and front passenger head side curtain air bags1, knee air bags and front seat back mounted pelvic-thorax air bags. A Rollover Sensing System senses an impending rollover and deploys the head side curtain air bags1 and safety belt pretensioners in the event. The head side curtain air bags1 are designed to remain inflated for a longer period than the frontal, knee and pelvic-thorax air bags1 to reduce the likelihood of occupant head and torso excursion outside the passenger compartment if a rollover should occur. (Combined front and rear seat row head side curtain air bags1 are available; see option AYG on page 6) NOTE: Safety belt extenders are available in 9 inch (part number 89027366) and 15 inch (part number 89027367) through your dealer at no charge Seat, front Cloth bucket seats with heavy duty foam, sculpted for gun belts; high-wear fabric bolsters and seat back security panel. Driver and passenger 4-way power with lumbar and manual recline, manual fore-aft movement. 10 inches of space between front seats; an equipment mounting platform is located between front seats. Seat, rear Cloth bench, non-folding seat back (vinyl rear seat available; see option HCQ on page 6, requires 6a3 heavy-duty vinyl floor covering) Shift Lever Column shift lever Smoker's package Not available Speedometer/cluster 160 mph certified analog display with 1 mph increments. Driver Information Center (DIC) has different displays which are accessed using the control buttons on the turn signal lever at the left side of the steering wheel. The DIC displays speed, trip, vehicle information and warning messages (see page 9) Surveillance mode Circuit is terminated in the 16 cavity upfitting connector for connection to customer switching to ground; all automatic interior and exterior lighting is extinguished and radio is blacked out. All manual lighting control remains functional. (see description on page 19) Steering wheel Tilt and telescoping with cruise and audio controls Theft deterrent System pass-key® iii+ (Content Theft Deterrent is not an orderable option). See your dealer for additional information. Visor Driver and passenger with covered mirrors, not illuminated Warning lights Brake, safety belt, air bag, anti-lock, check engine, Sport Mode, StabiliTrak, high beam and cruise control Warning TONES Key-in-ignition, driver door open and safety belt reminder chime Window OPERATION Power front and rear, Express-Down (front only) with rear window lockout (controls located on front door panels)

1. Head curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. 6. MyLink functionality varies by model. Full functionality requires compatible Bluetooth, smartphone and USB connectivity for some devices. MyLink on Spark and Sonic does not include functionality such as enhanced voice recognition, Gracenote and CD player. 7. The Bluetooth word mark is a registered trademark owned by Bluetooth SIG,Inc. and any use of such mark by GM is under license. Go to gm.com/Bluetooth to find out which Bluetooth phones are compatible with the vehicle.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 | 3 electrical features Auxiliary power, front

 iring provision for total of 110 amp auxiliary power at right front corner of the center floor mounting plate. Three connectors W provide 50 amp battery power and ground, two 30 amp relay controlled battery circuits and signal circuits for ignition control (HOT in START/RUN, and ACCESSORY/RUN), vehicle radio mute, vehicle speed signal, park-enable and a customer switched surveillance circuit. (See page 13). CAPTURED SPEED This standard feature allows the officer to capture the speed of the Caprice while pacing another vehicle. (see page 12) Auxiliary power, trunk Two auxiliary battery power connection studs in trunk provide a total of 120 amps (See page 13) Ground stud Auxiliary, located in trunk (see page 13) LOCK-OUT PROTECTION Feature is programmable ON or OFF via the vehicle radio customization menu. The factory default is Lock-Out Protection OFF. Remote keyless entry will not function when vehicle is locked with key in the ignition, under this condition a spare key is required to operate door lock cylinder for entry. Power outlet One located on instrument panel (12V) Retained Accessory Power Power windows and audio system remain operational after ignition is switched off for 10 minutes or until a door is opened Wiring Provision for: EXTerior Lamps Flashing Forward lamp in-line connector for Exterior Lamp Flashing System (see option 6j7 on page 6) Wiring diagrams See pages 18 through 21 for description; or the owner’s manual

EXTERIOR FEATURES Antenna Radio, roof mounted (center of roof near rear window) Body Side Moldings Not available Defogger Electric, rear window Door Handles Black Door locks Power door locks automatically locks doors when transmission is out of Park. Customer can re-program to disable door locking and unlocking via the radio vehicle customization menu. (See page 9). A key lock cylinder is standard on driver and front passenger doors; child safety locks in rear doors. Options 6N5 and 6N6 are available to disable rear door windows and rear door latch/locks Headlamps Halogen, automatic lamp control with daytime running lamps. (For Daytime Running Lamps Delete see option VVS on page 6) HORN Dual note (high and low) Keyless entry Includes two integrated keys and transmitters; the keyless entry system is programmed in a “stealth mode”: When the remote transmitter “unlock” or “lock” is operated, no exterior lamps or sounds are activated. Interior lights will come On when the remote lock/unlocks are activated unless the front overhead console dome lamp switch is Off. Keys 2 keys with integrated remote keyless entry, side milled, two-sided, with folding feature (see page 17 for description) random code for ignition, driver door and trunk; options 6E3 or 6E4 available for single key locking of entire fleet (see page 6). License plate front Mounting hardware included Lock CYLINDER Driver and front passenger doors with key-lock cylinder in truck lid Mirrors, outside rearview Black, electric left hand and right hand remote with manual folding (heated available; see option dr9 on page 6) Paint Base coat/clear coat Remote Vehicle Start Remote vehicle starter system includes Remote Keyless Entry Trunk Lamp Standard Trunk Lock CYLINDER Standard Trunk release Electric, ignition controlled switch, located on both front door interior panels Under hood lamp Not available Windshield wipers Intermittent, 2-speed with variable dwell

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

4 | CAPRICE

Police Package 9C1 CHASSIS FEATURES

Alternator 170-amp, with idle boost (transmission in park or neutral) controlled by battery energy level sensing Axle 2.92 axle ratio with limited slip standard with V8. Limited slip optional with V6 Battery 700 CCA. 70 amp-hr Absorbent Glass Mat (AGM) with battery run-down protection (does not protect customer installed equipment). The AGM battery is located in the trunk and is a sealed, Valve Regulated Lead Acid (VRLA) type with the electrolyte absorbed in fine glass mat separators. VRLA battery technology is spill proof under normal conditions and requires no water replenishment. An optional 700 CCA, 70 amp-hr auxiliary battery is available; see option K5S, page 6. Body Body frame integral (unibody) Brakes Power 4-wheel anti-lock heavy-duty disc brakes with police calibration Cooling Electric cooling fans, independently fused; coolant hoses are EPDM (ethylene-propylene-diene monomer); coolant is DEXCOOL, good for 5 years/150,000 miles whichever comes first (maintenance needs vary with different uses and driving conditions; see the owner's manual for information); protects from -34 to +265 F and against rust and corrosion Chassis lubrication Lubed-for-life chassis Engines Standard 3.6L V6 DOHC SIDI (spark ignited direct injection) engine with Variable Valve Timing (VVT) and FlexFuel2 (gas or E85 Ethanol). Optional (no additional charge ) 6.0L V8 with FlexFuel2 (gas or E85 ethanol) Active Fuel Management; V6 and V8 engines include wide open throttle air conditioning cut off (when overhead lamps, spotlamps, radio antennas, sirens, and other emergency equipment are installed, overall performance may be reduced) Engine cradle Steel Exhaust system Stainless steel, dual Fuel tank capacity 19 gallons (71.6 Liters), approximate Oil coolers Transmission with V6, Engine and Transmission with V8. Cooler not required with electronically assisted power steering Radio suppression Extended life - iridium tip spark plugs and wires that are designed to reduce radio frequency noise levels which may affect communications equipment including operating frequencies in the 38-MHz to 58-MHz range. The Caprice is designed with unibody construction, and multiple grounding points are provided for the vehicle electrical system. No additional ground straps are added for the Police Package StabiliTrak Stability enhancement system. An advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. Each time the vehicle is started, the StabiliTrak system is fully on. StabliliTrak can be controlled by a StabiliTrak button on the instrument panel located on the left side of steering column (see page 13). The condition of the system is displayed by an instrument panel StabiliTrak indicator light and Driver Information Center (DIC) Messages. Push once, StabiliTrak is in Performance Mode, and Traction Control is On; push and hold five seconds, StabiliTrak and Traction Control are Off; push again and Traction Control and StabiliTrak are turned back on. See transmission and Sport Mode below for Sport Mode functions Starter interrupt Prevents starter from engaging while the engine is running Steering Electrically assisted, rack and pinion, speed sensitive, variable assist Suspension 4-wheel independent with coil springs, front and rear stabilizer bars. Patrol vehicle specific shock, spring and stabilizer bar tuning Tires Goodyear p235/50r18 W-rated blackwall with compact spare (full-size spare is available; see option SG8 on page 6) Tire pressure monitor check tire pressure will show on driver message center; excludes spare tire Traction control Deactivated when police performance mode is engaged (button located on instrument panel, left side of steering column) Trans. and Sport Mode 6-speed automatic, electronically-controlled transmission provides protection against over-revving the engine in low gear; if a driver manually selects low gear, the powertrain control module automatically protects the drivetrain. Includes Sport Shift mode where maximum transmission responsiveness is required. The Sport Shift mode On/Off button is located on the instrument panel to the left of the steering column. When in Sport Shift mode, the transmission will delay upshifts and allow earlier downshifts. In addition, the transmission can sense enthusiastic driving, at which point it may delay upshifting and downshifting earlier when braking and is designed to maximize vehicle performance Wheels 18" x 8" heavy-duty steel Wheel center cap Bolt-on pressed/forged aluminium

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 | 5 POWERTRAIN

ENGINE



TRANSMISSION

AXLE

OPTION TYPE DISPLACEMENT FUEL OPTION TYPE CODE LITERS/CU. IN. SYSTEM CODE LFX V6 3.6/217 E85 FlexFuel2 or gasoline MXO/MYA 6L45 6-speed Standard auto. with OD L77 V8 6.0/364 E85 FlexFuel2 or gasoline MXO/MYC 6L80 6-speed Optional Active Fuel Management auto. with OD no additional charge

EMISSIONS -

OPTION CODE GW8 G80 (opt.) GW8 G80 (std.)

RATIO 2.92 Limited slip 2.92 Limited slip

MUST BE SPECIFIED

FE9

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State YF5 California emissions. Use for ordering vehicles that will be registered in California. NE1 CT/ME/MD/MA/NJ/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8 Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Delaware, Massachusetts, Maryland, New Jersey, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State. NC7 Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/DE/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles” NB9 Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California. NOTE: The 2014 Chevrolet Caprice Police Patrol Vehicle with the 3.6L Engine (LFX) and 6.0L Engine (L77) with Emission Option Codes FE9, NE1, and YF5 is certified to EPA Tier 2 Bin 4 standards and qualifies as ULEV (Ultra Low Emission Vehicle) under California Air Resources Board (CARB) requirements, meaning it is 50-state certified. Emission Standard: BIN4 EPA engine family or test group: EGMXJ03.6166 (LFX) and EGMXV06.0082 (L77)

TIRES -

SPEED RATED



MANUFACTURER

QUANTITY

SIZE

SPEED RATING

TYPE



Goodyear

4

P235/50R18

W

All season

NOTE: • Compact spare is standard (full-size spare is available see option SG8 on page 6)  • Due to specific requirements for performance, durability and safety, gm recommends only the original equipment tire for replacement  • Tire Plys = Tread: 2 Polyester, 2 Steel, 1 Nylon Sidewall: 2 Polyamide Total 7 Ply  • Tire chains may be used with caution. See your owner's manual for specific recommendations regarding conditions. If the vehicle is equipped with a P235/50R18 tire size use tire chains only where legal and only when necessary. Use low profile chains that add no more than 12 mm thickness to the tire tread and inner sidewall. Use chains that are the proper size for the tires. Install them on the tires of the rear axle. Don't use chains on the tires of the front axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If the chains contact the vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage the vehicle.

SEATS AND INTERIOR TRIM



STANDARD OPTIONAL

SEAT OPTIONS

ONYX

H1T

4AA

HCQ

4AA

Front bucket, cloth with heavy-duty foam, cloth rear bench, includes seatback security panel, polypropylene rear door trim, and carpeted floor covering Front bucket, cloth with heavy-duty foam, vinyl rear bench, includes seatback security panel, polypropolyene rear door trim, and vinyl floor covering

AVAILABLE EXTERIOR COLORS GYW

GII

GHY

GIG

GIE

GAN

GZ7

Hugo Blue* (Dark Blue) Meatllic

Heron White

Red Hot

Karma Metallic (Jade)

Phantom Black Metallic

Silver Ice Metallic

Mystic Green (New)

* E xtra cost (orders that contain less than 20 orders will be delayed until 20 unit minimum is received for batch production. Will Require additional lead time) Actual colors may vary 2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator

2014 Chevrolet Municipal Vehicles Technical Manual

6 | CAPRICE

Police Package 9C1 – Options

AyG air bag1, head curtain, roof rail mounted - Combined front and rear passenger (see page 24 and 25 for description) G80 Axle - Limited slip with V6 engine (Standard on V8 engine) K5S Battery, Auxiliary - Optional 700 cca, 70-amp hour AGM battery to power customer installed equipment. The auxiliary battery is connected to the charging system through an isolation relay to prevent emergency equipment electrical loads from depleting the vehicle primary battery if the engine is not running and the ignition is OFF. Located at the passenger side of the trunk (see page 16 for description) VVS delete daytime running lamps and automatic headlamps - Exterior lamps are operated manually (see page 13 for description) L77 Engine - 6.0L V8 SFI with active fuel management, includes FlexFuel capability (no additional charge) 6j7 flasher system, Exterior Lamps - drl compatible, headlamp flasher module with wiring provisions to the front compartment for ON-OFF control and optional separate flashing of front and rear lamps (see page 16 for description) 6A3 FLOOR Covering - Heavy-duty vinyl replaces production carpeting, (carpeted mats not available); included with HCQ vinyl rear seat (see page 15 for description) 6b7 hole in roof - On center line (not available with 6j5 hole) with sealing harness grommet in roof hole 6j5 hole in roof - On passenger side (not available with 6b7 hole) with sealing harness grommet in roof hole Amf keys and keyless entry transmitters - 6 cut keys, with integrated remote keyless entry; includes Remote Vehicle Start. Transmitters are not programmed. Each transmitter, including the two standard with the vehicle, must be programmed together by the customer or by a dealer at customer expense. Transmitter programming is not a warranty item. See your owner's manual for additional programming information (see page 17 for description) Note: Common frequency keyless entry for fleet keyed vehicles not available; each fleet keyed vehicle will have a different keyless entry frequency 6e3 keys common - Complete vehicle fleet, provides a single key with a specific code that is common to the door locks and ignition for all the vehicles in the vehicle fleet; key code is an alternate to seo 6e4 key common, complete vehicle fleet. NOTE: Not compatible with previous year, Caprice, Impala and Tahoe police vehicles 6e4 keys common - Complete vehicle fleet, provides a single key with a specific code that is common to the door locks and ignition of all the vehicles in the vehicle fleet; key code is an alternate to seo 6e3 key common, complete vehicle fleet. NOTE: Not compatible with previous year, Caprice, Impala and Tahoe police vehicles 6c7 lamp - Red and white front auxiliary dome, separately switched (see page 14 for description) T53 lamps - Altern­­­­­ate flashing red and blue trunk lid warning LED lamps (see page 15 for description) B42 mat - Trunk, custom, fitted, heavy-duty vinyl molded edge to keep spills contained, removable for easy cleaning (see page 15 for description) B34 mats - Carpeted front and rear (not available with 6a3 heavy-duty vinyl floor covering) Dr9 mirrors - Heated outside rearview, power, manual folding, Black 6N6 rear door locks And handles inoperative - Rear door latch release and locks are inoperable at rear inside door; locks operate only from driver's position, rear doors can be opened only from outside (see page 14 for description) 6N5 rear DOOR window switches Inoperative - Rear door windows only operate from driver’s position (see page 14 for description) HCQ seat - Rear vinyl, includes 6a3 heavy-duty vinyl floor covering SGT Speed limiter - Limits top speed to 130 mph 7x6 spotlamp, Driver - Separately fused, six inch, black housing with halogen lamp (see page 14 for description) 7X7 Spotlamp, Driver and passenger - Separately fused, six inch, black housing with halogen lamp (see page 14 for description) 7x8 spotlamp provision Driver - Includes bracket with pillar hole sealed (see page 14 for description) 7x9 spotlamp provision Driver and passenger - Includes bracket with pillar hole sealed (see page 14 for description) SG8 tire, SPARE - Full-size (includes TPM sensor not programed) (see page 15 for description) 6j3 wiring - For grille lamps and siren speaker (see page 14 for description) 6j4 wiring - For horn/siren circuit, in-line connection for customer furnished switch (see page 14 for description) W2P Wheel covers, Full - Replaces bolted-on center cap and hardware (see page 15) Autonet Mobile WiFi in-car router13 - Available through your GM Dealer (see page 17 for Description) For standard and optional illustrations, see pages 12 through 17.

1. Head curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. 13. Monthly rates apply. Visit autonetmobile.com for details and coverage map.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 - SPECIFICATIONS | 7 GENERAL Model

1EW19

Drive

Rear-wheel

EXTERIOR (in./mm) Wheelbase Overall length Overall width Overall height* Front track width Rear track width Turning diameter curb to curb (ft./m) Ground clearance* (exhaust system)

(excluding mirrors)

118.5/3010.0 204.2/5187.0 74.8/1898.7 58.7/1490.0 62.8/1596.0 63.2/1606.0 38.0/11.7 6.0/153

FRONT COMPARTMENT (in./mm) Head room Shoulder room Hip room Leg room

38.7/984.0 59.1/1501.3 57.5/1461 42.2/1072.0

REAR COMPARTMENT (in./mm) Head room

37.6/955.0

Shoulder room Hip room Leg room

59.0/1498.0 57.9/1472.1 43.2/1098.0

LUGGAGE COMPARTMENT CAPACITY (cu.ft./liters) Luggage capacity3 (includes full-size spare tire and auxiliary battery)

17.4/492.71

PASSENGER COMPARTMENT VOLUME INDEX (cu.ft./liters) EPA passenger compartment volume index3

FUEL ECONOMY RATINGS

112/3171.5

CITY/HIGHWAY/COMBINED

3.6L V6 engine4 6.0L V8 engine4

18/26/21 15/24/18

ALTERNATOR Type Amps

9G135 170



CAPRICE POLICE ALTERNATOR OUTPUT Normal, AC off 550, V6, V8

ENGINE

STANDARD

OPTIONAL

Type Displacement: liters/cu. in. Horsepower/rpm Torque lb.-ft./rpm Induction system Compression ratio Exhaust Minimum recommended fuel octane Fuel tank capacity, approximate (gallons/liters) Cooling capacity (quarts/liters) Oil with filter (quarts/liters)

V6 3.6/217 301@6700 265@4800 SIDI 11.3:1 Dual 87 19/72 10.6/10 7.1/6.7

V8 6.0/364 355@5300 384@4400 sfi 10.4:1 Dual 87 19/72 11.6/11 8.0/7.6

6-speed 11.9/11.3

6-speed 6.7/6.3

TRANSMISSION Automatic, electronically-controlled with overdrive Fluid pan removal & filter replace (quarts/liters)

AXLE RATIO With V6 Engine

2.92

With V8 Engine includes limited slip

2.92

BRAKES 4-wheel disc with ABS Front - swept area (sq. in./sq. cm) Rear - swept area (sq. in./sq. cm) Total front and rear swept area (sq. in./sq. cm) Front rotor diameter (in./mm) Rear rotor diameter (in./mm) Front rotor thickness (in./mm) Rear rotor thickness (in./mm)

Disc/Disc 310.6/788.9 211.4/537.0 522.04/3368 13.58/345 12.76/324 1.18/30 .87/22

TIRES Type Size

Goodyear Eagle RS-A all season W-speed rated P235/50R18

WHEELS Type Size

Steel 18'' X 8''

CHASSIS

1 2

Frame Engine cradle

3

Unibody Steel

Suspension 4-wheel independent with coil springs, front and rear stabilizer bars Patrol vehicle specific shock, spring and stabilizer bar tuning Steering type Electrically assisted, variable ratio, rack-and-pinion Steering ratio (non-variable) 17.5:1 on center/12.7:1 at full lock

BATTERY 500

1000

14.0V / 77° F (25° C) 13.25V / 221° F (105° C) 13.0V / 257° F (125° C) Idle 121-amps @1100 RPM (Idle Boost 3@221° F)

1500

2000

V6 V8 Idle Boost 1 = 600 RPM 650 RPM Idle Boost 2 = 700 RPM 700 RPM Idle Boost 3 = 1100 RPM 1100 RPM

3. Cargo and load capacity limited by weight and distribution. 4. EPA-estimated MPG. 5. Gross Vehicle Weight Rating 6. Maximum payload capacity includes weight of driver, passengers, equipment and cargo. 10. Curb weight with 100% fuel, fluids and standard base equipment (excludes optional content) * Published dimensions indicated are at curb weight

Type Bci group size Volts Amp hour rating Cold cranking-amps @ 0°F (-18°C) Reserve capacity @ 80°F (27°C)

STANDARD

Maintenance free LN3 12 70 700 130 minutes

VEHICLE WEIGHT (Lbs./kg.) GVWR5 Curb weight10 Payload6 (with bucket seats)

OPTIONAL AUXILIARY

Maintenance free LN3 12 70 700 130 minutes V6

V8

5247/2380 5357/2430 4043/1834 4162/1888 1182/536 1173/532

NOTE: See your vehicle tire and loading information label for specific weight values. See your owner's manual supplement for proper cargo loading distribution

2014 Chevrolet Municipal Vehicles Technical Manual

8 | CAPRICE

Police Package 9C1 - Dimensions

Body side moldings not available

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police 9C1 DRiver Information center | 9 Certified Speedometer/cluster

3 2

4 rpm x1000

5 eco

6

Captured Speed

2

1

77

7 0

8

MPH

659 mi

80 90 60 70 100 50 110 40 120 CERTIFIED 30 130 20 140 150 10 0 160 PRNDL

Driver Information Message Center Messages shown Messages displayed are dependant on vehicle variant not all messages may display BATTERY SAVER ACTIVE

AUTOMATIC LIGHT CONTROL - ON

LOW BATTERY

AUTOMATIC LIGHT CONTROL – OFF

SERVICE BATTERY CHARGING SYSTEM

CHECK (LAMP NAME) LAMP

BRAKE FLUID LOW

CHECK (INDICATOR NAME) LAMP

SERVICE BRAKE ASSIST

INDICATOR ON TURN SIGNAL LEFT OR RIGHT

CRUISE SET TO XXX

SERVICE TRACTION CONTROL

DRIVER DOOR OPEN

SERVICE STABILITRAK

HOOD OPEN

THEFT ATTEMPTED

LEFT REAR DOOR OPEN

SERVICE AIR CONDTIONING SYSTEM

PASSENGER DOOR OPEN

SERVICE VEHICLE SOON

RIGHT REAR DOOR OPEN

SERVICE POWER STEERING

TRUNK OPEN

TURN STEERING WHEEL TURN KEY OFF & ON

A/C OFF DUE TO HIGH ENGINE TEMPERATURE

TURN STEERING WHEEL START VEHICLE AGAIN

ENGINE OVERHEATED – IDLE ENGINE

Service Tire Monitor System

ENGINE OVERHEATED – STOP ENGINE

Tire Learning Active

CHANGE ENGINE OIL SOON

Tire Pressure Low Add air to tire

OIL PRESSURE LOW – STOP ENGINE

SERVICE TRANSMISSION

ENGINE OIL LOW – ADD OIL

SHIFT DENIED

ENGINE POWER IS REDUCED

SHIFT TO PARK

FUEL LEVEL LOW

TRANSMISSION HOT – IDLE ENGINE

Speedometer certification

ICE POSSIBLE DRIVE WITH CARE

2014 Caprice police cars certified speedometer calibration. Specifications, at ambient temperature of -10 to 120 degrees F. Inaccuracies due to speed sensing are included. Actual vehicle speed indicated speed 0 to 120 mph +/- 2 MPH

WATER FLUID LOW ADD FLUID OPEN THEN CLOSE /DRIVER/PASSENGER WINDOW Captured Speed

The speedometer calibration is for the 6.0L V8 engine, automatic transmission with a 2.92 axle and P235/50R18 tires, and the 3.6L V6 engine, automatic transmission, 2.92 axle and P235/50R18 W-rated tires

2014 Chevrolet Municipal Vehicles Technical Manual

10 | CAPRICE

Police 9C1 DRiver Customization Feature

3 2

4 rpm x1000

5 eco

6

Captured Speed

2

1

77

7 0

MPH

8

659 mi

80 90 60 70 100 50 110 40 120 CERTIFIED 30 130 20 140 150 10 0 160 PRNDL

Driver Information Message Center Viewing the Driver Information Center (DIC) requires the engine to be running. The DIC in the center of the instrument cluster displays information and warnings about the vehicle.

Driver information Selector

SET/ CLR

MEN

U

The DIC is operated via the controls on the Turn Signal lever at the left side of the steering column The SET/CLR button sets or clears the displayed menu The MENU button displays the SPEED, UNIT and ECONOMY menus. The momentary ROTARY SWITCH control will scroll through the MENU items.

Press MENU until the SPEED is displayed Turn the ROTARY SWITCH to scroll through the menu items: SPEED, UNIT, ECONOMY > SPEED >Digital Speed >Fuel Used >Average Speed >Instantaneous Fuel Economy >Average Fuel Economy >Fuel Range >Trip >Capture Speed

>UNITS >Engine Hours, Idle Hours >Battery Voltage >Coolant Temp >Remaining Oil Life >Tire Pressure >ECONOMY >Best Score >Economy Trend

Note: Other vehicle features can be programmed via the radio. See also the Owners Manual for additional DIC features information.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police 9C1 DRiver Customization Feature | 11 Back

Home

Home Page

69 ˚F 1:21 PM

Fav

1 of 2

Phone

PANDORA

STITCHER

AM

FM

Stitcher

2 of 2

AUX

Bluetooth

Tone

i CD

USB

Menu

Config

More

HOME FAV

TUNE MENU

SOURCE

TONE SEEK

Quick Info

Pictures

Menu CONFIG

SEEK

69 ˚F 1:21 PM

Fav

SMART RADIO

Pandora

VOL

Home

Home Page

Now Playing

internet radio

Back

More

The Following Items Are Permanently Disabled on Caprice: USB Picture Viewer AUX In

BACK

ELECTRICAL FUNCTION CUSTOMIZATION FEATURE With Radio OFF “Day, Date, Time, Exterior Temperature, and Chevrolet MyLink“ are displayed (Display Screen can be turned off, see DISPLAY SETTINGS) CONFIG Languages Time and Date Radio Settings Phone Settings Display Settings Vehicle Settings

Comfort and Convenience (Factory defaults in Bold) Chime volume Normal/High Button chime Buttons ‘click’ when touched: On/Off

Display Settings Home Page Menu > Customize >Sort > Restore Home Page Defaults Display Off This button blanks radio screen, touch screen anywhere to restore.

Power Door Locks (Factory defaults in Bold) Door Open Anti-Lockout >On/Off Auto Door Lock > On/Off Auto Door Unlock > All Door > Driver Door > Off Delay Door Lock > On/Off

Vehicle Settings Climate and Air Quality Comfort and Convenience Lighting Power Door Locks Remote Lock/Unlock/Start Return to Factory Settings

Remote Lock/Unlock/Start (Factory defaults in Bold) Remote Unlock Feedback > Flash Lights, > Off Remote Lock Feedback > Lights Horn > On/Off > Lights Only > On/Off > Horn Only > On/Off > Off Remote Door Unlock > Driver Door > All Doors

Lighting (Factory defaults in Bold) Vehicle Locator Lights On/Off Exit Lighting >Off >30 sec >60 sec >120 sec

Yes/No

NOTE: R efer to the Owners Manual for detailed HOME PAGE icon setup and other radio function information. Menu items in Red describe customization typical for law enforcement usage. Bold Underlined status is factory default condition

2014 Chevrolet Municipal Vehicles Technical Manual

12 | CAPRICE

Police 9C1 special equipment - Standard Center Console Equipment Mounting Platform

V8 ENGINE OIL COOLER Engine Oil Cooler Engine Coolant Lines

The oil-to-coolant engine oil cooler system is mounted on the left side of the lower engine block, forward of the oil filter. Engine oil flows through the stacked plate cooler from the engine oil sump and returns to the engine. Coolant flows to the cooler via a short hose from the engine block and exits to the radiator through a coupled hose connection to the radiator inlet hose. NOTE: Not required with V6 engine.

Center front equipment mounting platform between front seats, 27x9 inches, slotted for T-bolt attachment of customer equipment.

Keylock Cylinder - Trunk Lid

Transmission OIL COOLER

An audible alarm may occur when the ignition key is used to open the trunk instead of the Remote Keyless Entry (key fob). Transmission Cooler

The transmission cooler is positioned to the left side, in front of the air conditioning condenser. The cooling system is common to the V6 and V8 engines

CAPTURED SPEED

Service parts identification label SERVICE PARTS IDENTIFICATION

E L MP

6G1MK5T22BL532613 eco

Captured Speed

77 MPH

659 mi This vehicle is equipped with a standard feature that allows an officer to capture speed of the Caprice while pacing another vehicle. To activate Captured Speed, the Driver Information Center must be selected to display Speed. Once the pace is established, push the outer button on the end of turn stalk to “Capture Speed”. The digital speedometer will return momentary back to active speed. To display Captured Speed, rotate stalk wheel clockwise. This Captured Speed is retained even after ignition key is turned off, or up until a new speed is captured or cleared. To clear the current Captured Speed, push and hold the outward end of stalk button until a beep signifies that system has been reset.

AGK BDR IPG OST UW6 3FL 7X6 BC/CC

AG2 B3B JA9 QPP UIC 6A3 8MZ

AL0 AMF B42 B86 JL9 KD1 R7V R9N U77 VT7 6E2 6HP 9C1 9MZ U 636R

DO NOT REMOVE

AP3 B9V KG4 R9Z V8D 6J1

SA

AR9 C67 LGD SLM WL9 6J3

AT8 DK2 MX0 T53 ZFH 6J4

PDBJCH AXJ AY0 EF7 E2C M15 NK5 UH8 UJM 1SZ GAN 6J7 7B3

A75 FE9 NT7 UN9 4BB 7HP

1EW19 A76 FR9 N99 UT7 191 7M9

A Service Parts Identification (SPID) Label provides Vehicle Identification Number (VIN)-specific Option Code content list, Engineering Model Number (Nameplate, body style), Exterior paint system, Exterior paint color code and Interior trim level and color. The SPID label for the Caprice is located on the underside of the rear compartment lid at the center of the lid inner reinforcement.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police 9C1 special equipment - Standard | 13 WIRING PROVISIONS FOR 12-VOLT BATTERY POWER SUPPLY

AUXILIARY POWER and ground stud in trunk Ignition Power (white connector)

50 amp battery power to front compartment upfitter harness

Rear compartment power studs

Pre-fuse assembly

Auxiliary battery power, ground, relay controlled battery power and control circuits are terminated in three connectors located at the right front of the equipment mounting platform. Battery power is supplied through two pre-fuse assembly fusible links located at the right side of the trunk. If the optional auxiliary battery (RPO K5S) is not present, power to the pre-fuse assembly is supplied by the primary battery. Three circuit breakers and two control relays are located in the right side of the trunk. The relay center is connected via the body harness to the front compartment auxiliary power and signal connectors. A 50 amp circuit breaker feeds power directly from the 100 amp fusible link via a 10 gauge (5.0 mm) wire. Two 30 amp circuit breakers supply power from fusible links through the contacts of the control relays to 12 gauge (3.0 mm) wires. Each relay is operated by control leads terminated in the front compartment 6-cavity connector. A 10 gauge (5.0 mm) ground circuit is terminated in the 2-cavity connector with the 50 amp battery power. A total of 1320 watts of 12 volt power is available in the front compartment. 1440 watts of 12 volt power is available at the trunk junction block.

An auxiliary power junction block is located at the right side of the trunk. The junction block is at the rear of the auxiliary battery tray and contains a split buss with two terminals for customer connection to 12-volt battery power.

NOTE: If 50-amp battery power is not present at the front compartment upfitter harness, verify the connection of the topmost (blue) of two connectors located above the right hand rear compartment junction block. For wiring diagram see pages 18 and 19. See also page 13, Rear Auxiliary Power and Ground Stud and page 16, K5S, Auxiliary Battery.

An 8 mm ground stud for customer connection is located at the inboard front corner of the right side battery tray.

Dome LAMPS CONTROL

8 mm ground stud Circuit breakers and relays for front compartment auxiliary power

The split bus is connected to the primary battery located at the left side of the trunk. When the optional auxiliary battery (RPO K5S) is present, the split bus is connected to the auxiliary battery through an isolation relay. Two 60-amp fusible links connect the bus to the battery. Maximum combined capacity of the two circuits is 1440-watts.

A Violet/Yellow ignition controlled power circuit, HOT in RUN/START, terminates in a white connector located above the auxiliary battery power junction block. This same circuit is also located in the front passenger foot well upfitter harness. A 10-amp fuse (EF131) protects both circuits and is located in the engine compartment fuse center. The total power available for the combined front and rear circuits is 60 watts. NOTE: For wiring diagram see page 17

EXTERIOR LAMPS CONTROL A

B

Buttons are located in front dome lamp assembly A – The push on/push off left switch with a Doors Open symbol on the front dome lamp assembly controls the front and rear dome lamps. When activated, the dome lamps will remain Off whenever: any door is opened, the vehicle is unlocked, or the key is removed from the ignition switch. B - The push on/push off right switch with a Dome Lamp symbol on the front dome lamp assembly turns the front and rear dome lamps On and Off.

Locations of Sport Mode and Stabilitrak buttons

S

VVS – Delete Daytime Running Lamps and Automatic Headlamps. This option disables the Daytime Running Lamps and Automatic Headlamps control feature. Exterior lamps are manually controlled only. Option VVS is not available in Canada. The headlamp control on the driver’s side of the instrument panel operates the headlamps. If your Caprice does not have option VVS, Daytime Running Lamps and Automatic Headlamps Delete, the Daytime Running Lamps and Automatic Headlamps can be turned off for one ignition cycle by rotating the control knob momentarily counterclockwise. Rotating the headlamp switch again will turn the daytime running lamps or automatic headlamps back on. In Canada, the Daytime Running Lamps and Automatic Headlamps can be turned off if the transmission is in Park. See also Caprice owner’s manual.

Located on instrument panel left side of steering column.

2014 Chevrolet Municipal Vehicles Technical Manual

14 | CAPRICE

Police 9C1 special equipment - OPTIONAL

6J4 WIRING PROVISION FOR horn/ siren circut

Two 16-gauge wires are connected to an in-line connector in the horn circuit of the instrument panel harness under the instrument panel. The end of this harness extension is terminated with an in-line connector in a 60-inch (1.5 m) coil under the instrument panel. Connection to customer switching permits operation of the horn or siren with the horn button.

6J3 WIRING PROVISION FOR vehicle grille Lamps and speaker/siren

The SEO 6J3 wiring provision circuits are terminated at a 16-way connector on the upfitter harness at the front of the equipment mounting platform. The wiring circuits are routed from under the instrument panel to a 2-foot (610 mm) coil secured in the area behind the grille, to the left of the hood latch assembly. NOTE: For wiring diagram see page 20

NOTE: For wiring diagram see page 20

7x6 and 7X7 Spotlamps 7X8 and 7X9 Spotlamp Provisions

7x6 Spotlamp left hand, pillar-mounted unity, 6-inch with replaceable h3 halogen bulb; independently fused 7x7 Spotlamps left and right hand, pillar-mounted unity, 6-inch with replaceable h3 halogen bulb; independently fused 7x8 Spotlamp provision left hand provision for customer installed spotlamp includes hole through pillar, mounting bracket and accessible power connector 7x9 Spotlamp provision left and right hand includes same components as option 7x8

6C7 Lamp - Auxiliary Dome

Red and white auxiliary dome lamp is located to the rear of the vehicle dome lamp (red is LED and white is incandescent). The auxiliary lamp is wired independently from the standard dome lamp.

6N6 - Rear Door locks and handles Inoperative

NOTE: • Lamp bulbs are halogen 12volt 100 watt H-3 rated at 245,000 candle power • For wiring diagrams and fuse location see page 20 • Customer furnished spotlamp assembly must be installed to avoid interference with deploying passenger airbag

6N5 Window SWITCHES REar door Inoperative Rear doors can only be opened from the outside. Locks operate only from driver door switch

Rear door window switches are inoperable. Rear door power regulators are operable only from driver position switches.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police 9C1 special equipment - OPTIONAL | 15 B42 Mat - Trunk

Custom fitted, heavy-duty vinyl molded edge to keep spills contained, removable for easy cleaning

T53 LAmps - Trunk Lid Warning

Two 4-inch, single faced, red and blue LED lamps are mounted to the deck lid inner panel. Lamps are activated by the deck lid ajar mechanical switch when deck lid is opened. Lamps are wired to flash alternately through a flasher located at the upper right hand corner of the trunk opening. Wiring is protected by fuse F8 in the rear fuse block located on top of the standard battery in the trunk.

SG8 FULL SIZE SPARE

Full-size spare tire is mounted under the load floor. The full-size spare tire includes a Tire Pressure Monitor (TPM) sensor which must be programmed to the TPM System after the spare tire is installed.

6A3 Covering - Floor

Black heavy-duty front and rear. Replaces production carpeting.

6B7 and 6J5 Hole in Roof Panel

6B7 Hole is drilled near center line of roof panel approximately 29 inches rearward of windshield opening. Includes sealing harness grommet in roof hole 6J5 Hole is drilled on passenger side of roof panel approximately 29 inches rearward of windshield opening and approximately 6 inches inboard from passenger side door. Includes sealing harness grommet in roof hole NOTE: Only one roof hole location may be ordered.

W2P FULL WHEEL COVER

Plastic wheel cover attaches to threaded lug nuts

2014 Chevrolet Municipal Vehicles Technical Manual

16 | CAPRICE

Police 9C1 special equipment - Optional

6J7 FLashing system EXTERIOR LAmps Module location

The Option 6J7 Exterior Lamps Emergency Flashing Module mounting location at the rear edge of the upper right hand radiator support.

K5S – Auxiliary Battery 50 amp battery power to front compartment upfitter harness Ignition Power (white connector)

Auxiliary Battery

Rear compartment power studs

6J7 flashing system, EXTERIOR LAmps

Option 6J7 provides a headlamps high beam flashing module, rear lamps flashing via the Body Control Module (BCM) and a control wire for customer-furnished switching to turn the module on and off. The flasher control wire is terminated in the 16-way connector on the upfitter harness at the right front corner of the equipment mounting platform. The flashing module is located is located on the rear side of the passenger side upper radiator support The headlamp flashing module is activated by the application of 12 volts to a dark green wire in the upfitter harness. When activated, the headlamp high beams and the high beam instrument cluster indicator will flash alternately at 2.4 flashes per second. When the flashing module is turned on, the module sends a signal to the BCM which alternately flashes the stop lamps and backup lamps at the same flash rate as the headlamps. Depressing the brake pedal will override the stop lamp flashing and placing the transmission in Reverse will override the backup lamps flashing. During daylight conditions, the Daytime Running Lamps (DRL) are automatically turned off whenever the headlamps flashing module is activated. During night time conditions, the low beam headlamps automatically turn on while the high beam lamps flash. Turning on the high beam headlamps manually will override the flashing module and the high beam headlamps will operate continuously. During night time conditions the tail lamps will turn on automatically. If Option VVS is present the low beam headlamps and tail lamps will not come on automatically. The Center Mounted Stop Lamp will operate only when the service brakes are applied. A 15-amp fuse labeled EF35 protects the flasher module circuit. The fuse is located in the under hood fuse block in the engine compartment on the passenger side of the vehicle. See also the Owner Manual for more information.

8 mm ground stud

Pre-fuse assembly

Isolation relay

Option K5S, Auxiliary Battery, consists of a 700 CCA battery mounted at the right side of the rear compartment and is connected to the electrical system via a Pre-fuse Assembly. Also included is an isolation relay which is activated whenever the ignition is ON. The isolation relay is intended to isolate the auxiliary battery and connected load from the primary battery to avoid unintended rundown of the primary battery. Whenever the ignition is ON and the engine is running, the primary battery and auxiliary batteries are being charged, as determined by the charging system controls.

Activation of the headlamps flashing and rear lamps can be separated by opening the blue/green BCM circuit at the flasher module connector, P181-F, and applying a customer-switched ground to the blue/green wire in the upfitter harness 16-cavity connector (P277-16) at the right side of the equipment mounting platform. Power to the green wire must be OFF to flash rear lamps only. Warning: BCM will be damaged if 12V power is connected to the dark-blue/ yellow wire.  NOTE: For wiring diagram see page 18

A Violet/Gray ignition controlled power circuit, HOT in RUN/START, terminates in a white connector located above the auxiliary battery power junction block. This same circuit is also located in the front passenger foot well upfitter harness (see page 19). A 10-amp fuse (EF26) protects both circuits and is located in the engine compartment fuse center. The total power available for the combined front and rear circuits is 60 watts.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police 9C1 special equipment - Optional | 17 KEYS and TRANSMITTERS Part Number

Description

AMF - PACKAGE OF 6 KEY and TRANSMITTERS

KEYS

13585404 Key/Transmitter Assembly, Door Lock and Ignition Lock, (CUT KEY) Master (AX2) Random Cut 13585687 Key/Transmitter Assembly, Door Lock and Ignition Lock, (UNCUT KEY) Master (AX2) Key Blank See Dealer Key/Transmitter Assembly, Door Lock and Ignition Lock, (CUT KEY) Fleet (AU7) Keyed Alike (6E3) See Dealer Key/Transmitter Assembly, Door Lock and Ignition Lock, (CUT KEY) Fleet (AU7) Keyed Alike (6E4) 13585688 Key/Transmitter Assembly, Door Lock and Ignition Lock, (UNCUT KEY) Fleet (AU7) Key Blank (6E3/6E4) 92271667 Key, Door Lock and Ignition Lock, (UNCUT KEY) Master (AX2) Key Blank (Basic Key with Blank Transmitter) 92271668 Key, Door Lock and Ignition Lock, (UNCUT KEY) Fleet (AU7) Key Blank (6E3/6E4) (Basic Key with Blank Transmitter) See Dealer Key, Door Lock and Ignition Lock, (CUT KEY) Fleet (AU7) Keyed Alike (6E3) (Basic Key with Blank Transmitter) See Dealer Key, Door Lock and Ignition Lock, (CUT KEY) Fleet (AU7) Keyed Alike (6E4) (Basic Key with Blank Transmitter) 19302076 Key, Door Lock and Ignition Lock, (CUT KEY) Master (AX2) Random Cut (Basic Key with Blank Transmitter) KITS See Dealer Key, Door Lock and Ignition Lock, (CUT KEY) Fleet (AU7) Keyed Alike (6E3) (Package of 6 Basic Keys with Blank Transmitter )

Autonet Mobile wifi; in-car router

Key retraction button Unlock Vehicle Trunk Release

Lock Vehicle Remote Vehicle Start

Panic

(non functioning)

Option AMF: Package of 6 Keys and Transmitters, includes 6 cut keys with integrated remote keyless entry (Transmitter are not programmed). Each transmitter including the two standard with the vehicle, must be programmed at the same time by the customer or by a dealer at customer expense. Transmitter programming is not a warranty item. Common frequency keyless entry for fleet keyed vehicles not available; each fleet keyed vehicle will have a different keyless entry. See your owner's manual for additional programming information. New Key LEARN Procedure 1. The six RPO AMF keys are pre-cut at vehicle assembly. If a key is separate from AMF, cut the new key blank to match the vehicle key (master) 2. Using the master key, turn ON the ignition, with the engine OFF 3. Turn OFF the ignition and remove the key 4. Within 10 seconds of turning OFF the ignition, insert the key to be learned and turn ON the ignition. The vehicle has now learned the new key. Remote Transmitter learn Procedure 1. Ignition must be ON and transmission in PARK (P) 2. Press the TRIP button until the customization trip page is reached. 3. Press the ENTER button on the enter the customization menu. 4. Scroll down to the 'Remote Key' menu item and press ENTER 5. Scroll down to the 'Program' menu item and press ENTER 6. Press and hold the LOCK and UNLOCK button on the first transmitter at the same time for approximately 15 seconds. 2 beeps will sound indicating the transmitter is matched. 7. Repeat step 6 for the additional transmitters. 8. To exit the programming mode, key the ignition to OFF. NOTE: A maximum of 10 keys may be learned for a vehicle immobilizer (Passkey III+) with a random key code. Vehicles with the fleet key option (RPO 6E3 or 6E4) may have an unlimited number of keys learned for the particular option fleet key and must be learned using one of the original "master" keys.

Delivers high speed network connectivity to vehicles by leveraging the 3G network. Autonet Mobile's TRU Technology, a proprietary and patented technology, provides a seamless connection regardless how fast you are traveling. Unlike conventional cellular data technology, TRU Technology manages data as users travel at high speeds between cell towers, eliminating dropped connections. CarFi™ provides wireless device connectivity within the vehicle using standards-based 802.11 Wi-Fi networking. This allows users in and around the vehicle to access the Internet using any Wi-Fi enabled device. Available through your GM dealer.

When programming Option AMF, additional 6 remote transmitters, the original 2 transmitters delivered with a vehicle must also be reprogrammed at the same time. A maximum of 8 remote transmitters can be programmed for a single vehicle.

2014 Chevrolet Municipal Vehicles Technical Manual

18 | CAPRICE

Police Package 9C1 – Wiring Diagrams

Wiring Diagram for 12-volt battery power supply Optional Auxiliary Battery RPO K5S (includes Isolation Relay)

J2-1 BATTERY -Auxiliary

POS

J1 J2

BATPOS

G1

CONNECTOR -Aux Fusebox 1

NEG

J1-1 2950. BARE 16.0

FUSELINK 140A

Ground-Aux Battery G405 CUSTOMER CONNECTION GROUND STUD LOCATED AT AUXILLARY BATTERY TRAY

FUSELINK 100A

J1-A

TO PRIMARY BATTERY PREFUSE CONNECTOR J2-A or AUXILIARY BATTERY ISOLATION RELAY WITH RPO K5S

FUSELINK 60A

FUSELINK 50A

J3-2

J3-1

FUSELINK 60A

J4-2

J4-1

1542 RD 6.0

1442 RD 8.0

J2-A

NOTE: FUSES IN AUXILIARY FUSEBOX 1 ARE NOT SERVICEABLE INDIVIDUALLY

SP1442

1742

1442. RD/YE 10.0

9042 RD/BU 6.0

RD/BN 6.0

SP1442

1542. RD/BU 6.0

1442 RD/YE

B

B

B J1-A

J2-A 30A

REAR COMPARTMENT AUXILIARY POWER STUDS AT RH SIDE FOR CUSTOMER CONNECTION

Maxi Breaker - 30A (Police 1) 12088553

30A

Maxi Breaker - 30A (Police 2) 12088553

J1 CONNECTOR -AUX FUSEBOX 2

A

5040. RD/YE 3.0

6340 RD/VT 3.0

ELECTRICAL CENTER -POLICE RELAYS

88

Maxi Breaker - 50A (Police 3) 15319848

J1

A

C3

50A

J1 A

C7

30

86

87

85

88

30

86

87

85

NOTE: Connectors J/P 446 A and B are located above the rear auxiliary battery power junction block at the right hand rear compartment.

J1 C1 2650

BK 0.5

B1

C5 2650.

BK 0.5

SA2650

2650 2650 0.5

BK

0.5 1 2

BK

P479 J479

B3

6839. WH/BN 3.0

1 1

J446A P446A

6839. WH/BN 3.0

B5

6842. BN 1.0

3 3

J446A P446A

6842. BN 1.0

B7

6840. GN/YE 3.0

6843. BU/YE 1.0

5240. RD/BU 6.0

2 2

4 4

1 1

J446A P446A

6840. GN/YE 3.0

J446A P446A

6 43. BU/YE 1.0

J446B P446B

5240. RD/BU 6.0

AUXILARY BATTERY ISOLATION RELAY 2950 BK 5.0

2650

Ground Dist G402 1

P278

Police relay outputs and control circuit connections are terminated in 3 connectors at the right front of the equipment mounting platform. Battery power is supplied through two fusible links, one 100 amp and one 60 amp, to three circuit breakers and two control relays located in the trunk relay center. A 50 amp circuit breaker feeds power directly from the fusible links through a 10 gauge (6.0 mm) wire. Two 30 amp circuit breakers

3

P278

2

P278

4

P278

1

P280

2

P280

Ground Dist G405

supply power from the fusible links through the contacts of the control relays to 12 gauge (3.0 mm) wires. Each relay is operated by an 18 gauge (1.0 mm) brown or blue/ yellow control lead terminated in the 6 cavity connector. A 8 gauge (8.0 mm) ground lead is provided in the 2 cavity connector. The total current available through the 12 volt power supply is 110 amps (1320 watts).

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 – Wiring Diagrams | 19 Wiring Diagram for Controlled power and signal circuits with 12-volt power supply MODULE Body Control

MODULE Electonic Brake Control

MODULE Body Control

UNDERHOOD BEC

REAR CENTER

EF26

EF131

Wiring Diagram for headlamp and rear lamps flashing system – 6J7 MODULE 12 VOLT ON CONNECTION

SEPARATION OF FRONT AND REAR FLASHING

TO UNDERHOOD BATTERY ELECRICAL CENTER EF16

EF35

BCM

EF16 15

P277

16

P277

6841. BU/GN 0.5 6820. 6821 WH/VT 0.35

1

P277

Surveillence Mode

381 WH/BK 0.35

2

P277

Vehicle Speed Output

539 VT/GY 0.35

5810 YE 0.35

3

P277

HOT OUT OF PARK

5

P278

HOT START & RUN

GN 0.5

343 VT/YE 0.35

6

P278

HOT ACCY & RUN

Ignition controlled power and signal circuits are also included in the 6 cavity and 16 cavity upfit connectors.

• A violet/yellow 10 amp fused circuit, HOT in ACCESSORY/RUN; fuse EF131 is in the end of the instrument panel. • A violet/gray 10 amp fused circuit, HOT in START/RUN; fuse EF26 is in the engine compartment fuse block. This circuit is also located at the RH side of the trunk in a white connector above the rear auxiliary power junction block (see page 13). Total power available for the combined front and rear circuits is 60 watts. • A yellow Park signal from the Body Control Module (BCM). This circuit provides switched 12 volt power when the transmission is not in PARK (P) and the engine is running. The electrical load attached must not exceed 0.5 amps (one relay coil). • A white/black vehicle speed signal (4000 pulses per mile) from the ABS module. Connect only a high impedance load. • A white/violet Surveillance Mode circuit. When grounded, all automatic lighting is suppressed and the radio display is OFF.

Surveillance Mode MODULE Electonic Brake Control

MODULE Body Control

711

WH 0.35

250 BK 0.75

Gnd Dist G104

6820.

A

P181 B B

P181 C J181

REAR CENTER EF131

1

P277

Surveillence Mode

381 WH/BK 0.35

2

P277

Vehicle Speed Output

539 VT/GY 0.35

5810 YE 0.35

3

P277

HOT OUT OF PARK

5

P278

HOT START & RUN

P181 D D

P181 E

53

X209

7 7

J126 P126

6841. BU/GN 0.5

P181

F

P181

J181 P181 INLINE CONNECTOR FOR HEADLAMP FLASHER MODULE AT TOP RIGHTHAND RADIATOR SUPPORT

WH 0.35

EF26

J126 P126

GN 0.5

711.

UNDERHOOD BEC

6841. D-BU/YE 0.5

311 WH 0.35 6 6

LF High Beam 6821 WH/VT 0.35

SA6841

5340 RD/VT 0.75

P277 LOCATED IN RIGHT FRONT FOOT WELL

MODULE Body Control

6841. BU/GN 0.5

311. WH 0.35

RF High Beam

343 VT/YE 0.35

6

P278

HOT ACCY & RUN

When the vehicle lighting system is in the Automatic Mode (Headlamp switch in the AUTO position) and night time conditions exist, the exterior lighting will automatically come ON. In day time conditions, the Daytime Running Lamps (DRL) will be ON. Surveillance Mode is a standard feature in the Caprice Police vehicle. The Surveillance Mode circuit is terminated in cavity 1 of the 16 cavity upfitter connector P277, located at the passenger side front of the equipment mounting platform. When Surveillance Mode is activated by applying a ground to the White/Violet wire in cavity 1, all automatic lighting functions are suppressed. All manually operated lighting controls remain functional, e. g., exterior lamps, turn/stop. If RPO VVS, DRL and AUTO HEADLAMPS Disabled is present, exterior light is manually controlled; all other listed items are suppressed when Surveillance Mode is activated.

An in-line connector in the forward lamp harness permits installation of a compatible flasher module for the exterior lamps Emergency Flashing System. The in-line flasher module connector is located at the RH end of the upper radiator support and includes two wiring circuits to the front compartment foot well. A green wire is intended for customer connection to switched 12 volt power to activate the flasher module. A second blue/green wire permits optional separate control of the headlamp flashing and rear lamps flashing. Separate control of the rear lamps flashing requires opening the blue/green control circuit at the in-line connector terminal P181-F and application of switched vehicle ground to the control wire in the forward compartment, P27716. Power to the blue/green wire must be OFF to flash rear lamps only.

Warning: BCM will be damaged if 12V power is connected to the dark-blue/ yellow wire. 

• Radio Display is OFF (If the radio is ON, the audio remains on in the Surveillance Mode). • Instrument Cluster is OFF (PRNDL remains barely discernable per FMVSS 101). • Low Beam Headlamps are OFF; DRL are OFF during daytime. • High Beam Headlamps are OFF, Flash-to-Pass remains functional. • Tail Lamps are OFF (Stop Lamps and Turn Signals remain functional) . • License Lamps are OFF. • Dome Lamps are disabled (inoperative at the lamp switches) and remain off when a door is opened. All interior lighting is OFF, e. g., controls, HVAC, glove box, trunk. • Auxiliary Dome Lamp (RPO 6C7) is functional but locally switched at the lamp base. • Remote lock/unlock audible/visual functions are OFF; horn chirp OFF when a door is open with remote lock requested. NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

20 | CAPRICE

Police Package 9C1 – Wiring Diagrams

Wiring Diagram FOR HORN/SIREN CIRCUIT - OPTION 6J4

Wiring Diagram FOR GRILLE LAMPS AND SIREN/SPEAKER - OPTION 6J3

Body Control Module X3

P18

COILED UNDER INSTRUMENT PANEL

3287 GN/WH 0.35

Siren

14

A A

J274 P274

P277

6837 BU/GN 1.5

3287 GN/WH 0.35

100 100

Grille Lamps

13

P277

6836 GN/YE 1.5

101 101

P209 J209

P209 J209

11

P277

6838 GY/VT 1.5

97 97

6837 BU/GN 1.5

6836 GN/YE 1.5

6838 GY/VT 1.5

5 5

8 8

6 6

P355 J355

P355 J355

12

P277

6835 YE/GN 1.5

98 98

P209 J209

P209 J209

6835 YE/GN 1.5 P355 J355

7 7

P355 J355

BK/WH

CONNECTOR -Clock Spring 6837 BU/GN 1.5

6836 GN/YE 1.5

6838 GY/VT 1.5

A

B

C

3287 BK/WH 0.35

P182

P182

6835 YE/GN 1.5

P182

D

P182

Blunt cut wires coiled at upper radiator support

Steering Wheel

Two 20-gauge (0.5 mm2) wires are connected to an in-line connector in the horn circuit of the instrument panel harness under the instrument panel. The end of this harness extension is terminated with an in-line connector in a 60-inch coil under the instrument panel. Connection to customer switching permits operation of the horn or siren with the horn button.

The SEO 6J3 wiring provision circuits are terminated in the 16 cavity connector at the front of the equipment mounting platform on the passenger side. The wiring circuits are routed from the passenger compartment to a 2 foot (30 cm) coil secured in the area behind the grille. There are four 16 gauge (1.5 mm) wires for connecting to the grille lights and siren speaker.

Wiring Diagram for WINDSHIELD PILLAR-MOUNTED SPOTLAMP - OPTION 7X6 and 7X7

EF42 Minifuse 15A

UNDER HOOD ELECTRICAL CENTER EF41 Minifuse 15A

-Spotlamp LH 5440 0.5

RD/WH

J281

P281 A

RD/WH

5440 0.5

RD/GY

5540 0.5

H7635

A PWR

CASE GND

-Spotlamp RH 5540 0.5

RD/GY

J282

P282 A

H7635

A PWR

CASE GND

7x6 spotlamp left hand and 7X7, spotlamps left and right hand, pillar-mounted Unity, 6-inch with replaceable h3 halogen bulb; independently fused NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 – Wiring Diagrams | 21 WIRING PROVISION - 25mm Access hole - RH Dash Panel Front of Dash A

A

B

C

RH Front Body Hinge Pillar

Cabin air filter below RH end of Cowl grille (raised)

A) Blanking grommet through front of dash below the oval wire grommet B) Bulkhead in filter chamber C) Possible upfit harness routing C

2014 Chevrolet Municipal Vehicles Technical Manual

22 | AIR

BAG FAQ

Can specialty vehicle equipment (e.g. radar devices, video cameras, computers, meters, radio trees, shotguns, etc.) still be mounted in cars with passenger side air bags? Yes, but care must be taken to mount the equipment outside of the deployment zone. Air bags inflate with great force and will interact with any object in the deployment zone. Therefore, to reduce the risk of injury to vehicle occupants, GM recommends that the air deployment zone be kept free of any equipment. If a piece of equipment were to become dislodged it could strike an occupant in the vehicle and result in injury. The likelihood of an object becoming dislodged is influenced by many factors, including the proximity of the object to the inflatable restraint, the size and shape of the object, and the means by which the object is secured to the vehicle. In addition to these factors, the trajectory and velocity of a dislodged object can be influenced by the type and severity of vehicle crash. Objects that are in the deployment zone, but do not become dislodged by an inflating air bag can still affect the performance of the air bag. For example, such objects could tear the fabric or affect the shape of the air bag, thus reducing the ability of the bag to provide restraint. Is it possible to shield equipment that is installed in the passenger side frontal air bag deployment zone in a manner that will allow full and safe air bag deployment? Due to the complexity of influencing variables, GM is unable to evaluate the potential for shielding expected equipment configurations in all accident scenarios in order to assure that the air bag performance would be unaffected. While shielding may protect certain equipment from being damaged or dislodged, it may also negatively affect the inflation characteristics of the air bag. The air bag’s shape, inflation angle, fold pattern, and inflation rate and pressure are developed to maximize the protection capability of the inflatable restraint system. Therefore, GM cannot recommend the placement of any equipment in the deployment zone, even if it is shielded to protect it from damage. Front air bag systems and instrument panel mounted equipment. Passenger air bags in GM vehicles deploy in different ways depending upon the type of vehicle and the particular instrument panel design. In some vehicles, the passenger air bag deploys through a discrete door located on the top surface of the instrument panel (top-mount air bag systems). In other vehicles, such as the Chevrolet Tahoe, the passenger air bag deploys through a discrete door mounted on the vertical rearward surface of the instrument panel, above the glove box door (mid-mount air bag system). With these types of topmount and mid-mount passenger air bag systems, the top pad of the instrument panel remains in place during deployment. Some GM passenger air bag systems, like the system in the Chevrolet Impala, deploy from beneath the instrument panel top pad. These are considered 3/4-mount air bag systems with a “deployable top pad.” The entire instrument panel top pad is the “deployment door” from under which the inflating air bag emerges. When an air bag deployment is commanded, the forces from the inflating passenger air bag push up on the instrument panel top pad, releasing special fasteners across the rearward edge of the top pad. This allows the top pad to rotate upward so that the passenger air bag may emerge. The top pad rotates upward to open widest at the right hand side, and is usually forced upward into contact with the windshield on the right hand side of the vehicle during a deployment.

Instrument panel top mounted special equipment, such as a radar antenna and control unit or video camera must be positioned to the left of the vehicle center line. This equipment must be mounted as low as possible and securely fastened to the top pad to avoid being dislodged in the event of a crash and possible air bag deployment. In the process of securely fastening special equipment to the top, DO NOT fasten down the top pad itself to any other vehicle component such as the cluster trim plate. As described above, the top pad rotates upward during a deployment. In order to enable the proper deployment of the passenger air bag, specialty equipment installation MUST NOT PREVENT the top pad from rotating upward during deployment. Location and attachment of special equipment should minimize added resistance or interference to upward rotation of the top pad during deployment. Side-Impact Air Bags for crashes to the vehicle sides. The air bag system in your police vehicle includes includes roof rail mounted Head Curtain side air bags.. The vehicle is also equipped with seat back mounted upper body air bags located on the outboard side of the driver and front passenger seat backs. Together the Head Curtain and seat-mounted side air bags are intended to protect the head and upper body in the event of a side crash. Some vehicles may also be equipped with an optional air bag, mounted on the inboard side of the driver seat back. Can Specialty Vehicle Security Barriers be mounted within the side air bag deployment zones? No. The side air bags inflate extremely fast because of the nature of side crashes to the vehicle. Mounting a security barrier behind the front seats with the ends placed within the side air bag deployment zones will result in unintended interaction between the barrier and the inflating side air bags. To reduce the risk of injury to the vehicle occupants, GM recommends that the side air bag zones be kept free of any customer installed equipment. Customer furnished equipment installed to the vehicle roof. Your police vehicle is designed with an interior roof cover system which includes internal components for the interior lamps and wiring. The roof system may also include side air bag components. Inflation devices may be mounted on the vehicle roof side behind the rear doors as well as air bag tethers retained to the windshield pillars. Care must be taken to avoid damage to these components or interference with their operation when installing roof mounted equipment such as emergency lamps and communication antennas. Recommended GM service procedures must be followed to remove and re-install the instrument panel top pad to ensure that the top pad will release properly in the event of a passenger air bag deployment. On the right half of the top pad closest to the passenger air bag module, GM recommends that no equipment be mounted. When mounting equipment on the driver side of the top pad, GM recommends that the total mass of the top pad mounted special equipment not exceed 8 pounds (3.6 kilograms), since some top pads tend to rotate about the left end. Fasteners used to secure special equipment to the instrument panel top pad, the windshield glass, or to the windshield upper frame (header), should be selected to ensure that these devices will remain attached during a vehicle crash and possible air bag deployment.

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

AIR BAG FAQ | 23 Can the installation of push bumpers on the front end of the vehicle affect the deployment of the air bag?

I've heard that a deployed air bag produces whet appears to be smoke, is the air bag hot?

General Motors is not aware of adverse effects during crash events from the many push bumpers thai have been installed on GM police vehicles. Because there are many styles of push bumpers available with varying crash characteristics, installation of push bumpers may or may not affect deployment timing of the air bags. Push bumpers should be mounted to avoid modifying the vehicle structure and interfering with the front air bag sensors mounted on the upper radiator support cross member

After the bag has deployed in a crash, the air bag itself will not be hot to touch. Some components within the air bag module will be hot for a short time. A small amount of smoke coming from a deployed air bag module is normal and should not be cause for concern.

Two front impact sensors are installed in General Motors vehicles. Do not relocate or disconnect the front sensors. The location and orientation of the front sensors are critical for correct operation of the air bag system. Avoid mounting components on or near the sensors. Push bumper styles with vertical pushing members that are in foreaft alignment with the front air bag sensors are not recommended. When should an air bag inflate? The driver's and right-front passenger's frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system's designed "threshold level." In addition, your vehicle has “dual stage” frontal air bags which tailor the the amount of restraint according to crash severity. For moderate frontal impacts, the air bags inflate at a level less than full deployment. For more severe frontal impacts, "dual stage" frontal air bags deploy at full levels. If the front of your vehicle goes straight into a wall that doesn't move or deform, the threshold level of the reduced deployment is about 12 to 16mph (19 to 15 km/h), and the threshold level for a full deployment is about 18 to 24 mph (29 to 28.5 km/h). The threshold level can vary, however, with specific vehicle design, so that it can be somewhat above or below this range. If your vehicle strikes something that will move or deform such as a parked car, the threshold level will be higher. The driver's and right-front passenger's frontal air bags are not designed to inflate in rollover, side impacts, or rear impacts, because inflation would not help the occupant. Seat mounted side impact air bags are designed to inflate in moderate to severe side crashes. The side impact air bags will inflate if the crash severity is above the designed "threshold level." The threshold level can vary with specific vehicles design. The side impact air bags are not designed to inflate on frontal or near-frontal impacts or rear impacts, because inflation would not help the occupant.

Also, when the nitrogen gas is vented out of the air bag, small particles from inside the bag are also vented into passenger compartment. These airborne particles look like smoke and some particles are deposited as residue on and around the air bag. I've heard that the dusts that are released into the passenger compartment from the air bag are harmful, is this true? For most people, the only effect the dusts will produce is some irritation of the throat and eyes, and that is only if the occupant remains in the vehicle for many minutes after the air bag deployment with no ventilation and windows closed. However, some people with asthma may develop an asthmatic attack from inhaling the dusts. If this happens, they should first treat themselves the same way their doctor has advised them to treat any other asthma attack, and then immediately seek medical treatment. Can the air bag system be re-used? No, The air bags are designed to inflate only once. After inflation some new parts will be required. These will include the air bag module and possibly other parts. (A competent service technician with access to the vehicle's service manual and the required tools should replace the required components after a deployment crash.) If my vehicle has air bags, why should I have to wear my safety belt? Air bags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts not instead of them. Every air bag system ever offered for sale has required the use of safety belts. Even if you're in a vehicle that has air bags, you still have to buckle up to get the most protection. That's true not only in frontal collisions but especially in side and other collisions.

Roof rail mounted head-curtain air bags are designed to inflate in moderate to severe side crashes. In addition, certain vehicles have head-curtain air bags which are also designed to inflate in situations where an impending rollover condition is identified by the vehicle's rollover sensing system and/or frontal or near-frontal impacts if the crash severity is above the designed "threshold level". Safety belt pretensioners at the driver and front passenger seat positions are designed to deploy in frontal, near-frontal, side, and rear crashes that exceed the "threshold level" of crash severity to help reduce slack in the safety belt Safety belt pretensioners will also deploy in impending rollover situations. How long will the air bag remain inflated? It takes approximately 1/20th of a second to fully inflate the frontal air bags. This is faster than the blink of an eye. The air bags begin to deflate immediately, helping to stop the occupants more gradually.

2014 Chevrolet Municipal Vehicles Technical Manual

24 | AIR

BAG FAQ A H

ARMREST ARMREST

200 mm (7.9 in.)

500 mm (19.7 in.)

C

B

D

F

E

G

Standard Head Curtain and front Seat-Mounted Side IMpact Air bag1 Deployment Zones Passenger Side Shown, Driver Side Similar

E. Front seat thorax-pelvic air bag zone F.  Back edge of body center pillar trim at bottom of rear door window G.  Rear-most end of front head curtain H.  Zone extends into sail panel area

A.  Head Curtain air bag zone – front seats only B.  Front door sill C. Front door armrest D.  Fore-most end of seat-mounted thorax air bag zone A

G

ARMREST ARMREST

B

500 mm (19.7 in.)

C D

E

F

OPtional (RPO AYG) Head Curtain and front Seat-Mounted Side IMpact Air bag1 Deployment Zones Passenger Side Shown, Driver Side Similar

A.  Head Curtain air bag zone – front and rear seats B.  Front door sill C. Front door armrest D.  Fore-most end of seat-mounted thorax air bag zone

E. Front seat thorax air bag zone F.  Back edge of body center pillar trim at bottom of rear door window G.  Zone extends into sail panel area

1. Head curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 - AIR BAGS | 25 D

127 mm (5 in.)

A

B

C

127 mm (5 in.)

E F G H I J K L 200 mm (7.8 in.)

200 mm (7.8 in.)

Head Curtain and front Seat-Mounted Side IMpact Air bag1 Deployment Zones View from Rear seat, Right side is mirror of left side

A.  Vehicle center-line B.  Headrest C.  Center-line of occupant D. Edge of headliner E. Door inner trim panel F.  Center body pillar trim

N

A

B

C



G.  Head curtain air bag zone H.  Bottom of door windows I.  Front door handle J.  Front seat back thorax-pelvic air bag zone K.  Seat back L.  Door sill

O M

D

L

E

K

F 130 mm (5.1 in.)

130 mm (5.1 in.) 680 mm (25.7 in.) 625 mm (24.6 in.)

G H

470 mm (185 in.)

420 mm (16.5 in.) 150 mm (5.9 in.)

J I

Instrument panel and approximate deployment area of the driver and front passenger air bags1 View from top

A.  Vehicle center-line B.  Driver center-line C.  Front of instrument panel at the windshield base D. Driver door trim E. Driver knee air bag



F.  Instrument cluster G.  Rear-most instrument panel H.  Steering wheel I.  Driver air bag J.  Front passenger air bag



K.  Glove box L.  Front passenger knee air bag M.  Front passenger door trim N.  Front passenger center-line O.  Radio stack

1. H  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

26 | CAPRICE

Police Package 9C1 - AIR BAGS Side view of Driver steering wheel air bag1 deployment zone – Center-line of driver

A

880 mm (26.7 in.)

View from Right Side B

C

A.  Rear most instrument panel B.  Top of windshield C.  Driver air bag zone D. Driver air bag E. Driver seat F.  Driver knee air bag G.  Instrument cluster

G

D

F 130 mm (5.1 in.)

E

130 mm (5.1 in.)

A

880 mm (26.7 in.)

Side view of Front seat passenger air bag1 deployment zone – Center-line of passenger View from Right Side

B C

G

D



A.  Rear-most instrument panel B.  Top of windshield C.  Front passenger air bag zone D. Front passenger air bag E. Front passenger seat F.  Front passenger knee air bag G.  Glove box door

F 130 mm (5.1 in.)

E

130 mm (5.1 in.)

1. Head curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

CAPRICE Police Package 9C1 - AIR BAGS | 27 GM offers Anti-Lock Brake Systems as standard or optional on all North American passenger vehicles and light truck lines. The computerized Anti-Lock Braking System (ABS) is designed to keep the vehicle’s wheels rotating as the brakes are applied to assist the driver in achieving a controlled stop. Sensors monitor how fast the wheels rotate and feed the data continuously to the ABS computer. The vehicle’s brakes slow each wheel as the brake pedal is applied. However, when ABS is activated due to road conditions, the system repeatedly releases and applies pressure to the brakes. The wheels can keep rolling, thus retaining steering ability and enhanced stability while providing a higher braking force on most surfaces than a locked wheel provides. How exactly does ABS work? In cars without ABS, hitting the brakes can cause the wheels to lock, leaving you unable to steer the vehicle until you decrease the pressure so the wheels can roll again. With an ABS, as you apply the brakes, the ABS computer monitors the wheel speed sensor information. If the computer senses that a wheel is approaching lock up, it sends a signal to the hydraulic modulator to reduce, then to reapply, brake pressure several times a second for as long as you maintain firm pressure on the brake pedal. The process is much like the threshold braking technique used with conventional brakes. However, ABS does it much faster and more accurately than any driver can, leaving you free to focus on steering away from obstacles.

Does ABS reduce stopping distances?

Should I drive an ABS equipped vehicle differently than I would drive a vehicle with conventional brakes? Most of the time, under normal driving circumstances, there is no difference, and you should always drive with the same caution and care. It is important to realize that ABS only makes a difference when it is activated—when you have to brake hard—and that would only be when the computer senses that a wheel is approaching lock up. When ABS activates, keep steady pressure on the brake pedal and then let the ABS work for you. Don’t pump the brakes or try to ­find the threshold. Simply hold the brake pedal down and steer if necessary to avoid an obstacle.

Is ABS always active? ABS is always available, but not always activated. ABS is activated only when the brake pedal is applied and the computer detects an impending wheel lock condition.

Can older cars be retrofitted with ABS? No! The brake system is one of the most important features on any passenger vehicle. Several products, which tap into the master cylinder and/or brake system performance, are being sold in the aftermarket. Some of these products imply performance similar to new vehicle anti-lock brake systems. However, contrary to their claims, add-on systems, which deplete fluid from the master cylinder on brake apply may actually increase a vehicle’s stopping distance. This may cause the vehicle to fail to comply with Federal brake standards.

Does ABS always activate at the same speed? No, the system operates when the computer detects wheel lockup, at any speed above 8 mph.

Yes, in braking situations where the wheels on a non-ABS equipped vehicle would lock up, ABS will generally provide shorter controlled stopping distance. The amount of improvement in stopping distance depends on many factors, including the road surface, severity of braking, initial vehicle speed, etc. On some surfaces, such as gravel roads, braking distances can be longer, but you will still have the control benefits of ABS. The important capability of ABS is control. ABS provides improved vehicle steerability and stability when braking.

Will ABS wear out a vehicle’s brakes sooner?

What can affect the ABS advantage?

Do Federal Safety Standards mandate ABS?

It is important that you follow the maintenance schedule recommended in the owner’s manual of the vehicle, tires should be at their proper inflation level, the brake pads should be checked regularly, etc. While driving, you should sit comfortably, so that your hips are back in the seat and your knees are bent, even while braking. Your foot should be positioned so that your heel is on the floor and your toes are secure on the lower half of the pedal. And, though ABS may reduce stopping distance, remember: The faster you go, the longer it takes you to stop. Keeping a safe distance between you and the vehicle in front of you is always necessary, even with ABS.

A properly maintained brake system will be unaffected by ABS operation under typical driving conditions.

Are there different types of ABS? Yes, there are rear wheel anti-lock systems (RWAL) used on some trucks and four-wheel ABS available on cars and trucks.

No. Federal standards establish minimum braking performance requirements that all vehicles must meet, but do not specify how they should be met. It should be noted that even a vehicle with failed ABS meets the Federal safety standard for stopping distances.

Will a tire size change affect ABS? Use of tires other than original equipment may affect ABS performance. Owners should consult and follow the recommendations contained in the vehicle owner’s manual regarding replacement tire size. NOTE: ABS will work with original equipment spare tire or tire

What happens if ABS becomes inactive?

chains. However, performance is reduced.

The ABS electronic control unit has on-board diagnostic capability. If a fault is detected, the vehicle will revert to the base brake system, and the ABS telltale on the dash will be illuminated. Should this happen, the vehicle should be taken to a dealership for repair as soon as possible.

Do insurance companies give a discount for ABS?

How do I use ABS? Depress and hold the pedal. DO NOT PUMP THE BRAKES (that prevents the system from working). Just hold the brake pedal down and let the ABS work for you. You may feel the brake pedal vibrate, or you may notice some noise, but this is normal as the system works for you.

Yes, many insurance companies give discounts that range from 5% to 10%. In the states of New York and Florida all insurance companies are required to give an ABS discount of 5% on certain coverages such as bodily injury, property damage, collision, and personal injury protection. In other states the discount varies from insurance company to insurance company. When buying auto insurance, always ask your insurance agent if his/her company gives a discount for vehicles equipped with antilock brakes.

2014 Chevrolet Municipal Vehicles Technical Manual

28 | Anti-lock

braking system

IMPORTANT DRIVING SAFETY TIPS A. A lways maintain a safe

following distance. ABS does not

allow you to stop on a dime. (Generally a 2-second following distance is considered safe in ideal conditions.) Watch the vehicle in front of you pass a fixed marker (such as a sign). Count seconds—one-thousand-one, one-thousand-two-until your front bumper reaches the marker. If you do not count out two seconds, then you are too close to the vehicle in front of you. Also, if the roads are wet or icy, or visibility is poor, you should increase your following distance.

B. A lways drive carefully—

especially on slippery surfaces. ABS cannot create friction between the tires and the road surface, it can only give the driver the maximum advantage of the existing adhesion. If the vehicle is traveling on a surface with no adhesion, the best ABS in the world cannot provide a shorter stopping distance or good steering.

C. It is a good idea to practice an

ABS activated stop and get the feel of the brake pedal. However, please make sure it’s at a safe time with no obstacles in your path. And you only really need to try it once or twice to know what happens.

Electronic Stability Control systems (StabiliTrak) Q. How does StabiliTrak work? StabiliTrak systems help drivers maintain control of their A. StabiliTrak has the ability to apply control forces to vehicles, especially during emergency lane changes or the vehicle independent of the driver. StabiliTrak uses avoidance maneuvers. StabiliTrak uses various sensors, sensors to continuously compare the path indicated by such as steering wheel angle, wheel speed, yaw velocity, the steering wheel position to the vehicle’s actual path. If etc., to detect any difference between the path requested a discrepancy is detected, StabiliTrak selectively controls by the steering wheel position and vehicle’s actual path. vehicle brakes and engine torque to create a yaw moment When appropriate, the system selectively controls brakes, that helps restore the vehicle’s actual path to the path engine power, and even suspension settings to enhance indicated by the steering wheel position. StabiliTrak has control of the vehicle’s direction and help keep it on course. the ability to help correct both understeer (where the Independent studies conducted by the National Highway vehicle is not turning as much as the steering wheel Traffic Safety Administration, the Insurance Institute for position indicates) and oversteer (where the vehicle is Highway Safety, and others have found StabiliTrak to be turning more than the steering wheel position indicates). highly effective in reducing vehicle crashes. General Motors The illustration at right shows how selective braking at a offers StabiliTrak systems on many of its passenger car particular wheel can create a compensating yaw moment and light truck models. to help restore the vehicle’s actual path to the path See your owner's manual for additional information about indicated by the steering wheel position. the operation of StabiliTrak. Q. Will a tire change affect StabiliTrak? Q. How do I use StabiliTrak? A. Use of tires other than original equipment may affect A. S  tabiliTrak operates independently of the driver. You StabiliTrak performance. StabiliTrak is designed to make should continue to drive your StabiliTrak equipped the best use of available traction. The performance vehicle with caution and care. GM’s StabiliTrak system, characteristics of the original equipment tires are part of StabiliTrak, is designed to be as seamless as possible in the overall system effectiveness. When you replace tires operation, to be part of the overall vehicle response and to check the recommendations in your owner's manual. On make a good vehicle better GM vehicles, the original equipment tires have a “TPC” (Tire Performance Criteria) code on the sidewall. Replacing the tires with the same “TPC” code will help assure proper StabiliTrak performance.

2014 Chevrolet Municipal Vehicles Technical Manual

NOTES | 29

2014 Chevrolet Municipal Vehicles Technical Manual

30 | NOTES

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited Police Package 9C1 | 1

Shown with aftermarket equipment

Shown with aftermarket equipment

Updates for 2014

New Features

• Carry Over content with new name "Impala Limited"

Deleted

• Victory Red exterior paint (74U)

2014 Chevrolet Municipal Vehicles Technical Manual

2 | Impala

Limited Police Package 9C1

This vehicle has been designed for police work up to and including high speed emergency vehicle operations. GM restricts the sale of police vehicles and they are not to be sold to retail customers. Some standard equipment may be replaced by special equipment when the Police Package 9C1 is ordered

MODEL AVAILABILITY

1ws19

Front-wheel drive

Warranty

3 years / 36,000 mile bumper-to-bumper (whichever comes first, see dealer for details) 5 years / 100,000 mile limited powertrain (whichever comes first, see dealer for details)

STANDARD EQUIPMENT SUMMARY INTERIOR FEATURES

AIR CONDITIONING Single-zone manual, with air filtration and environmentally friendly refrigerant r134a Bluetooth Not available Cruise Control Electronic with set and resume speed Cup Holder Cup holder with storage tray between seats DOME Lamps Auxiliary, interior, sustained illumination. Floor Covering Carpeting front and rear (carpeted mats are available; see option b34 on page 9) GLASS Tinted windshield, backlight and side glass GLove box Non-locking without light MIRRORS, VISOR Visor, left hand and right hand with covered vanity mirrors MIRROR, REARVIEW Inside rearview is manual day night with driver and passenger map lamps Navigation System Not available OnStar Not available RADIO Electronically tuned am/fm stereo with cd player, seek-scan, digital clock, auto-tone control, theftlock with integrated rear window antenna (radio delete is not available) RESTRAINT SYSTEM Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, dual head curtain air bags1 for front and rear outboard occupants and front seat back mounted thorax-pelvic air bags1 SEAT, FRONT High density foam cloth bucket seats with seat back security panel, 6-way power driver and passenger seat adjusters (see page 4) and manual reclining seat backs. Driver seat has manual lumbar control. Front seat frames are strengthened for side impact resistance (see page 17) SEAT, REAR Vinyl bench with high density foam non-folding seat back (see page 4) SMOKER'S PACKAGE Not available SPEEDOMETER/Cluster 140 mph certified analog speedometer, 5 mph increments with digital trip odometer and warning lamps. Driver Information Center includes 1 mph redundant digital speed display (see message center listing on page 15) STEALTH MODE See exterior lamps control on page 17 for operation description STEERING WHEEL Tilt-wheel with column mounted gear shift lever Theft Deterrent System Vehicle PASS-Key® III+, content theft deterrent is disabled (to enable content theft deterrent option ua6 must be ordered) Trunk mat Heavy-duty (see page 17) WARNING LAMPS Brake, safety belt, air bag1, anti-lock brake, check engine (see page 14 for additional information) Warning Tones Key-in-ignition, driver door open, driver and passenger safety belt not buckled, headlamps on WINDOW OPERATION Power with driver express down, rear window lockout switch

Auxiliary Power, Front

Electrical Features

1 00-amp ignition and main power supply wiring under lower right side of instrument panel (see wiring provisions for 12-volt battery power supply on page 16) Auxiliary Power, Trunk 100-amp auxiliary power outlet in trunk (see page 16) Ground Stud Auxiliary, located in trunk (see page 16) LOCK-OUT PROTECTION Not available, driver door can be locked with the key in the ignition. Lock-out protection feature cannot be activated POWER OUTLETS 2 auxiliary power outlets for additional plug-in equipment located on lower center of instrument panel Wiring Diagrams See pages 23 through 25 for description; also see Impala Police Package owner’s manual supplement (located in glove box folder with standard owner’s manual) Wiring Provision, EXTerior Lamps Flashing Forward lamp harness in-line connector for Exterior Lamp Flashing System (see option 6j7 on page 9)

1. Head curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited Police Package 9C1 | 3 EXTERIOR FEATURES

Body Panels Two-sided galvanized steel for all exterior body panels (except roof where not needed) Body Side Moldings Optional (See option B86 on page 9) DEFOGGER Electric, rear window DOOR LOCKS Power non-programmable (automatic door locking and unlocking feature is disabled), child safety locks in rear doors. Driver door lock key cylinder only; key lock cylinder is not available in the front passenger door Headlamps Dual halogen composite, includes flash-to-pass feature and automatic lamps control with daytime running lamps (to delete automatic control, see option 9G8 on page 9 and exterior lamps control on page 17) HORNS Dual note Keyless Entry Includes two transmitters with non-functional panic button; the keyless entry system used on the police Impala includes a stealth mode feature. When the “unlock” or “lock” button is depressed, no exterior lamps or audible sounds are activated; however, the interior OEM dome lamp will illuminate unless option 7Y6 lamps, Inoperative Dome and Courtesy Lamps is ordered; during remote start feature, running lamps will remain illuminated (additional transmitters are available; see option AMF on page 9) Keys Two-sided, random code, for ignition, driver door and trunk only; single key locking system to operate entire fleet is available (fleet coded single key is available; see 6E2 and 6E8 option on page 9) License Plate Mounting hardware located in glove box; front bracket standard in states requiring front license plates; others must order option vk3 MIRRORS, Rearview Body color, electric Left hand and right hand remote (heated mirrors are available; see option DK2 on page 9) PAINT Base coat/clear coat TRUNK LAMP Standard TRUNK RELEASE Electric, ignition controlled, button located on left side of instrument panel, (ignition control release is available; see option a98 on page 9) UNDER HOOD LAMP Not available WINDSHIELD WIPERS Intermittent, anti-lift with washer

CHASSIS FEATURES

Alternator 170-amp with idle boost (transmission in park or neutral) controlled by battery energy level sensing Battery 720 CCA 70-amp hour with battery rundown protection (does not protect customer installed equipment) BODY Body frame intergal (unibody) Heavy-duty reinforced body components BRAKES 4-wheel anti-lock disc brakes with police calibration and heavy-duty front brake pads COOLING Heavy-duty (high capacity) with 225-watt fans and extended life coolant; coolant hoses are EPDM (ethylene-propylene-diene monomer) rubber; silicone hoses are not required (coolant is DEX-COOL good for 5 years/150,000 miles, protects from -34° F to +265° F and against rust and corrosion) (see also page 17) Chassis Lubrication Lubed-for-life chassis ENGINE 3.6L V6 DOHC SIDI (spark ignited direct injection) engine with with Variable Valve Timing (VVT) with FlexFuel2 (gas or E85 ethanol); includes wide open throttle air conditioning cut off (when overhead lamps, spotlamps, radio antennas, sirens, and other emergency equipment are installed, overall performance may be reduced) EXHAUST SYSTEM Stainless steel, single with dual outlets FUEL TANK capacity 17 gallon (64 liters) Oil Coolers Engine, transmission and power steering oil coolers: external air-to-oil (see page 17) Radio Suppression Extended life - iridium tip spark plugs and wires that are designed to reduce radio frequency noise levels which may affect communications equipment including operating frequencies in the 38-MHz to 58-MHz range. The Impala is designed with unibody construction, and multiple grounding points are provided for the vehicle electrical system. No additional ground straps are added for the Police Package StabiliTrak Stability enhancement system. An advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. Each time the vehicle is started, the StabiliTrak system is fully on. StabliliTrak can be controlled by a StabiliTrak button on the instrument panel located below the dimmer control on the headlamp switch (see page 17). The condition of the system is displayed by an instrument panel StabiliTrak indicator light and Driver Information Center (DIC) Messages. Push once, Performance Mode is active and Traction Control is off, push and hold five seconds Traction Control and StabiliTrak are off, push again and Traction Control and StabiliTrak are turned back on Starter Interrupt Prevents starter from engaging while the engine is running STEERING Power, rack and pinion Struts, Front Heavy-duty SUSPENSION 4-wheel independent, firm ride and handling with increased ride height springs, heavy-duty front and rear stabilizer bars TIRES Goodyear P235/55R17 SBR blackwall, “W” rated with compact spare (full-size spare is available; see option RUF on page 9) TIRE PRESSURE MONITOR Check Tire Pressure will show on driver message center (see page 17 for description) Traction control Deactivated when Police Performance Mode is engaged TRANSMISSION 6-speed automatic, electronically-controlled transmission provides protection against over-revving the engine in low gear and a mechanical low gear blockout is not required; if a driver manually selects low gear and fails to manually upshift to high gear, the powertrain control module automatically protects the drivetrain. It can be manually shifted up and down with buttons located on steering wheel WHEELS 17" x 7.5" heavy-duty steel WHEEL Center Cap Chrome bolt-on metal 2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited Police Package 9C1

4|

POWERTRAIN

ENGINE

OPTION

TYPE

TRANSMISSION

DISPLACEMENT

CODE LITERS/CU. IN. LFX V6 3.6/217

EMISSIONS -

FUEL

OPTION

AXLE

TYPE

OPTION

RATIO

SYSTEM CODE CODE 6T70 FlexFuel2 (gas or E85 MXO 6-speed F71 ethanol) auto. with OD

2.44

MUST BE SPECIFIED

FE9

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State YF5 California emissions. Use for ordering vehicles that will be registered in California. NE1 CT/ME/MD/MA/NJ/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8 Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Delaware, Massachusetts, Maryland, New Jersey, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State. NC7 Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/DE/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles” NB9 Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California. NOTE: T he 2014 Chevrolet Impala Police Patrol Vehicle with the 3.6L Engine (LFX) with Emission Option Codes FE9, NE1, and YF5 is certified to EPA Tier 2 Bin 4 standards and qualifies as ULEV (Ultra Low Emission Vehicle) under California Air Resources Board (CARB) requirements, meaning it is 50-state certified. Emission Standard: BIN4 EPA engine family or test group: EGMXJ03.6166

TIRES -

SPEED RATED



MANUFACTURER

QUANTITY

SIZE

SPEED RATING

TYPE



Goodyear

Four

P235/55R17 SBR blackwall

W

All Season BW

NOTE: • Compact spare is standard (full-size spare is available see option RUF on page 9)  • Due to specific requirements for performance, durability and safety, gm recommends only the original equipment tire for replacement • Tire Plys = Tread: 2 Polyester, 2 Steel, 1 Nylon Sidewall: 2 Polyster Total 7 Ply • Do not use tire chains - See your Owner's Manual for more information.

SEATS AND INTERIOR TRIM



STANDARD OPTIONAL

SEAT OPTIONS

EBONY

AR9

19G

AR9

19E

Front: Cloth buckets (power driver and passenger) Rear: Vinyl bench (non-folding seat back) Front: Cloth buckets (power driver and passenger) Rear: Cloth bench (non-folding seat back)

AVAILABLE EXTERIOR COLORS 17U

41U

50U

GLJ

Silver Ice Metallic

Black

Summit White

Ashen Gray Metallic

NOTE: For special paint and paint schemes see page 12 through 14



Actual colors may vary

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited Undercover Police PKG 9c3 | 5

Updates for 2013

Shown with optional rear spoiler

Updates for 2014

New Features • Carry Over

Deleted

• Victory Red exterior paint (74U)

2014 Chevrolet Municipal Vehicles Technical Manual

6 | Impala

Limited Undercover Police PKG 9c3

This vehicle has been designed for police work up to and including high speed emergency vehicle operations. GM restricts the sale of police vehicles and they are not to be sold to retail customers. Some standard equipment may be replaced by special equipment when the Police Package 9C1 is ordered

MODEL AVAILABILITY

1ws19

Front-wheel drive

Warranty

3 years / 36,000 mile bumper-to-bumper (whichever comes first, see dealer for details) 5 years / 100,000 mile limited powertrain (whichever comes first, see dealer for details)

STANDARD EQUIPMENT SUMMARY INTERIOR FEATURES Air conditioning Single-zone manual, with air filtration and environmentally friendly refrigerant r134a Bluetooth Not available Cruise control Electronic with set and resume speed Floor covering Carpeting front and rear (carpeted mats are available; see option b34 on page 9) Dome Lamps Auxiliary, interior, sustained illumination Glass Tinted, windshield, backlight and side glass GLove box Non-locking without light Mirrors, visor Visor, left hand and right hand with covered vanity mirrors Mirror, rearview Inside rearview is manual day night with driver and passenger map lamps Navigation System Not available OnStar Not available Radio Electronically tuned am/fm stereo with cd player, seek-scan, digital clock, auto-tone control, theftlock with integrated rear window antenna (radio delete is not available) RESTRAINT SYSTEM Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, dual head curtain air bags1 for front and rear outboard occupants and front seat back mounted thoraxpelvic air bags1 Seat, front 40/20/40 splint-bench cloth seat with folding arm rest and cup holder, 6-way power driver seat with recliner and manual lumbar, 6-way power passenger seat with manual reclining seat back and strengthened front seat frames for side impact resistance (see page 17) Seat, rear Cloth bench with high density foam non-folding seat back (see page 8) Smoker's package Not available Speedometer/cluster 140 mph certified analog speedometer, 5 mph increments with digital trip odometer and warning lamps. Driver Information Center includes 1 mph redundant digital speed display (see message center listing on page 15) STEALTH MODE See exterior lamps control on page 17 for operation description Steering wheel Tilt-wheel with column mounted gear shift lever Theft deterrent System Vehicle PASS-Key® III+, content theft deterrent is disabled (to enable content theft deterrent option UA6 must be ordered) Trunk mat Heavy-duty (see page 17)­­­­ Warning LAMPS Brake, safety belt, air bag1, anti-lock brake and check engine (see page 15 for additional information) Warning Tones Key-in-ignition, driver door open, driver and passenger safety belt not buckled, headlamps on Window Operation Power with driver express down, rear window lockout switch

Electrical features Auxiliary power, front

1 00-amp ignition and main power supply wiring under lower right side of instrument panel (see wiring provisions for 12-volt battery power supply on page 16) Auxiliary power, trunk 100-amp auxiliary power outlet in trunk (see page 16) Ground stud Auxiliary, located in trunk (see page 16) LOCK-OUT PROTECTION Not available, driver door can be locked with the key in the ignition. Lock-out protection feature cannot be activated Power outlets 2 auxiliary power outlets for additional plug-in-equipment located on lower center of instrument panel Wiring diagrams See pages 23 through 25 for description; also see Impala Police Package owner’s manual supplement (located in glove box folder with standard owner’s manual) Wiring Provision, EXTerior Lamps Flashing Forward lamp harness in-line connector for Exterior Lamp Flashing System (see option 6j7 on page 9)

1. Head curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited Undercover Police PKG 9c3 | 7 EXTERIOR FEATURES Body panels Two-sided galvanized steel for all exterior body panels (except roof where it is not needed) Body Side Moldings Optional (See option B86 on page 9) Defogger Electric, rear window DOOR LOCKS Power non-programmable (automatic door locking and unlocking feature is disabled), child safety locks in rear doors. Driver door lock key cylinder only; key lock cylinder is not available in the front passenger door Headlamps Dual halogen composite, includes flash-to-pass feature and automatic lamp control with daytime running lamps (to delete automatic control, see option 9g8 on page 9 and exterior lamps control on page 17) Horns Dual note Keyless entry Includes two transmitters with non-functional panic button; the keyless entry system used on the police Impala includes a stealth mode feature. When the “unlock” or “lock” button is depressed, no exterior lamps or audible sounds are activated; however, the interior OEM dome lamp will illuminate unless option 7Y6 lamps, Inoperative Dome and Courtesy Lamps is ordered; during remote start feature, running lamps will remain illuminated (additional transmitters are available; see option AMF on page 9) Keys Two-sided, random code, for ignition, driver door and trunk only; single key locking system to operate entire fleet is available (fleet coded single key is available; see option 6e2 and 6e8 on page 9) License plate Mounting hardware located in glove box; front bracket standard in states requiring front license plates; others must order option vk3 Mirrors, rearview Body color, electric left hand and right hand remote (heater mirrors are available; see option dk2 on page 9) Paint Base coat/clear coat TRUNK LAMP Standard Trunk release Electric (not ignition controlled), button located on instrument panel, left of steering column; manual inside trunk safety release (ignition control is available; see option A98 on page 9) UNDER HOOD LAMP Not available Windshield wipers Intermittent, anti-lift with washer

Chassis features Alternator Battery Body Brakes Cooling

1 70-amp with idle boost (transmission in park or neutral) controlled by battery energy level sensing 720 CCA 70-amp hour with battery rundown protection (does not protect customer installed equipment) Body frame inergal (unibody) Heavy-duty reinforced body components Power 4-wheel anti-lock disc brakes with police calibration and heavy-duty front brake pads Heavy-duty (high capacity) with 225-watt fans and extended life coolant; coolant hoses are EPDM (ethylene-propylene-diene monomer) rubber; silicone hoses are not required (coolant is DEX-COOL good for 5 years/150,000 miles, protects from -34° F to +265° F and against rust and corrosion) (see also page 17) Chassis lubrication Lubed-for-life chassis ENGINE 3.6L V6 DOHC SIDI (spark ignited direct injection) engine with with Variable Valve Timing (VVT) with FlexFuel2 (gas or E85 ethanol); includes wide open throttle air conditioning cut off (when overhead lamps, spotlamps, radio antennas, sirens, and other emergency equipment are installed, overall performance may be reduced) Exhaust system Stainless steel, single with dual outlets Fuel tank capacity 17 gallon (64 liters) Oil coolers Engine, transmission and power steering oil coolers: external air-to-oil (see page 17) Radio suppression Extended life - iridium tip spark plugs and wires that are designed to reduce radio frequency noise levels which may affect communications equipment including operating frequencies in the 38-MHz to 58-MHz range. The Impala is designed with unibody construction, and multiple grounding points are provided for the vehicle electrical system. No additional ground straps are added for the Police Package StabiliTrak Stability enhancement system. An advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. Each time the vehicle is started, the StabiliTrak system is fully on. StabliliTrak can be controlled by a StabiliTrak button on the instrument panel located below the dimmer control on the headlamp switch (see page 17). The condition of the system is displayed by an instrument panel StabiliTrak indicator light and Driver Information Center (DIC) Messages. Push once, Performance Mode is active and Traction Control is off, push and hold five seconds Traction Control and StabiliTrak are off, push again and Traction Control and StabiliTrak are turned back on Starter interrupt Prevents starter from engaging while the engine is running Steering Power, rack and pinion­­­­ Struts, front Heavy-duty Suspension 4-wheel independent, firm ride and handling with increased ride height springs, heavy-duty front and rear stabilizer bars Tires Goodyear P235/55R17 SBR blackwall, “W” rated with compact spare (full-size spare is available; see option RUF on page 9) Tire pressure monitor check tire pressure will show on driver message center (see page 17 for description) Traction control Deactivated when Police Performance Mode is engaged Transmission 6-speed automatic, electronically-controlled transmission provides protection against over-revving the engine in low gear and a mechanical low gear blockout is not required; if a driver manually selects low gear and fails to manually upshift to high gear, the powertrain control module automatically protects the drivetrain. It can be manually shifted up and down with buttons located on steering wheel Wheels 17" x 7.5" heavy-duty steel Wheel covers Full-size plastic wheel covers 2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

8 | Impala

Limited Undercover Police PKG 9c3

POWERTRAIN

ENGINE

OPTION

TYPE

TRANSMISSION

DISPLACEMENT

CODE LITERS/CU. IN. LFX V6 3.6/217

EMISSIONS -

FUEL

OPTION

AXLE

TYPE

OPTION

RATIO

SYSTEM CODE CODE 6T70 FlexFuel2 (gas or E85 MXO 6-speed F71 ethanol) auto. with OD

2.44

MUST BE SPECIFIED

FE9

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State

YF5

California emissions. Use for ordering vehicles that will be registered in California.

NE1 CT/ME/MD/MA/NJ/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8

Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Massachusetts, Maryland, New Jersey, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State.

NC7

Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles”

NB9

Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California.

NOTE: T he 2013 Chevrolet Impala Police Patrol Vehicle with the 3.6L Engine (LFX) with Emission Option Codes FE9, NE1, and YF5 is certified to EPA Tier 2 Bin 4 standards and qualifies as ULEV (Ultra Low Emission Vehicle) under California Air Resources Board (CARB) requirements, meaning it is 50-state certified. Emission Standard: BIN4 EPA engine family or test group: DGMXJ03.6166

TIRES -

SPEED RATED



MANUFACTURER

QUANTITY

SIZE

SPEED RATING

TYPE



Goodyear

4

P235/55R17 SBR blackwall

W

All Season BW

NOTE: • Compact spare is standard (full-size spare is available see option RUF on page 9)  • Due to specific requirements for performance, durability and safety, gm recommends only the original equipment tire for replacement • Tire Plys = Tread: 2 Polyester, 2 Steel, 1 Nylon Sidewall: 2 Polyster Total 7 Ply • Do not use tire chains - See your Owner's Manual for more information.

SEATS AND INTERIOR TRIM



SEAT OPTIONS

EBONY

AN3

19C

STANDARD Front Cloth 40/20/40 split-bench Rear: Cloth full bench (non-folding seat back)

AVAILABLE EXTERIOR COLORS 17U

41U

50U

GLJ

Silver Ice Metallic

Black

Summit White

Ashen Gray Metallic

NOTE: For special paint and paint schemes see page 12 through 14



2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

Actual colors may vary

Impala Limited 9c1 & 9c3 - Options | 9 body side moldings - Body-color (installed on all 4 doors) CONTENT theft deterrent ALARM system - Requires ap3 remote start, unauthorized entry sounds horn and lamps flash delete daytime running lamps and automatic headlamps - Exterior lamps are operated manually (see page 17) flasher system, headlamps and tail lamps - drl compatible, headlamp flasher module with control wire and body control module rear lamp flashing (see page 19 for description) 6a3 Floor covering - Heavy-duty vinyl replaces production carpeting; carpeted mats not available (see page 22 for description) K05 heater - Engine block 6B7 hole in roof - On center line requires 6f5 wiring (not available with 6j5 hole) (see page 20 for description) 6J5 hole in roof - On passenger side requires 6f5 wiring (not available with 6b7 hole) (see page 20 for description) AMF Keyless entry transmitters - Fleet Package includes 6 additional transmitters. Transmitters are not programmed. Each transmitter, including the two standard with the vehicle, must be programmed together by a dealer at customer expense. Transmitter programming is not a warranty item. See you owner's manual supplement for programming information. (see also page 20 for customer programming of transmitters using the vehicles Driver Information Center procedure) NOTE: Vehicle specific, common fleet transmitter frequency not available 6e2 key common - Complete vehicle fleet, provides a single key with a specific code that is common to the door locks and ignition of all the vehicles in the vehicle fleet; key code is an alternate to SEO 6e8 key common, complete vehicle fleet; not compatible with 2005 and earlier Impalas, 2006 and earlier Tahoes and 2011 Caprice 6e8 key common - Complete vehicle fleet, provides a single key with a specific code that is common to the door locks and ignition of all the vehicles in the vehicle fleet; key code is an alternate to SEO 6e2 key common, complete vehicle fleet; not compatible with 2005 and earlier Impalas and 2006 and earlier Tahoes and 2011 Caprice 6C7 lamp - Red and white front auxiliary dome, separately switched (see page 18 for description) 7y6 lamp - Inoperative Dome and Courtesy Lamps (see page 18 for description) 6J6 lamps - Rear window auxiliary stop/turn signals (see page 19 for description) T53 lamps - Altern­­­­­ate flashing trunk lid warning (see page 19 for description) VK3 license plate bracket - Front (bracket standard for states requiring front license plate) ­­B34 mats - Carpeted front and rear (not available with 6a3) DK2 mirrors - Heated outside rearview, power, body color 6N6 Rear door locks inoperative - Rear power locks are inoperable at rear doors but operate form drivers position (see page 22 for description) 6B2 Rear door handles inoperative - Doors can be opened only from outside (see page 22 for description) 6n5 rear window switches inoperative - Rear door windows only operate from driver’s position (see page 22 for description) D81 rear spoiler AP3 remote vehicle starter system - Includes remote keyless entry (required with option UA6) 7X6 spotlamp - Left hand, separately fused (see page 20 for description) 7X7 spotlamps - Left and right hand, separately fused (see page 20 for description) 7X8 spotlamp provision - Left hand (see page 20 for description) 7X9 spotlamp provision - Left and right hand (see page 20 for description) RUF tire, spare - Full-size, includes non-programed Tire Pressure Monitor (see page 18 for description) A98 trunk release - Ignition controlled 6c8 wiring - Coaxial radio antenna cable - rg58 roof to trunk (see page 18) Wx7 wiring - For customer connection to front door and windshield pillar speakers. Speakers are not connected to the vehicle radio; radio audio signals are routed to the rear speakers (see page 21 for description) 6j3 wiring - For grille lamps and speaker (see page 21 for description) 6J4 wiring - For horn/siren circuit, in-line connection for customer furnished switch (see page 21 for description) 6f5 wiring - Roof wires, requires 6b7 or 6j5 hole in roof, 2 number 10 awg wires only (see page 20 for description) Autonet Mobile WiFi in-car router - Available through your GM Dealer (see page 18 for Description)

B86 UA6 9g8 6J7

For standard and optional illustrations, see pages 15 through 22. NOTE: Ship-through charge is included as part of base MSRP.

2014 Chevrolet Municipal Vehicles Technical Manual

10 | Impala

Limited 9c1 & 9c3 Police PKG - Specs

GENERAL

ENGINE

Model Drive

1WS19 2-wheel front

EXTERIOR (in./mm) Wheelbase Overall length Overall width Overall height* Front track width Rear track width Turning diameter curb to curb (ft./m) Ground clearance* (lower control arm bolt)

110.5/2807 200.4­­/5090 72.9/1852 58.7/1491 62.4/1585 61.5/1562 38.0/11.6 6.46/164

Head room Shoulder room Hip room Leg room

39.4/1001 58.7/1491 56.4/1433 42.3/1074

Head room Shoulder room Hip room Leg room

37.8/960 58.6/1488 57.2/1453 37.6/955

LUGGAGE COMPARTMENT CAPACITY (cu. ft./liters) Luggage capacity3 (with space saver) EPA passenger compartment volume index3

18.6/526 104.8/2968

CITY/HIGHWAY/COMBINED

3.6L engine4



17/28/21

EPA label values, actual mileage will vary with options, driving conditions, driving habits and vehicle condition.

ALTERNATOR SC3 170

77ºF (25ºC)

KW7 Impala POLICE ALTERNATOR OUTPUT

200 190

3

180

77° F (25° C)

2

170

1

160

0

150

No Load Idle 625

140

221° F (105° C)

257° F

130

Automatic, electronically-controlled with overdrive Fluid pan removed & filter replaced (quarts/liters)

AXLE Ratio

(125° C)

Type Size Type Size

Park/Neutral 800 1000 1100 1200

Drive 800 800 800 800

3. Cargo and load capacity limited by weight and distribution. 4. EPA-estimated MPG. 5. Gross Vehicle Weight Rating (GVWR). When properly equipped, includes vehicle, passengers, cargo and equipment. 6. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo. 10. Curb weight in operational status with 100% fuel, fluids and standard base equipment (excludes optional content) * Published dimensions indicated are at curb weight

Steel 17" x 7.5"

CHASSIS Frame Engine cradle Front suspension Rear suspension Steering type Steering ratio (center)

BATTERY

2000

All Season W-speed rated P235/55R17

WHEELS

Type Bci group size Volts Amp hour rating Cold cranking-amps @ 0°F (-18°C) Reserve capacity @ 80°F (27°C)

100

Disc/Disc 246.3/1589.6 175.8/1134 422.1/65.5 12.7/323 10.9/277 1.2/30 .5/14

TIRES

110

Boost Level 0 1 2 3

2.44

ABS with vacuum boost Front - swept area (sq. in./sq. cm) Rear - swept area (sq. in./sq. cm) Total front and rear swept area (sq. in./sq. cm) Front rotor diameter (in./mm) Rear rotor diameter (in./mm) Front rotor thickness (in./mm) Rear rotor thickness (in./mm)

120

1000

6-speed 7.4/7.0

BRAKES

REAR COMPARTMENT (in./mm)

Type Amps

V6 3.6/217 302/6800 262/5300 SIDI 11.5:1 Single with dual outlets 87 17.5/66.2 4.0/3.8 10.6/10.0

TRANSMISSION

FRONT COMPARTMENT (in./mm)

FUEL ECONOMY RATINGS

Type Displacement: liters/cu. in. Horsepower/rpm Torque lb.-ft./rpm Induction system Compression ratio Exhaust Minimum recommended fuel octane Fuel tank capacity (gallons/liters) Oil with filter (quarts/liters) Cooling capacity (quarts/liters)

Unitized body Aluminum Independent MacPherson Strut, coil spring over strut and stabilizer bar Independent Tri-Link MacPherson Strut, coil spring over strut and stabilizer bar Power rack and pinion 14.1:1

VEHICLE WEIGHT (lbs./kg.) GVWR5 Curb weight10 Payload6 (includes 5 passengers and space saver spare tire)

Maintenance free 34 12 70 720 125 minutes 9C1 9C3 4938/2240 4938/2240 3736/1695 3743/1698 1140/517 1173/532

NOTE: See your vehicle tire and loading information label for specific weight values. See your owner's manual supplement for proper cargo loading distribution

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited 9c1 & 9c3 Police PKG - Dimensions | 11 IMPALA POLICE PACKAGE

Front Side Glass 29” w x 15.5” h 58”

31”

27.5”

Rear Qtr. Glass 12” w x 12” h

Rear Side Glass 27.5” w x 15.5” h

40” 18”

39”

43”

28.5”

79.5” 200.5”

Shown with optional body side moldings and rear spoiler

56” 40”

15”

84”

62.5”

42.5” 49”

80” Rear Window 50.5” w x 31.5” h

Estimated material sizes to wrap: • Hood – 60” x 65”

• Front Doors – 46” x 30” • Rear Doors – 43” x 32” • Roof – 87” x 48” • Trunk Lid – 36” x 53”

15” IMPALA

8”

49.5” 20”

*Optional rear spoiler and bodyside moldings shown

2014 Chevrolet Municipal Vehicles Technical Manual

12 | Impala

LIMITED 9c1 & 9c3 – Special Paint Available

To accommodate customers who require special painted vehicles, orders will be sent to Kerr Industries who will special paint the cars once they are built. Please note: this ordering process is substantially different from the way special paint is ordered on other vehicle lines and requires an additional charge. See your local dealer for current pricing. It is recommended that the customer review the first vehicle painted when special paint is ordered, however it is not mandatory. If the customer chooses not to review a pilot vehicle, Kerr Industries will require sign off by the customer before the vehicle will be released. Customer and dealer costs associated with accommodations and travel for in person review of special paint are the responsibility of the dealer.

To Order Special Paint

• RPO White 50u or RPO Black 41u must be ordered



• T he 4-digit special paint code in paint code 1/paint code 2 fields will be replaced by options denoting code 1 and code 2 colors



• Paint scheme codes will be replaced by options



• Solid color option is aas



• 2-tone color option is aat



• W  hen special paint schemes are ordered only class A surfaces will be painted; mirrors and handles are NOT painted. For additional costs to have the handles and mirrors painted please contact Kerr Industries at 905-725-6561.



• It is recommended that all vehicles be ordered in Black 41u before special paint is applied.



• For paint colors not listed in this brochure please contact Kerr Industries directly at 905-725-6561

Example for Ordering Special Paint: If a dealer wants a Silver and Blue car with scheme w002, order 50u or 41u (White or Black rPO paint), options Bep (code 1 Blue), bfr (code 2 Silver), 1pb (paint scheme w002) and aat (2-tone paint)

Special Paint Warranty

• Warranty claims for special paints must be directed to Kerr Industries at 905-725-6561

After you have ordered special paint

• A fter the vehicles have been ordered for special paint, kerr Industries will contact the dealer directly regarding colors and verification of the scheme. Once verified a special paint build sheet will be sent to the dealer for final confirmation. This sheet will need to be signed by the dealer and returned to kerr Industries before painting will commence.

NOTE: T he attached list of paint options contain the same WA numbers in the code 1 and code 2 columns. It is extremely important that the dealer order the correct code 1 and code 2 options so the upfitter knows how to paint the vehicles.

NOTE: For paint colors not listed please contact Kerr Industries directly at 905-725-6561

2014 Chevrolet Municipal Vehicles Technical Manual

Impala LIMITED 9c1 & 9c3 – Special Paint Available | 13

OPTIONS

WA#

COLOR DESCRIPTION

CODE 1

CODE 2

121A

Adriatic Blue



BEA

BFE

311B

Olive



BEB

BFF

5120

Blue



BEQ

BFU

5236

Neutral



BEC

BFG

5322

Driftwood



BER

BFV

5665

Blue



BED

BFH

5749

Gold



BES

BFW

5845

Beige



BEE

BFI

7153

Blue



BET

BFX

7159

Blue



BEF

BFJ

7262

Brown



BEU

BFY

7801

Brown



BEG

BFK

7840

Silver



BEV

BFZ

7868

Blue



BEH

BFL

7888

Blue



BEW

BGA

7889

Blue



BEP

BFT

7964

Green



BEI

BFM

7999

Blue



BEX

BGB

8380

Blue



BEJ

BFN

8381

Gray



BEY

BGC

8401

Yellow



BEK

BFO

8412

Green



BEZ

BGD

8431

Rose Metallic



BEL

BFP

8554

White



BFA

BGE

8555

Black (41U)



BEM

BFQ

8624

Summit White (50U)



BG8

BGK

8743

Blue Black



BFB

BGF

9021

Silver



BEN

BFR

9382

Blue



BFC

BGG

9403

Tan



BEO

BFS

Actual Color May VAry

2014 Chevrolet Municipal Vehicles Technical Manual

14 | Impala

LIMITED 9c1 & 9c3 – PAINT SCHEMES

SEO Color scheme #w001 option code 1pa

paint code 1 legend: code 2 SEO Color scheme #w002 option code 1pB

paint code 1 legend: code 2 SEO Color scheme #w003 option code 1pC

paint code 1 legend: code 2 SEO Color scheme #w006 option code 1pF

paint code 1 legend: code 2 SEO Color scheme #w008 option code 1pH

paint code 1 legend: code 2 SEO Color scheme #w009 option code 1pI

paint code 1 legend: code 2 SEO Color scheme #w012 option code 1pL

paint code 1 legend: code 2

2014 Chevrolet Municipal Vehicles Technical Manual

Impala LIMITED 9c1 & 9c3 – DRiver Info center | 15 United States Certified Speedometer/cluster (Canadian Similar)

Driver Information Message Center

Automatic Lamp control on† automatic lamp control off† battery saver active Certified speedometer†† change engine Oil soon check tire pressure digital mPH readout††† driver door open Engine Hot Turn A/C Off Engine Overheated idle engine Engine Overheated Stop Engine Engine Power is Reduced Error Fuel Level Low Hood Open Ice possible drive with care Left rear Door Open Oil Pressure Low Stop engine Passenger Door Open Remote Key Learning Active Replace Battery In Remote Key Right Rear Door Open Service A/c System Service Air Bag Service Battery Charging System † Message may not be displayed in Police Package †† Message flashes at engine start ††† Can be set as default condition

Service Brake System Service Power Steering Service stabilitrak Service Theft System Service Tire Monitor System service traction control Service Transmission Service Vehicle Soon stabilitrak initializing StabilitraK off Starting Disabled Service Throttle Theft Attempted† Tighten Gas Cap tire learning active tire low add air to tire traction control off traction control on Transmission Hot Idle Engine Trunk Open Turn Signal On washer fluid low add fluid Speedometer certification 2014 Impala police cars certified speedometer calibration. Specifications, at ambient temperature of -10 to 120 degrees F. Inaccuracies due to vehicle speed sensing are included. Actual vehicle speed indicated speed 0 to 120 mph +/- 2 MPH The speedometer calibration is for the 3.6L engine, automatic transmission with a 2.44 axle and P235/55R17 W-rated tires

2014 Chevrolet Municipal Vehicles Technical Manual

16 | Impala

LIMITED 9c1 & 9c3 special Equip – STD

Wiring Provisions for 12-Volt Battery Power Supply

Battery power is supplied through two fusible links, one 50-amp and one 65-amp, to three circuit breakers and two control relays located in the control center above the accelerator pedal. A 50-amp circuit breaker feeds power directly from the 50-amp fusible link through a 10-gauge blunt cut wire. Two 30-amp circuit breakers supply power from the 65-amp fusible link through the contacts of the control relays to 12-gauge blunt cut wires. The blunt cut leads are part of a 5-foot coil on the floor under the instrument panel. Each relay is to be operated by an 18-gauge control lead included in the 5-foot coil under the instrument panel. An 8-gauge system ground lead is also provided in the 5-foot coil. The total current available through the 12-volt power supply is 110-amps. Two blunt cut wires provide ignition controlled power; one is hot when the ignition is in Accessory/On; the second is hot when the ignition is in START/ON. A third blunt cut wire from the body control module provides a park-enable signal. When the transmission is in PARK, zero volts (not ground) are present and 12-volts are present when the transmission is in any other position. The circuit is designed to operate a single customer-furnished relay. A fourth blunt cut wire provides the Vehicle Speed Signal (VSS). NOTE: For wiring diagram see page 23

Fuse Block Battery Power Supply

Auxiliary Battery Power Junction Block in trunk

The auxiliary battery power junction block is mounted in the trunk of your Impala police vehicle. It is located on the passenger side support strut behind the rear wheel housing. This junction block is split to provide two circuits and can be used to connect customer-furnished equipment directly to the battery through 8-gauge (8 mm2) body wiring and fusible links. A maximum of 100-amps (1200-watts) can be connected. Torque the connections to the studs to 11 lb.-ft. (15 N-m). It is fed by two fusible links of 50-amps each. NOTE: For wiring diagram see page 23

Trunk Ground Stud

A 10 mm ground stud can be found in the trunk on the passenger’s side of the vehicle. The stud is located above the trunk auxiliary junction block. See “Trunk Auxiliary Battery Power Junction Block” for more information on location. A 10 mm flanged hex nut grounds the 10 mm bolt to the vehicle. Recommended torque for the flanged nut is 26 lb.-ft. (35 N-m), plus or minus 4 lb.-ft. (5 N-m). A 10 mm hex nut is provided for customer ground termination. Recommended torque for the terminal connection nut is 7.3 lb.-ft. (10 N-m), plus or minus 1 lb.-ft. (1.3 N-m).

Keylock Cylinder – Trunk Lid

If your vehicle is equipped with the Theft Deterrent System (option UA6), an audible alarm will occur when the key is used to open the trunk instead of the remote keyless entry (transmitter). See your dealer/retailer to disable the audible alarm.

Enlarged View of the Battery Power Fuse Block

Servicing Relays and Circuit Breakers The following information shows you where the relays and circuit breakers are located in the fuse block, viewed upward from driver floor. A. Instrument panel carrier B. Relay center for circuit breakers and control relay C. Instrument panel harness branch

A. Relays and circuit breakers, B. Front of the vehicle, C. Floor of the vehicle

2014 Chevrolet Municipal Vehicles Technical Manual

Impala LIMITED 9c1 & 9c3 special equip – STD | 17 Tire Pressure Monitor

EXTERIOR LAmpS CONTROL Headlamp Switch

Trunk Opener Interior Lighting Dimmer Stabilitrak

Your vehicle is equipped with a Tire Pressure Monitor (TPM) System which warns of low tire pressure. Your Impala Police Package may be equipped with a full-size spare tire (see page 18) The full-size spare tire has a sensor but is not programmed to read the spare tire pressure. When the full-size spare tire from your vehicle or spare tire from another Police Package is placed in use as a road wheel, the system will not read the presence of the new TPM sensor and must be calibrated. Refer to your owner’s manual for additional information on the Tire Pressure Monitor and Sensor Programming. The space saver spare tire does not have a tire pressure monitor.

Cooling System

9G8 - Delete Daytime Running Lamps and Automatic Headlamps. This option disables the Daytime Running Lamps and Automatic Headlamps control feature. Exterior lamps are manually controlled only. Option 9G8 is not available in Canada. The headlamp control on the driver’s side of the instrument panel operates the headlamps. If your Impala does not have option 9G8, Daytime Running Lamps and Automatic Headlamps delete, the Daytime Running Lamps and Automatic Headlamps can be turned off for one ignition cycle by rotating the control knob momentarily counterclockwise. Rotating the headlamp switch again will turn the Daytime Running Lamps and Automatic Headlamps back on. In Canada, the Daytime Running Lamps and Automatic Headlamps can be turned off if the transmission is in Park. See also section 1 of your Impala owner’s manual. Stabilitrak - The Stabilitrak stability control system button is located below the dimmer control as part of the headlamp switch. Refer to pages 3 or 7 of this manual for an operation description of the stablity control system or see your Owners Manual.

Strengthened Front Seat

High capacity radiator with 225-watt fans

A

Engine, transmission and power steering coolers Engine Oil Cooler

Transmission Cooler

B C

Seat bottom frame structural tubes - A, B Center floor tunnel-mounted crush box - C NOTE: Do not remove the crush box for aftermarket equipment installation

Service parts identification label Power Steering Cooler

E L MP

SERVICE PARTS IDENTIFICATION

DO NOT REMOVE

2G1WD5EM3B1142351 Three auxiliary air-to-oil coolers are mounted in front of the engine coolant radiator. The transmission cooler is connected in series with the coolant radiator end-tank cooler.

Mat – Trunk

AGK BDR IPG OST UW6 3FL 7X6 BC/CC

AG2 B3B JA9 QPP UIC 6A3 8MZ

AL0 AMF B42 B86 JL9 KD1 R7V R9N U77 VT7 6E2 6HP 9C1 9MZ U 636R

SA

AP3 B9V KG4 R9Z V8D 6J1

AR9 C67 LGD SLM WL9 6J3

AT8 DK2 MX0 T53 ZFH 6J4

PDBJCH AXJ AY0 EF7 E2C M15 NK5 UH8 UJM 1SZ 19C 6J7 7B3

A75 FE9 NT7 UN9 50U 7HP

1SW19 A76 FR9 N99 UT7 191 7M9

A Service Parts Identification (SPID) Label provides Vehicle Identification Number (VIN)-specific Option Code content list, Engineering Model Number (Nameplate, body style), Exterior paint system, Exterior paint color code and Interior trim level and color. The SPID label for the Impala is located on the right side rear compartment floor. The rear compartment trim must be lifted to access the label. Heavy-duty mat covers floor.

2014 Chevrolet Municipal Vehicles Technical Manual

18 | Impala

LIMITED 9c1 & 9c3 special Equip – Opt

6C8 – Wiring Coaxial Radio Antenna Cable

RG58 Coaxial radio antenna cable routed from just rearward of the dome lamp location to trunk. Approximately 24 inches of extra cable is coiled between headliner and roof panel. A coil of sufficient length to reach either corner of the trunk is secured to the right inner wheelhouse. There is no hole in the roof panel.

7Y6 – Lamp Inoperative Dome

Dome and courtesy lamp will not operate when doors are opened. Dome lamp is controlled only by the instrument light dimmer on the instrument panel.

6C7 – Lamp Auxiliary Dome Autonet Mobile wifi; in-car router

Delivers high speed network connectivity to vehicles by leveraging the 3G network. Autonet Mobile's TRU Technology, a proprietary and patented technology, provides a seamless connection regardless how fast you are traveling. Unlike conventional cellular data technology, TRU Technology manages data as users travel at high speeds between cell towers, eliminating dropped connections. CarFi™ provides wireless device connectivity within the vehicle using standards-based 802.11 Wi-Fi networking. This allows users in and around the vehicle to access the Internet using any Wi-Fi enabled device. Available through your GM dealer.

Dome lamp located between visors with switch at base of lamp, red LED/white incandescent auxilary wired independently from standard dome lamp.

RUF – FULL SIZE SPARE Tire

Cover is provided for spare tire and wheel. Full-size spare tire is mounted on top of the standard trunk trim covering the space saver spare tire tub. If full-size spare tire is removed, tub is exposed. The full-size spare tire includes a Tire Pressure Monitor (TPM) sensor which must be programmed to the TPM System after the spare tire is installed. (see page 17)

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited 9c1 & 9c3 special Equip – Opt | 19 6J7 – Exterior Lamps Emergency Flashing System module location

This option 6J7 Exterior Lamp Emergency Flashing System module is mounted on the front of the right hand upper radiator support, below the upper radiator air baffle NOTE: For wiring diagram see page 24

6J6 – LAmps Rear Window

Two 4-inch, red, single-faced lamps are mounted behind rear seatback to be viewed through rear window. The turn signal circuits extend in loops coiled in the right front foot well for customer connection to control switching. These lamps function as auxiliary turn signal, stop lamps and vehicle hazard flashers.

T53 – LAmps Trunk Lid Warning

6J7 – Exterior Lamps Emergency Flashing System

Option 6J7 provides a headlamps high beam flashing module, rear lamps flashing via the Body Control Module (BCM) and a control wire for customer-furnished switching to turn the module on and off. The flasher control wire is part of the blunt-cut upfitter harness coiled under the instrument panel in the front passenger side foot well. The flashing module is located is located on the front side of the upper radiator support at the inboard end of the passenger side headlamp assembly. The headlamp flashing module is activated by the application of 12 volts to a dark green/red wire in the upfitter harness. When activated, the headlamp high beams and the high beam instrument cluster indicator will flash alternately at 2.4 flashes per second. When the flashing module is turned on, the module sends a signal to the BCM which alternately flashes the stop lamps and backup lamps at the same flash rate as the headlamps. Depressing the brake pedal will override the stop lamp flashing and placing the transmission in Reverse will override the backup lamps flashing. During daylight conditions, the Daytime Running Lamps (DRL) are automatically turned off whenever the headlamps flashing module is activated. During night time conditions, the low beam headlamps automatically turn on while the high beam lamps flash. Turning on the high beam headlamps manually will override the flashing module and the high beam headlamps will operate continuously. During night time conditions the tail lamps will turn on automatically. If Option 9G8 is present the low beam headlamps and tail lamps will not come on automatically. The Center Mounted Stop Lamp will operate only when the service brakes are applied. A 15-amp fuse labeled HDLP MDL protects the flasher module circuit. The fuse is located in the under hood fuse block in the engine compartment on the passenger side of the vehicle. See also the Owner Manual for more information. Activation of the headlamps flashing and rear lamps flashing can be separated by opening the dark-blue/yellow BCM circuit at the flasher module connector, C122-F, and applying a customer-switched ground to the harness side of the wire at the connector. Power to the dark green/1209 wire must be off to flash the rear only.

Warning: BCM will be damaged if 12V power is connected to the dark-blue/ yellow wire.  NOTE: For wiring diagram see page 24

Two 4-inch, red, single-faced lamps are mounted to the deck lid inner panel. Lamps are activated by the deck lid ajar mechanical switch when deck lid is opened. Lamps are wired to flash alternately through a flasher located at the upper right hand corner of the trunk opening. Wiring is protected by fuse HTDSEAT in the engine compartment fuse block

2014 Chevrolet Municipal Vehicles Technical Manual

20 | Impala

LIMITED 9c1 & 9c3 special Equip – Opt

7x6 and 7x7 Spotlamps 7x8 and 7x9 Spotlamp Provisions

AMF – PACkage of 6 Transmitters

With Remote start

7x6 Spotlamp left hand, pillar-mounted unity, 6-inch with replaceable h3 halogen bulb; independently fused 7x7 Spotlamps left and right hand, pillar-mounted unity, 6-inch with replaceable h3 halogen bulb; independently fused 7x8 Spotlamp provision left hand provision for customer installed spotlamp includes hole through pillar, mounting bracket and accessible power connector 7x9 Spotlamp provision left and right hand includes same components as option 7x8 NOTE: • Lamp bulbs are halogen 12volt 100 watt H-3 rated at 245,000 candle power • For wiring diagrams and fuse location see page 25 • Customer furnished spotlamp assembly must be installed to avoid interference with deploying passenger airbag

6B7 and 6J5Hole in Roof Panel

Without Remote start

Relearn Remote Key To access this DIC display, the vehicle must be in PARK. This display allows you to match the remote keyless entry transmitter to your vehicle. To match a remote keyless entry transmitter to your vehicle, do the following: 1. Press the vehicle information button until PRESS THE RELEARN REMOTE KEY displays. 2. Press the set/rest button. The message REMOTE KEY LEARNING ACTIVE will display. 3. Press and hold the LOCK and UNLOCK buttons not the first transmitter at the same time for approximately 15 seconds. A chime will sound indicating that the transmitter is matched. 4. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it. 5. To exit the program mode, you must cycle the key to OFF. NOTE: A maximum of 8 keys may be learned for a vehicle immobilizer (Passkey III+) with a random key code. Vehicles with the fleet key option (RPO 6E2 or 6E8) may have an unlimited number of keys learned for the particular option fleet key and must be learned using one of the original "master" keys. When programming RPO AMF additional 6 remote transmitters, the original 2 transmitters delivered with a vehicle must also be reprogrammed at the same time. A maximum of 8 remote transmitters can be programmed for a single vehicle.

655 – Roof wiring

6B7 Hole is drilled near center line of roof panel approximately 29 inches rearward of windshield opening 6J5 Hole is drilled on passenger side of roof panel approximately 29 inches rearward of windshield opening and approximately 6 inches inboard from passenger side door NOTE: O  nly one roof hole location may be ordered. SEO 6F5 roof wiring is required when SEO 6B7 or SEO 6J5 are ordered.

Option 6F5 is a universal wiring harness for roof-mounted equipment. The harness is routed from a 5-foot (1.5 m) coil of wire in the passenger’s side footwell to a connector on the passenger’s side of the trunk. When the option 6B7 (center hole) is ordered, two color coded 10-gauge (5.0 mm2) wires extend 24-inches (60 cm) through a grommet approximately 30-inches (74 cm) behind the top of the windshield at the center of the roof. When option 6J5 (passenger’s side hole) is ordered, two color-coded 10-gauge (5.0 mm2) wires extend 24-inches (60 cm) through a grommet approximately 30-inches (74 cm) behind the top of the windshield and 6-inches (15 cm) inboard from the passenger’s side roof joint. NOTE: For wiring diagram see page 25

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited 9c1 & 9c3 special Equip – Opt | 21 6j4 – wiring Provision for Horn/ Siren Circuit

This provision permits customer connection of a switch to select either horn or siren operation when the horn pad is pressed. A 22-gauge (0.35 mm2) wire is connected to an in-line connector in the horn circuit of the instrument panel harness under the instrument panel. The end of this harness extension is in a 5-foot (1.5 m) loop of wire coiled under the instrument panel. NOTE: For wiring diagram see page 25

WX7 – WIRING PROVISION FOR FRONT SPEAKERS

Approximately 60 inches (1.5 m) of auxiliary speaker wiring is routed from the front door and windshield pillar speakers and coiled under the instrument panel. The wiring permits connection of the front speaker pairs to customerinstalled communication equipment. Vehicle radio front speaker outputs are re-routed to the rear speakers to maintain the required open door/key-inignition audible warning. NOTE: For wiring diagram see page 24

6J3 – Wiring Provisions for Vehicle Grille Lamps and Speaker/Siren

A. B lunt cut ends for the customer-furnished grille lamps and customer-furnished siren/speaker B. Control wires from in-line connector in forward lamp harness for customerfurnished grille lamps and speaker The seo 6j3 wiring provision has a 5-foot (1.5 m) harness coiled underneath the instrument panel on the passenger side. The wiring circuits are routed from under the instrument panel to a 1-foot (30 cm) coil secured in the area behind the grille. There are four 16-gauge (1.0 mm2) wires for connecting to the grille lamps (gry, tan) and siren speaker (lt bu, lt gn) The seo 6j3 wiring provision also includes one 18-gauge (0.8 mm2) control wire for the seo 6j7 exterior lamps Emergency Flashing System. When option 6j7 is installed without option 6j3, only the dark green/red control wire is provided for connection to customer-furnished 12-volt switching to turn the Emergency Flashing System on or off.  See also page 19. NOTE: For wiring diagram see page 24

2014 Chevrolet Municipal Vehicles Technical Manual

22 | Impala

LIMITED 9c1 & 9c3 special Equip – Opt

6N6 – Locks Rear Door Inoperative

Rear door locking rods are disabled. Rear door locks are inoperable at rear doors, but operate from driver position. Remote rod is shipped in the glove box for future installation.

6N5 – window SWITCHES REar door Inoperative

6A3 – Floor Covering

Black heavy-duty front and rear. Replaces production carpeting.

6B2 – Handles Rear Door Inoperative

Inside rear door handles are disconnected. Rear doors can only be opened from the outside. Rear door window switches are inoperable. Rear door power regulators are operable only from driver position switches.

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited 9c1 & 9c3 – Wiring Diagrams Wiring Diagram for 12-Volt Battery Power Supply

Battery power is supplied through two fusible links, one 50-amp and one 65-amp, to three circuit breakers and two control relays located in the relay center above the accelerator pedal. A 50-amp circuit breaker feeds power directly from the 50-amp fusible link through a 10-gauge (5.0 mm2) blunt cut wire. Two 30-amp circuit breakers supply power from the 65-amp fusible link through the contacts of the control relays to 12-gauge (3.0 mm2) blunt cut wires. The blunt cut leads are part of a 5-foot (1.5 m)

Wiring Diagram for Controlled power and signal circuits with 12-volt power supply

loop of wire coiled under the instrument panel in the passenger’s side footwell. Each relay is operated by an 18-gauge (0.8 mm2) blunt cut, light or dark blue control lead included in the 5-foot (1.5 m) coil under the instrument panel. An 8-gauge (8.0 mm2) ground lead is also provided in the 5-foot (1.5 m) coil. The total current available through the 12-volt power supply is 110-amps (1320-watts).

Wiring diagram for auxiliary battery power junction block

Hot Out of Park

Bunt cut ignition controlled power and signal circuits are also included in the following 5-foot (1.5 m) right foot loop. The spotlamp fuses are located in the passenger’s side underhood fuse block. See “Fuses and Circuit Breakers” in your owner’s manual index for more information. • A yellow, 20-gauge (0.5 mm2) 10-amp fused circuit, hot in ACCESSORY, RUN or RAP (Retained Accessory Power) Fuse “RAP” is in the end of the instrument panel. • A pink, 20-gauge (0.5 mm2) 10-amp fused circuit, hot in START/RUN. Fuse “PWR Drop/CRNK” is in the underhood fuse block. • A yellow/black, 20-gauge transaxle park signal from the Body Control Module (BCM). This circuit provides switched power (12-volts) when the transmission is not in PARK (P) and the engine is running. The electrical load attached to the park circuit must not exceed 0.5-amps (one relay coil). • A brown, 22-gauge (0.35 mm2) vehicle speed signal (4,000 pulses/mile) from the ABS module. Connect only high impedance load. NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

| 23

24 | Impala

Limited 9c1 & 9c3 – Wiring Diagrams

Wiring Diagram for Forward Lamp Harness In-Line Connector for use with Headlamps Flasher Module, Option 6J7 Warning: BCM will be damaged if 12V power is connected to the dark-blue/yellow wire. 

From blunt-cut wire under instrument panel

This connector is located at the rear passenger side of the bumper beam.

Wiring diagram for option 6j3 and option 6j7

Wiring Diagram for OPTION WX7 in-line Connector Chime Level Adjustment Impala police vehicles are equipped with a radio that provides an AM/FM stereo with a CD player. The radio produces a Federally mandated audible warning notification for the vehicle. The volume level of the chimes can be adjusted to be louder, but cannot be turned off. See “Climate Controls” and “Audio Systems” in your Impala owner’s manual to adjust the chime volume or contact your dealer for assistance.

WX7 inline harness added here to send LF and RF outputs to LR and RR speakers. Blunt cut circuits from front speakers are coiled in front under the instrument panel.

NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited 9c1 & 9c3 – Wiring Diagrams

| 25

Wiring Diagram for OPTION 6F5

wiring DIAGRAM FOR OPTION 6J4

Wiring Diagram for WINDSHIELD PILLAR-MOUNTED SPOTLAMP - OPTION 7X6 and 7X7

LT SPOT Minifuse 15A

UNDERHOOD FUSE CENTER RT SPOT Minifuse 15A

-Spotlamp LH 2640 0.5

RD/WH

J2

P2

B3

RD/WH

2640 0.5

RD/WH

2740 0.5

H7635

A PWR

CASE GND

-Spotlamp RH 2740 0.5

RD/WH

J2 B3

P2

H7635

A PWR

CASE GND

7x6 spotlamp left hand and 7X7, spotlamps left and right hand, pillar-mounted Unity, 6-inch with replaceable h3 halogen bulb; independently fused

NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

26 | AIR

BAGS FAQ

Can specialty vehicle equipment (e.g. radar devices, video cameras, computers, meters, radio trees, shotguns, etc.) still be mounted in cars with passenger side air bags? Yes, but care must be taken to mount the equipment outside of the deployment zone. Air bags inflate with great force and will interact with any object in the deployment zone. Therefore, to reduce the risk of injury to vehicle occupants, GM recommends that the air deployment zone be kept free of any equipment. If a piece of equipment were to become dislodged it could strike an occupant in the vehicle and result in injury. The likelihood of an object becoming dislodged is influenced by many factors, including the proximity of the object to the inflatable restraint, the size and shape of the object, and the means by which the object is secured to the vehicle. In addition to these factors, the trajectory and velocity of a dislodged object can be influenced by the type and severity of vehicle crash. Objects that are in the deployment zone, but do not become dislodged by an inflating air bag can still affect the performance of the air bag. For example, such objects could tear the fabric or affect the shape of the air bag, thus reducing the ability of the bag to provide restraint. Is it possible to shield equipment that is installed in the passenger side frontal air bag deployment zone in a manner that will allow full and safe air bag deployment? Due to the complexity of influencing variables, GM is unable to evaluate the potential for shielding expected equipment configurations in all accident scenarios in order to assure that the air bag performance would be unaffected. While shielding may protect certain equipment from being damaged or dislodged, it may also negatively affect the inflation characteristics of the air bag. The air bag’s shape, inflation angle, fold pattern, and inflation rate and pressure are developed to maximize the protection capability of the inflatable restraint system. Therefore, GM cannot recommend the placement of any equipment in the deployment zone, even if it is shielded to protect it from damage. Front air bag systems and instrument panel mounted equipment. Passenger air bags in GM vehicles deploy in different ways depending upon the type of vehicle and the particular instrument panel design. In some vehicles, the passenger air bag deploys through a discrete door located on the top surface of the instrument panel (top-mount air bag systems). In other vehicles, such as the Chevrolet Tahoe, the passenger air bag deploys through a discrete door mounted on the vertical rearward surface of the instrument panel, above the glove box door (mid-mount air bag system). With these types of topmount and mid-mount passenger air bag systems, the top pad of the instrument panel remains in place during deployment. Some GM passenger air bag systems, like the system in the Chevrolet Impala, deploy from beneath the instrument panel top pad. These are considered 3/4-mount air bag systems with a “deployable top pad.” The entire instrument panel top pad is the “deployment door” from under which the inflating air bag emerges. When an air bag deployment is commanded, the forces from the inflating passenger air bag push up on the instrument panel top pad, releasing special fasteners across the rearward edge of the top pad. This allows the top pad to rotate upward so that the passenger air bag may emerge. The top pad rotates upward to open widest at the right hand side, and is usually forced upward into contact with the windshield on the right hand side of the vehicle during a deployment.

Instrument panel top mounted special equipment, such as a radar antenna and control unit or video camera must be positioned to the left of the vehicle center line. This equipment must be mounted as low as possible and securely fastened to the top pad to avoid being dislodged in the event of a crash and possible air bag deployment. In the process of securely fastening special equipment to the top, DO NOT fasten down the top pad itself to any other vehicle component such as the cluster trim plate. As described above, the top pad rotates upward during a deployment. In order to enable the proper deployment of the passenger air bag, specialty equipment installation MUST NOT PREVENT the top pad from rotating upward during deployment. Location and attachment of special equipment should minimize added resistance or interference to upward rotation of the top pad during deployment. Side-Impact Air Bags for crashes to the vehicle sides. The air bag system in your police vehicle includes includes roof rail mounted Head Curtain side air bags.. The vehicle is also equipped with seat back mounted upper body air bags located on the outboard side of the driver and front passenger seat backs. Together the Head Curtain and seat-mounted side air bags are intended to protect the head and upper body in the event of a side crash. Some vehicles may also be equipped with an optional air bag, mounted on the inboard side of the driver seat back. Can Specialty Vehicle Security Barriers be mounted within the side air bag deployment zones? No. The side air bags inflate extremely fast because of the nature of side crashes to the vehicle. Mounting a security barrier behind the front seats with the ends placed within the side air bag deployment zones will result in unintended interaction between the barrier and the inflating side air bags. To reduce the risk of injury to the vehicle occupants, GM recommends that the side air bag zones be kept free of any customer installed equipment. Customer furnished equipment installed to the vehicle roof. Your police vehicle is designed with an interior roof cover system which includes internal components for the interior lamps and wiring. The roof system may also include side air bag components. Inflation devices may be mounted on the vehicle roof side behind the rear doors as well as air bag tethers retained to the windshield pillars. Care must be taken to avoid damage to these components or interference with their operation when installing roof mounted equipment such as emergency lamps and communication antennas. Recommended GM service procedures must be followed to remove and re-install the instrument panel top pad to ensure that the top pad will release properly in the event of a passenger air bag deployment. On the right half of the top pad closest to the passenger air bag module, GM recommends that no equipment be mounted. When mounting equipment on the driver side of the top pad, GM recommends that the total mass of the top pad mounted special equipment not exceed 8 pounds (3.6 kilograms), since some top pads tend to rotate about the left end. Fasteners used to secure special equipment to the instrument panel top pad, the windshield glass, or to the windshield upper frame (header), should be selected to ensure that these devices will remain attached during a vehicle crash and possible air bag deployment.

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

AIR BAGS FAQ | 27 Can the installation of push bumpers on the front end of the vehicle affect the deployment of the air bag?

I've heard that a deployed air bag produces whet appears to be smoke, is the air bag hot?

General Motors is not aware of adverse effects during crash events from the many push bumpers thai have been installed on GM police vehicles. Because there are many styles of push bumpers available with varying crash characteristics, installation of push bumpers may or may not affect deployment timing of the air bags. Push bumpers should be mounted to avoid modifying the vehicle structure and interfering with the front air bag sensors mounted on the upper radiator support cross member

After the bag has deployed in a crash, the air bag itself will not be hot to touch. Some components within the air bag module will be hot for a short time. A small amount of smoke coming from a deployed air bag module is normal and should not be cause for concern.

Two front impact sensors are installed in General Motors vehicles. Do not relocate or disconnect the front sensors. The location and orientation of the front sensors are critical for correct operation of the air bag system. Avoid mounting components on or near the sensors. Push bumper styles with vertical pushing members that are in foreaft alignment with the front air bag sensors are not recommended. When should an air bag inflate? The driver's and right-front passenger's frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system's designed "threshold level." In addition, your vehicle has “dual stage” frontal air bags which tailor the the amount of restraint according to crash severity. For moderate frontal impacts, the air bags inflate at a level less than full deployment. For more severe frontal impacts, "dual stage" frontal air bags deploy at full levels. If the front of your vehicle goes straight into a wall that doesn't move or deform, the threshold level of the reduced deployment is about 12 to 16mph (19 to 15 km/h), and the threshold level for a full deployment is about 18 to 24 mph (29 to 28.5 km/h). The threshold level can vary, however, with specific vehicle design, so that it can be somewhat above or below this range. If your vehicle strikes something that will move or deform such as a parked car, the threshold level will be higher. The driver's and right-front passenger's frontal air bags are not designed to inflate in rollover, side impacts, or rear impacts, because inflation would not help the occupant. Seat mounted side impact air bags are designed to inflate in moderate to severe side crashes. The side impact air bags will inflate if the crash severity is above the designed "threshold level." The threshold level can vary with specific vehicles design. The side impact air bags are not designed to inflate on frontal or near-frontal impacts or rear impacts, because inflation would not help the occupant.

Also, when the nitrogen gas is vented out of the air bag, small particles from inside the bag are also vented into passenger compartment. These airborne particles look like smoke and some particles are deposited as residue on and around the air bag. I've heard that the dusts that are released into the passenger compartment from the air bag are harmful, is this true? For most people, the only effect the dusts will produce is some irritation of the throat and eyes, and that is only if the occupant remains in the vehicle for many minutes after the air bag deployment with no ventilation and windows closed. However, some people with asthma may develop an asthmatic attack from inhaling the dusts. If this happens, they should first treat themselves the same way their doctor has advised them to treat any other asthma attack, and then immediately seek medical treatment. Can the air bag system be re-used? No, The air bags are designed to inflate only once. After inflation some new parts will be required. These will include the air bag module and possibly other parts. (A competent service technician with access to the vehicle's service manual and the required tools should replace the required components after a deployment crash.) If my vehicle has air bags, why should I have to wear my safety belt? Air bags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts not instead of them. Every air bag system ever offered for sale has required the use of safety belts. Even if you're in a vehicle that has air bags, you still have to buckle up to get the most protection. That's true not only in frontal collisions but especially in side and other collisions.

Roof rail mounted head-curtain air bags are designed to inflate in moderate to severe side crashes. In addition, certain vehicles have head-curtain air bags which are also designed to inflate in situations where an impending rollover condition is identified by the vehicle's rollover sensing system and/or frontal or near-frontal impacts if the crash severity is above the designed "threshold level". Safety belt pretensioners at the driver and front passenger seat positions are designed to deploy in frontal, near-frontal, side, and rear crashes that exceed the "threshold level" of crash severity to help reduce slack in the safety belt Safety belt pretensioners will also deploy in impending rollover situations. How long will the air bag remain inflated? It takes approximately 1/20th of a second to fully inflate the frontal air bags. This is faster than the blink of an eye. The air bags begin to deflate immediately, helping to stop the occupants more gradually.

2014 Chevrolet Municipal Vehicles Technical Manual

28 | Impala

Limited 9c1 & 9c3 – AIR BAG DimensionS FRONT COMPARTMENT PLAN VIEW

Top View of Instrument Panel and Approximate Deployment Area of the Air bag Zone A. Shift selector arc B. Driver side door C. Front of steering wheel (in maximum downward position) D. Driver air bag deployment zone E. Driver centerline (also see side view) F. Vehicle centerline G. Inside rearview mirror H. Passenger centerline (also see side view) I. Passenger air bag deployment zone J. Approximate maximum dimension of inflated air bag K. Passenger side door L. Rear edge of instrument panel top pad M. Zone from instrument panel top to windshield

FRONT COMPARTMENT SIDE VIEWs

Side View of Driver Side Air bag Deployment Zone - Centerline of Driver A. Driver air bag deployment zone B. Top of windshield C. Front of steering wheel (maximum downward position) D. Top of instrument panel

Side View of Passenger Side Air bag Deployment Zone - Centerline of Passenger A. Passenger air bag deployment zone B. Top of windshield C. Inside rearview mirror D. Top of instrument panel E. Passenger seat in foremost position F. Passenger seat in rearmost position

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

Impala Limited 9c1 & 9c3 – AIR BAG DimensionS | 29 Head curtain and Front seat-mounted side impact AIR BAG DEPLOYMENT ZONE RIGHT SIDE Shown, LEFT SIMILAR

A. B. C. D. E. F.

Top of deployment zone - along head curtain at edge of headliner Air bag inflator location on sail panel Back of deployment zone - at rear of quarter window Front of deployment zone - at front of outside mirror patch Forward air bag tether line Thorax air bag deployment zone

G. H. I. J. K. L.

Door handle front end Groove in front door armrest Pillar trim Approximate shape of deployed air bag at maximum size Bottom of deployment zone Bottom of door windows

Head curtain and Front seat-mounted Side impact AIR BAG DEPLOYMENT ZONES VIEW FROM REAR SEAT

A. Edge of headliner B. Underside of headliner C. Head curtain air bag deployment zone D. Inner center pillar trim E. Headrest

F. Inner door pad G. Seat centerline H. Bottom of door windows I. Thorax air bag deployment zone - front seat J. Groove in front door armrest

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

30 | Anti-lock

braking system FAQ

GM offers Anti-Lock Brake Systems as standard or optional on all North American passenger vehicles and light truck lines. The computerized Anti-Lock Braking System (ABS) is designed to keep the vehicle’s wheels rotating as the brakes are applied to assist the driver in achieving a controlled stop. Sensors monitor how fast the wheels rotate and feed the data continuously to the ABS computer. The vehicle’s brakes slow each wheel as the brake pedal is applied. However, when ABS is activated due to road conditions, the system repeatedly releases and applies pressure to the brakes. The wheels can keep rolling, thus retaining steering ability and enhanced stability while providing a higher braking force on most surfaces than a locked wheel provides. How exactly does ABS work? In cars without ABS, hitting the brakes can cause the wheels to lock, leaving you unable to steer the vehicle until you decrease the pressure so the wheels can roll again. With an ABS, as you apply the brakes, the ABS computer monitors the wheel speed sensor information. If the computer senses that a wheel is approaching lock up, it sends a signal to the hydraulic modulator to reduce, then to reapply, brake pressure several times a second for as long as you maintain firm pressure on the brake pedal. The process is much like the threshold braking technique used with conventional brakes. However, ABS does it much faster and more accurately than any driver can, leaving you free to focus on steering away from obstacles.

Does ABS reduce stopping distances?

Should I drive an ABS equipped vehicle differently than I would drive a vehicle with conventional brakes? Most of the time, under normal driving circumstances, there is no difference, and you should always drive with the same caution and care. It is important to realize that ABS only makes a difference when it is activated—when you have to brake hard—and that would only be when the computer senses that a wheel is approaching lock up. When ABS activates, keep steady pressure on the brake pedal and then let the ABS work for you. Don’t pump the brakes or try to ­find the threshold. Simply hold the brake pedal down and steer if necessary to avoid an obstacle.

Is ABS always active? ABS is always available, but not always activated. ABS is activated only when the brake pedal is applied and the computer detects an impending wheel lock condition.

Can older cars be retrofitted with ABS? No! The brake system is one of the most important features on any passenger vehicle. Several products, which tap into the master cylinder and/or brake system performance, are being sold in the aftermarket. Some of these products imply performance similar to new vehicle anti-lock brake systems. However, contrary to their claims, add-on systems, which deplete fluid from the master cylinder on brake apply may actually increase a vehicle’s stopping distance. This may cause the vehicle to fail to comply with Federal brake standards.

Does ABS always activate at the same speed? No, the system operates when the computer detects wheel lockup, at any speed above 8 mph.

Yes, in braking situations where the wheels on a non-ABS equipped vehicle would lock up, ABS will generally provide shorter controlled stopping distance. The amount of improvement in stopping distance depends on many factors, including the road surface, severity of braking, initial vehicle speed, etc. On some surfaces, such as gravel roads, braking distances can be longer, but you will still have the control benefits of ABS. The important capability of ABS is control. ABS provides improved vehicle steerability and stability when braking.

Will ABS wear out a vehicle’s brakes sooner?

What can affect the ABS advantage?

Do Federal Safety Standards mandate ABS?

It is important that you follow the maintenance schedule recommended in the owner’s manual of the vehicle, tires should be at their proper inflation level, the brake pads should be checked regularly, etc. While driving, you should sit comfortably, so that your hips are back in the seat and your knees are bent, even while braking. Your foot should be positioned so that your heel is on the floor and your toes are secure on the lower half of the pedal. And, though ABS may reduce stopping distance, remember: The faster you go, the longer it takes you to stop. Keeping a safe distance between you and the vehicle in front of you is always necessary, even with ABS.

A properly maintained brake system will be unaffected by ABS operation under typical driving conditions.

Are there different types of ABS? Yes, there are rear wheel anti-lock systems (RWAL) used on some trucks and four-wheel ABS available on cars and trucks.

No. Federal standards establish minimum braking performance requirements that all vehicles must meet, but do not specify how they should be met. It should be noted that even a vehicle with failed ABS meets the Federal safety standard for stopping distances.

Will a tire size change affect ABS? Use of tires other than original equipment may affect ABS performance. Owners should consult and follow the recommendations contained in the vehicle owner’s manual regarding replacement tire size. NOTE: ABS will work with original equipment spare tire or tire

What happens if ABS becomes inactive?

chains. However, performance is reduced.

The ABS electronic control unit has on-board diagnostic capability. If a fault is detected, the vehicle will revert to the base brake system, and the ABS telltale on the dash will be illuminated. Should this happen, the vehicle should be taken to a dealership for repair as soon as possible.

Do insurance companies give a discount for ABS?

How do I use ABS? Depress and hold the pedal. DO NOT PUMP THE BRAKES (that prevents the system from working). Just hold the brake pedal down and let the ABS work for you. You may feel the brake pedal vibrate, or you may notice some noise, but this is normal as the system works for you.

Yes, many insurance companies give discounts that range from 5% to 10%. In the states of New York and Florida all insurance companies are required to give an ABS discount of 5% on certain coverages such as bodily injury, property damage, collision, and personal injury protection. In other states the discount varies from insurance company to insurance company. When buying auto insurance, always ask your insurance agent if his/her company gives a discount for vehicles equipped with antilock brakes.

2014 Chevrolet Municipal Vehicles Technical Manual

Anti-lock braking system and Stabilitrak | 31

IMPORTANT DRIVING SAFETY TIPS A. A lways maintain a safe

following distance. ABS does not

allow you to stop on a dime. (Generally a 2-second following distance is considered safe in ideal conditions.) Watch the vehicle in front of you pass a fixed marker (such as a sign). Count seconds—one-thousand-one, one-thousand-two-until your front bumper reaches the marker. If you do not count out two seconds, then you are too close to the vehicle in front of you. Also, if the roads are wet or icy, or visibility is poor, you should increase your following distance.

B. A lways drive carefully—

especially on slippery surfaces. ABS cannot create friction between the tires and the road surface, it can only give the driver the maximum advantage of the existing adhesion. If the vehicle is traveling on a surface with no adhesion, the best ABS in the world cannot provide a shorter stopping distance or good steering.

C. It is a good idea to practice an

ABS activated stop and get the feel of the brake pedal. However, please make sure it’s at a safe time with no obstacles in your path. And you only really need to try it once or twice to know what happens.

Electronic Stability Control systems (StabiliTrak) Q. How does StabiliTrak work? StabiliTrak systems help drivers maintain control of their A. StabiliTrak has the ability to apply control forces to vehicles, especially during emergency lane changes or the vehicle independent of the driver. StabiliTrak uses avoidance maneuvers. StabiliTrak uses various sensors, sensors to continuously compare the path indicated by such as steering wheel angle, wheel speed, yaw velocity, the steering wheel position to the vehicle’s actual path. If etc., to detect any difference between the path requested a discrepancy is detected, StabiliTrak selectively controls by the steering wheel position and vehicle’s actual path. vehicle brakes and engine torque to create a yaw moment When appropriate, the system selectively controls brakes, that helps restore the vehicle’s actual path to the path engine power, and even suspension settings to enhance indicated by the steering wheel position. StabiliTrak has control of the vehicle’s direction and help keep it on course. the ability to help correct both understeer (where the Independent studies conducted by the National Highway vehicle is not turning as much as the steering wheel Traffic Safety Administration, the Insurance Institute for position indicates) and oversteer (where the vehicle is Highway Safety, and others have found StabiliTrak to be turning more than the steering wheel position indicates). highly effective in reducing vehicle crashes. General Motors The illustration at right shows how selective braking at a offers StabiliTrak systems on many of its passenger car particular wheel can create a compensating yaw moment and light truck models. to help restore the vehicle’s actual path to the path See your owner's manual for additional information about indicated by the steering wheel position. the operation of StabiliTrak. Q. Will a tire change affect StabiliTrak? Q. How do I use StabiliTrak? A. Use of tires other than original equipment may affect A. S  tabiliTrak operates independently of the driver. You StabiliTrak performance. StabiliTrak is designed to make should continue to drive your StabiliTrak equipped the best use of available traction. The performance vehicle with caution and care. GM’s StabiliTrak system, characteristics of the original equipment tires are part of StabiliTrak, is designed to be as seamless as possible in the overall system effectiveness. When you replace tires operation, to be part of the overall vehicle response and to check the recommendations in your owner's manual. On make a good vehicle better GM vehicles, the original equipment tires have a “TPC” (Tire Performance Criteria) code on the sidewall. Replacing the tires with the same “TPC” code will help assure proper StabiliTrak performance.

2014 Chevrolet Municipal Vehicles Technical Manual

32 | NOTES

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 2wd POLICE PACKAGE PPV | 1

Shown with aftermarket equipment

Shown with aftermarket equipment

Shown with aftermarket equipment

Updates for 2014

New Features

• Concord Metallic (GWU)

Deleted

• • • • • • • • •

Blue Ray Metallic (GXH) Black Granite Metallic (58U) Specialty Paint Wheatland Yellow (253A) Specialty Paint Dark Toreador Red (334D) Specialty Paint Dark Blue Metallic (722J) Specialty Paint Blue (5665) Specialty Paint Green (7941) Specialty Paint Woodland Green (9015) Specialty Paint Yellow (9414)

5. Gross Vehicle Weight Rating (GVWR). When properly equipped, includes vehicle, passengers, cargo and equipment. 6. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo.

2014 Chevrolet Municipal Vehicles Technical Manual

2 | Tahoe

2WD Police Package PPV

Police Package Option PPV must be ordered. The 2-wheel drive Tahoe Police Package is not intended for trailer towing. This vehicle has been designed for police work up to and including high speed emergency vehicle operations. GM restricts the sale of police vehicles and they are not to be sold to retail customers.

MODEL AVAILABILITY

CC10706

Rear-wheel drive

Warranty

3 years / 36,000 mile bumper-to-bumper (whichever comes first, see dealer for details) 5 years / 100,000 mile limited powertrain (whichever comes first, see dealer for details)

STANDARD EQUIPMENT SUMMARY INTERIOR FEATURES

Air conditioning

D ual-zone manual climate control with individual climate settings for driver and front passenger; includes auxiliary rear air conditioning and heat (rear operated from front control only) Assist handles Front passenger and second row outboard; front passenger assist handle is deleted when passenger side spotlamp is ordered Bluetooth Not available Compass Standard; displayed in Driver Information Center Console, floor Not available Console, overhead Includes map lamps Cruise control Electronic with set and resume speed DOME Lamps Dome lamps, cargo lamp with delayed entry feature and map lamps (see page 24 interior/exterior lamp control to turn off dome light) Floor covering Black vinyl floor and load floor behind second row seats Glass Deep tinted (all windows except light-tinted glass on windshield, driver and front passenger side glass) GLove box Locking door and no light Mirror Inside rearview manual day/night Navigation System Not available OnStar Not available Outside Temp. Display Standard; displayed in Driver Information Center Radio am/fm stereo with mp3 compatible cd player, seek-and-scan, digital clock, auto-tone control, Radio Data System (rds), speedcompensated volume and theftlock Restraint system Tahoe received an overall 5-star frontal and side crash test rating from NHTSA12. Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, rollover sensor, dual head curtain air bags1 for front and rear outboard occupants and front seat back mounted thorax-pelvic air bags1 Seats, front Cloth bucket seats, 6-way power driver and passenger seat adjusters with manual reclining seat back and lumbar controls and adjustable head restraints (see page 4) Seat, rear Vinyl split-folding 60/40 bench with outboard seating position headrests, 3rd seat not available (see page 4) Speedometer/cluster 140 mph certified analog speedometer, 1 mph increments and digital trip odometer with gauges for engine oil pressure, fuel, battery volts and coolant temperature. Driver Information Center displays engine hours, warnings and other information (see message listing on page 6) Stealth MODE See exterior lamps control on page 24 for operation description Steering wheel Tilt-wheel with column mounted gear shift lever Theft deterrent System  Vehicle PASS-Key® III+ and content theft (unauthorized entry, OR ENTRY WITHOUT USE OF KEYLESS REMOTE FOB, sounds horn and lamps flash). For Content Theft Alarm disable, option UTQ must be ordered (see page 7) Visors Padded with cloth trim, extends on rod; driver and front passenger illuminated vanity mirrors Warning toneS Headlamp on, key-in-ignition, driver and right-front passenger safety belt unfasten and turn signal on Window operation Power with driver express-down and lockout features Auxiliary power, front Auxiliary power, rear Ground studs Lock-out protection Power outlets Wiring diagrams

Electrical features

1 00-amp ignition and main power supply wiring at lower center of instrument panel (see wiring provisions for 12-volt battery power supply on page 23) 100-amp auxiliary power in cargo area (see page 23) Two studs located in rear compartment near bottom of liftgate opening (see page 23) Prevents the power door locks from locking the driver’s door if the keys are left in the ignition (manually lockable with engine running) Two located on instrument panel and one in rear cargo area See pages 28 through 31 for description; also see Tahoe Police Package owner’s manual supplement (located in glove box folder with standard owner’s manual)

Wiring Provision, EXTerior Lamps Flashing Forward lamp harness in-line connector for Exterior Lamps Flashing System (see option 6J7 on page 7) 1. H  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. 12. M  odel tested with standard head curtain side-impact air bags (SABs). Government 5-Star Safety ratings are part of the National Highway Traffic Safety Administration’s (NHTSA’s) New Car Assessment Program (www.SaferCar.gov).

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 2wd Police Package PPV | 3 Exterior Features Assist steps Body Side Moldings Defogger Door handles Door locks

Black, mounted between front and rear wheels Optional (see option B85 on page 7) Electric, rear window Matte Black Power, non-programmable with lockout protection and automatic door locking and unlocking, door lock cylinder no longer available on passenger front door and rear liftgate; child safety locks included in rear side doors Fascia, front Body color Fascia, rear Body color - with step pad Fog Lamps Not available Headlamps Dual halogen composite with flash-to-pass feature, automatic exterior lamp control and daytime running lamps (to delete automatic lamp control see option 9G8 on page 7) HORNS Dual note Keyless entry Includes two transmitters with non-functional panic button; stealth mode feature includes exterior lamps and horn disable; if remote start Option AP3 is included, running lamps will remain illuminated (additional transmitters are available; see option AMF on page 7) Keys Two-sided, random code, for ignition and driver door only Luggage rack Not available Mirrors Outside heated power-adjustable, manual-folding, Matte Black Rear liftgate Liftgate/liftglass with washer and wiper, and no lock cylinder on liftgate Recovery hooks Two front Under Hood Lamp Not available Windshield wipers Intermittent, wet-arm with flat blade and pulse washers

Chassis features

Air cleaner High-capacity Alternator 160-amp with idle boost (transmission in park or neutral) based on battery energy level Battery 660 CCA, 80-amp hour rating with battery rundown protection (does not protect customer installed equipment) Brakes Heavy-duty 4-wheel anti-lock front and rear disc with vacuum boost power assist Cooling Heavy-duty high capacity radiator, electric fans and extended life coolant; coolant hoses are EPDM (ethylene-propylene-diene monomer) rubber; silicone hoses are not required (coolant is DEX-COOL good for 5 years/150,000 miles, protects from -34° F to +265° F and against rust and corrosion) Engine Vortec 5300 V8 SFI with variable valve timing (VVT), active fuel management (AFM), FlexFuel2 (gasoline or E85 ethanol); top speed fuel cut-off at 139 mph; includes air conditioning wide open throttle cut off Frame Full perimeter, modular with hydroformed rails Fuel tank capacity 26 gallon (98 liters) Oil coolers Heavy-duty engine, transmission and auxiliary air-to-oil power steering (see page 23) Prop shaft Steel, 3.5 inch diameter Radio suppression Grounding straps, at five additional locations (see page 23 for locations) Skid plate Front underbody shield starting behind front bumper and running to 2nd cross-member protecting front underbody and oil pan Spark plugs Extended life - iridium tip Stabilitrak Stability enhancement system. An advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. Each time the vehicle is started, the StabiliTrak system is fully on. StabliliTrak can be controlled by a StabiliTrak button on the instrument panel located below the air conditioning fan control (see page 25). The condition of the system is displayed by an instrument panel StabiliTrak indicator light and Driver Information Center (DIC) Messages. Push once, Traction Control is off, push again and Traction Control and StabiliTrak are turned back on Steering Power, rack and pinion Suspension, front Coil-over-shock with stabilizer bar Suspension, rear Multi-link with coil springs, shocks and heavy-duty stabilizer bar Tires Goodyear P265/60R17 all-season, V-rated, blackwall Tire pressure monitor check tire pressure will display in driver message center, spare tire includes sensor; must be programmed when mounted (see page 18) Tire, spare Full-size spare, lockable with outside winch-type carrier mounted under frame at rear (includes TPM sensor - not programed) ­­Trailering equipment Not available on Police Package (ppv) ­­­­Traction control Deactivated when Police Performance Mode is engaged Transmission Enhanced calibration 6-speed automatic with overdrive, electronically-controlled transmission provides protection against overrevving the engine in low gear and a mechanical low gear blockout is not required; if a driver manually selects low gear and fails to manually upshift to high gear, the powertrain control module automatically protects the drivetrain ­­Wheels 17" x 7.5" heavy-duty black steel Wheel center cap Polished finish bolt-on metal 2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

4 | Tahoe

2WD Police Package PPV

POWERTRAIN

ENGINE TRANSMISSION AXLE OPTION

TYPE

DISPLACEMENT

CODE LITERS/CU. IN. LMG V8 5.3/325





EMISSIONS -

FUEL

OPTION

TYPE

SYSTEM CODE Active fuel MXO/MYC 6L80 management 6-speed FlexFuel2 auto. with OD (gas or E85 ethanol)

OPTION

RATIO

CODE GU4

3.08­­­

MUST BE SPECIFIED

FE9

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State YF5 California emissions. Use for ordering vehicles that will be registered in California. NE1 CT/ME/MD/MA/NJ/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8 Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Delaware, Massachusetts, Maryland, New Jersey, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State. NC7 Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/DE/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles” NB9 Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California. NOTE: T he 2014 Chevrolet Tahoe Police Patrol Vehicle and Special Service Vehicle with the 5.3L Engine (LMG) with Emission Option Codes NE1 and YF5 is certified to EPA Tier 2 Bin 4 standards and qualifies as ULEV (Ultra Low Emission Vehicle) under California Air Resources Board (CARB) requirements, meaning it is 50-state certified when ordered with NE1 or YF5. Emission Option Code FE9 (Federal) is Federal-only certified and not intended for registration in Arizona, California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State. Emission Standard: BIN4 (for Option Code NE1 or YF5), BIN5 (for Option Code FE9) EPA engine family or test group: EGMXT05.3381 (for Option Code NE1 or YF5), EGMXT05.3373 (for Option Code FE9)

TIRES MANUFACTURER

GOODYEAR

SPEED RATED

QUANTITY

SIZE

5

P265/60R17

SPEED RATING TYPE V

All season BW

NOTE:  Due to specific requirements for performance durability and safety, GM recommends only the original equipment tires for replacement Tire Plys = Tread: 2 Polyester, 2 Steel, 2 Nylon Sidewall: 2 Polyster Total 8 Ply T ire chains may be used with caution. See your owner's manual for specific recommendations regarding conditions. If the vehicle is equipped with a P265/60R17 tire size use tire chains only where legal and only when necessary. Use low profile chains that add no more than 12 mm thickness to the tire tread and inner sidewall. Use chains that are the proper size for the tires. Install them on the tires of the rear axle. Don't use chains on the tires of the front axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If the chains contact the vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage the vehicle.

SEATS AND INTERIOR TRIM STANDARD Front: cloth bucket with NO center console (power driver and passenger) Rear: vinyl 60/40 split-bench OPTIONAL Front: cloth 40/20/40 split-bench (power driver side seat only) Rear: vinyl 60/40 split-bench

SEAT OPTIONS EBONY A95 and 9N5 19C 5T5 AZ3 19C 5T5

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 2wd Police Package PPV | 5 AVAILABLE EXTERIOR COLORS GWT

GHA

89U

GAN

41U

GWU

50U

Champagne Silver Metallic

Mocha Steel Metallic

Crystal Red* Tintcoat

Silver Ice Metallic

Black

Concord Metallic (New)

Summit White



Actual colors may vary

* Additional Charge

SEO Paint Available WA#

COLOR DESCRIPTION

9260 Victory Red

SEO CODE



5T4

Actual Color May VAry

NOTE: • All normally body-colored non-sheet metal parts • SEO paint orders that contain less than five vehicles will be delayed until five unit minimum is received for batch production

2014 Chevrolet Municipal Vehicles Technical Manual

6 | Tahoe

Police PPV DRiver Information center

United States Certified Speedometer/cluster (CANADIAN SIMILAR)

MessaGe Center

change engine oil soon

replace battery in remote key

check tire pressure (press reset) lf/rf/lr/rr

right rear door open

Driver DOor open

service battery charging system

engine hot a/c turned off

engine hours

engine oil low add oil

service brake system

engine overheated idle engine

service brakes soon

engine overheated Stop engine

service theft deterrent system

engine power is reduced

service tire monitor system

fuel level low

tighten gas cap

hood open

tire learning active

left rear door open

traction control off

oil pressure low stop engine

Transmission Hot Idle Engine

passenger door open

Turn signal on

rear access open

Washer Fluid Low add Fluid

remote key learning active NOTE: T he Tahoe Police Package and Special Service Package are not equipped with dic buttons. The instrument cluster odometer trip stem is used to display the following messages: odometer, engine hours, trip odometer, tire pressure, remote keyless entry, relearn remote key, programming  and dic language. See the Tahoe owner’s manual for operation description.

service air bag

SPEEDOMETER CERTIFICATION 2014 Tahoe police vehicle certified speedometer calibration. Specifications at ambient temperature of -10 to 120 degree F. Inaccuracies due to vehicle speed sensing are included. Actual vehicle speed indicated speed 0 to 120 mph +/- 2 MPH The speedometer calibration is for the 5.3L engine, automatic transmission with a 3.08 axle and P265/60R17 V-rated tires

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 2wd Police Package PPV – Options | 7 Available options WITH Tahoe PPV Police PACKAGE K5T batteries dual - 660 CCA, 80-amp hour rating, parallel connected B85 body side moldings - On 4 doors 1LR Brake System, City - Uses base friction material that wears better at lower temperatures and city service. The city brakes are not optimal for track performance. The rotor does not have the radial drilled holes. The parts are physically interchangeable for service, however the parts should be substituted as complete four wheel sets Utq content theft alarm disable - Flashing lamps and horn warning (This option is recommended for customers that do not intend on using keyless entry remote fobs) 9g8 delete daytime running lamps and automatic headlamps - Exterior lamps are operated manually (see page 24 for description) 5t4 exterior body colored parts - Victory Red special painted exterior body parts in lieu of glossy Black color normally installed with special painted bodies, Victory Red painted parts will consist of front fascia, rear bumper fascia, rear liftgate license plate applique and rear liftgate handle, door handles and body side moldings. Mirrors, rear D-pillar applique and liftgate spoiler will remain Black. Requires SEO TGK special paint and special paint color WA9260 Victory Red. Includes RPO B85 body side moldings 6j7 flasher system headlamps and tail lamps - drl compatible, headlamp flasher module with control wire and body control module rear lamp flashing (see page 27) B30 floor covering - Color keyed carpeting (includes rear cargo floor) B58 floor mats - Color keyed carpeted front and 2nd row (not available with vinyl floor covering) K05 heater - Engine block Ppv identifier - Police Package 6e2 key common - Complete vehicle fleet, provides a single key cut with a specific code that is common to the door lock and ignition of all the vehicles in the vehicle fleet; this key code is an alternate to SEO 6e8 key common, complete vehicle fleet; not compatible with 2005 and earlier Impalas, 2006 and earlier Tahoes and 2011 and later Caprice 6e8 key common - Complete vehicle fleet, provides a single key cut with a specific code that is common to the door lock and ignition of all the vehicles in the vehicle fleet; this key code is an alternate to SEO 6e2 key common, complete vehicle fleet; not compatible with 2005 and earlier Impalas, 2006 and earlier Tahoes and 2011 and later Caprice AMF Keyless entry transmitters - Fleet Package includes 6 additional transmitters. Transmitters are not programmed. Each transmitter, including the two standard with the vehicle, must be programmed together by a dealer at customer expense. Transmitter programming is not a warranty item. See also your owner's manual supplement for programming information. (see also page 25 for customer programming of transmitters using the vehicle Driver Information Center procedure) NOTE: Vehicle specific, common fleet transmitter frequency not available G80 locking differential - Heavy-duty ­Trw provision for roof mounted lamp - Overhead console mounted switch and wiring to the roof; upfitter to install and connect a roof mounted warning lamp; instructions provided in owner’s manual supplement (see page 25) 6n6 Rear door LockS inoperative - Rear power locks are inoperable at rear door but operate from drivers position (see page 25) 6b2 rear door handles inoperative - Rear door inoperative; doors can be opened only from outside (see page 25) 6n5 rear Door window switches inoperative - Rear windows only operate from drivers position (see page 25) Ap3 remote vehicle starter system - Includes remote keyless entry 5t5 seats - Front cloth with vinyl rear seat (see page 4) TGK SPECIAL PAINT SOLID - One color all normally body-colored non-sheet metal parts will be gloss Black. This includes front and rear facias, liftgate handle and applique, D-pillars and upper liftgate applique. Mirrors and door handles will be grained Black parts. B85 body-side moldings are not available except with SEO option 5T4 exterior body-colored parts. May require extended lead time. Required with any SEO paint selection. May require extended lead time 7x6 spotlamp - Left hand, separately fused (see page 26) 7x7 spotlamps - Left and right hand, separately fused (see page 26) Wx7 wiring - For customer connection to front door and windshield pillar speakers. Front speakers are not connected to the vehicle radio; radio audio signals are routed to the rear speakers (see page 26) 6j3 wiring - For grille lamps and siren speaker. (see page 27) 6j4 wiring - For horn/siren circuit, in-line connection for customer furnished switch (see page 26) Autonet Mobile WiFi in-car router - Available through your GM Dealer (see page 26)

For standard and optional illustrations see pages 23 through 27 2014 Chevrolet Municipal Vehicles Technical Manual

8 | Tahoe

2WD Police Package PPV – Specifications

GENERAL

ENGINE

Model Drive

CC10706 2-wheel

EXTERIOR (in./mm) Wheelbase Overall length Overall width Overall height* Lift in height (load floor to ground) Step height - (front door sill to ground) Step height - (rear door sill to ground) Step height - (front running board to ground) Step height - (rear running board to ground) Front track width Rear track width Turning diameter curb to curb (ft./m) Ground clearance* (rear axle)

116.0/2946 202.0/5131 79.0/2007 73.9/1877 30.3/770 20.4/517 20.8/528 12.1/307 12.5/317 68.2/1732 67.0/1701 39.0/11.9 8.0/203

FRONT COMPARTMENT (in./mm) Head room Shoulder room Hip room Leg room

REAR COMPARTMENT (in./mm) 39.2/996 65.2/1656 60.6/1539 39.0/991

CARGO Load floor length to center of front seat at floor (in./mm) Load floor length to center of 2nd seat at floor (in./mm) Inside width between wheel house (in./mm) Cargo area height (in./mm) Cargo volume3 maximum behind front seat (cu. ft./liters) Cargo volume3 maximum behind second seat (cu. ft./liters)

81.4/2068 49.4/1255 49.1/1247 41.7/1059 108.9/3084 60.3/1707

NOTE: For additional dimensional data go to: gmupfitter.com

PASSENGER COMPARTMENT VOLUME INDEX (cu.ft./liters) Passenger compartment volume index3

Fuel Economy Ratings

121.8/ 3449

CITY/HIGHWAY/COMBINED

5.3L engine 2WD4

15/21/17

Projected EPA label values, actual mileage will vary with options, driving conditions, driving habits and vehicle’s condition.

ALTERNATOR Type Amps

77°F (25°C)

Tahoe POLICE ALTERNATOR OUTPUT

TRANSMISSION Automatic electronic with overdrive Fluid pan removed and filter replaced (quarts/liters)

6-speed 6.0/5.7

AXLE Ratio

41.1/1044 65.2/1656 60.3/1532 41.3/1049

Head room Shoulder room Hip room Leg room

STD Vortec V8 5.3/325 320 @ 5400 335 @ 4000 sfi 9.9:1 Single 87 26/98 6.0/5.7 18.3/17.3

Type Displacement: liters/cu. in. Horsepower/rpm Torque lb.-ft./rpm Induction system Compression ratio Exhaust Minimum recommended fuel octane Fuel tank capacity (gallons/liters) Oil with filter (quarts/liters) Cooling capacity (quarts/liters)

REMY DR44M 160

3.08

BRAKES ABS with vacuum-boost Front-swept area (sq. in./sq. cm) Rear-swept area (sq. in./sq. cm) Total front and rear swept area (sq. in./sq. cm) Front rotor diameter (in./mm) Rear rotor diameter (in./mm) Front rotor thickness (in./mm) Rear rotor thickness (in./mm)

Disc/Disc 256.6/1655 248/1600 504.6/3255 13.0/330 13.5/343 1.2/30 .79/20

TIRES Type Size

Goodyear V-rated all-season P265/60R17

WHEELS Type Size

Steel 17" x 7.5"

CHASSIS Frame Front suspension Rear suspension Steering type Steering ratio

Full perimeter steel Independent, single coil-over-shocks with stabilizer bar Multi-link with coil spring Power rack and pinion 17.75:1

BATTERY Type BCI group size Volts Amp hour rating Cold cranking-amps @ 0°F (-18°C) Reserve capacity @ 80°F (27°C)

Maintenance free LN3 12 80 660 135 minutes

Vehicle Weight (lbs./kg.) GVWR5 Curb weight10 Payload6 with bucket seats

6800/3084 5285/2397 1516/688

NOTE: See owner’s manual supplement for loading information

NORMAL IDLE SPEED: 600-650 RPMS COMPUTER CONTROLLED IDLE SPEED RANGE (PARK): 800-1000 RPM

3. Cargo and load capacity limited by weight and distribution. 4. EPA-estimated MPG. 5. Gross Vehicle Weight Rating (GVWR). When properly equipped, includes vehicle, passengers, cargo and equipment. 6. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo. 10. Curb weight in operational status with 100% fuel, fluids and standard base equipment (excludes optional content) * Published dimensions indicated are at curb weight

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe Police PPV and special services Dimensions | 9 TAHOE POLICE PPV AND SPECIAL SERVICE PACKAGE

10 | Tahoe

Police PPV – Vehicle load limits

This information is intended for those who intend to install additional equipment to the police vehicle after it has left the factory, and for those who will be driving and loading the vehicle with passengers and/or cargo. Two labels on your vehicle show how much weight it was designed to carry, the Tire and Loading Information label and the Certification/Tire label. These labels are attached to your vehicle and give you the maximum load capacity, the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for your vehicle. See "Vehicle Load Limits" in the owner manual Index for additional loading information. The following guidelines can help you with proper loading and load distribution when installing additional equipment on the TahoePolice Package. WARNING Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). This can cause systems to break and change the way the vehicle handles. This could cause loss of control and a crash. Overloading can also shorten the life of the vehicle. Adding Equipment to Your Vehicle Before adding accessories or equipment to your police vehicle, there are some things you need to know • The police vehicle's maximum capacity weight (payload). The weight of your police vehicle, including a full tank of fuel but without a driver and passengers. • The weight of items you plan on adding to your police vehicle, like roof mounted light bar(s), push bumpers, security barrier(s), rear storage organizer, highway flares, fire extinguishers, weapons, ammunition, radios, and video equipment. • The weight and number of passengers you intend to carry in your vehicle. • The total weight of any additional cargo you intend to carry in your vehicle. When planning your vehicle equipment installation remember not to exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) of the front or rear axles. To keep the available load weight less than the vehicle capacity weight, you may need to limit the number of passengers you carry in your vehicle or change your choice of additional equipment. Center of Gravity (CG) A vehicle's center of gravity is an imaginary location inside the vehicle and is a balance point for the vehicle mass as it moves down the road. The police vehicle's center of gravity, before you add a load and passengers, is approximately midway between the center of the axles, up from the ground to just below the front window, and between the driver and passenger. Equipment location and weight on the vehicle's center of gravity is important to keep in mind when planning an installation. Heavy equipment should be positioned as low and as far forward in the rear load compartment as possible. Try to mount the equipment below the bottom of the side windows. Refer to the Loading Zone chart and diagram to help with your installation plan. A procedure to make the necessary measurements and formulas to calculate the vehicle longitudinal, lateral and vertical position of the center of gravity can be found in the GM Coachbuilders Manual. Equipment required to conduct the measurements for calculating the center of gravity are: • Weight scales of sufficient capacity to measure the vehicle weight at each wheel. • A post type hoist or other means to safely elevate the front of the vehicle to at least an angle of 20 degrees above horizontal. See your GM dealer to get more information about this coachbuilder procedure. Keeping the center of gravity midway between the axles is also important to provide proper braking performance. About half the total vehicle weight on each axle is recommended. Weigh your vehicle after the additional equipment has been installed to determine the actual weight of your vehicle. Weigh the vehicle with a full tank of fuel and without passengers. You may need to put a limit on how many people or other equipment you can carry inside your vehicle after the additional equipment has been installed.

Note: See loading zone weight chart and diagram on page 11

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe Police PPV – Loading Zones | 11

Loading zone for customer installed equipment and cargo without passengers

Shown without optional body side moldings

Loading Zone Weight Chart – Tahoe Police Package (PPV)

37 lbs (17 kg)

51 lbs (23 kg)

88lbs (40 kg)

133 lbs (60 kg)

529 lbs (240 kg)

662 lbs (300 kg)

170 lbs (77 kg)

580 lbs (263 kg)

750 lbs (340 kg)

2014 Chevrolet Municipal Vehicles Technical Manual

12 | NOTES

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 4wd Special Service – 5W4 | 13

Shown with aftermarket equipment

Shown with aftermarket equipment

Shown with optional bucket seats

Updates for 2014

New Features

• Concord Metallic (GWU)

Deleted

• • • • • • • • •

Blue Ray Metallic (GXH) BLACK GRANITE METALLIC (58U) Specialty Paint Wheatland Yellow (253A) Specialty Paint Dark Toreador Red (334D) Specialty Paint Dark Blue Metallic (722J) Specialty Paint Blue (5665) Specialty Paint Green (7941) Specialty Paint Woodland Green (9015) Specialty Paint Yellow (9414)

2014 Chevrolet Municipal Vehicles Technical Manual

14 |

Tahoe 4wd Special Service – 5W4 NOTE: This vehicle is NOT designed nor intended for use IN HIGH SPEED EMERGENCY VEHICLE OPERATIONS GM restricts the sale of police vehicles and they are not to be sold to retail customers.

MODEL AVAILABILITY CK10706

4-wheel drive

Warranty

3 years / 36,000 mile bumper-to-bumper (whichever comes first, see dealer for details) 5 years / 100,000 mile limited powertrain (whichever comes first, see dealer for details)

STANDARD EQUIPMENT SUMMARY INTERIOR FEATURES Air conditioning

D ual-zone manual climate control with individual climate settings for driver and front passenger; includes auxiliary rear air conditioning and heat (rear operated from front control only) Assist handles Front passenger and second row outboard; front passenger assist handle is deleted when passenger side spotlamp is ordered Bluetooth Not available Compass Standard; displayed in Driver Information Center Console, overhead Includes map lamps Cruise control Electronic with set and resume speed DOME Lamps Dome lamps, cargo lamp with sustained lamps feature and map lamps (see page 24 interior/exterior lamp control to turn off dome light) Floor covering Black vinyl floor and load floor behind second row Glass Deep tinted (all windows except light-tinted glass on windshield, driver and front passenger side glass) GLove box Locking door, no light Mirror Inside rearview manual day/night Navigation System Not available OnStar Not available Outside Temp. Display Standard; displayed in Driver Information Center Radio am/fm stereo with mp3 compatible cd player, seek-and-scan, digital clock, auto-tone control, Radio Data System (rds), speedcompensated volume and theftlock Restraint system Tahoe received an overall 5-star frontal and side crash test rating from NHTSA12. Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, rollover sensor, dual head curtain air bags1 for front and rear outboard occupants and front seat back mounted thorax-pelvic air bags1 Seat, front Cloth 40/20/40 split-bench 3-passenger, includes 6-way power driver seat adjuster (power passenger seat is not available) with manual lumbar, driver and passenger manual reclining, outboard head restraints, center fold-down storage armrest and rear storage pockets (see page 14). Bucket seats available, see A95 page 17 Seat, rear Vinyl split-folding 60/40 bench with outboard seating position headrests, 3rd seat not available (see page 14) Speedometer/cluster 120 mph analog speedometer and digital trip odometer with gages for engine oil pressure, fuel, battery volts and coolant temperature. Driver Information Center displays engine hours, warnings and other information (see message listing on page 16) Stealth MODE See exterior lamps control on page 24 for operation description Steering wheel Tilt-wheel with column mounted gear shift lever Theft deterrent System Vehicle PASS-Key® III+ and content theft (unauthorized entry sounds horn and lamps flash). For Content Theft Alarm disable option utq must be ordered (see page 19) Visors Padded with cloth trim, extends on rod; driver and front passenger illuminated vanity mirrors Warning toneS Headlamp on, key-in-ignition, driver and right-front passenger safety belt unfasten and turn signal on Window operation Power with driver express-down and lockout features

Electrical features Auxiliary power, front Auxiliary power, rear Ground studs Lock-out protection Power outlets Wiring diagrams

1 00-amp ignition and main power supply wiring at lower center of instrument panel (see wiring provisions for 12-volt battery power supply on page 23) 100-amp auxiliary power in cargo area (see page 23) Two studs located in rear compartment near bottom of liftgate opening (see page 23) Prevents the power door locks from locking the driver’s door if the keys are left in the ignition (manually lockable with engine running) Two located on instrument panel and one in rear cargo area See pages 28 through 31 for description; also see Tahoe Police Package owner’s manual supplement (located in glove box folder with standard owner’s manual)

Wiring PROVISION, EXTerior Lamps Flashing Forward lamp harness in-line connector for Exterior Lamps Flashing System (see option 6J7 on page 19) 1. H  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. 12. M  odel tested with standard head curtain side-impact air bags (SABs). Government 5-Star Safety ratings are part of the National Highway Traffic Safety Administration’s (NHTSA’s) New Car Assessment Program (www.SaferCar.gov).

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 4wd Special Service – 5W4 | 15 Exterior Features Assist steps Body Side Moldings Defogger Door handles Door locks

Black, mounted between front and rear wheels Optional (see option B85 on page 19) Electric, rear window Matte Black Power, non-programmable with lockout protection, and automatic door locking and unlocking, door lock cylinder no longer available on passenger front door and rear liftgate; child safety locks included in rear doors Fascia, front Color - keyed Fascia, rear Color - keyed with step pad Fog Lamps Not available Headlamps Dual halogen composite with flash-to-pass feature, automatic exterior lamp control and daytime running lamps (to delete automatic lamp control, see option 9G8 on page 17) Horns Dual note Keyless entry Includes two transmitters with non-functional panic button; stealth mode feature includes exterior lamps and horn disable; if remote start Option AP3 is included, running lamps will remain illuminated (additional transmitters are available; see option AMF on page 19) Keys Two-sided random code, for ignition and driver door only Luggage rack Not available Mirrors Outside heated power-adjustable, manual-folding, Matte Black Rear liftgate Liftgate/liftglass with washer and wiper, power liftgate not available and no lock cylinder on liftgate Recovery hooks Two front Under Hood Lamp Not available Windshield wipers Intermittent with washer

chassis Features Air cleaner High-capacity Alternator 160-amp with idle boost (transmission in park or neutral) based on battery energy level Battery 660 CCA, 80-amp hour rating with battery rundown protection (does not protect customer installed equipment) Brakes 4-wheel anti-lock front and rear disc with vacuum boost power assist Cooling Heavy-duty high capacity radiator, electric fans and extended life coolant; coolant hoses are EPDM (ethylene-propylene-diene monomer) rubber; silicone hoses are not required (coolant is DEX-COOL good for 5 years/150,000 miles, protects from -34° F to +265° F and against rust and corrosion) Engine Vortec 5300 V8 SFI with variable valve timing (VVT), active fuel management (AFM), FlexFuel2 (capable of running on gasoline or E85 ethanol; mixtures) top speed fuel cutoff at 98 MPH Frame Full perimeter modular with hydroformed frame rails Fuel tank capacity 26 gallon (98 liters) Oil coolers Engine and transmission auxiliary air-to-oil and power steering (see page 24 for description) Radio suppression Grounding straps at five additional locations (see page 23 for location) Spark plugs Extended life - iridium tip Stabilitrak Stability enhancement system. An advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. Each time the vehicle is started, the StabiliTrak system is fully on. StabliliTrak can be controlled by a StabiliTrak button on the instrument panel located below the air conditioning fan control (see page 24). The condition of the system is displayed by an instrument panel StabiliTrak indicator light and Driver Information Center (DIC) Messages. Push once, Traction Control is off, push and hold five seconds Traction Control and StabiliTrak is off, push again and Traction Control and StabiliTrak are turned back on Steering Power, rack and pinion Suspension, front Coil-over-shock with stabilizer bar Suspension, rear Multi-link with coil springs with stabilizer bar Tires P265/70R17 all-season SBR Tire pressure monitor check tire pressure will display in driver message center (no spare tire sensor) Tire, spare Full-size spare, lockable with outside winch-type carrier mounted under frame at rear (TPM sensor not included) Trailering equipment Heavy-duty, includes trailering hitch platform, 7-wire harness with independent fused trailering circuits mated to a 7-way sealed connector, vr4 2-inch trailering receiver and electric brake controller jumper harness Transfer case Electronic autotrac Transmission 6-speed automatic with overdrive and tow/haul mode, electronically-controlled transmission provides protection against over-revving the engine in low gear and a mechanical low gear blockout is not required; if a drive­­­r manually selects low gear and fails to manually upshift to high gear, the powertrain control module automatically protects the drivetrain Wheels 17" x 7.5" argent steel Wheel center cap Argent, retained to wheel lugnuts 2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

16 | Tahoe

4wd Special Service – 5W4

POWERTRAIN

ENGINE TRANSMISSION AXLE OPTION

TYPE

DISPLACEMENT

CODE LITERS/CU. IN. LMG V8 5.3/325





EMISSIONS -

FUEL

OPTION

TYPE

SYSTEM CODE Active fuel MXO/MYC 6L80 management 6-speed FlexFuel2 auto. with OD (gas or E85 ethanol)

OPTION

RATIO

CODE GU6

3.42­­­

MUST BE SPECIFIED

FE9

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State YF5 California emissions. Use for ordering vehicles that will be registered in California. NE1 CT/ME/MD/MA/NJ/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8 Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Delaware, Massachusetts, Maryland, New Jersey, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State. NC7 Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/DE/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles” NB9 Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California. NOTE: T he 2014 Chevrolet Tahoe Police Patrol Vehicle and Special Service Vehicle with the 5.3L Engine (LMG) with Emission Option Codes NE1 and YF5 is certified to EPA Tier 2 Bin 4 standards and qualifies as ULEV (Ultra Low Emission Vehicle) under California Air Resources Board (CARB) requirements, meaning it is 50-state certified when ordered with NE1 or YF5. Emission Option Code FE9 (Federal) is Federal-only certified and not intended for registration in Arizona, California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State. Emission Standard: BIN4 (for Option Code NE1 or YF5), BIN5 (for Option Code FE9) EPA engine family or test group: EGMXT05.3381 (for Option Code NE1 or YF5), EGMXT05.3373 (for Option Code FE9)

TIRES Manufacturer

Random

SPEED RATED

QUANTITY

SIZE

5

P265/70R17

SPEED RATING TYPE S

All season BW

NOTE:  Optional on/off-road tire is available (see option 4JP on page 19) Tire Plys = Tread: 2 Polyester, 2 Steel, 1 Nylon Sidewall: 2 Polyster Total 7 Ply Tire chains may be used with caution. See your owner's manual for specific recommendations regarding conditions. If the vehicle is equipped with a P265/60R17 tire size use tire chains only where legal and only when necessary. Use low profile chains that add no more than 12 mm thickness to the tire tread and inner sidewall. Use chains that are the proper size for the tires. Install them on the tires of the rear axle. Don't use chains on the tires of the front axle. Tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer's instructions. If the chains contact the vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage the vehicle.

SEATS AND INTERIOR TRIM

STANDARD Front: cloth 40/20/40 split-bench (power driver side seat only) Rear: vinyl 60/40 split-bench OPTIONAL Front: cloth buckets with center console (power driver and passenger seat) Rear: vinyl 60/40 split-bench OPTIONAL Front: cloth buckets without center console (power driver and passenger seat) Rear: vinyl 60/40 split-bench

SEAT OPTIONS EBONY AZ3 19C 5T5 A95 19C 5T5 A95 and 9N5 19C 5T5

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 4wd Special Service – 5W4 | 17

AVAILABLE EXTERIOR COLORS GWT

GHA

89U

GAN

41U

GWU

50U

Champagne Silver Metallic

Mocha Steel Metallic

Crystal Red* Tintcoat

Silver Ice Metallic

Black

Concord Metallic (New)

Summit White



Actual colors may vary

* Additional Charge

SEo Paint Available WA#

COLOR DESCRIPTION

9260 Victory Red

CODE

5T4

Actual Color May VAry NOTE: • All normally body-colored non-sheet metal parts • SEO paint orders that contain less than five vehicles will be delayed until five unit minimum is received for batch production

2014 Chevrolet Municipal Vehicles Technical Manual

18 |

Tahoe 4wd 5W4 – DRiver Information center United States Speedometer/cluster (CANADIAN SIMILAR)

MessaGe Center

change engine oil soon

service air bag

check tire pressure (press reset) lf/rf/lr/rr

service battery charging system

Driver Door Open

service brake system

engine hot a/c turned off

service brakes soon

engine oil low add oil

service theft deterrent system

engine overheated idle engine

service tire monitor system

engine overheated stop engine

service traction control

engine power is reduced

Service stabilitrak

fuel level low

stabilitrak off

hood open

ServIce 4-Wheel drive

left rear door open

tighten gas cap

oil pressure low stop engine

tire learning active

passenger door open

traction control off

rear access open

transmission hot idle engine

remote key learning active

turn signal on

replace battery in remote key

Washer Fluid low add Fluid

engine hours

right rear door open NOTE: T he Tahoe Police Package and Special Service Package are not equipped with dic buttons. The instrument cluster odometer trip stem is used to display the following messages: odometer, engine hours, trip odometer, tire pressure, remote keyless entry, relearn remote key, programming  and dic language. See the Tahoe owner’s manual for operation description.

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe 4wd Special Service 5W4 – OptionS | 19 AVAILABLE OPTIONS WITH Tahoe 5W4 SPECIAL SERVICE PACKAGE

batteries, dual - 660 CCA, 80-amp hour rating, parallel connected body side moldings - On 4 doors brake controller - Integrated trailer chassis package off-road suspension - (Requires qjp tire and includes nzz skid plates, k47 high capacity air cleaner, no z71 decal) console delete - Between seats (Requires a95) content theft alarm disable - Flashing lamps and horn warning delete daytime running lamps and automatic headlamps - Exterior lamps are operated manually (see page 24) exterior body colored parts - Victory Red special painted exterior body parts in lieu of glossy Black color normally installed with special painted bodies, Victory Red painted parts will consist of front fascia, rear bumper fascia, rear liftgate license plate applique and rear liftgate handle, door handles and body side moldings. Mirrors, rear D-pillar applique and liftgate spoiler will remain Black. Requires SEO TGK special paint and special paint color WA9260 Victory Red. Includes RPO B85 body side moldings 6j7 flasher system headlamps and tail lamps - DRL compatible, headlamp flasher module with control wire and body control module rear lamp flashing (see page 27) B30 floor covering - Color keyed carpeting (includes rear cargo floor) B58 floor mats - Color keyed carpeted front and 2nd row (not available with vinyl floor covering) K05 heater - Engine block 5W4 identifier - Special Service Package 6e2 key common - Complete vehicle fleet, provides a single key with a specific code that is common to the door lock and ignition of all the vehicles in the vehicle fleet; key code is an alternate to SEO 6e8 key common, complete vehicle fleet; not compatible with 2005 and earlier Impalas, 2006 and earlier Tahoes and 2011 and later Caprice 6e8 key common - Complete vehicle fleet, provides a single key with a specific code that is common to the door lock and ignition of all the vehicles in the vehicle fleet; key code is an alternate to SEO 6e2 key common, complete vehicle fleet; not compatible with 2005 and earlier Impalas and 2006 and earlier Tahoes and 2011 and later Caprice AMF Keyless entry transmitters - Fleet Package includes 6 additional transmitters. Transmitters are not programmed. Each transmitter, including the two standard with the vehicle, must be programmed together by a dealer at customer expense. Transmitter programming is not a warranty item. See also your owner's manual supplement for programming information. (see also page 25 for customer programming of transmitters using the vehicles Driver Information Center procedure) NOTE: Vehicle specific, common fleet transmitter frequency not available G80 locking differential Trw provision for roof mounted lamp - Overhead console mounted switch and wiring to the roof; upfitter to install and connect a roof mounted warning lamp; instructions provided in owner’s manual supplement (see page 25) 6b2 rear door handles inoperative - Rear door inoperative; doors can be opened only from outside (see page 25) 6n6 Rear door locks inoperative - Rear power locks are inoperable at rear doors but operate form drivers position (see page 25) 6n5 rear door window switches inoperative - Rear window only operates from driver’s position (see page 25) Ap3 remote vehicle starter system - Includes remote keyless entry Az3 seats - Front custom cloth 40/20/40 split-bench, power driver seat only (see page 16) A95 seats - Front bucket with custom cloth, 6-way power with center console, to delete center floor console 9n5 must be ordered (see page 16) 5t5 seats - Front cloth with vinyl rear seat ­­(see page 16) Nzz skid plates package TGK SPECIAL PAINT SOLID - One color all normally body-colored non-sheet metal parts will be gloss Black. This includes front and rear facias, liftgate handle and applique, D-pillars and upper liftgate applique. Mirrors and door handles will be grained Black parts. B85 body-side moldings are not available except with SEO option 5T4 exterior body-colored parts. May require extended lead time. Required with any SEO paint selection. May require extended lead time 7x6 spotlamp - Left hand, separately fused (see page 26) 7x7 spotlamp - Left and right hand, separately fused (see page 26) ­­­­­­­­­4JP tire SPare - P265/70R17 on/off-road, blackwall (requires QJP tires) Qjp tires - P265/70R17 on/off-road (for full-size spare tire 4JP must be ordered) P46 wheels - Aluminum Wx7 wiring - For customer connection to front door and windshield pillar speakers. Front speakers are not connected to the vehicle radio; radio audio signals are routed to the rear speakers (see page 26) 6j3 wiring - For grille lamps and siren speaker (see page 27) 6j4 wiring - For horn/siren circuit, in-line connection for customer furnished switch (see page 26) Autonet Mobile WiFi in-car router - Available through your GM Dealer (see page 26)

K5T B85 Jl1 9g3 9n5 Utq 9g8 5t4

For standard and optional illustrations see pages 23 though 27

2014 Chevrolet Municipal Vehicles Technical Manual

20 | Tahoe

GENERAL

4wd Special Service 5W4 – Specifications ENGINE

Model Drive

CK10706 4-wheel

EXTERIOR (in./mm)

Wheelbase Overall length Overall width Overall height* Lift in height (load floor to ground) Step height - (front door sill to ground) Step height - (rear door sill to ground) Step height - (front running board to ground) Step height - (rear running board to ground) Front track width Rear track width Turning diameter curb to curb (ft./m) Ground clearance* - (front axel) Ground clearance* - (rear axel)

116.0/2946 202.0/5131 79.0/2007 76.9/1953 32.6/828 22.3/567 22.8/580 14.0/356 14.5/369 68.2/1732 67.0/1701 39.0/11.9 10.5/266.7 9.1/231

FRONT COMPARTMENT (in./mm) Head room Shoulder room Hip room Leg room

41.1/1044 65.2/1656 60.3/1532 41.3/1049

REAR COMPARTMENT (in./mm) Head room Shoulder room Hip room Leg room

39.2/996 65.2/1656 60.6/1539 39.0/991

CARGO Load floor length to center front seat at floor (in./mm) Load floor length to center 2nd seat at floor (in./mm) Inside width between wheel house (in./mm) Cargo area height (in./mm) Cargo volume3 maximum behind front seat (cu. ft./liters) Cargo volume3 maximum behind second seat (cu. ft./liters)

81.4/2068 49.4/1255 49.1/1247 41.7/1059 108.9/3084 60.3/1707

Type Displacement: liters/cu. in. Horsepower/rpm Torque lb.-ft./rpm Induction system Compression ratio Exhaust Minimum recommended fuel octane Fuel tank capacity (gallons/liters) Oil with filter (quarts/liters) Cooling capacity (quarts/liters)

TRANSMISSION Automatic electronic with overdrive Fluid pan removed and filter replaced (quarts/liters) Ratio 4-wheel drive ABS with vacuum boost Front - swept area (sq. in./sq. cm) Rear - swept area (sq. in./sq. cm) Total front and rear swept area (sq. in./sq. cm) Front rotor diameter (in./mm) Rear rotor diameter (in./mm) Front rotor thickness (in./mm) Rear rotor thickness (in./mm) Type Size

CITY/HIGHWAY/COMBINED 15/21/17

Projected EPA label values, actual mileage will vary with options, driving conditions, driving habits and vehicles condition.

ALTERNATOR Type Amps

77°F (25°C)

REMY DR44M 160

Tahoe POLICE ALTERNATOR OUTPUT

S-Rated All Season P265/70R17

WHEELS

CHASSIS

5.3L engine 4WD4

Disc/Disc 256.6/1655 248/1600 504.6/3255 13.0/330 13.5/343 1.2/30 .79/20

TIRES

Passenger compartment volume index3

Fuel Economy Ratings

3.42

BRAKES

Type Size

121.8/ 3449

6-speed 6.0/5.7

AXLE

PASSENGER COMPARTMENT VOLUME INDEX (cu.ft./liters)

NOTE: For additional dimensional data go to: gmupfitter.com

Vortec V8 5.3/325 320 @ 5400 335 @ 4000 sfi 9.9:1 Single 87 26/98 6.0/5.7 18.3/17.3

Frame Front suspension Rear suspension Steering type Steering ratio

Steel S-Rated All Season 17" x 7.5" Full perimeter steel Independent, single coil-over-shock with stabilizer bar Multi-link with coil spring Power rack and pinion 17.75:1

BATTERY Type BCI group size Volts Amp hour rating Cold cranking-amps @ 0°F (-18°C ) Reserve capacity @ 80°F (27°C)

Maintenance free LN3 12 80 660 135 minutes

Vehicle Weight (lbs./kg.)

NORMAL IDLE SPEED: 600-650 RPMS COMPUTER CONTROLLED IDLE SPEED RANGE (PARK): 800-1000 RPM

3. Cargo and load capacity limited by weight and distribution. 4. EPA-estimated MPG. 5. Gross Vehicle Weight Rating (GVWR). When properly equipped, includes vehicle, passengers, cargo and equipment. 6. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo.

GVWR5 4-wheel drive Curb weight10 Payload6 with 40/20/40 split-bench seat GCWR (gross combination weight ratings) Maximum trailer weight7 NOTE: See owner’s manual supplement for loading information

7300/3311 5627/2552 1673/759 14000/6350 8200/3720

7. Maximum trailer weight ratings are calculated assuming a base vehicle, except for any option(s) necessary to achieve the rating, plus driver. The weight of other optional equipment, passengers and cargo will reduce the maximum trailer weight your vehicle can tow. 10. Curb weight in operational status with 100% fuel, fluids and standard base equipment (excludes optional content) * Published dimensions indicated are at curb weight

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe Special Service 5W4 – Vehicle load limits | 21 This information is intended for those who intend to install additional equipment to the police vehicle after it has left the factory, and for those who will be driving and loading the vehicle with passengers and/or cargo. Two labels on your vehicle show how much weight it was designed to carry, the Tire and Loading Information label and the Certification/Tire label. These labels are attached to your vehicle and give you the maximum load capacity, the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for your vehicle. See "Vehicle Load Limits" in the owner manual Index for additional loading information. The following guidelines can help you with proper loading and load distribution when installing additional equipment on the TahoePolice Package. WARNING Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). This can cause systems to break and change the way the vehicle handles. This could cause loss of control and a crash. Overloading can also shorten the life of the vehicle. Adding Equipment to Your Vehicle Before adding accessories or equipment to your police vehicle, there are some things you need to know • The police vehicle's maximum capacity weight (payload). The weight of your police vehicle, including a full tank of fuel but without a driver and passengers. • The weight of items you plan on adding to your police vehicle, like roof mounted light bar(s), push bumpers, security barrier(s), rear storage organizer, highway flares, fire extinguishers, weapons, ammunition, radios, and video equipment. • The weight and number of passengers you intend to carry in your vehicle. • The total weight of any additional cargo you intend to carry in your vehicle. When planning your vehicle equipment installation remember not to exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) of the front or rear axles. To keep the available load weight less than the vehicle capacity weight, you may need to limit the number of passengers you carry in your vehicle or change your choice of additional equipment. Center of Gravity (CG) A vehicle's center of gravity is an imaginary location inside the vehicle and is a balance point for the vehicle mass as it moves down the road. The police vehicle's center of gravity, before you add a load and passengers, is approximately midway between the center of the axles, up from the ground to just below the front window, and between the driver and passenger. Equipment location and weight on the vehicle's center of gravity is important to keep in mind when planning an installation. Heavy equipment should be positioned as low and as far forward in the rear load compartment as possible. Try to mount the equipment below the bottom of the side windows. Refer to the Loading Zone chart and diagram to help with your installation plan. A procedure to make the necessary measurements and formulas to calculate the vehicle longitudinal, lateral and vertical position of the center of gravity can be found in the GM Coachbuilders Manual. Equipment required to conduct the measurements for calculating the center of gravity are: • Weight scales of sufficient capacity to measure the vehicle weight at each wheel. • A post type hoist or other means to safely elevate the front of the vehicle to at least an angle of 20 degrees above horizontal. See your GM dealer to get more information about this coachbuilder procedure. Keeping the center of gravity midway between the axles is also important to provide proper braking performance. About half the total vehicle weight on each axle is recommended. Weigh your vehicle after the additional equipment has been installed to determine the actual weight of your vehicle. Weigh the vehicle with a full tank of fuel and without passengers. You may need to put a limit on how many people or other equipment you can carry inside your vehicle after the additional equipment has been installed.

Note: See loading zone weight chart and diagram on page 22

2014 Chevrolet Municipal Vehicles Technical Manual

22 | Tahoe

4wd Special Service 5W4 – Loading Zones

Loading zone for customer installed equipment and cargo without passengers

Loading Zone Weight Chart – Tahoe Special Service Package (5W4)

38 lbs (17 kg)

52 lbs (24 kg)

90 lbs (41 kg)

137 lbs (62 kg)

546 lbs (248 kg)

683 lbs (310 kg)

175 lbs (80 kg)

598 lbs (271 kg)

773 lbs (351 kg)

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe PPV & 5W4 special equipment - STANDARD | 23 AUxiliary Battery Power Junction Block and Ground Studs

An auxiliary power junction block is located within the driver’s side rear cargo area jack stowage compartment. This junction block is split to provide two circuits for connection to customer-furnished equipment directly to the battery through separate 50-amp circuit breakers. These circuit breakers are located in the breaker/relay panel forward of the instrument panel glove box. A maximum load of 100-amps (1,200-watts) can be connected. This junction block is connected to a coiled 5-foot (1.5 m) branch of rear body harness and fastened near the jack. Mounting of the junction block can be at customer-selected rear cargo area locations permitted by the branch harness length and using customer-furnished mounting hardware. The junction block should not be attached to the interior trim plastic components without appropriate backing hardware to the mounting bolts. Grounding studs are located on the left and right sides of the liftgate opening.

Radio Suppression Ground Straps 4

1

3

5

2

Police Package is equipped with additional grounding in the following locations: 1. Left hand front frame body mount bracket to underbody 2. Left hand rear frame body mount bracket to rear underbody 3. Right hand rear frame body mount bracket to rear underbody 4. Right hand center frame body mount bracket to center underbody 5. Exhaust pipe hanger rod to rear frame hanger

Tire Pressure Monitor

Your vehicle is equipped with a Tire Pressure Monitor (tpm) System which warns of low tire pressure. The tpm System on your Tahoe Police Package has a spare tire sensor but is not programmed to read the spare tire pressure. When the spare tire from your vehicle or an unused spare tire from another Police Package is placed in use as a road wheel, the system will not read the presence of the new tpm sensor and must be calibrated. Refer to your owner’s manual for additional information on the Tire Pressure Monitor and Sensor Programming. The Special Service Package 5W4 does not have sensor in spare tire.

Wiring Provisions for 12-volt battery power supply

Your vehicle is equipped with wiring provisions for a 12-volt battery power supply. Refer to the following information when adding electrical system. The wiring harness is located below the instrument panel near the center of the vehicle. The following information describes the breaker and relay location. The 12-volt battery power is supplied through two underhood mega fuses, one 125-amp and one 60-amp. This underhood power is fed to the breaker/relay center via a harness that passes through the driver side front of the dash, and routed across the instrument pane to a position forward of the glove box. The breaker/ relay center is mounted to the instrument panel structure forward of the glove box. The center includes a plastic bracket, two relays, two 30-amp breakers and three 50-amp mega circuit breakers. Two 30-amp breakers supply power from the underhood 60-amp mega fuse through the contacts of the control relays to a 12-gauge (3.0 mm2) blunt cut wires. These two blunt cut leads are part of wire coiled under the instrument panel near the center of the vehicle. Each relay is operated by a 0.5 mm2 blunt cut, light or dark blue control lead includes in a 3-foot (91 cm) loop of wire under the instrument panel. Three 50-amp mega circuit breakers, protected by three fusible links, supply power directly from the underhood 125-amp mega fuse through three, 10-gauge (5.0 mm2) wires. Two of the wires are routed through the body harness to a split buss junction block to the left rear of the cargo area and secured near the jack and tools. This 3-foot (91 cm) of coiled wires can be accessed by removing the cup holder on the top of the trim panel. The third 10-gauge (5.0 mm2) wire is a blunt cut lead, which is part of the 3-foot (91 cm) loop of wire coiled under the instrument panel near the center of the vehicle. An 8-gauge (8 mm2) ground lead is also provided and it is located under the front passenger sill plate. It can be accessed by removing the sill plate and pulling the loop of wire at the front of the plate, the lead is 3-feet (91 cm) long. Blunt cut ignition control power and signal circuits are also included in the wire coiled under the instrument panel near the center of the vehicle. They include: • A yellow, 20-gauge (0.5 mm2) circuit, hot in ACCESSORY, RUN or RAP (Retained Accessory Power)* • Pink, 20-gauge (0.5 mm2) circuit, hot in Start/Run (7-amp maximum load) • A yellow/black, 20-gauge (0.5 mm2) transmission park signal. This circuit provides switched power when the transmission is in P (Park) and the engine is running. The circuit is at 0-volts when the transmission is in any other position, i.e., R (Reverse), N (Neutral), D (Drive) or M (Manual 6-1). NOTE that the circuit is also at 12-volts with the transmission in P (Park) and the ignition is OFF. To avoid the possibility of undesired parasitic electrical load with the ignition is OFF it is suggested that the Park/Signal circuit be isolated by routing it through the normally open contacts of a customer furnished ignition controlled relay.* • A dark green/white, 20-gauge (0.5 mm2) Vehicle Speed Signal (VSS) provides 4,000 pulses per mile. The breaker and relay center is located behind and above the instrument panel storage compartment. Remove contents from the storage tray. Using the tab at the back of the compartment drop the tray down gently toward the floor. You will find the breaker/relay center above the right rear corner of the storage compartment. * These two circuits share a 15-amp fuse. (10-amp combined maximum load) NOTE: For wiring diagram see pages 28 through 31

2014 Chevrolet Municipal Vehicles Technical Manual

24 | Tahoe

PPV & 5W4 special equipment - STANDARD

Interior/Exterior LampS Control

(PPV ONLY)

Engine Oil Cooler

(5W4 ONLY)

9G8 - Delete Daytime Running Lamps and Automatic Headlamps. This option disables the Daytime Running Lamps and Automatic Headlamps control feature. Exterior lamps are manually controlled only. Option 9G8 not available in Canada. Courtesy lamps, including dome lamps, can be turned off with a push button switch which is above the interior lamp intensity control knob. When the switch is activated, courtesy lamps remain off when any vehicle door is open. If a door is open when the switch is activated, the lamps will go off. The instrument cluster and radio lighting dimmer control will override the push button switch to turn on the courtesy lamps. The headlamp control on the driver’s side of the instrument panel operates the headlamps. If your Tahoe does not have option 9G8, Delete Daytime Running Lamps and Automatic Headlamps, the Daytime Running Lamps and Automatic Headlamps can be turned off for one ignition cycle by rotating the control knob momentarily counter-clockwise. See also section 3 of your Tahoe owner’s manual. In Canada, the Daytime Running Lamps and Automatic Headlamps can be turned off if the transmission is in Park. See also your Tahoe owner’s manual.

Engine oil cooler located in the left hand radiator tank. Cooler consists of an inlet and an outlet pipe attached to the engine oil filter adapter which transmits the oil to the cooler and then back to the engine. The cooler itself consists of numerous flat plates through which the hot oil flows, transmitting heat to the coolant and cooling the oil.

Transmission Oil cooler

Service parts identification label

E L MP

SERVICE PARTS IDENTIFICATION

DO NOT REMOVE

1GNLC2E0BR8152140 AGK BDR IPG OST UW6 3FL 7X6 BC/CC

AG2 B3B JA9 QPP UIC 6A3 8MZ

AL0 AMF B42 B86 JL9 KD1 R7V R9N U77 VT7 6E2 6HP PPV 9MZ U 636R

SA

AP3 B9V KG4 R9Z V8D 6J1

AR9 C67 LGD SLM WL9 6J3

AT8 DK2 MX0 T53 ZFH 6J4

PDBJCH AXJ AY0 EF7 E2C M15 NK5 UH8 UJM 1SZ 19C 6J7 7B3

A75 FE9 NT7 UN9 41U 7HP

CC10706 A76 FR9 N99 UT7 191 7M9

External air-to-oil cooler is mounted in front of coolant radiator and A/C condenser at the center and is connected in series with the integral transmission oil cooler in the right end tank of the coolant radiator.

Power steering cooler

A Service Parts Identification (SPID) Label provides Vehicle Identification Number (VIN)-specific Option Code content list, Engineering Model Number (Nameplate, body style), Exterior paint system, Exterior paint color code and Interior trim level and color. The SPID label for the Tahoe is located on the inner surface of the instrument panel storage compartment (glove box).

Stabilitrak control

Vertical finned cooler is mounted in front of the radiator at the left side of the radiator and connected in-line between the power steering pump and steering gear.

Covering - Floor OFF

The Stabilitrak stability control system control button is located below the air conditioning fan control See pages 3 or 15 of this manual for an operation description of the stability control system or see your Owner's Manual.

Black heavy-duty one piece. Replaces production carpeting.

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe PPV & 5W4 special equipment - OPTIONAL | 25 AMF - Package of 6 transmitters With Remote Start and Liftglass (Without Remote Similar)

6B2 – Rear Door Handles Inoperative

With Remote Start and Power Liftgate and Liftglass (Without Remote Start Similar)

Relearn Remote Key To access this DIC display, the vehicle must be in PARK. This display allows you to match the remote keyless entry transmitter to your vehicle. To match a remote keyless entry transmitter to your vehicle, do the following: 1. Press the trip odometer reset stem until PRESS THE RELEARN REMOTE KEY displays. 2. Press and hold the trip reset stem for 3 seeconds. The message REMOTE KEY LEARNING ACTIVE will display. 3. Press and hold the LOCK and UNLOCK buttons on the first transmitter at the same time for approximately 15 seconds. A beep will sound indicating that the transmitter is matched. 4. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it. 5. To exit the program mode, turn the key to the LOCK position. NOTE: A maximum of 8 keys may be learned for a vehicle immobilizer (Passkey III+) with a random key code. Vehicles with the fleet key option (RPO 6E2 or 6E8) may have an unlimited number of keys learned for the particular option fleet key and must be learned using one of the original "master" keys. When programming the RPO AMF additional 6 remote transmitters, the original 2 transmitters delivered with a vehicle must also be reprogrammed at the same time. A maximum of 8 remote transmitters can be programmed for a single vehicle.

Inside rear door handles are disconnected. Rear doors can only be opened from the outside.

6N5 SWITCHES – REar Window Inoperative

Rear door window switches are inoperable. Rear door power regulators are operable only from driver position switches.

6N6 – Rear Door Locks Inoperative

TRW – Wiring provisions for emergency vehicle roof lamp Rear door locking rods are disabled. Rear door locks are inoperable at rear doors, but operate from driver position.

Battery power is supplied through a 30-amp fuse to a wiring harness located in the roof. Power is controlled with a switch located in the overhead console. The customer or vehicle upfitter must complete the installation to an added accessory such as an emergency beacon lamp. Maximum rated electrical load is 21-amp (250-watts). The added electrical requirements must not exceed 21-amp (250-watts). Running the accessory for long periods of time with the engine off may run the battery down. A. 25.39-inches (645 mm) B. 17.32-inches (440 mm) C. 3.94-inches (100 mm) square D. Roof centerline E. Roof edge NOTE: For wiring diagram see page 26

2014 Chevrolet Municipal Vehicles Technical Manual

26 | Tahoe

PPV & 5W4 special equipment - OPTIONAL

Autonet Mobile wifi; in-car router

Delivers high speed network connectivity to vehicles by leveraging the 3G network. Autonet Mobile's TRU Technology, a proprietary and patented technology, provides a seamless connection regardless how fast you are traveling. Unlike conventional cellular data technology, TRU Technology manages data as users travel at high speeds between cell towers, eliminating dropped connections. CarFi™ provides wireless device connectivity within the vehicle using standards-based 802.11 Wi-Fi networking. This allows users in and around the vehicle to access the Internet using any Wi-Fi enabled device. Available through your GM dealer.

WX7 – WIRING PROVISION FOR FRONT SPEAKERS

Approximately 60 inches (1.5 m) of auxiliary speaker wiring is routed from the front door and windshield pillar speakers and coiled under the instrument panel. The wiring permits connection of the front speaker pairs to customer-installed communication equipment. Vehicle radio front speaker outputs are re-routed to the rear speakers to maintain the required open door/key-in-ignition audible warning. NOTE: For wiring diagram see page 27

6J4 – WIRING PROVISION FOR horn siren circuit

7X6 and 7X7 – SpotLamps

This provision permits customer connection of a switch to select either horn of siren operation when the horn pad is pressed.

7X6 Spotlamp left hand, pillar-mounted unity, 6-inch with replaceable H3 halogen bulb; independently fused

A 22-gauge (0.35 mm2) wire is connected to an in-line connector in the horn circuit of the instrument panel harness under the instrument panel. The end of this harness extension is a 5-foot (1.5 m) loop of wire coiled under the center of the instrument panel. NOTE: For wiring diagram see page 26

7X7 Spotlamps left and right hand, pillar-mounted unity, 6-inch with replaceable H3 halogen bulb; independently fused NOTE: • Lamp bulbs are halogen 12 volt 100 watt H-3 rated at 245,000 candle power • For wiring diagrams and fuse location see page 27 • Customer furnished spotlamp assembly must be installed to avoid interference with deploying passenger airbag

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe PPV & 5W4 special equipment - OPTIONAL | 27 6j7 – Exterior lamps Emergency Flashing System module location

6j7 – Exterior lamps Emergency Flashing System

Option 6J7 provides a headlamps high beam flashing module, rear lamps flashing via the Body Control Module (BCM) and a control wire for customer-furnished switching to turn the module on and off. The flasher control wire is part of the blunt-cut upfitter harness coiled under the instrument panel in the front passenger side foot well. The flashing module is located below the passenger side headlamp and forward of the passenger side front wheel on the inner front fender sheet metal.

The Option 6J7 Exterior Lamp Emergency Flashing System flashing module is mounted on a front sheet metal vertical surface, forward of the passenger side front wheel inner wheelhouse and below the passenger side headlamp.

6j3 – Wiring Provisions for Vehicle Grille Lamps and Speaker/Siren B

The headlamp flashing module is activated by the application of 12 volts to a dark green/red wire in the upfitter harness. When activated, the headlamp high beams and the high beam instrument cluster indicator will flash alternately at 2.4 flashes per second. When the flashing module is turned on, the module sends a signal to the BCM which alternately flashes the stop lamps and backup lamps at the same flash rate as the headlamps. Depressing the brake pedal will override the stop lamp flashing and placing the transmission in Reverse will override the backup lamps flashing. During daylight conditions, the Daytime Running Lamps (DRL) are automatically turned off whenever the headlamps flashing module is activated. During night time conditions, the low beam headlamps automatically turn on while the high beam lamps flash. Turning on the high beam headlamps manually will override the flashing module and the high beam headlamps will operate continuously. During night time conditions the tail lamps will turn on automatically. If Option 9G8 is present the low beam headlamps and tail lamps will not come on automatically. The Center Mounted Stop Lamp will operate only when the service brakes are applied.

A A. B lunt cut ends for the customer-furnished grille lamps and customer-furnished siren/speaker B. Control wires from in-line connector in forward lamp harness for customerfurnished grille lamps and speaker The SEO 6J3 wiring provision has a 5-foot (1.5 m) harness coiled underneath the instrument panel on the passenger side. The wiring circuits are routed from under the instrument panel to a 1-foot (30 cm) coil secured in the area behind the grille. There are four 16-gauge (1.0 mm2) wires for connecting to the grille lamps (GRY, TAN) and siren speaker (LT BU, LT GN) The SEO 6J3 wiring provision also includes one 18-gauge (0.8 mm2) control wire for the SEO 6J7 Exterior Lamps Emergency Flashing System.

A 20-amp fuse labeled HEADLAMP WASH protects the flasher module circuit. The fuse is located in the under hood fuse block in the engine compartment on the driver side of the vehicle. See also the Owner Manual for more information. Activation of the headlamps flashing and rear lamps flashing can be separated by opening the dark-blue/yellow BCM circuit at the flasher module connector, C122-F, and applying a customer-switched ground to the harness side of the wire at the connector. Power to dark green/red wire must be off to flash rear only.

Warning: BCM will be damaged if 12V power is connected to the dark-blue/ yellow wire.  NOTE: For wiring diagram see page 24

When option 6J7 is installed without option 6J3, only the dark green/red control wire is proved for connection to custo mer-furnished 12-volt switching to turn the Emergency Flashing System on or off. NOTE: For wiring diagram see page 24

2014 Chevrolet Municipal Vehicles Technical Manual

28 | Tahoe

PPV & 5W4 – Wiring Diagrams Wiring Diagram for 12-volt battery power supply

Wiring Diagram for Controlled power and signal circuits with 12-volt power supply

*

* Zero volts out of Park, engine running; hot in Park with ignition Off.

NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe PPV & 5W4 – Wiring Diagrams | 29 Wiring diagram for option 6j3 and option 6j7

122

Wiring Diagram for forward lamp harness in-line connector for use with headlamps flasher module, option 6j7

Warning: BCM will be damaged if 12V power is connected to the dark-blue/yellow wire. 

NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

30 |

Tahoe PPV & 5W4 – Wiring Diagrams Wiring diagram for option 6j4 in-line connector

Wiring diagram for OPTION TRW emergency roof lamp

NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe PPV & 5W4 – Wiring Diagrams | 31 Wiring diagram for OPTION WX7 in-line connector

WX7 inline harness added here to send LF and RF outputs to LR and RR speakers. Blunt cut circuits from front speakers are coiled in front under the instrument panel.

Wiring Diagram for WINDSHIELD PILLAR-MOUNTED SPOTLAMP - OPTION 7X6 and 7X7

EXP/PTO Minifuse 15A

UNDERHOOD FUSE CENTER SEOB1 Minifuse 15A

-Spotlamp LH 2640 0.5

RD/WH

J5

P5

B4

RD/WH

2640 0.5

RD/WH

4540 0.5

H7635

A PWR

CASE GND

-Spotlamp RH 4540 0.5

RD/WH

J2 D3

P2

H7635

A PWR

CASE GND

7x6 spotlamp left hand and 7X7, spotlamps left and right hand, pillar-mounted Unity, 6-inch with replaceable h3 halogen bulb; independently fused

NOTE: Wiring diagrams for these options are shown in the Police Package owner’s manual supplement (shipped in glove box).

2014 Chevrolet Municipal Vehicles Technical Manual

32 |

AIR BAGS FAQ

Can specialty vehicle equipment (e.g. radar devices, video cameras, computers, meters, radio trees, shotguns, etc.) still be mounted in cars with passenger side air bags? Yes, but care must be taken to mount the equipment outside of the deployment zone. Air bags inflate with great force and will interact with any object in the deployment zone. Therefore, to reduce the risk of injury to vehicle occupants, GM recommends that the air deployment zone be kept free of any equipment. If a piece of equipment were to become dislodged it could strike an occupant in the vehicle and result in injury. The likelihood of an object becoming dislodged is influenced by many factors, including the proximity of the object to the inflatable restraint, the size and shape of the object, and the means by which the object is secured to the vehicle. In addition to these factors, the trajectory and velocity of a dislodged object can be influenced by the type and severity of vehicle crash. Objects that are in the deployment zone, but do not become dislodged by an inflating air bag can still affect the performance of the air bag. For example, such objects could tear the fabric or affect the shape of the air bag, thus reducing the ability of the bag to provide restraint. Is it possible to shield equipment that is installed in the passenger side frontal air bag deployment zone in a manner that will allow full and safe air bag deployment? Due to the complexity of influencing variables, GM is unable to evaluate the potential for shielding expected equipment configurations in all accident scenarios in order to assure that the air bag performance would be unaffected. While shielding may protect certain equipment from being damaged or dislodged, it may also negatively affect the inflation characteristics of the air bag. The air bag’s shape, inflation angle, fold pattern, and inflation rate and pressure are developed to maximize the protection capability of the inflatable restraint system. Therefore, GM cannot recommend the placement of any equipment in the deployment zone, even if it is shielded to protect it from damage. Front air bag systems and instrument panel mounted equipment. Passenger air bags in GM vehicles deploy in different ways depending upon the type of vehicle and the particular instrument panel design. In some vehicles, the passenger air bag deploys through a discrete door located on the top surface of the instrument panel (top-mount air bag systems). In other vehicles, such as the Chevrolet Tahoe, the passenger air bag deploys through a discrete door mounted on the vertical rearward surface of the instrument panel, above the glove box door (mid-mount air bag system). With these types of topmount and mid-mount passenger air bag systems, the top pad of the instrument panel remains in place during deployment. Some GM passenger air bag systems, like the system in the Chevrolet Impala, deploy from beneath the instrument panel top pad. These are considered 3/4-mount air bag systems with a “deployable top pad.” The entire instrument panel top pad is the “deployment door” from under which the inflating air bag emerges. When an air bag deployment is commanded, the forces from the inflating passenger air bag push up on the instrument panel top pad, releasing special fasteners across the rearward edge of the top pad. This allows the top pad to rotate upward so that the passenger air bag may emerge. The top pad rotates upward to open widest at the right hand side, and is usually forced upward into contact with the windshield on the right hand side of the vehicle during a deployment.

Instrument panel top mounted special equipment, such as a radar antenna and control unit or video camera must be positioned to the left of the vehicle center line. This equipment must be mounted as low as possible and securely fastened to the top pad to avoid being dislodged in the event of a crash and possible air bag deployment. In the process of securely fastening special equipment to the top, DO NOT fasten down the top pad itself to any other vehicle component such as the cluster trim plate. As described above, the top pad rotates upward during a deployment. In order to enable the proper deployment of the passenger air bag, specialty equipment installation MUST NOT PREVENT the top pad from rotating upward during deployment. Location and attachment of special equipment should minimize added resistance or interference to upward rotation of the top pad during deployment. Side-Impact Air Bags for crashes to the vehicle sides. The air bag system in your police vehicle includes includes roof rail mounted Head Curtain side air bags.. The vehicle is also equipped with seat back mounted upper body air bags located on the outboard side of the driver and front passenger seat backs. Together the Head Curtain and seat-mounted side air bags are intended to protect the head and upper body in the event of a side crash. Some vehicles may also be equipped with an optional air bag, mounted on the inboard side of the driver seat back. Can Specialty Vehicle Security Barriers be mounted within the side air bag deployment zones? No. The side air bags inflate extremely fast because of the nature of side crashes to the vehicle. Mounting a security barrier behind the front seats with the ends placed within the side air bag deployment zones will result in unintended interaction between the barrier and the inflating side air bags. To reduce the risk of injury to the vehicle occupants, GM recommends that the side air bag zones be kept free of any customer installed equipment. Customer furnished equipment installed to the vehicle roof. Your police vehicle is designed with an interior roof cover system which includes internal components for the interior lamps and wiring. The roof system may also include side air bag components. Inflation devices may be mounted on the vehicle roof side behind the rear doors as well as air bag tethers retained to the windshield pillars. Care must be taken to avoid damage to these components or interference with their operation when installing roof mounted equipment such as emergency lamps and communication antennas. Recommended GM service procedures must be followed to remove and re-install the instrument panel top pad to ensure that the top pad will release properly in the event of a passenger air bag deployment. On the right half of the top pad closest to the passenger air bag module, GM recommends that no equipment be mounted. When mounting equipment on the driver side of the top pad, GM recommends that the total mass of the top pad mounted special equipment not exceed 8 pounds (3.6 kilograms), since some top pads tend to rotate about the left end. Fasteners used to secure special equipment to the instrument panel top pad, the windshield glass, or to the windshield upper frame (header), should be selected to ensure that these devices will remain attached during a vehicle crash and possible air bag deployment.

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

AIR BAGS FAQ

| 33

Can the installation of push bumpers on the front end of the vehicle affect the deployment of the air bag?

I've heard that a deployed air bag produces whet appears to be smoke, is the air bag hot?

General Motors is not aware of adverse effects during crash events from the many push bumpers thai have been installed on GM police vehicles. Because there are many styles of push bumpers available with varying crash characteristics, installation of push bumpers may or may not affect deployment timing of the air bags. Push bumpers should be mounted to avoid modifying the vehicle structure and interfering with the front air bag sensors mounted on the upper radiator support cross member

After the bag has deployed in a crash, the air bag itself will not be hot to touch. Some components within the air bag module will be hot for a short time. A small amount of smoke coming from a deployed air bag module is normal and should not be cause for concern.

Two front impact sensors are installed in General Motors vehicles. Do not relocate or disconnect the front sensors. The location and orientation of the front sensors are critical for correct operation of the air bag system. Avoid mounting components on or near the sensors. Push bumper styles with vertical pushing members that are in foreaft alignment with the front air bag sensors are not recommended. When should an air bag inflate? The driver's and right-front passenger's frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system's designed "threshold level." In addition, your vehicle has “dual stage” frontal air bags which tailor the the amount of restraint according to crash severity. For moderate frontal impacts, the air bags inflate at a level less than full deployment. For more severe frontal impacts, "dual stage" frontal air bags deploy at full levels. If the front of your vehicle goes straight into a wall that doesn't move or deform, the threshold level of the reduced deployment is about 12 to 16mph (19 to 15 km/h), and the threshold level for a full deployment is about 18 to 24 mph (29 to 28.5 km/h). The threshold level can vary, however, with specific vehicle design, so that it can be somewhat above or below this range. If your vehicle strikes something that will move or deform such as a parked car, the threshold level will be higher. The driver's and right-front passenger's frontal air bags are not designed to inflate in rollover, side impacts, or rear impacts, because inflation would not help the occupant. Seat mounted side impact air bags are designed to inflate in moderate to severe side crashes. The side impact air bags will inflate if the crash severity is above the designed "threshold level." The threshold level can vary with specific vehicles design. The side impact air bags are not designed to inflate on frontal or near-frontal impacts or rear impacts, because inflation would not help the occupant.

Also, when the nitrogen gas is vented out of the air bag, small particles from inside the bag are also vented into passenger compartment. These airborne particles look like smoke and some particles are deposited as residue on and around the air bag. I've heard that the dusts that are released into the passenger compartment from the air bag are harmful, is this true? For most people, the only effect the dusts will produce is some irritation of the throat and eyes, and that is only if the occupant remains in the vehicle for many minutes after the air bag deployment with no ventilation and windows closed. However, some people with asthma may develop an asthmatic attack from inhaling the dusts. If this happens, they should first treat themselves the same way their doctor has advised them to treat any other asthma attack, and then immediately seek medical treatment. Can the air bag system be re-used? No, The air bags are designed to inflate only once. After inflation some new parts will be required. These will include the air bag module and possibly other parts. (A competent service technician with access to the vehicle's service manual and the required tools should replace the required components after a deployment crash.) If my vehicle has air bags, why should I have to wear my safety belt? Air bags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts not instead of them. Every air bag system ever offered for sale has required the use of safety belts. Even if you're in a vehicle that has air bags, you still have to buckle up to get the most protection. That's true not only in frontal collisions but especially in side and other collisions.

Roof rail mounted head-curtain air bags are designed to inflate in moderate to severe side crashes. In addition, certain vehicles have head-curtain air bags which are also designed to inflate in situations where an impending rollover condition is identified by the vehicle's rollover sensing system and/or frontal or near-frontal impacts if the crash severity is above the designed "threshold level". Safety belt pretensioners at the driver and front passenger seat positions are designed to deploy in frontal, near-frontal, side, and rear crashes that exceed the "threshold level" of crash severity to help reduce slack in the safety belt Safety belt pretensioners will also deploy in impending rollover situations. How long will the air bag remain inflated? It takes approximately 1/20th of a second to fully inflate the frontal air bags. This is faster than the blink of an eye. The air bags begin to deflate immediately, helping to stop the occupants more gradually.

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

34 | Tahoe

PPV & 5W4 – AIR BAG DimensionS

Top View of Instrument Panel and APproximate Deployment Area of the Air bag Zone A. B. C. D. E. F. G. H. I. J. K. L. M.

Passenger side instrument panel top surface zone Passenger side air bag module trim panel – rear edge Passenger side door Approximate dimensions of inflated air bag Passenger side air bag deployment zone Passenger centerline Inside rearview mirror Vehicle centerline Driver centerline Driver side air bag deployment zone Front of steering wheel Driver side door Shift selector arc

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

Tahoe PPV & 5W4 – AIR BAG DimensionS | 35

Side View of Driver Side Air bag Deployment Zone

A. Top edge of windshield B. Top of instrument panel C. Inflated air bag – steering wheel D. Centerline of steering column at mid-tilt E. Driver air bag deployment zone F. Front of steering wheel

Side View of Passenger Side Air bag Deployment Zone

A. Top edge of windshield B. Inside rearview mirror C. Instrument panel top surface zone D. Passenger side air bag module trim panel – rear edge E. Inflated air bag – horizontal dimension approximate 15.4 in (390 mm) F. Inflated air bag – vertical dimension approximate 9.3 in (490 mm) G. Inflated air bag – instrument panel H. Passenger air bag deployment zone

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

36 | Tahoe

PPV & 5W4 – AIR BAG DimensionS

Head Curtain and front Seat-Mounted Side IMpact Air bag Deployment Zones Passenger Side Shown, Driver Side Similar L

J

500 mm 20 in.

N H

30 mm 1.2 in.

C

A

K

I

B

O

G

75 mm 3.0 in.

F E

D M

P

­ Tahoe Rows 1 and 2 A.  Top of deployment zone – along head curtain at edge of headliner B.  Back of deployment zone – at rear top corner of rear door pad C.  Rear quarter window D. Bottom outside edge of rear quarter window E. Bottom of air bag deployment zone – parallel to outside bottom edge of rear quarter glass F.  Top edge of rear door pad G.  Top edge of front door pad H.  Dimension at mirror patch from top edge of front door pad

I.  Front of deployment zone at front upper corner of front door pad J.  Windshield pillar trim with grab handle K.  Visor L.  Deployment zone - Tahoe seat rows 1 and 2 M. Rear of Tahoe  Tahoe Seat Air bag N. Center of door trim pull handle O. Top of surface of outboard front seat cushion P. Back edge of center pillar trim­

Head curtain and front Seat-Mounted Side IMpact Air bag Deployment Zones View from Rear Cargo Area

A.  Head curtain air bag deployment zone B.  Underside of headliner C.  Edge of headliner D.  Inner center pillar trim E.  Inner door pad

F.  Seat centerline G. Bottom of door windows H. Front seat headrests I. Seat-mounted side impact air bags deployment zone front seat J. Top surface of outboard front seat cushion

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

Anti-lock braking system FAQ | 37 GM offers Anti-Lock Brake Systems as standard or optional on all North American passenger vehicles and light truck lines. The computerized Anti-Lock Braking System (ABS) is designed to keep the vehicle’s wheels rotating as the brakes are applied to assist the driver in achieving a controlled stop. Sensors monitor how fast the wheels rotate and feed the data continuously to the ABS computer. The vehicle’s brakes slow each wheel as the brake pedal is applied. However, when ABS is activated due to road conditions, the system repeatedly releases and applies pressure to the brakes. The wheels can keep rolling, thus retaining steering ability and enhanced stability while providing a higher braking force on most surfaces than a locked wheel provides. How exactly does ABS work? In cars without ABS, hitting the brakes can cause the wheels to lock, leaving you unable to steer the vehicle until you decrease the pressure so the wheels can roll again. With an ABS, as you apply the brakes, the ABS computer monitors the wheel speed sensor information. If the computer senses that a wheel is approaching lock up, it sends a signal to the hydraulic modulator to reduce, then to reapply, brake pressure several times a second for as long as you maintain firm pressure on the brake pedal. The process is much like the threshold braking technique used with conventional brakes. However, ABS does it much faster and more accurately than any driver can, leaving you free to focus on steering away from obstacles.

Does ABS reduce stopping distances?

Should I drive an ABS equipped vehicle differently than I would drive a vehicle with conventional brakes? Most of the time, under normal driving circumstances, there is no difference, and you should always drive with the same caution and care. It is important to realize that ABS only makes a difference when it is activated—when you have to brake hard—and that would only be when the computer senses that a wheel is approaching lockup. When ABS activates, keep steady pressure on the brake pedal and then let the ABS work for you. Don’t pump the brakes or try to ­find the threshold. Simply hold the brake pedal down and steer if necessary to avoid an obstacle.

Is ABS always active? ABS is always available, but not always activated. ABS is activated only when the brake pedal is applied and the computer detects an impending wheel lock condition.

Can older cars be retrofitted with ABS? No! The brake system is one of the most important features on any passenger vehicle. Several products, which tap into the master cylinder and/or brake system performance, are being sold in the aftermarket. Some of these products imply performance similar to new vehicle anti-lock brake systems. However, contrary to their claims, add-on systems, which deplete fluid from the master cylinder on brake apply may actually increase a vehicle’s stopping distance. This may cause the vehicle to fail to comply with Federal brake standards.

Does ABS always activate at the same speed? No, the system operates when the computer detects wheel lockup, at any speed above 8 mph.

Yes, in braking situations where the wheels on a non-ABS equipped vehicle would lock up, ABS will generally provide shorter controlled stopping distance. The amount of improvement in stopping distance depends on many factors, including the road surface, severity of braking, initial vehicle speed, etc. On some surfaces, such as gravel roads, braking distances can be longer, but you will still have the control benefits of ABS. The important capability of ABS is control. ABS provides improved vehicle steerability and stability when braking.

Will ABS wear out a vehicle’s brakes sooner?

What can affect the ABS advantage?

Do Federal Safety Standards mandate ABS?

It is important that you follow the maintenance schedule recommended in the owner’s manual of the vehicle, tires should be at their proper inflation level, the brake pads should be checked regularly, etc. While driving, you should sit comfortably, so that your hips are back in the seat and your knees are bent, even while braking. Your foot should be positioned so that your heel is on the floor and your toes are secure on the lower half of the pedal. And, though ABS may reduce stopping distance, remember: The faster you go, the longer it takes you to stop. Keeping a safe distance between you and the vehicle in front of you is always necessary, even with ABS.

A properly maintained brake system will be unaffected by ABS operation under typical driving conditions.

Are there different types of ABS? Yes, there are rear wheel anti-lock systems (RWAL) used on some trucks and four-wheel ABS available on cars and trucks.

No. Federal standards establish minimum braking performance requirements that all vehicles must meet, but do not specify how they should be met. It should be noted that even a vehicle with failed ABS meets the Federal safety standard for stopping distances.

Will a tire size change affect ABS? Use of tires other than original equipment may affect ABS performance. Owners should consult and follow the recommendations contained in the vehicle owner’s manual regarding replacement tire size. NOTE: ABS will work with original equipment spare tire or tire

What happens if ABS becomes inactive?

chains. However, performance is reduced.

The ABS electronic control unit has on-board diagnostic capability. If a fault is detected, the vehicle will revert to the base brake system, and the ABS telltale on the dash will be illuminated. Should this happen, the vehicle should be taken to a dealership for repair as soon as possible.

Do insurance companies give a discount for ABS?

How do I use ABS? Depress and hold the pedal. DO NOT PUMP THE BRAKES (that prevents the system from working). Just hold the brake pedal down and let the ABS work for you. You may feel the brake pedal vibrate, or you may notice some noise, but this is normal as the system works for you.

Yes, many insurance companies give discounts that range from 5% to 10%. In the states of New York and Florida all insurance companies are required to give an ABS discount of 5% on certain coverages such as bodily injury, property damage, collision, and personal injury protection. In other states the discount varies from insurance company to insurance company. When buying auto insurance, always ask your insurance agent if his/her company gives a discount for vehicles equipped with antilock brakes.

2014 Chevrolet Municipal Vehicles Technical Manual

38 | Anti-lock

braking system and Stabilitrak

IMPORTANT DRIVING SAFETY TIPS A. A lways maintain a safe

following distance. ABS does not

allow you to stop on a dime. (Generally a 2-second following distance is considered safe in ideal conditions.) Watch the vehicle in front of you pass a fixed marker (such as a sign). Count seconds—one-thousand-one, one-thousand-two-until your front bumper reaches the marker. If you do not count out two seconds, then you are too close to the vehicle in front of you. Also, if the roads are wet or icy, or visibility is poor, you should increase your following distance.

B. A lways drive carefully—

especially on slippery surfaces. ABS cannot create friction between the tires and the road surface, it can only give the driver the maximum advantage of the existing adhesion. If the vehicle is traveling on a surface with no adhesion, the best ABS in the world cannot provide a shorter stopping distance or good steering.

C. It is a good idea to practice an

ABS activated stop and get the feel of the brake pedal. However, please make sure it’s at a safe time with no obstacles in your path. And you only really need to try it once or twice to know what happens.

Electronic Stability Control systems (StabiliTrak) Q. How does StabiliTrak work? StabiliTrak systems help drivers maintain control of their A. StabiliTrak has the ability to apply control forces to vehicles, especially during emergency lane changes or the vehicle independent of the driver. StabiliTrak uses avoidance maneuvers. StabiliTrak uses various sensors, sensors to continuously compare the path indicated by such as steering wheel angle, wheel speed, yaw velocity, the steering wheel position to the vehicle’s actual path. If etc., to detect any difference between the path requested a discrepancy is detected, StabiliTrak selectively controls by the steering wheel position and vehicle’s actual path. vehicle brakes and engine torque to create a yaw moment When appropriate, the system selectively controls brakes, that helps restore the vehicle’s actual path to the path engine power, and even suspension settings to enhance indicated by the steering wheel position. StabiliTrak has control of the vehicle’s direction and help keep it on course. the ability to help correct both understeer (where the Independent studies conducted by the National Highway vehicle is not turning as much as the steering wheel Traffic Safety Administration, the Insurance Institute for position indicates) and oversteer (where the vehicle is Highway Safety, and others have found StabiliTrak to be turning more than the steering wheel position indicates). highly effective in reducing vehicle crashes. General Motors The illustration at right shows how selective braking at a offers StabiliTrak systems on many of its passenger car particular wheel can create a compensating yaw moment and light truck models. to help restore the vehicle’s actual path to the path See your owner's manual for additional information about indicated by the steering wheel position. the operation of StabiliTrak. Q. Will a tire change affect StabiliTrak? Q. How do I use StabiliTrak? A. Use of tires other than original equipment may affect A. S  tabiliTrak operates independently of the driver. You StabiliTrak performance. StabiliTrak is designed to make should continue to drive your StabiliTrak equipped the best use of available traction. The performance vehicle with caution and care. GM’s StabiliTrak system, characteristics of the original equipment tires are part of StabiliTrak, is designed to be as seamless as possible in the overall system effectiveness. When you replace tires operation, to be part of the overall vehicle response and to check the recommendations in your owner's manual. On make a good vehicle better GM vehicles, the original equipment tires have a “TPC” (Tire Performance Criteria) code on the sidewall. Replacing the tires with the same “TPC” code will help assure proper StabiliTrak performance.

2014 Chevrolet Municipal Vehicles Technical Manual

Express transport Van-1ls/2ls | 1

Updates for 2014 New Features

• Silver Ice Metallic (GAN) • Cyber Gray Metallic (GBV) • Brownstone Metallic (GWX)

Deleted



• • • •

Sandstone Metallic (15U) Graystone Metallic (16U) Sheer Silver Metallic (GGZ) Mirrors, outside heated power-adjustable, black manual-folding with integrated turn signals (DE7)

2014 Chevrolet Municipal Vehicles Technical Manual

2 | EXPRESS

TRANSPORT VAN – 1LS & 2LS

NOTE: This vehicle is NOT designed nor intended for use IN HIGH SPEED EMERGENCY VEHICLE OPERATIONS Cg33406-1LS (gas/diesel) Rear-wheel drive Cg33706-2LS (gas/diesel) Rear-wheel drive

Model availability Standard equipment summary

Warranty

3 years / 36,000 mile bumper-to-bumper (whichever comes first, see dealer for details) 5 years / 100,000 mile limited powertrain (whichever comes first, see dealer for details)

INTERIOR FEATURES Air conditioning Single-zone, manual (front). Rear air and rear heat available on 33706 models Cup holders Three on engine console cover Defoggers Front and side windows DOME Lamps Three dome lamps, with defeat switch and door-activated switches DRIVER INFORMATION CENTER See order guide Floor Covering Full-length Black rubberized-vinyl Mirror Inside rearview manual day/night Power outletS Two auxiliary on engine console with cover 12-volt Radio am/fm stereo, seek-and-scan, digital clock and 2 front door speakers

Restraint System Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, rollover sensor, and dual head curtain air bags1 for front and rear seat outboard occupants Seats, Front Vinyl high-back buckets, adjustable and reclining Seats, rear Vinyl trimmed rear bench seats and split 4 passenger last seat Seating 12 passenger seating Speedometer/cluster Analog with speedometer, odometer with trip odometer, fuel level, volt meter, engine temperature and oil pressure Steering column Tilt Theft deterrent Vehicle theft PASS-Key® III

Exterior features Bumper, Front Painted, Black Bumper, Rear Painted, Black with step pad Doors Swing-out side, 60/40 split on passenger side only Glass Solar-Ray, deep tinted; enhanced technology rear most side glass (All windows except light-tinted on windshield and driver and front passenger side glass, enhanced-technology, rear most side windows. 3-layer special glass is designed to help reduce the risk of ejection during a crash, swing-out rear cargo door windows, swing-out side door windows)

Grille Headlamps LAMPS License plate kit Mirrors Tire pressure monitor WINDSHIELD WIPERS

Black composite Single rectangular halogen Daytime running Front Outside, rearview, manual, foldaway, Black check tire pressure (no spare tire sensor) Intermittent wet-arm with pulse washers

Chassis features Alternator 105-amp without rear A/C, 145-amp with rear A/C, 145-amp standard on 2LS model Battery 600 CCA with run-down protection and retained accessory power on 1LS model. Dual heavy-duty 770 CCA standard on 2LS model Brakes 4-wheel disc, with 4-wheel anti-lock Engine Vortec 4.8L V8, SFI FlexFuel2 or 6.6L V8 turbo diesel Exhaust Aluminized stainless-steel muffler and tailpipe Fuel tank capacity 31 gallon (117.3 liters) Monitor Oil life Oil Cooler External transmission Stabilitrak Vehicle stability control

StEERING Power Suspension, front Independent with coil spring and stabilizer bar Suspension, rear Hypoid drive axle with multi-leaf springs Tires lt245/75r16e all-season, blackwall with full-size spare located under rear underbody Tire pressure monitor  check tire pressure will show on driver message center Transmission 6-speed automatic, heavy-duty, electronically controlled with overdrive and tow/haul mode and internal transmission oil cooler Wheels 16" x 6.5" steel includes Gray center cap and steel spare

1. H  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. 2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

EXPRESS TRANSPORT VAN – 1LS & 2LS | 3 POWERTRAIN

ENGINE TRANSMISSION AXLE

MODEL

CODE

TYPE

DISPLACEMENT

LITERS/CU. IN. 1LS L20 V8 4.8L/293 Standard Vortec 1LS L96 V8 6.0L/366 Optional Vortec 2LS LGH V8 6.6L/403 Standard Duramax

FUEL

STANDARD

TYPE

SYSTEM SFI Automatic Automatic FlexFuel2 MXO/MYD HD 6-speed SFI Automatic Automatic FlexFuel2 MXO/MYD HD 6-speed Turbo Automatic Automatic diesel MXO/MYD HD 6-speed

OPTION

RATIO

CODE GU6

3.42

GU6

3.42

GHO

3.54

NOTE: Emission type must be ordered FE9 - Federal YF5 - California NG1 - Northeast States

SEATS AND INTERIOR TRIM SEAT OPTIONS EBONY COLOR STANDARD Front: Vinyl trimmed high-back buckets, inboard armrests and reclining AR7 93W Medium Pewter Rear: Vinyl trimmed bench seat and split four passenger last seat OPTIONAL Front: Bucket with custom cloth trim, head restraints and inboard armrest AS5 93G Medium Pewter Rear: Bench seats with custom cloth (head restraints not available on rear bench seats) NOTE: Vinyl trim only available in Medium Dark Pewter

EMISSIONS FE9

MUST BE SPECIFIED

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State

YF5 California emissions. Use for ordering vehicles that will be registered in California. NE1 CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8

Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Massachusetts, Maryland, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State.

NC7

Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles”

NB9

Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California.

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator.

2014 Chevrolet Municipal Vehicles Technical Manual

4 | EXPRESS

TRANSPORT VAN 1LS & 2LS OPTIONS Available options

C69 Air conditioning, rear - Requires TR9 auxiliary lamps, includes C36 rear heater, U80 digital compass and KG3 145-amp alternator. KG3 Alternator, 145-amps - Included with C69 rear air conditioning. US8 Audio system - AM/FM stereo with CD/MP3 player, seek-and-scan, digital clock, auto-tone control, Radio Data System (RDS), two front door speakers and two rear door speakers and two in the sound bar, requires ZQ2 Convenience Package. U1C Audio system - AM/FM stereo with CD player, seek-and-scan, digital clock, theftlock, random select and 2 front door speakers, not available with NP5 leather wrapped steering wheel. USR Audio system Feature - USB port, included and only available with US8 AM/FM stereo with MP3 compatible CD player UYS Audio system With Navigation - AM/FM stereo with MP3 compatible CD/DVD player and navigation, USB Port, seek-and-scan, digital clock, auto-tone control Radio Data System (RDS), speed-compensated volume and TheftLock, not available with UEO OnStar delete UA1 Battery - Heavy-duty 770 CCA, maintenance-free with rundown UPF Bluetooth for phone10 - Personal cell phone connectivity to vehicle audio system, requires UE1 OnStar8, US8 AM/FM stereo with MP3 compatible CD player, U2K XM Radio9, NP5 leather-wrapped steering wheel, W1Y steering wheel controls, ZQ3 Convenience Package. Not available with UE0 OnStar delete on UYS V37 Bumpers - Front and rear chrome with step pad (included with ZR7 Chrome Appearance Package) ZR7 Chrome APPEARANCE PACKAGE - Includes V37 front and rear chrome bumpers with step-pad and V22 chrome grille with dual composite halogen headlamps V10 cold climate package - Includes engine block heater (includes KO8 if ordered with 6.6L turbo diesel) U80 Compass - 8-point digital located in the Driver Information Center, included and only available with C69 rear air conditioning. BA3 Console - Deluxe with swing-out storage bin ZQ3 Convenience Package - Tilt-wheel and cruise control K34 Cruise control - Included and only available with ZQ3 Convenience Package, tilt-wheel and cruise control. C49 defoggers - Rear window, requires tinted glass Ya2 door - Sliding passenger, side (requires C69 rear air conditioning) AU3 Door locks - Power with lock-out protection (included with ZQ2 Convenience Package) KO5 ENGINE BLOCK HEATER - Included and only available with V10 Cold Climate Package which requires L96 Vortec 6.0L V8 SFI FlexFuel2 engine B30 Floor covering - Full-floor color-keyed carpeting with front and rear rubberized-vinyl floor mats V22 Grille - Chrome with dual composite halogen headlamps (included and only available with ZR7 Chrome Appearance Package) KO8 HEAT GENERATOR - Auxiliary-fuel-operated supplemental heat source to cooling system to improve heat out put (included with V10 and LGH Duramax 6.6L turbo diesel) C36 Heater, rear auxiliary - Included with C69 rear air conditioning. UF3 High idle switch - Requires *G33*06, L96 Vortec 6.0L V8 SFI or 6.6L V8 L6H diesel engine and ZQ3 Convenience Package. Tr9 Lamps - Lamps, auxiliary with reading and underhood lamps, requires C69 rear air conditioning. Includes DH6 driver and front passenger visor vanity mirrors De5 mirrors - Outside, left hand and right hand, remote control electric, manual foldaway with defog feature (requires zq2) UD7 Rear park assist - Requires UM7 AM/FM stereo, US8 AM/FM stereo with CD/MP3 player or UYS AM/FM stereo with MP3 compatible CD/DVD player and navigation UVC Rear Vision Camera - Display integrated into rearview mirror, integrated into navigation screen when UYS AM/FM stereo with MP3 compatible CD/DVD player and navigation is ordered ATG REMOTE KEYLESS ENTRY - Includes 2 transmitters and remote panic button BTV remote vehicle starter system- Includes remote keyless entry, 2 transmitters (requires ATG) Zp3 seats - 15-passenger seating (2/3/3/3/4 seating configuration) As5 seats - Front bucket with custom cloth trim, head restraints and inboard armrests, requires (**G) interior trim. When ordering a seating arrangement that includes rear seats, includes rear bench seats with custom cloth trim. Head restraints are not available on rear bench seats DT4 Smoker's Package - Includes ash tray and lighter Z82 trailering special equipment - Heavy-duty, included platform trailer hitch and 7-wire harness DH6 Visors - Driver and front passenger, padded with cloth trim and dual vanity mirrors, illuminated on passenger-side, included and only available with TR9 auxiliary lamps 40P Wheel finish, Painted White - White-painted wheels in lieu of standard Gray-painted wheels P03 Wheel trim - Chrome center cap

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator. 8. Visit OnStar.com for coverage map, system limitations and details. 9. XM Radio requires a subscription, sold separately by XM after the trial period. Not available in Canada, Alaska or Hawaii. For more information, visit gm.xmradio.com. 10. Go to gm.com/bluetooth to find out which Bluetooth phones are compatible with the vehicle.

2014 Chevrolet Municipal Vehicles Technical Manual

EXPRESS TRANSPORT VAN 1LS & 2LS | 5 AVAILABLE EXTERIOR COLORS GAN

GBV

GWX

25U

41U

47U

50U

74U

9W3

*Silver Ice Metallic New

* Brownstone Metallic New

*Cyber Gray Metallic New

*Dark Blue Metallic

**Black

*Dark Green Metallic

Summit White

**Victory Red

**Wheatland Yellow

NOTE: * Additional Charge

** Not avaialble with B46 rear body-colored halo trim

Actual colors may vary

SEO Paint Available WA#

COLOR DESCRIPTION

CODE

215D

Yellow



TBD

259L

Yellow



TBD

451N

Blue



TBD

478G

Yellow



TBD

519F

Galaxy Silver Metallic



TBD

529F

Bronzemist



TBD

811K

Berry Red



TBD

5456

Yellow



TBD

7927

Green



TBD

7941

Green



TBD

8867

Silver Metallic



TBD

9015

Woodland Green



9V5

9403

Doeskin Tan



9V9

9414

Yellow



TBD

9417

Tangier Orange



9W4

Actual Color May Vary NOTE: • All normally body-colored non-sheet metal parts, will be Flat Black • SEO paint orders that contain less than five vehicles will be delayed until five unit minimum is received for batch production

2014 Chevrolet Municipal Vehicles Technical Manual

6 | EXPRESS

TRANSPORT VAN 1LS & 2LS – Specifications

GENERAL Model Model Drive

CG33406 CG33706 Rear-wheel



EXTERIOR (in./mm)

CG33406 1LS/2LS Regular Wheelbase

CG33706 1LS/2LS Extended Wheelbase

Wheelbase Overall length Body width Overall height Front bumper to axle Opening height, side door Opening height, rear door Opening width, sliding side door Opening width, rear door, at beltline Step up height, front door Step up height, side door Ground clearance, front Ground clearance, rear

135.0/3429 224.1/5692 79.2/2013 81.5/2070 39.7/1008 47.9/1217 49.4/1255 44.1/1120 57.0/1448 19.4/493 19.8/503 11/279 7.1/180

155.0/3937 244.1/6200 79.2/2013 82.8/2103 39.7/1008 47.9/1217 49.4/1255 44.1/1120 57.0/1448 19.4/493 19.8/503 8.8/224 7.7/196

39.8/1011 38.4/975 38.5/978 37.6/955 – 68.8/1748 68.6/1742 65.8/1671 69.1/1755 – 65.5/1664 65.6/1666 63.3/1608 65.7/1669 – 41.3/1049 36.3/922 36.6/930 36.6/930 – 27.8/706 126.2/3205 153.6/3901 50.4/1280 51.8/1316

39.8/1011 38.4/975 38.5/978 37.6/955 37.6/955 68.8/1748 68.6/1742 65.8/1671 69.1/1755 62.9/1598 65.5/1664 65.6/1666 63.3/1608 65.7/1669 62.9/1597 41.3/1049 36.3/922 36.6/930 36.6/930 34.1/866 30.1/765 146.0/3708 173.6/4409 50.4/1280 51.8/1316

INTERIOR (in./mm) Head room, 1st row Head room, 2nd row Head room, 3rd row Head room, 4th row Head room, 5th row Shoulder room, 1st row Shoulder room, 2nd row Shoulder room, 3rd row Shoulder room, 4th row Shoulder room, 5th row Hip room, 1st row Hip room, 2nd row Hip room, 3rd row Hip room, 4th row Hip room, 5th row Leg room, 1st row Leg room, 2nd row Leg room, 3rd row Leg room, 4th row Leg room, 5th row Ground to top of rear load floor Load floor length, to front seat, at floor Load floor length, to engine cover, at floor Inside width, between wheelhousing Cargo area height

Published dimensions indicated are without optional equipment or accessories. Additional accessories or equipment order at customer's request can result in a minor change in these dimensions.

CAPACITY Curb weight, lbs.3 (kg) Cargo volume, regular, with seats, cu. ft.3 (liters) Cargo volume, regular, with seats removed, cu. ft.3 (liters) Payload 6, lbs. (kg) Gross Vehicle Weight Rating5 (GVWR), lbs. (kg) Front Gross Axle Weight Rating (FGAWR), lbs. (kg) Rear Gross Axle Weight Rating (RGAWR), lbs. (kg) Seating capacity (front/2nd/3rd/4th)

6087/2761 6406/2906 92.1/2608.3 127.2/3602.3 216.2/6122.8 252.8/7159.3 3461/1570 3142/1425 9600/4354 9600/4354 4600/2087 4600/2087 6084/2760 6084/2760 2/3/3/3 2/3/3/3/4

ENGINE 1LS STD Type V8 Displacement: liters/cu. in. 4.8/293 Horsepower/rpm 280@5200 Torque lb.-ft./rpm 295@4600 Fuel system SFI Compression ratio – Exhaust Single Minimum recommended fuel octane 87 Fuel tank capacity (gallons/liters) 31/117.3

1LS OPT

2LS STD

V8 6.0/366 323 @ 4600 373 @ 4400 SFI 9.6:1 Single 87 31/117.3

V8 6.6/403 260 @ 3100 525 @ 1600 Turbo Diesel – Single – 31/117.3

6-speed

6-speed

3.42

3.54

Maintenance free 78 12 69 600 115

Maintenance free 78 12 63 Dual 770* 115

Disc/Disc 12.8 x 1.50 13.0 x 1.14

Disc/Disc 12.8 x 1.50 13.0 x 1.14

Disc/Disc 12.8 x 1.50 13.0 x 1.14

All-season LT245/75r16

All-season LT245/75r16

All-season LT245/75r16

Steel 16" x 6.5"

Steel 16" x 6.5"

Steel 16" x 6.5"

TRANSMISSION Automatic heavy-duty

6-speed

AXLE



Ratio

3.42

BATTERY



Type Maintenance free BCI group size 78 Volts 12 Amp hour rating 69 Cold cranking-amps @ 0°F (-18°C) 600 Reserve capacity @ 80°F (27°C) 115 *Standard on 2LS with 6.6L Turbo Diesel

BRAKES ABS hydra-boost Front size Rear size

TIRES Type Size

WHEELS Type Size

CHASSIS Frame Full length Full length Full length boxed frame boxed frame boxed frame Front suspension Independent with Independent with Independent with coil spring and coil spring and coil spring and stabilizer bar stabilizer bar stabilizer bar Rear suspension Hypoid driver axle Hypoid driver axle Hypoid driver axle w/multi-leaf springs w/multi-leaf springs w/multi-leaf springs Steering type Speed sensitive Speed sensitive Speed sensitive (evo), variable ratio, (evo), variable ratio, (evo), variable ratio, integral power integral power integral power Steering ratio (center/stop) 17.2:1 17.2:1 17.2:1

ALTERNATOR Type Standard with rear AC Amps Amps @ idle

TBD *105 TBD

TBD *105 TBD

* Without Rear air conditioning. 145-amp required with rear air conditiong 3. Cargo and load capacity limited by weight and distribution. 5. Gross Vehicle Weight Rating (GVWR). When properly equipped, includes vehicle, passengers, cargo and equipment. 6. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo.

2014 Chevrolet Municipal Vehicles Technical Manual

AD244 145 59

AIR BAGS FAQ | 7 Can specialty vehicle equipment (e.g. radar devices, video cameras, computers, meters, radio trees, shotguns, etc.) still be mounted in cars with passenger side air bags? Yes, but care must be taken to mount the equipment outside of the deployment zone. Air bags inflate with great force and will interact with any object in the deployment zone. Therefore, to reduce the risk of injury to vehicle occupants, GM recommends that the air deployment zone be kept free of any equipment. If a piece of equipment were to become dislodged it could strike an occupant in the vehicle and result in injury. The likelihood of an object becoming dislodged is influenced by many factors, including the proximity of the object to the inflatable restraint, the size and shape of the object, and the means by which the object is secured to the vehicle. In addition to these factors, the trajectory and velocity of a dislodged object can be influenced by the type and severity of vehicle crash. Objects that are in the deployment zone, but do not become dislodged by an inflating air bag can still affect the performance of the air bag. For example, such objects could tear the fabric or affect the shape of the air bag, thus reducing the ability of the bag to provide restraint. Is it possible to shield equipment that is installed in the passenger side frontal air bag deployment zone in a manner that will allow full and safe air bag deployment? Due to the complexity of influencing variables, GM is unable to evaluate the potential for shielding expected equipment configurations in all accident scenarios in order to assure that the air bag performance would be unaffected. While shielding may protect certain equipment from being damaged or dislodged, it may also negatively affect the inflation characteristics of the air bag. The air bag’s shape, inflation angle, fold pattern, and inflation rate and pressure are developed to maximize the protection capability of the inflatable restraint system. Therefore, GM cannot recommend the placement of any equipment in the deployment zone, even if it is shielded to protect it from damage. Front air bag systems and instrument panel mounted equipment. Passenger air bags in GM vehicles deploy in different ways depending upon the type of vehicle and the particular instrument panel design. In some vehicles, the passenger air bag deploys through a discrete door located on the top surface of the instrument panel (top-mount air bag systems). In other vehicles, such as the Chevrolet Tahoe, the passenger air bag deploys through a discrete door mounted on the vertical rearward surface of the instrument panel, above the glove box door (mid-mount air bag system). With these types of topmount and mid-mount passenger air bag systems, the top pad of the instrument panel remains in place during deployment. Some GM passenger air bag systems, like the system in the Chevrolet Impala, deploy from beneath the instrument panel top pad. These are considered 3/4-mount air bag systems with a “deployable top pad.” The entire instrument panel top pad is the “deployment door” from under which the inflating air bag emerges. When an air bag deployment is commanded, the forces from the inflating passenger air bag push up on the instrument panel top pad, releasing special fasteners across the rearward edge of the top pad. This allows the top pad to rotate upward so that the passenger air bag may emerge. The top pad rotates upward to open widest at the right hand side, and is usually forced upward into contact with the windshield on the right hand side of the vehicle during a deployment.

Instrument panel top mounted special equipment, such as a radar antenna and control unit or video camera must be positioned to the left of the vehicle center line. This equipment must be mounted as low as possible and securely fastened to the top pad to avoid being dislodged in the event of a crash and possible air bag deployment. In the process of securely fastening special equipment to the top, DO NOT fasten down the top pad itself to any other vehicle component such as the cluster trim plate. As described above, the top pad rotates upward during a deployment. In order to enable the proper deployment of the passenger air bag, specialty equipment installation MUST NOT PREVENT the top pad from rotating upward during deployment. Location and attachment of special equipment should minimize added resistance or interference to upward rotation of the top pad during deployment. Side-Impact Air Bags for crashes to the vehicle sides. The air bag system in your police vehicle includes includes roof rail mounted Head Curtain side air bags.. The vehicle is also equipped with seat back mounted upper body air bags located on the outboard side of the driver and front passenger seat backs. Together the Head Curtain and seat-mounted side air bags are intended to protect the head and upper body in the event of a side crash. Some vehicles may also be equipped with an optional air bag, mounted on the inboard side of the driver seat back. Can Specialty Vehicle Security Barriers be mounted within the side air bag deployment zones? No. The side air bags inflate extremely fast because of the nature of side crashes to the vehicle. Mounting a security barrier behind the front seats with the ends placed within the side air bag deployment zones will result in unintended interaction between the barrier and the inflating side air bags. To reduce the risk of injury to the vehicle occupants, GM recommends that the side air bag zones be kept free of any customer installed equipment. Customer furnished equipment installed to the vehicle roof. Your police vehicle is designed with an interior roof cover system which includes internal components for the interior lamps and wiring. The roof system may also include side air bag components. Inflation devices may be mounted on the vehicle roof side behind the rear doors as well as air bag tethers retained to the windshield pillars. Care must be taken to avoid damage to these components or interference with their operation when installing roof mounted equipment such as emergency lamps and communication antennas. Recommended GM service procedures must be followed to remove and re-install the instrument panel top pad to ensure that the top pad will release properly in the event of a passenger air bag deployment. On the right half of the top pad closest to the passenger air bag module, GM recommends that no equipment be mounted. When mounting equipment on the driver side of the top pad, GM recommends that the total mass of the top pad mounted special equipment not exceed 8 pounds (3.6 kilograms), since some top pads tend to rotate about the left end. Fasteners used to secure special equipment to the instrument panel top pad, the windshield glass, or to the windshield upper frame (header), should be selected to ensure that these devices will remain attached during a vehicle crash and possible air bag deployment.

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

8 | AIR

BAGS FAQ

Can the installation of push bumpers on the front end of the vehicle affect the deployment of the air bag?

I've heard that a deployed air bag produces whet appears to be smoke, is the air bag hot?

General Motors is not aware of adverse effects during crash events from the many push bumpers thai have been installed on GM police vehicles. Because there are many styles of push bumpers available with varying crash characteristics, installation of push bumpers may or may not affect deployment timing of the air bags. Push bumpers should be mounted to avoid modifying the vehicle structure and interfering with the front air bag sensors mounted on the upper radiator support cross member

After the bag has deployed in a crash, the air bag itself will not be hot to touch. Some components within the air bag module will be hot for a short time. A small amount of smoke coming from a deployed air bag module is normal and should not be cause for concern.

Two front impact sensors are installed in General Motors vehicles. Do not relocate or disconnect the front sensors. The location and orientation of the front sensors are critical for correct operation of the air bag system. Avoid mounting components on or near the sensors. Push bumper styles with vertical pushing members that are in foreaft alignment with the front air bag sensors are not recommended. When should an air bag inflate? The driver's and right-front passenger's frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system's designed "threshold level." In addition, your vehicle has “dual stage” frontal air bags which tailor the the amount of restraint according to crash severity. For moderate frontal impacts, the air bags inflate at a level less than full deployment. For more severe frontal impacts, "dual stage" frontal air bags deploy at full levels. If the front of your vehicle goes straight into a wall that doesn't move or deform, the threshold level of the reduced deployment is about 12 to 16mph (19 to 15 km/h), and the threshold level for a full deployment is about 18 to 24 mph (29 to 28.5 km/h). The threshold level can vary, however, with specific vehicle design, so that it can be somewhat above or below this range. If your vehicle strikes something that will move or deform such as a parked car, the threshold level will be higher. The driver's and right-front passenger's frontal air bags are not designed to inflate in rollover, side impacts, or rear impacts, because inflation would not help the occupant. Seat mounted side impact air bags are designed to inflate in moderate to severe side crashes. The side impact air bags will inflate if the crash severity is above the designed "threshold level." The threshold level can vary with specific vehicles design. The side impact air bags are not designed to inflate on frontal or near-frontal impacts or rear impacts, because inflation would not help the occupant.

Also, when the nitrogen gas is vented out of the air bag, small particles from inside the bag are also vented into passenger compartment. These airborne particles look like smoke and some particles are deposited as residue on and around the air bag. I've heard that the dusts that are released into the passenger compartment from the air bag are harmful, is this true? For most people, the only effect the dusts will produce is some irritation of the throat and eyes, and that is only if the occupant remains in the vehicle for many minutes after the air bag deployment with no ventilation and windows closed. However, some people with asthma may develop an asthmatic attack from inhaling the dusts. If this happens, they should first treat themselves the same way their doctor has advised them to treat any other asthma attack, and then immediately seek medical treatment. Can the air bag system be re-used? No, The air bags are designed to inflate only once. After inflation some new parts will be required. These will include the air bag module and possibly other parts. (A competent service technician with access to the vehicle's service manual and the required tools should replace the required components after a deployment crash.) If my vehicle has air bags, why should I have to wear my safety belt? Air bags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts not instead of them. Every air bag system ever offered for sale has required the use of safety belts. Even if you're in a vehicle that has air bags, you still have to buckle up to get the most protection. That's true not only in frontal collisions but especially in side and other collisions.

Roof rail mounted head-curtain air bags are designed to inflate in moderate to severe side crashes. In addition, certain vehicles have head-curtain air bags which are also designed to inflate in situations where an impending rollover condition is identified by the vehicle's rollover sensing system and/or frontal or near-frontal impacts if the crash severity is above the designed "threshold level". Safety belt pretensioners at the driver and front passenger seat positions are designed to deploy in frontal, near-frontal, side, and rear crashes that exceed the "threshold level" of crash severity to help reduce slack in the safety belt Safety belt pretensioners will also deploy in impending rollover situations. How long will the air bag remain inflated? It takes approximately 1/20th of a second to fully inflate the frontal air bags. This is faster than the blink of an eye. The air bags begin to deflate immediately, helping to stop the occupants more gradually.

2014 Chevrolet Municipal Vehicles Technical Manual

EXPRESS TRANSPORT VAN 1LS & 2LS – AIR BAG DimensionS | 9

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

10 | EXPRESS

TRANSPORT VAN 1LS & 2LS – AIR BAG DimensionS

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

Anti-lock braking system FAQ | 11 GM offers Anti-Lock Brake Systems as standard or optional on all North American passenger vehicles and light truck lines. The computerized Anti-Lock Braking System (ABS) is designed to keep the vehicle’s wheels rotating as the brakes are applied to assist the driver in achieving a controlled stop. Sensors monitor how fast the wheels rotate and feed the data continuously to the ABS computer. The vehicle’s brakes slow each wheel as the brake pedal is applied. However, when ABS is activated due to road conditions, the system repeatedly releases and applies pressure to the brakes. The wheels can keep rolling, thus retaining steering ability and enhanced stability while providing a higher braking force on most surfaces than a locked wheel provides. How exactly does ABS work? In cars without ABS, hitting the brakes can cause the wheels to lock, leaving you unable to steer the vehicle until you decrease the pressure so the wheels can roll again. With an ABS, as you apply the brakes, the ABS computer monitors the wheel speed sensor information. If the computer senses that a wheel is approaching lock up, it sends a signal to the hydraulic modulator to reduce, then to reapply, brake pressure several times a second for as long as you maintain firm pressure on the brake pedal. The process is much like the threshold braking technique used with conventional brakes. However, ABS does it much faster and more accurately than any driver can, leaving you free to focus on steering away from obstacles.

Does ABS reduce stopping distances?

Should I drive an ABS equipped vehicle differently than I would drive a vehicle with conventional brakes? Most of the time, under normal driving circumstances, there is no difference, and you should always drive with the same caution and care. It is important to realize that ABS only makes a difference when it is activated—when you have to brake hard—and that would only be when the computer senses that a wheel is approaching lock up. When ABS activates keep steady pressure on the brake pedal and then let the ABS work for you. Don’t pump the brakes or try to ­find the threshold. Simply hold the brake pedal down and steer if necessary to avoid an obstacle.

Is ABS always active? ABS is always available, but not always activated. ABS is activated only when the brake pedal is applied and the computer detects an impending wheel lock condition.

Can older cars be retrofitted with ABS? No! The brake system is one of the most important features on any passenger vehicle. Several products, which tap into the master cylinder and/or brake system performance, are being sold in the aftermarket. Some of these products imply performance similar to new vehicle anti-lock brake systems. However, contrary to their claims, add-on systems, which deplete fluid from the master cylinder on brake apply may actually increase a vehicle’s stopping distance. This may cause the vehicle to fail to comply with Federal brake standards.

Does ABS always activate at the same speed? No, the system operates when the computer detects wheel lockup, at any speed above 8 mph.

Yes, in braking situations where the wheels on a non-ABS equipped vehicle would lock up, ABS will generally provide shorter controlled stopping distance. The amount of improvement in stopping distance depends on many factors, including the road surface, severity of braking, initial vehicle speed, etc. On some surfaces, such as gravel roads, braking distances can be longer, but you will still have the control benefits of ABS. The important capability of ABS is control. ABS provides improved vehicle steerability and stability when braking.

Will ABS wear out a vehicle’s brakes sooner?

What can affect the ABS advantage?

Do Federal Safety Standards mandate ABS?

It is important that you follow the maintenance schedule recommended in the owner’s manual of the vehicle, tires should be at their proper inflation level, the brake pads should be checked regularly, etc. While driving, you should sit comfortably, so that your hips are back in the seat and your knees are bent, even while braking. Your foot should be positioned so that your heel is on the floor and your toes are secure on the lower half of the pedal. And, though ABS may reduce stopping distance, remember: The faster you go, the longer it takes you to stop. Keeping a safe distance between you and the vehicle in front of you is always necessary, even with ABS.

A properly maintained brake system will be unaffected by ABS operation under typical driving conditions.

Are there different types of ABS? Yes, there are rear wheel anti-lock systems (RWAL) used on some trucks and four-wheel ABS available on cars and trucks.

No. Federal standards establish minimum braking performance requirements that all vehicles must meet, but do not specify how they should be met. It should be noted that even a vehicle with failed ABS meets the Federal safety standard for stopping distances.

Will a tire size change affect ABS? Use of tires other than original equipment may affect ABS performance. Owners should consult and follow the recommendations contained in the vehicle owner’s manual regarding replacement tire size. NOTE: ABS will work with original equipment spare tire or tire

What happens if ABS becomes inactive?

chains. However, performance is reduced.

The ABS electronic control unit has on-board diagnostic capability. If a fault is detected, the vehicle will revert to the base brake system, and the ABS telltale on the dash will be illuminated. Should this happen, the vehicle should be taken to a dealership for repair as soon as possible.

Do insurance companies give a discount for ABS?

How do I use ABS? Depress and hold the pedal. DO NOT PUMP THE BRAKES (that prevents the system from working). Just hold the brake pedal down and let the ABS work for you. You may feel the brake pedal vibrate, or you may notice some noise, but this is normal as the system works for you.

Yes, many insurance companies give discounts that range from 5% to 10%. In the states of New York and Florida all insurance companies are required to give an ABS discount of 5% on certain coverages such as bodily injury, property damage, collision, and personal injury protection. In other states the discount varies from insurance company to insurance company. When buying auto insurance, always ask your insurance agent if his/her company gives a discount for vehicles equipped with antilock brakes.

NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

12 | Anti-lock

braking system and Stabilitrak

IMPORTANT DRIVING SAFETY TIPS A. A lways maintain a safe

following distance. ABS does not

allow you to stop on a dime. (Generally a 2-second following distance is considered safe in ideal conditions.) Watch the vehicle in front of you pass a fixed marker (such as a sign). Count seconds—one-thousand-one, one-thousand-two-until your front bumper reaches the marker. If you do not count out two seconds, then you are too close to the vehicle in front of you. Also, if the roads are wet or icy, or visibility is poor, you should increase your following distance.

B. A lways drive carefully—

especially on slippery surfaces. ABS cannot create friction between the tires and the road surface, it can only give the driver the maximum advantage of the existing adhesion. If the vehicle is traveling on a surface with no adhesion, the best ABS in the world cannot provide a shorter stopping distance or good steering.

C. It is a good idea to practice an

ABS activated stop and get the feel of the brake pedal. However, please make sure it’s at a safe time with no obstacles in your path. And you only really need to try it once or twice to know what happens.

Electronic Stability Control systems (StabiliTrak) Q. How does StabiliTrak work? StabiliTrak systems help drivers maintain control of their A. StabiliTrak has the ability to apply control forces to vehicles, especially during emergency lane changes or the vehicle independent of the driver. StabiliTrak uses avoidance maneuvers. StabiliTrak uses various sensors, sensors to continuously compare the path indicated by such as steering wheel angle, wheel speed, yaw velocity, the steering wheel position to the vehicle’s actual path. If etc., to detect any difference between the path requested a discrepancy is detected, StabiliTrak selectively controls by the steering wheel position and vehicle’s actual path. vehicle brakes and engine torque to create a yaw moment When appropriate, the system selectively controls brakes, that helps restore the vehicle’s actual path to the path engine power, and even suspension settings to enhance indicated by the steering wheel position. StabiliTrak has control of the vehicle’s direction and help keep it on course. the ability to help correct both understeer (where the Independent studies conducted by the National Highway vehicle is not turning as much as the steering wheel Traffic Safety Administration, the Insurance Institute for position indicates) and oversteer (where the vehicle is Highway Safety, and others have found StabiliTrak to be turning more than the steering wheel position indicates). highly effective in reducing vehicle crashes. General Motors The illustration at right shows how selective braking at a offers StabiliTrak systems on many of its passenger car particular wheel can create a compensating yaw moment and light truck models. to help restore the vehicle’s actual path to the path See your owner's manual for additional information about indicated by the steering wheel position. the operation of StabiliTrak. Q. Will a tire change affect StabiliTrak? Q. How do I use StabiliTrak? A. Use of tires other than original equipment may affect A. S  tabiliTrak operates independently of the driver. You StabiliTrak performance. StabiliTrak is designed to make should continue to drive your StabiliTrak equipped the best use of available traction. The performance vehicle with caution and care. GM’s StabiliTrak system, characteristics of the original equipment tires are part of StabiliTrak, is designed to be as seamless as possible in the overall system effectiveness. When you replace tires operation, to be part of the overall vehicle response and to check the recommendations in your owner's manual. On make a good vehicle better GM vehicles, the original equipment tires have a “TPC” (Tire Performance Criteria) code on the sidewall. Replacing the tires with the same “TPC” code will help assure proper StabiliTrak performance.

2014 Chevrolet Municipal Vehicles Technical Manual

SUBURBAN COMMERCIAL FLEET 1FL | 1

Updates for 2014 New Features • Concord Metallic

Deleted

• • • • • • • • • •

Blue Ray Metallic (GXH) Black Granit Metallic (58U) Specialty Paint Wheatland Yellow (253A) Specialty Paint Dark Toreador Red (334D) Specialty Paint Dark Blue Metallic (722J) Specialty Paint Blue (5665) Specialty Paint Green (7941) Specialty Paint Woodland Green (9015) Specialty Paint Yellow (9414) No 3/4 ton models for 2014 model year

2014 Chevrolet Municipal Vehicles Technical Manual

2 | SUBURBAN

COMMERCIAL FLEET 1FL

NOTE: This vehicle is NOT designed nor intended for use IN HIGH SPEED EMERGENCY VEHICLE OPERATIONS

Model availability Cc10906 Ck10906

Rear-wheel drive 1/2 ton 4-wheel drive 1/2 ton

Standard equipment summary Warranty 3 years / 36,000 miles bumper-to-bumper (whichever comes first, see dealer for details) 5 years / 100,000 miles limited powertrain (whichever comes first, see dealer for details)

Interior features Air conditioning

Tri-zone manual climate control with individual climate settings for driver and right-front passenger; includes auxiliary rear air conditioning and heat Assist handles Front passenger and second row outboard; front passenger assist handle is deleted when passenger side spotlamp is ordered Console, overhead Mini with map lamps Cruise control Electronic with set and resume speed Dome Lamps Interior dome lamp, driver and passenger side door switch with delayed entry feature, cargo lamps, remote keyless entry activated illuminated entry and map lamps in front and second seat position Floor covering Black rubberized-vinyl (not available with b39 cargo mat) Glass Deep tinted (all windows except light-tinted glass on windshield, driver and front passenger side glass) Mirror Inside rearview auto-dimming OnStar Delete option available Power outlets 12-volt, two located on instrument panel and one in rear cargo area Radio am/fm stereo with mp3 compatible cd player, seek-and-scan, digital clock, auto-tone control, Radio Data System (rds), six speakers, speed-compensated volume and theftlock Restraint system Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, rollover sensor, dual head curtain air bags1 for first and second row outboard occupants and front seat back mounted thorax-pelvic air bags1; includes 3rd row outboard seating position when 3 passenger third row 50/50 split-bench option AS3 is ordered Seat, front Split-bench 40/20/40 with custom cloth 3-passenger, includes 6-way power driver seat adjuster with manual lumber control, driver and passenger manual reclining, outboard head restraints, center fold-down covered storage in armrest, center lower seat cushion storage and rear storage pockets Seat, rear Custom cloth 60/40 split folding bench with center armrest Seat, third row 50/50 split-bench 3-passenger with premium cloth, safety belts, removable seat Speedometer/cluster 120 mph analog speedometer, trip odometer, fuel level, volt meter, engine temperature oil pressure and tachometer Steering column/wheel Tilt-wheel, adjustable, with brake/transmission interlock Theft deterrent Vehicle theft PASS-Key® III+, content theft deterrent is disabled (to enable content theft deterrent option ua6 must be ordered) Visors Padded with cloth trim, extends on rod; driver and front passenger illuminated vanity mirrors Warning toneS Headlamp on, key-in-ignition, driver and right-front passenger safety belt unfasten and turn signal on Window operation Power with driver express-down and lockout features

1. H  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

SUBURBAN COMMERCIAL FLEET 1FL | 3 Exterior features Assist steps

Black, mounted between front and rear wheels

Defogger

Electric, rear window

Door handles

Black

Door locks Power programmable with lockout protection, door lock cylinder no longer available on passenger front door and rear liftgate Fascia, front

Color – keyed (Black when special paint is ordered)

Fascia, rear

Color – keyed (Black when special paint is ordered)

Headlamps

Dual halogen composite with automatic exterior lamp control and flash-to-pass feature

Keyless entry Includes two transmitters Keys

Single two-sided, random code, for ignition and drivers door only

Luggage rack

Roof mounted Black side rails (center rails and luggage rack delete are available)

Mirrors

Outside heated power-adjustable, manual-folding, Black

Rear liftgate

Liftgate/liftglass, with rear window washer and wiper (power liftgate not available)

Recovery hooks

Two front, Black (Chrome only available on LTZ)

Windshield wipers

Intermittent wet-arm with flat blade and pulse washers

Chassis features Alternator 160-amp Battery 660 CCA, maintenance-free, rundown protection and retained accessory power Brakes 4-wheel antilock, 4-wheel disc, vac power Engine See engine, transmission and axle chart on page 4 Frame Modular with hydro formed frame rails Fuel tank CAPACITY 31 gallon (117.3 liters) Oil coolers Auxiliary transmission oil cooler, heavy-duty air-to-oil (requires 3.42 axle ratio on 1/2 ton models) Stabilitrak Vehicle stability control system with proactive roll avoidance Steering Power, rack and pinion Suspension, front Coil-over-shock with stabilizer bar Suspension, rear Multi-link with coil springs Tires See tire and wheel chart on page 5 Tire pressure monitor CHECK TIRE PRESSURE will show on Driver Information Center (no sensor in spare tire) tire, Spare See tire chart on page 5 tire, Spare carrier Lockable outside, winch-type mounted under frame at rear Trailering equipment Heavy-duty includes trailering hitch platform, 7-wire harness with independent fused trailering circuits mated to a 7-way sealed connector and vr4 2-inch trailering receiver. Electronic trailer sway control and hill start assist Transfer case Active single-speed, electronic autotrac with rotary controls, does not include Neutral (N). Cannot be dinghy towed, requires GU4 3.08 rear axle. Not available on 2WD models Transmission 6-speed automatic, see engine, transmission and axle chart on page 4 Wheels See wheel and tire chart on page 5

2014 Chevrolet Municipal Vehicles Technical Manual

4|

SUBURBAN COMMERCIAL FLEET 1FL C ommercial fleet package option 1 FL ENGINE/AXLE S = Standard Equipment A = Available – (dashes) = Not Available

TRANSMISSION AXLE GVWR lbs. (kg)

MODEL

ENGINE

MYC 6-SPEED MYD 6-SPEED GU4 GU6 GT4 AUTOMATIC AUTOMATIC HD 3.08 3.42 3.73



CC10906 CK10906

C5Z 7200 (3266)

C6C C6P 7400 8600 (3357) (3901)

LMG Vortec 5.3L V8 SFI FlexFuel2 S — S A — S — — LC9 Vortec 5.3L V8 SFI FlexFuel2 S — S A — — S —

NOTE: E mission type must be ordered FE9 - Federal YF5 - California NG1 - Northeast States

TRAILERING SPECIFICATIONS

Automatic Transmission Ratings with Ball Hitch (LMG) Vortec (LC9) Vortec 5.3L 5.3L V8 SFI FlexFuel2 V8 SFI FlexFuel2



MODEL



Axle Ratio



CC10906 CC10906* CK10906 CK10906*

Maximum Trailer Axle Ratio Weight lbs.7 (kg)

3.08 3.42 3.42 — —

5100 (2313) 5600 (2540) 8100 (3674) — —

Maximum Trailer Weight lbs.7 (kg)

— — —

— — —

3.42 3.42

5500 (2495) 8000 (3629)

*with (K5L) heavy-duty Trailering Package

GCWR -

ENGINE/REAR RATIO COMBINATION WITH AUTO TRANS



ENGINE (LMG) Vortec 5.3L V8 SFI FlexFuel2 (LC9) Vortec 5.3L V8 SFI FlexFuel2 (L96) Vortec 6.0L Variable Valve Timing V8 SFI FlexFuel2

(GCWR) Gross Combination Weight Ratings lbs. (kg) 11000 14000* (4989) (6350) 3.08 3.42 — 3.42 — —

*with (K5L) heavy-duty Trailering Package

2. E85 is 85% ethanol and 15% gasoline. To see if there is an E85 station near you, go to www.gmaltfuel.com/e85-station-locator. 7. M  aximum trailer weight ratings are calculated assuming a base vehicle, except for any option(s) necessary to achieve the rating, plus driver. The weight of other optional equipment, passengers and cargo will reduce the maximum trailer weight your vehicle can tow.

2014 Chevrolet Municipal Vehicles Technical Manual

SUBURBAN COMMERCIAL FLEET 1FL | 5 Tires and wheels CODE QAN QJP

SIZE P265/70R17 P265/70R17

Spare Tires CODE ZRS 4JP

SIZE P265/70R17 P265/70R17

DESCRIPTION All-season On/off-road

CODE NX7 P46

SIZE 17" x 7" 17" x 7.5"

DESCRIPTION 4 – steel 4 – 5 spoke

Spare Wheels

CODE NZ4

SIZE 17"

Road Tires

DESCRIPTION All-season On/off-road

SIDE WALL USAGE Blackwall Standard Blackwall Optional

MODELS 1/2 ton 2 or 4WD 1/2 ton 4WD

SIDE WALL USAGE Blackwall Standard Blackwall Optional

MODELS 1/2 ton 1/2 ton (requires QJP tires)

Road Wheels

DESCRIPTION One – steel

SIDE WALL USAGE Steel Standard Aluminum Optional

MODELS 1/2 ton 1/2 ton

SIDE WALL USAGE MODELS Steel Standard 1/2 ton

NOTE: Polished forged aluminum, includes chrome center caps and steel spare

Seats and interior trim S = Standard Equipment A = Available -- (dashes) = Not Available



Interior Decor Level Seat Seat Seat Trim Ebony Light Light Type Code Cashmere/ Titanium/ Dark Dark Cashmere 1 Titanium1 Standard Front: 40/20/40 AZ3 Premium cloth 19C 33C — Commercial (1FL) reclining split-bench Available Front: 40/20/40 AZ3 Vinyl 19V — — Commercial (1FL) reclining split-bench Optional Front: high-back A95 Premium cloth 19C 33C — Commercial (1FL) reclining bucket



Interior Exterior Color Touch Up Ebony Light Titanium/ Dark Cashmere/ Solid Paint Code Paint Number Dark Titanium4 Light Cashmere4 Black 41U WA-8555 A A A Mocha Steel Metallic GHA WA-7065 A A A Summit White 50U WA-8624 A A A Silver Ice Metallic1 GAN WA-636R A A A Crystal Red Tintcoat1 89U WA-505Q A A A Concord Metallic1 GWU WA-103V A A A Champagne Silver Metallic GWT WA-102V A A A 1 - Extra Cost

2014 Chevrolet Municipal Vehicles Technical Manual

6 | SUBURBAN

COMMERCIAL FLEET 1FL

AVAILABLE EXTERIOR COLORS

GAN

41U

GHA

50U

89U

GWU

GWT

Silver Ice Metallic

Black

Mocha Steel Metallic

Summit White

*Crystal Red Tintcoat

*Concord Metallic (New)

Champagne Silver Metallic

NOTE: * Additional Charge

Actual colors may vary

SEO Paint Available WA#

COLOR DESCRIPTION

9260 Victory Red

CODE



Requires SEO 5T4

Actual Color May VAry NOTE: • All normally body-colored, non-sheet metal parts, will be Flat Black (except Victory Red non-sheet metal parts will match) • SEO paint orders that contain less than five vehicles will be delayed until five unit minimum is received for batch production

2014 Chevrolet Municipal Vehicles Technical Manual

SUBURBAN COMMERCIAL FLEET 1FL | 7 Available options W2D Accessory - Cargo net K47 air cleaner - High capacity Jl1 brake controller - Integrated trailer D07 console - Floor storage area and cup holders (included and only available with a95 front custom cloth bucket seats) Utq content theft alarm disable - Flashing lamps and horn warning Knp cooling - Auxiliary transmission oil cooler. (Included and only available with k5l Hd Trailerling Package7 on 1/2 ton) Kc4 cooling - External engine oil cooler (Included and only available with k5l Hd Trailerling Package7 on 1/2 ton) G80 differential - Heavy-duty locking rear K05 engine blOck heater B30 floor covering - Color-keyed carpeting (includes b58 color keyed floor mats) VAV floor mats, all weather - First and second row, requires B30 color-keyed carpeting. Not available with AZE front 40/20/40 split-bench on 2WD models. (LPO, dealer installed) VKN floor mats, all weather - Third row, requires B30 color-keyed carpeting and AS3 third row 50/50 split-bench seats. Not available with AZE front 40/20/40 split-bench on 2WD models. (LPO, dealer installed) T96 fog lamps - Front, halogen Anj glass - Non-deep tinted K5l heavy-duty trailering package7 - Includes auxiliary transmission oil cooler and external engine oil cooler, (Includes 3.42 ratio rear axle) V1k luggage rack center rails - Roof mounted, Black G63 luggage rack - Delete VLI Mat, rear cargo - Requires B30 color-keyed carpeting. Not available with ATD third row seat delete. (LPO, dealer installed) B58 mats - Color-keyed carpeted first and second row, removable (included and only available with b30 floor covering) Dpn mirrors - Outside heated power-adjustable vertical camper; manual-folding, extension and integrated turn signal indicators Ueo OnStar - Delete VBS remote, 2-way advanced - (LPO, dealer installed) Ap3 remote vehicle starter system - Includes remote keyless entry Ud7 rear parking assist - Ultrasonic with led display and audible warning (requires jf4 power-adjustable pedals) V76 recovery hooks - Front, frame mounted, Black (Chrome only available on LTZ) Trw roof mounted lamp - Provisions (included with vyu Snow Plow Prep Package ) Nzz skid plate package - Requires 4-wheel drive model, includes aluminum front underbody shield starting behind front bumper and running to first cross-member, protecting front underbody, oil pan, differential case and transfer case, frame-mounted shield, requires 4-wheel drive model UVD Steering wheel - Heated (standard on LTZ trim) NQH Transfer case - Active 2-speed electronic autotrac with rotary controls includes neutral position for dinghy towing, requires 4WD models

Special Equipment Options available 5t4 exterior body-colored parts - Victory Red with special paint wa9260; Victory Red painted front and rear fascias, rear liftgate handle and rear license plate applique, body side moldings and door handles. Required with Victory Red special paint WA9260 9n5 floor console delete - Deletes floor console and associated audio equipment that is included with premium cloth high-back buckets seats; requires: peg 1fl and RPO a95 bucket seats 8X1 Label, Fasten Safety Belts - On Left hand and right hand front door window glass 9g3 off-road suspension - Off-road suspension 4x4 commercial or low uplevel décor; includes z71, off-road suspension components, skid plate and high capacity air cleaner; does not include body side “z71” decals; requires: model k10906 option qjp p265/75r17 on-off road tires peg 1fl Suburban 1ls or 1lt Uplevel Package and a fleet or government type order 5t5 seats, cloth front vinyl rear - Vinyl 2nd row rear seats and cloth front seats; if as3 third row seat is ordered, it will be vinyl. Requires: az3 front custom cloth 40/20/40 bench seat or a95 front custom cloth high-back bucket seat, trim code 19d Ebony and peg 1fl 9s1 seats, driver and passenger front individual seats in vinyl trim - Derived from RPO ae7 40/20/40 split-bench with center 20% section removed; seats are manual, not power; does not include floor console; exposed floor areas will remain untrimmed; rear seats will also be vinyl trimmed; requires trim code 19v Ebony and peg 1fl

7. M  aximum trailer weight ratings are calculated assuming a base vehicle, except for any option(s) necessary to achieve the rating, plus driver. The weight of other optional equipment, passengers and cargo will reduce the maximum trailer weight your vehicle can tow.

2014 Chevrolet Municipal Vehicles Technical Manual

8 | SUBURBAN

COMMERCIAL FLEET 1FL

EMISSIONS -

MUST BE SPECIFIED

FE9

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State

YF5

California emissions. Use for ordering vehicles that will be registered in California.

NE1 CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8

Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Massachusetts, Maryland, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State.

NC7

Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles”

NB9

Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California.

2014 Chevrolet Municipal Vehicles Technical Manual

SUBURBAN COMMERCIAL FLEET 1FL | 9



Interior



Specifications (in./mm) Wheelbase Overall length Body width Overall height Head room, front Head room, center Head room, rear Shoulder room, front Shoulder room, center Shoulder room, rear Hip room, front Hip room, center Hip room, rear Leg room, front Leg room, center Leg room, rear Ground to top of rear load floor Load floor length, to front seat, at floor Load floor length, to center seat, at floor Load floor length, to rear seat, at floor Inside width, between wheelhousing Cargo area height Ground clearance, front Ground clearance, rear Front shock absorber diameter Front stabilizer bar diameter Rear shock absorber diameter Rear stabilizer bar diameter Turning diameter, curb-to-curb, ft. (m) Capacities lbs. (kg) Front axle Rear axle Curb weight Cargo volume3, cu. ft. (liters) Payload6 Gross Vehicle Weight Rating5 (GVWR) Front Gross Axle Weight Rating (FGAWR) Rear Gross Axle Weight Rating (RGAWR) Fuel capacity, approximate, gallon (liters) Seating capacity (front/center/rear)

CC10906 2WD 1/2 Ton

CK10906 4x4 1/2 Ton

130.0/3302 222.4/5649 79.1/2009 76.8/1951 41.1/1044 38.5/978 38.1/968 65.2/1656 65.2/1656 64.7/1643 60.3/1532 61.8/1570 49.4/1255 41.3/1049 39.5/1003 34.9/886 31.8/808 101.8/2586 69.6/1768 35.6/904 49.1/1247 41.4/1052 10.5/267 9.1/231 1.81/46 1.41/36 1.81/46 1.10/28 43.0/13.1

130.0/3302 222.4/5649 79.1/2009 76.8/1951 41.1/1044 38.5/978 38.1/968 65.2/1656 65.2/1656 64.7/1643 60.3/1532 61.8/1570 49.4/1255 41.3/1049 39.5/1003 34.9/886 32.6/828 101.8/2586 69.6/1768 35.6/904 49.1/1247 41.4/1052 10.5/267 9.1/231 1.81/46 1.41/36 1.81/46 1.10/28 43.0/13.1

3500/1588 4200/1905 5672/2573 137.4/3891.2 1528/693 7200/3266 3500/1588 4200/1905 31/117 3/3/03

3600/1633 4200/1905 5824/2642 137.4/3891.2 1576/715 7400/3357 3600/1633 4200/1905 31/117 3/3/03

NOTE: P ublished dimensions indicated are without optional equipment or accessories. Additional accessories or equipment ordered at the customer's request can result in a minor change in these dimensions. 3. Cargo and load capacity limited by weight and distribution. 5. Gross Vehicle Weight Rating (GVWR). When properly equipped, includes vehicle, passengers, cargo and equipment. 6. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo.

2014 Chevrolet Municipal Vehicles Technical Manual

10 | AIR

BAGS FAQ

Can specialty vehicle equipment (e.g. radar devices, video cameras, computers, meters, radio trees, shotguns, etc.) still be mounted in cars with passenger side air bags? Yes, but care must be taken to mount the equipment outside of the deployment zone. Air bags inflate with great force and will interact with any object in the deployment zone. Therefore, to reduce the risk of injury to vehicle occupants, GM recommends that the air deployment zone be kept free of any equipment. If a piece of equipment were to become dislodged it could strike an occupant in the vehicle and result in injury. The likelihood of an object becoming dislodged is influenced by many factors, including the proximity of the object to the inflatable restraint, the size and shape of the object, and the means by which the object is secured to the vehicle. In addition to these factors, the trajectory and velocity of a dislodged object can be influenced by the type and severity of vehicle crash. Objects that are in the deployment zone, but do not become dislodged by an inflating air bag can still affect the performance of the air bag. For example, such objects could tear the fabric or affect the shape of the air bag, thus reducing the ability of the bag to provide restraint. Is it possible to shield equipment that is installed in the passenger side frontal air bag deployment zone in a manner that will allow full and safe air bag deployment? Due to the complexity of influencing variables, GM is unable to evaluate the potential for shielding expected equipment configurations in all accident scenarios in order to assure that the air bag performance would be unaffected. While shielding may protect certain equipment from being damaged or dislodged, it may also negatively affect the inflation characteristics of the air bag. The air bag’s shape, inflation angle, fold pattern, and inflation rate and pressure are developed to maximize the protection capability of the inflatable restraint system. Therefore, GM cannot recommend the placement of any equipment in the deployment zone, even if it is shielded to protect it from damage. Front air bag systems and instrument panel mounted equipment. Passenger air bags in GM vehicles deploy in different ways depending upon the type of vehicle and the particular instrument panel design. In some vehicles, the passenger air bag deploys through a discrete door located on the top surface of the instrument panel (top-mount air bag systems). In other vehicles, such as the Chevrolet Tahoe, the passenger air bag deploys through a discrete door mounted on the vertical rearward surface of the instrument panel, above the glove box door (mid-mount air bag system). With these types of topmount and mid-mount passenger air bag systems, the top pad of the instrument panel remains in place during deployment. Some GM passenger air bag systems, like the system in the Chevrolet Impala, deploy from beneath the instrument panel top pad. These are considered 3/4-mount air bag systems with a “deployable top pad.” The entire instrument panel top pad is the “deployment door” from under which the inflating air bag emerges. When an air bag deployment is commanded, the forces from the inflating passenger air bag push up on the instrument panel top pad, releasing special fasteners across the rearward edge of the top pad. This allows the top pad to rotate upward so that the passenger air bag may emerge. The top pad rotates upward to open widest at the right hand side, and is usually forced upward into contact with the windshield on the right hand side of the vehicle during a deployment.

Instrument panel top mounted special equipment, such as a radar antenna and control unit or video camera must be positioned to the left of the vehicle center line. This equipment must be mounted as low as possible and securely fastened to the top pad to avoid being dislodged in the event of a crash and possible air bag deployment. In the process of securely fastening special equipment to the top, DO NOT fasten down the top pad itself to any other vehicle component such as the cluster trim plate. As described above, the top pad rotates upward during a deployment. In order to enable the proper deployment of the passenger air bag, specialty equipment installation MUST NOT PREVENT the top pad from rotating upward during deployment. Location and attachment of special equipment should minimize added resistance or interference to upward rotation of the top pad during deployment. Side-Impact Air Bags for crashes to the vehicle sides. The air bag system in your police vehicle includes includes roof rail mounted Head Curtain side air bags.. The vehicle is also equipped with seat back mounted upper body air bags located on the outboard side of the driver and front passenger seat backs. Together the Head Curtain and seat-mounted side air bags are intended to protect the head and upper body in the event of a side crash. Some vehicles may also be equipped with an optional air bag, mounted on the inboard side of the driver seat back. Can Specialty Vehicle Security Barriers be mounted within the side air bag deployment zones? No. The side air bags inflate extremely fast because of the nature of side crashes to the vehicle. Mounting a security barrier behind the front seats with the ends placed within the side air bag deployment zones will result in unintended interaction between the barrier and the inflating side air bags. To reduce the risk of injury to the vehicle occupants, GM recommends that the side air bag zones be kept free of any customer installed equipment. Customer furnished equipment installed to the vehicle roof. Your police vehicle is designed with an interior roof cover system which includes internal components for the interior lamps and wiring. The roof system may also include side air bag components. Inflation devices may be mounted on the vehicle roof side behind the rear doors as well as air bag tethers retained to the windshield pillars. Care must be taken to avoid damage to these components or interference with their operation when installing roof mounted equipment such as emergency lamps and communication antennas. Recommended GM service procedures must be followed to remove and re-install the instrument panel top pad to ensure that the top pad will release properly in the event of a passenger air bag deployment. On the right half of the top pad closest to the passenger air bag module, GM recommends that no equipment be mounted. When mounting equipment on the driver side of the top pad, GM recommends that the total mass of the top pad mounted special equipment not exceed 8 pounds (3.6 kilograms), since some top pads tend to rotate about the left end. Fasteners used to secure special equipment to the instrument panel top pad, the windshield glass, or to the windshield upper frame (header), should be selected to ensure that these devices will remain attached during a vehicle crash and possible air bag deployment.

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

AIR BAGS FAQ | 11 Can the installation of push bumpers on the front end of the vehicle affect the deployment of the air bag?

I've heard that a deployed air bag produces whet appears to be smoke, is the air bag hot?

General Motors is not aware of adverse effects during crash events from the many push bumpers thai have been installed on GM police vehicles. Because there are many styles of push bumpers available with varying crash characteristics, installation of push bumpers may or may not affect deployment timing of the air bags. Push bumpers should be mounted to avoid modifying the vehicle structure and interfering with the front air bag sensors mounted on the upper radiator support cross member

After the bag has deployed in a crash, the air bag itself will not be hot to touch. Some components within the air bag module will be hot for a short time. A small amount of smoke coming from a deployed air bag module is normal and should not be cause for concern.

Two front impact sensors are installed in General Motors vehicles. Do not relocate or disconnect the front sensors. The location and orientation of the front sensors are critical for correct operation of the air bag system. Avoid mounting components on or near the sensors. Push bumper styles with vertical pushing members that are in foreaft alignment with the front air bag sensors are not recommended. When should an air bag inflate? The driver's and right-front passenger's frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system's designed "threshold level." In addition, your vehicle has “dual stage” frontal air bags which tailor the the amount of restraint according to crash severity. For moderate frontal impacts, the air bags inflate at a level less than full deployment. For more severe frontal impacts, "dual stage" frontal air bags deploy at full levels. If the front of your vehicle goes straight into a wall that doesn't move or deform, the threshold level of the reduced deployment is about 12 to 16mph (19 to 15 km/h), and the threshold level for a full deployment is about 18 to 24 mph (29 to 28.5 km/h). The threshold level can vary, however, with specific vehicle design, so that it can be somewhat above or below this range. If your vehicle strikes something that will move or deform such as a parked car, the threshold level will be higher. The driver's and right-front passenger's frontal air bags are not designed to inflate in rollover, side impacts, or rear impacts, because inflation would not help the occupant. Seat mounted side impact air bags are designed to inflate in moderate to severe side crashes. The side impact air bags will inflate if the crash severity is above the designed "threshold level." The threshold level can vary with specific vehicles design. The side impact air bags are not designed to inflate on frontal or near-frontal impacts or rear impacts, because inflation would not help the occupant.

Also, when the nitrogen gas is vented out of the air bag, small particles from inside the bag are also vented into passenger compartment. These airborne particles look like smoke and some particles are deposited as residue on and around the air bag. I've heard that the dusts that are released into the passenger compartment from the air bag are harmful, is this true? For most people, the only effect the dusts will produce is some irritation of the throat and eyes, and that is only if the occupant remains in the vehicle for many minutes after the air bag deployment with no ventilation and windows closed. However, some people with asthma may develop an asthmatic attack from inhaling the dusts. If this happens, they should first treat themselves the same way their doctor has advised them to treat any other asthma attack, and then immediately seek medical treatment. Can the air bag system be re-used? No, The air bags are designed to inflate only once. After inflation some new parts will be required. These will include the air bag module and possibly other parts. (A competent service technician with access to the vehicle's service manual and the required tools should replace the required components after a deployment crash.) If my vehicle has air bags, why should I have to wear my safety belt? Air bags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts not instead of them. Every air bag system ever offered for sale has required the use of safety belts. Even if you're in a vehicle that has air bags, you still have to buckle up to get the most protection. That's true not only in frontal collisions but especially in side and other collisions.

Roof rail mounted head-curtain air bags are designed to inflate in moderate to severe side crashes. In addition, certain vehicles have head-curtain air bags which are also designed to inflate in situations where an impending rollover condition is identified by the vehicle's rollover sensing system and/or frontal or near-frontal impacts if the crash severity is above the designed "threshold level". Safety belt pretensioners at the driver and front passenger seat positions are designed to deploy in frontal, near-frontal, side, and rear crashes that exceed the "threshold level" of crash severity to help reduce slack in the safety belt Safety belt pretensioners will also deploy in impending rollover situations. How long will the air bag remain inflated? It takes approximately 1/20th of a second to fully inflate the frontal air bags. This is faster than the blink of an eye. The air bags begin to deflate immediately, helping to stop the occupants more gradually.  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

12 | AIR

BAGS

Top View of Instrument Panel and APproximate Deployment Area of the Air bag Zone A. B. C. D. E. F. G. H. I. J. K. L. M.

Passenger side instrument panel top surface zone Passenger side air bag module trim panel – rear edge Passenger side door Approximate dimensions of inflated air bag Passenger side air bag deployment zone Passenger centerline Inside rearview mirror Vehicle centerline Driver centerline Driver side air bag deployment zone Front of steering wheel Driver side door Shift selector arc

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

AIR BAGS | 13

Side View of Driver Side Air bag Deployment Zone

A. Top edge of windshield B. Top of instrument panel C. Inflated air bag – steering wheel D. Centerline of steering column at mid-tilt E. Driver air bag deployment zone F. Front of steering wheel

Side View of Passenger Side Air bag Deployment Zone

A. Top edge of windshield B. Inside rearview mirror C. Instrument panel top surface zone D. Passenger side air bag module trim panel – rear edge E. Inflated air bag – horizontal dimension approximate 15.4 in (390 mm) F. Inflated air bag – vertical dimension approximate 9.3 in (490 mm) G. Inflated air bag – instrument panel H. Passenger air bag deployment zone

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information. NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

14 | AIR

BAGS Head Curtain and front Seat-Mounted Side IMpact Air bag Deployment Zones Passenger Side Shown, Driver Side Similar



­ Tahoe/Suburban/Silverado Crew Cab Seat Rows 1 and 2 A.  Top of deployment zone – along head curtain at edge of headliner B.  Back of deployment zone – at rear top corner of rear door pad C.  Rear quarter window D. Bottom outside edge of rear quarter window E. Bottom of air bag deployment zone – parallel to outside bottom edge of rear quarter glass F.  Top edge of rear door pad G.  Top edge of front door pad H.  Dimension at mirror patch from top edge of front door pad I.  Front of deployment zone at front upper corner of front door pad J.  Windshield pillar trim with grab handle K.  Visor L.  Deployment zone - Tahoe seat rows 1 and 2

Tahoe/Suburban 3rd Row Seats M.  Deployment zone - Tahoe 3rd seat N.  Deployment zone - Suburban 3rd seat O. Rear zones at back corner of headliner: 1 Tahoe, 2 Suburban P. Bottom of 3rd seat zone at rear side trim cup holders Q. Top edge of rear quarter trim at window R. Rear of Tahoe S. Rear of Suburban

Tahoe/Suburban/Silverado Crew Cab Seat Air bag T. Center of door trim pull handle U. Top of surface of outboard front seat cushion V. Back edge of center pillar trim­

NOTE: The head curtain air bag inflators are mounted in a different orientation on the Silverado Crew Cab pickup truck roof structure from those in the Tahoe/Suburban.

Head curtain and front Seat-Mounted Side IMpact Air bag Deployment Zones View from Rear Cargo Area

A.  Head curtain air bag deployment zone B.  Underside of headliner C.  Edge of headliner D.  Inner center pillar trim E.  Inner door pad

F.  Seat centerline G. Bottom of door windows H. Front seat headrests I. Seat-mounted side impact air bags deployment zone front seat J. Top surface of outboard front seat cushion

 ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always H use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

Anti-lock braking system FAQ | 15 GM offers Anti-Lock Brake Systems as standard or optional on all North American passenger vehicles and light truck lines. The computerized Anti-Lock Braking System (ABS) is designed to keep the vehicle’s wheels rotating as the brakes are applied to assist the driver in achieving a controlled stop. Sensors monitor how fast the wheels rotate and feed the data continuously to the ABS computer. The vehicle’s brakes slow each wheel as the brake pedal is applied. However, when ABS is activated due to road conditions, the system repeatedly releases and applies pressure to the brakes. The wheels can keep rolling, thus retaining steering ability and enhanced stability while providing a higher braking force on most surfaces than a locked wheel provides. How exactly does ABS work? In cars without ABS, hitting the brakes can cause the wheels to lock, leaving you unable to steer the vehicle until you decrease the pressure so the wheels can roll again. With an ABS, as you apply the brakes, the ABS computer monitors the wheel speed sensor information. If the computer senses that a wheel is approaching lock up, it sends a signal to the hydraulic modulator to reduce, then to reapply, brake pressure several times a second for as long as you maintain firm pressure on the brake pedal. The process is much like the threshold braking technique used with conventional brakes. However, ABS does it much faster and more accurately than any driver can, leaving you free to focus on steering away from obstacles.

Does ABS reduce stopping distances?

Should I drive an ABS equipped vehicle differently than I would drive a vehicle with conventional brakes? Most of the time, under normal driving circumstances, there is no difference, and you should always drive with the same caution and care. It is important to realize that ABS only makes a difference when it is activated—when you have to brake hard—and that would only be when the computer senses that a wheel is approaching lockup. When ABS activates, keep steady pressure on the brake pedal and then let the ABS work for you. Don’t pump the brakes or try to ­find the threshold. Simply hold the brake pedal down and steer if necessary to avoid an obstacle.

Is ABS always active? ABS is always available, but not always activated. ABS is activated only when the brake pedal is applied and the computer detects an impending wheel lock condition.

Can older cars be retrofitted with ABS? No! The brake system is one of the most important features on any passenger vehicle. Several products, which tap into the master cylinder and/or brake system performance, are being sold in the aftermarket. Some of these products imply performance similar to new vehicle anti-lock brake systems. However, contrary to their claims, add-on systems, which deplete fluid from the master cylinder on brake apply may actually increase a vehicle’s stopping distance. This may cause the vehicle to fail to comply with Federal brake standards.

Does ABS always activate at the same speed? No, the system operates when the computer detects wheel lockup, at any speed above 8 mph.

Yes, in braking situations where the wheels on a non-ABS equipped vehicle would lock up, ABS will generally provide shorter controlled stopping distance. The amount of improvement in stopping distance depends on many factors, including the road surface, severity of braking, initial vehicle speed, etc. On some surfaces, such as gravel roads, braking distances can be longer, but you will still have the control benefits of ABS. The important capability of ABS is control. ABS provides improved vehicle steerability and stability when braking.

Will ABS wear out a vehicle’s brakes sooner?

What can affect the ABS advantage?

Do Federal Safety Standards mandate ABS?

It is important that you follow the maintenance schedule recommended in the owner’s manual of the vehicle, tires should be at their proper inflation level, the brake pads should be checked regularly, etc. While driving, you should sit comfortably, so that your hips are back in the seat and your knees are bent, even while braking. Your foot should be positioned so that your heel is on the floor and your toes are secure on the lower half of the pedal. And, though ABS may reduce stopping distance, remember: The faster you go, the longer it takes you to stop. Keeping a safe distance between you and the vehicle in front of you is always necessary, even with ABS.

A properly maintained brake system will be unaffected by ABS operation under typical driving conditions.

Are there different types of ABS? Yes, there are rear wheel anti-lock systems (RWAL) used on some trucks and four-wheel ABS available on cars and trucks.

No. Federal standards establish minimum braking performance requirements that all vehicles must meet, but do not specify how they should be met. It should be noted that even a vehicle with failed ABS meets the Federal safety standard for stopping distances.

Will a tire size change affect ABS? Use of tires other than original equipment may affect ABS performance. Owners should consult and follow the recommendations contained in the vehicle owner’s manual regarding replacement tire size. NOTE: ABS will work with original equipment spare tire or tire

What happens if ABS becomes inactive?

chains. However, performance is reduced.

The ABS electronic control unit has on-board diagnostic capability. If a fault is detected, the vehicle will revert to the base brake system, and the ABS telltale on the dash will be illuminated. Should this happen, the vehicle should be taken to a dealership for repair as soon as possible.

Do insurance companies give a discount for ABS?

How do I use ABS? Depress and hold the pedal. DO NOT PUMP THE BRAKES (that prevents the system from working). Just hold the brake pedal down and let the ABS work for you. You may feel the brake pedal vibrate, or you may notice some noise, but this is normal as the system works for you.

Yes, many insurance companies give discounts that range from 5% to 10%. In the states of New York and Florida all insurance companies are required to give an ABS discount of 5% on certain coverages such as bodily injury, property damage, collision, and personal injury protection. In other states the discount varies from insurance company to insurance company. When buying auto insurance, always ask your insurance agent if his/her company gives a discount for vehicles equipped with antilock brakes.

NOTE: All dimensions are approximate and subject to change.

2014 Chevrolet Municipal Vehicles Technical Manual

16 | Anti-lock

braking system and Stabilitrak

IMPORTANT DRIVING SAFETY TIPS A. A lways maintain a safe

following distance. ABS does not

allow you to stop on a dime. (Generally a 2-second following distance is considered safe in ideal conditions.) Watch the vehicle in front of you pass a fixed marker (such as a sign). Count seconds—one-thousand-one, one-thousand-two-until your front bumper reaches the marker. If you do not count out two seconds, then you are too close to the vehicle in front of you. Also, if the roads are wet or icy, or visibility is poor, you should increase your following distance.

B. A lways drive carefully—

especially on slippery surfaces. ABS cannot create friction between the tires and the road surface, it can only give the driver the maximum advantage of the existing adhesion. If the vehicle is traveling on a surface with no adhesion, the best ABS in the world cannot provide a shorter stopping distance or good steering.

C. It is a good idea to practice an

ABS activated stop and get the feel of the brake pedal. However, please make sure it’s at a safe time with no obstacles in your path. And you only really need to try it once or twice to know what happens.

Electronic Stability Control systems (StabiliTrak) Q. How does StabiliTrak work? StabiliTrak systems help drivers maintain control of their A. StabiliTrak has the ability to apply control forces to vehicles, especially during emergency lane changes or the vehicle independent of the driver. StabiliTrak uses avoidance maneuvers. StabiliTrak uses various sensors, sensors to continuously compare the path indicated by such as steering wheel angle, wheel speed, yaw velocity, the steering wheel position to the vehicle’s actual path. If etc., to detect any difference between the path requested a discrepancy is detected, StabiliTrak selectively controls by the steering wheel position and vehicle’s actual path. vehicle brakes and engine torque to create a yaw moment When appropriate, the system selectively controls brakes, that helps restore the vehicle’s actual path to the path engine power, and even suspension settings to enhance indicated by the steering wheel position. StabiliTrak has control of the vehicle’s direction and help keep it on course. the ability to help correct both understeer (where the Independent studies conducted by the National Highway vehicle is not turning as much as the steering wheel Traffic Safety Administration, the Insurance Institute for position indicates) and oversteer (where the vehicle is Highway Safety, and others have found StabiliTrak to be turning more than the steering wheel position indicates). highly effective in reducing vehicle crashes. General Motors The illustration at right shows how selective braking at a offers StabiliTrak systems on many of its passenger car particular wheel can create a compensating yaw moment and light truck models. to help restore the vehicle’s actual path to the path See your owner's manual for additional information about indicated by the steering wheel position. the operation of StabiliTrak. Q. Will a tire change affect StabiliTrak? Q. How do I use StabiliTrak? A. Use of tires other than original equipment may affect A. S  tabiliTrak operates independently of the driver. You StabiliTrak performance. StabiliTrak is designed to make should continue to drive your StabiliTrak equipped the best use of available traction. The performance vehicle with caution and care. GM’s StabiliTrak system, characteristics of the original equipment tires are part of StabiliTrak, is designed to be as seamless as possible in the overall system effectiveness. When you replace tires operation, to be part of the overall vehicle response and to check the recommendations in your owner's manual. On make a good vehicle better GM vehicles, the original equipment tires have a “TPC” (Tire Performance Criteria) code on the sidewall. Replacing the tires with the same “TPC” code will help assure proper StabiliTrak performance.

2014 Chevrolet Municipal Vehicles Technical Manual

SILVERADO 1500 CREW CAB Pickup work TRUCK 1WT | 1

Updates for 2014

New Features











• Improved chassis and suspension • Extensive usage of high-strength steel throughout the frame and cab structures for capability, quietness, and safety • Exterior redesign with improved aerodynamics for noise isolation and fuel economy • interior redesign with improved comfort, functionality, and durability • EcoTec3 powertrains featuring a standard aluminum engine block, Direct Injection, Active Fuel Management, Continuously Variable Valve Timing, and six-speed automatic transmission • Standard 4.3L V-6 with 285 hp and 305 lb-ft of torque (fuel economy TBD) • Available 5.3L V-8 with 355 hp and 383 lb-ft of torque, capable of up to 23 mpg HWY with a standard 9.5-inch rear axle • 2-years/24,000 miles standard scheduled maintenance including oil change, oil filter replacement, tire rotation, and multi-point vehicle inspection (whichever comes first, see dealer for details) • standard CornerStep rear bumper with box rail grip pockets for easier access to cargo box, also includes standard box rail protectors











•A  vailable under-rail LED cargo box lighting and adjustable all-metal upper tie-downs, each with 250 lbs. load capacity • Available 6'6" bed on Crew Cab models • Available Trailering Package now includes both a 4-pin and 7-pin trailering harness • Crew Cab redesigned with increased rear legroom, foot swing space, and under-seat volume • Shear-style and hydraulic body mounts that isolate up-and-down and side-toside movements to reduce noise, vibration, and harshness, for a quiet, controlled ride • Standard four-wheel disc brakes with DURALIFE rotors • Standard Electric Power Steering for efficient cornering and stability • Improved connectivity with standard USB ports (2), auxiliary jack and SD card slot, and available three-prong 110-volt outlet • New available colors include Brownstone Metallic and Tungsten Metallic

2014 Chevrolet Municipal Vehicles Technical Manual

2 | SILVERADO

1500 CREW CAB Pickup work TRUCK 1WT

NOTE: This vehicle is NOT designed nor intended for use IN HIGH SPEED EMERGENCY VEHICLE OPERATIONS

Model availability CC15543

2-wheel drive 1/2 ton fleetside short box crew cab pickup

Ck15543

4-wheel drive 1/2 ton fleetside short box crew cab pickup

CC15743

2-wheel drive 1/2 ton fleetside standard box crew cab pickup

Ck15743

4-wheel drive 1/2 ton fleetside standard box crew cab pickup

Standard equipment summary Warranty 3 years / 36,000 miles bumper-to-bumper (whichever comes first, see dealer for details) and '5 years / 100,000 miles limited powertrain (whichever comes first, see dealer for details)' both above maintenance warrant MAINTENANCE 2 years / 24,000-miles scheduled vehicle maintenance including oil change, oil filter replacement, tire rotation, and multi-point vehicle inspection (whichever comes first, see dealer for details)

interior features Air bags1 Dual-stage frontal and side-impact, driver and front passenger and head-curtain and seat-mounted side-impact, front and rear outboard seating positions with Passenger Sensing System Air conditioning Single-zone Assist handle Front passenger on A-pillar Audio system 4.2” Color Display, AM/FM stereo with USB ports (2), auxiliary jack and SD card slot Coat hooks Rear driver and passenger side Console Floor (not available) Cruise control Electronic with set and resume speed, steering wheel-mounted Cup holders Front, and rear Door locks Power Driver information center Odometer, trip odometer and message center (monitors numerous systems depending on vehicle equipment level including low fuel, turn signal on, transmission temperature and oil change notification) (Driver Information Center controls are operated through the trip button unless uk3 steering wheel mounted audio controls is ordered) Floor covering Graphite-colored rubberized-vinyl, no floor mats included' Instrumentation 6-gauge cluster featuring speedometer, fuel level, engine temperature, tachometer, voltage and oil pressure lighting Interior with dome and reading lights, illuminates entry feature and backlit instrument panel switches Mirror Inside rearview manual day/night Power outlets 2 auxiliary instrument panel-mounted with covers, 12-volt remote keyless entry 2 transmitters, panic button and content theft alarm (Remote keyless entry is part of PCR Package. Package includes power mirrors.) Restraint system Safety belts, driver and front passenger with pretensioners, dual stage driver and passenger frontal air bags1, passenger sensing system and frontal air bag1 ON/OFF indicator, rollover sensor, dual head curtain air bags1 for first and second row outboard occupants and front seat back mounted thorax-pelvic air bags1 Seat, front 40/20/40 vinyl split-bench, 3-passenger, driver and front passenger manual reclining with outboard head restraints and center folddown armrest with storage Seat, rear 60/40 vinyl bench (folds up), 3-passenger (includes child seat top tether anchor) Steering wheel Includes theft deterrent locking feature Steering column Tilt-wheel, adjustable with brake/transmission shift interlock Visors Driver and front passenger, sliding with clip and illuminated passenger vanity mirror

1. H  ead curtain side air bags are designed to help reduce the risk of head and neck injuries to front and rear seat occupants on the near side of certain side-impact collisions. Always use safety belts and the correct child restraints for your child’s age and size, even in vehicles equipped with air bags. Children are safer when properly secured in a rear seat. See your vehicle Owner’s Manual and child safety seat instructions for more information.

2014 Chevrolet Municipal Vehicles Technical Manual

SILVERADO 1500 CREW CAB Pickup work TRUCK 1WT | 3 Warning tones Headlamp on, key-in-ignition, driver and passenger buckle up reminder and turn signal on

exterior features Air dam Bumpers Front Bumpers Rear Corner Step Daytime Running Lamps Door handles

Black Black Black Rear bumper Automatic exterior lamp control Black

Glass

Solar-Ray light-tinted, all windows

Grille Headlamps Lamps Mirrors

Black surround Halogen reflector Cargo area, cab mounted with separate switch on center switch bank Outside manual, Black

Recovery hooks

Front black (Standard on 4WD available on 2WD)

WINDSHIELD Wipers

Front intermittent wet-arm with pulse washers

chassis features Alternator 150-amps Battery Heavy-duty 600 CCA, maintenance-free with rundown protection and retained accessory power Brakes 4-wheel disc with DURALIFE rotors, 4-wheel antilock Cooling External engine oil cooler, heavy-duty Engine 4.3L V6 EcoTec3 with Active Fuel Management, Direct Injection and Variable Valve timing, includes aluminum block construction with FlexFuel capability, capble of running on unleaded or up to 85% ethanol Exhaust Aluminized stainless-steel muffler and tailpipe Frame Fully-boxed, hydroformed front section Fuel Tank 26 gallon (98 liter) Rear axle 3.23 ratio with 2WD, 3.42 with 4WD (see engine/axle/transmission chart page 5) StabiliTrak Stability control system with Proactive Roll Avoidance and traction control includes electronic trailer sway control and hill start assist Steering Electric Power Steering (EPS) assist, rack-and-pinion Suspension, Front Independent, coil over shock, includes 35mm twin tube shock absorbers and 36mm front stabilizer bar Suspension, Rear 2-Stage multi-leaf springs, semi-elliptic Tailgate Locking, utilizes same key as ignition and door Tire pressure monitor Tire Pressure Monitor System (does not apply to spare tire) Tire, Spare carrier Outside, winch-type mounted under frame at rear Tires P255/70R17 all-season, blackwall Tire carrier lock Keyed cylinder lock that utilizes same key as ignition and door Transfer case Floor-mounted shifter (requires 4-wheel drive model) Transmission 6-speed automatic electronically controlled with overdrive and tow/haul mode. Includes Cruise Grade Braking and Powertrain Grade Braking Wheels 17" x 7.5" (43.2 cm x 19.1 cm) steel 6 lug painted, includes painted center caps (spare wheel will not cosmetically match the other 4)

2014 Chevrolet Municipal Vehicles Technical Manual

4 | SILVERADO

1500 CREW CAB Pickup work TRUCK 1WT

SEATS AND INTERIOR TRIM INTERIOR SEAT TYPE SEAT OPTION SEAT TRIM JetBlack/ Dark Ash

S tandard

Front: 40/20/40 split-bench with fold-down armrest and fixed driver lumbar

AE7

Vinyl

H2Q

Optional

Front: 40/20/40 split-bench with fold-down armrest and driver manual adjustable lumbar

AE7

Cloth

HR2

Optional

Front 40/20/40 reclining split-bench with fold-down armrest and lockable storage compartment and manually adjustable driver lumbar

AZ3

Cloth

H2S





AVAILABLE EXTERIOR COLORS

­­

G56

GAN

GAZ

GBA

GCE

GCN

GTS

GWX

GXG

Blue Granite Metallic

Silver Ice Metallic

Summit White

Black

Deep Ruby Metallic

Victory Red

Blue Topaz Metallic

Brownstone Metallic (New)

Tungsten Metallic (New)



SEo Paint Available WA#

COLOR DESCRIPTION

CODE

9015

Woodland Green

9V5

9403

Doeskin Tan

9V9

253A

Wheatland Yellow

9W3

9417

Tangier Orange

9W4

7159

Blue Metallic

TBD

334D

Dark Toreador red

TBD

136X

Unripened Green Metallic

TBD

9792

Indigo Blue

TBD

228A

Light Autumnwood Metallic

TBD

382E

Pewter none



TBD

Actual Color May VAry

2014 Chevrolet Municipal Vehicles Technical Manual

Actual colors may vary

SILVERADO 1500 CREW CAB Pickup work TRUCK 1WT | 5 POWERTRAIN S = Standard

A= Available TRANS AXLE ENGINE

MYC 6-speed auto. GU4 Heavy Duty 3.08

CC15543

(std) LV3 4.3L V6 EcoTec3 AFM DI VVT Flex Fuel aluminum block (opt) L83 5.3L V8 EcoTec3 AFM DI VVT Flex Fuel aluminum block CC15743 (std) LV3 4.3L V6 EcoTec3 AFM DI VVT Flex Fuel aluminum block (opt) L83 5.3L V8 EcoTec3 AFM DI VVT Flex Fuel aluminum block CK15543 (std) LV3 4.3L V6 EcoTec3 AFM DI VVT Flex Fuel aluminum block (opt) L83 5.3L V8 EcoTec3 AFM DI VVT Flex Fuel aluminum block CK15743 (std) LV3 4.3L V6 EcoTec3 AFM DI VVT Flex Fuel aluminum block (opt) L83 5.3L V8 EcoTec3 AFM DI VVT Flex Fuel aluminum block

GVWR lbs (kg)

GU5

C5H GU6 6900

C5W 7000

C5Y 7100

C5Z 7200

3.23

3.42 (3130)

(3175)

(3221)

(3266)

S



S



S







S

S



A



A



A1

S



S





S







S

S



A





A



A1

S





S







S



S

S



A









A2

S





S







S



S

S



A









A2

1 - Requires (NHT) Max Tailering Package. 2 - Required with (NHT) Max Trailering Package.

EMISSIONS FE9

MUST BE SPECIFIED

F ederal emissions. Use for ordering vehicles that will be registered in all states except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State

YF5 California emissions. Use for ordering vehicles that will be registered in California. NE1 CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA emissions. Use for ordering vehicles that will be registered in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington State NB8

Required when option code FE9 “Federal emissions” is ordered for delivery to a dealer located in California, Connecticut, Massachusetts, Maryland, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island and Washington State for a purchaser who will be registering the vehicle outside California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington State.

NC7

Required when option code YF5 “CALIFORNIA EMISSIONS” or option code NE1 "CT/ME/MD/MA/NJ/NM/NY/OR/PA/RI/VT/WA EMISSIONS" is ordered for delivery to a dealer located in any state except California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington for a purchaser who will be registering the vehicle in one of these states or sold as permitted below under “EPA Policy on the Sale of California Emission Vehicles”

NB9

Required when option code YF5 is ordered for delivery to a dealer located in Connecticut, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington. Required when option code NE1 is ordered for delivery to a dealer located in California.

Automatic Transmission

(LV3) 4.3L V6 EcoTec3 AFM DI

WITH BALL HITCH

L83 5.3L V8 EcoTec3 AFM DI

Model VVT FlexFuel aluminum block VVT FlexFuel aluminum block

Axle Ratio Max Trailering AXLE RATIO MAX TRAILERING AXLE RATIO MAX TRAILERING

CC15543



3.23

5900/2676

3.08

6800/3084

3.42

9800/4445

CC15743

3.23

5800/2631

3.08

6700/3039

3.42

9700/4400

CK15543

3.42

6700/3039

3.08

6600/2994

3.42

9600/4355

CK15743

3.42

6600/2994

3.08

6500/2948

3.42

9500/4309

Silverado 1500 models are limited to 5000 lb. trailer rating unless equipped with (Z85) Handling/Trailering Suspension Package, (Z60) High-Performance Suspension Package or (Z71) Off-Road Suspension Package.

Addition of trailer tongue weight cannot cause vehicle weights to exceed Rear Gross Axle Weight Rating (RGVWR) of Gross Vehicle Weight Rating (GVWR).

2014 Chevrolet Municipal Vehicles Technical Manual

6 | SILVERADO

1500 CREW CAB Pickup work TRUCK 1WT

BVQ Assist steps – Chromed tubular, 6” oval factory installed, Not available with any LPO assist steps (RVQ), (RVS), (VXH) or (VXJ). VBN Bed rug – Bed cover, foam backed gray colored carpet like material that covers the entire bed, not available with VBR Rubber bed mat V46 Bumper – Front chrome VJH Bumper – Rear chrome CTD Cargo tie downs (4) – Movable upper IO4 Chevrolet MyLink audio system – 4.2” diagonal color screen with AM/FM stereo, USB ports (2), auxiliary jack, SD card slot, Bluetooth streaming audio for music and most phones, hands-free smartphone integration, Pandora Internet radio and voice-activated technology for radio and phone, See “gmtotalconnect.com” for phone compatibility info. PCX Chrome Bumper Package – Includes (VJH) rear chrome bumper with (BWN) CornerSteps and (V46) chrome front bumper KNP Cooling – Auxiliary external transmission oil cooler, Included and only available with (L83) 5.3L V8 EcoTec3 engine. C49 Defogger – Rear-window electric G80 Differential – Heavy-duty locking rear. NB8 Emissions override – California (allows a dealer in states that require California emissions - California, Connecticut, Delaware, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island or Washington - to order Federal emissions for a vehicle that will be registered in a state that has Federal emission requirements). Do not use for vehicles that will be registered in California, Connecticut, Delaware, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island or Washington., Requires (FE9) Federal emissions requirements. Not available in Maine or Vermont. NC7 Emissions override – Federal (for vehicles ordered by dealers in Federal emission states with (YF5) or (NE1) emissions - Not required for vehicles being shipped to California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington), Requires (YF5) California state emissions requirements or (NE1) Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont or Washington state emissions requirements. NB9 Emissions override – State-specific (for dealers ordering vehicles in (YF5) or (NE1) emission states - California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington), Allows a California dealer (YF5 emissions) to order (NE1) emissions with (NB9) emissions override code for registration in (NE1) states; or, a Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington dealer (NE1 emissions) to order (YF5) emissions with (NB9) emissions override code for registration in California. YF5 Emissions – California state requirements NE1 Emissions – Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont and Washington state requirements FE9 Emissions – Federal requirements K05 Engine block heater L83 Engine – 5.3L V8 EcoTec3 with Active Fuel Management, Direct Injection and Continuously Variable Valve Timing, includes aluminum block construction with Flex Fuel capability, capable of running on unleaded or up to 85% ethanol B30 Floor covering – Color-keyed carpeting with rubberized vinyl floor mats (includes second row floor mats) AKO Glass – deep-tinted C5H GVWR, 6900 lbs. (3130 kg) – Requires 2WD models and (LV3) 4.3L V6 EcoTec3 engine. C5W GVWR, 7000 lbs. (3175 kg) – Requires 2WD models and (L83) 5.3L V8 EcoTec3 engine. Not available with (NHT) Max Trailering Package. C5Y GVWR, 7100 lbs. (3221 kg) – Requires 4WD models and (LV3) 4.3L V6 EcoTec3 engine. C5Z GVWR, 7200 lbs. (3266 kg) – Requires 4WD models and (L83) 5.3L V8 EcoTec3 engine. Not available with (NHT) Max Trailering Package. UF2 LED Lighting – Cargo box VK3 License plate kit – Front (will be shipped to orders with ship-to states that require front license plate) VXJ LPO, Assist steps – Chromed tubular, 4” round Dealer installed, Not available with (RVS) 4” round Black tubular assist step, LPO, (RVQ) 6” oval Black tubular assist step, LPO, (VXH) 6” oval chrome tubular assist step, LPO or (BVQ) 6” chrome tubular assist step. VXH LPO, Assist steps – Chromed tubular, 6” oval Dealer installed, Not available with (RVS) 4” round Black tubular assist step, LPO, (RVQ) 6” oval Black tubular assist step, LPO, (VXJ) 4” round chrome tubular assist step, LPO or (BVQ) 6” chrome tubular assist step. VZX LPO, Bed liner – Dealer installed, Not available with (VUK) tailgate liner, LPO. RXQ LPO, Bed net – Dealer installed RVS LPO, Black tubular assist steps – 4” round, Dealer installed, Not available with (RVQ) 6” oval Black tubular assist step, LPO, (VXJ) 4” round chrome tubular assist step, LPO, (VXH) 6” oval chrome tubular assist step, LPO or (BVQ) 6” chrome tubular assist step. 8. Visit OnStar.com for coverage map, system limitations and details. 10. Go to gm.com/bluetooth to find out which Bluetooth phones are compatible with the vehicle.

2014 Chevrolet Municipal Vehicles Technical Manual

SILVERADO 1500 CREW CAB Pickup work TRUCK 1WT | 7 RVQ LPO, Black tubular assist steps – 6” oval, Dealer installed, Not available with (RVS) 4” round Black tubular assist step, LPO, (VXJ) 4” round chrome tubular assist step, LPO, (VXH) 6” oval chrome tubular assist step, LPO or (BVQ) 6” chrome tubular assist step. RWS LPO, Carpeted floor mats – Front and rear (dealer-installed) VQL LPO, Chrome fuel door – Dealer installed SDA LPO, Chrome recovery hooks – Dealer installed, Requires (V76) Black recovery hooks. SB1 LPO, Flat Splash Guards – Black, Dealer installed, Not available with (VQK) Black molded splash guards, LPO. VQK LPO, Front and Rear Molded Splash GuarDS – Black, Dealer installed, Not available with (SB1) flat Black splash guards, LPO. RW6 LPO, Metal bed storage box – Dealer installed, Not available with (5JY) soft folding tonneau cover, LPO or (VPB) vinyl tonneau cover with integrated support bows, LPO. VQZ LPO, Polished exhaust tip – Dealer installed VBJ LPO, Rear underseat storage – Composite storage bin, Dealer installed VBR LPO, Rubber bed mat – Dealer installed, Not available with (VZX) bed liner, LPO. 5JY LPO, Soft folding tonneau cover – Dealer installed, Requires (UF2) LED Lighting, cargo box. Not available with (VPB) vinyl tonneau cover with integrated support bows, LPO or (RW6) metal bed storage box, LPO. VUK LPO, Tailgate liner – Dealer installed, Not available with (VZX) bed liner, LPO. VQT LPO, Tonneau cover, Hard tri-folding with vinyl cover – Dealer installed, Not available with (VPB) soft tonneau cover, LPO, (5JY) soft-folding tonneau cover, LPO or (RW6) metal bed storage box, LPO. VPB LPO, Vinyl tonneau cover with integrated support bows – Dealer installed, Requires (UF2) LED Lighting, cargo box. Not available with (5JY) soft folding tonneau cover, LPO or (RW6) metal bed storage box, LPO. SFE LPO, Wheel locks – Set of 4 (dealer-installed) DL8 Mirrors – Outside heated power-adjustable, black (includes driver’s side spotter mirror), Included and only available with (PCR) WT Convenience Package. DF2 Mirrors – Outside high-visibility vertical camper-style, Black with manual folding and extension and lower convex spotter glass. UE1 OnStar – 6 months of Directions and Connections plan, Visit onstar.com for details and system limitations. VAV LPO, All-weather floor mats – Front and rear (dealer-installed) KI4 Power outlet – 110-volt AC, Included and only available with (PCR) WT Convenience Package. GU4 Rear axle, 3.08 ratio – Requires (L83) 5.3L V8 EcoTec3 engine. GU6 Rear axle, 3.42 ratio – Standard on 4WD (LV3) 4.3lL V6 EcoTec3 engine and (L86). Available with (L83) 5.3L V8 EcoTec3 engine. AQQ Remote Keyless Entry – With 2 transmitters, Included and only available with (PCR) WT Convenience Package. AZ3 Seats – front 40/20/40 split-bench, 3-passenger, cloth. Includes driver and front passenger recline with outboard head restraints and center fold-down armrest with storage. Also includes manually adjustable driver lumbar, lockable storage compartment in seat cushion, and storage pockets. U2M SiriusXM Satellite Radio and HD Radio – Requires (IO4) 4.2” color radio with Chevrolet MyLink and (UE1) OnStar. If you subscribe after your trial period, subscriptions are continuous until you call SiriusXM to cancel. See SiriusXM Customer Agreement for complete terms at www.siriusxm.com. Other fees and taxes will apply. All fees and programming subject to change. 2 - If you subscribe after your trial period, subscriptions are continuous until you call SiriusXM to cancel. See SiriusXM Customer Agreement for complete terms at www.siriusxm.com. Other fees and taxes will apply. All fees and programming subject to change. RHM Tire – Spare LT265/70R17 all-terrain, blackwall, Included and only available with (RC5) LT265/70R17C blackwall tires. ZBZ Tire – Spare P255/70R17 all-season, blackwall, Included and only available with (RBZ) P255/70R17 all-season, blackwall tires. RC4 Tire – Spare P265/70R17 all-season, blackwall, Included and only available with (RC3) P265/70R17 all-terrain blackwall tires. RC5 Tires – LT265/70R17C, blackwall RC3 Tires – P265/70R17 all-terrain, blackwall JL1 Trailer brake controller – Integrated. PCR WT Convenience Package – Includes (AQQ) Remote Keyless Entry and (DL8) outside heated, power mirrors.

2014 Chevrolet Municipal Vehicles Technical Manual

8 | SILVERADO GCWR

1500 CREW CAB Pickup work TRUCK 1WT

Engine/Rear Axle Ratio Combination with Auto Transmission



(GCWR) Gross Combination weight ratings lbs. (kg)

ENGINE 11,000/4,990 (LV3) Vortec 4.3L V6 EcoTec3 AFM 3.23 (L83) Vortec 5.3L V8 SFI FlexFuel



12,000/5,443 14,000/6,350 3.42 3.08 3.42*

15,000/6,804 3.42

16,700/7,575 3.73**

* - Requires RPO (NHT) Max Trailering Package. ** - With Regular cab standard box model.

CREW CAB SPECIFICATIONS CC15543 CK15543 CC15743 2WD Short Box 4WD Short Box 2WD STD Box Crew Cab Crew Cab Crew Cab Specifications Front shock absorber diameter, in./mm 1.81/46 1.81/46 1.81/46 Front stabilizer bar diameter, in./mm 1.35/34 1.35/34 1.35/34 Rear shock absorber diameter, in./mm 1.38/35 1.38/35 1.38/35 Turning diameter, curb-to-curb, ft./m 47.2/14.4 47.2/14.4 48.6/14.8 Capacities Front axle1, lbs./kg 3,650/1,656 3,950/1,792 3,650/1,656 Front spring capacity, lbs./kg 3,650/1,656 3,950/1,792 3,650/1,656 Rear axle2, lbs./kg 3,950/1,792 3,950/1,792 3,950/1,792 Rear spring capacity, lbs./kg 3,950/1,792 3,950/1,792 3,950/1,792 Curb weight, lbs./kg 4,942/2,242 5,139/2,331 5,000/2,268 Cargo volume, cargo box, cu. ft./liters 53.4/1,512.3 53.4/1,512.3 61.0/1,727.5 Payload3, lbs./kg 2,007/910 1,957/888 1947/883 Gross Vehicle Weight Rating/GVWR , lbs./kg 6,900/3,130 7,100/3,221 6,900/3,130 Front Gross Axle Weight Rating/GAWR ,lbs./kg 3,650/1,656 3,950/1,792 3,650/1,656 Rear Gross Axle Weight Rating/GAWR ,lbs./kg 3,950/1,792 3,950/1,792 3,950/1,792 Fuel capacity, approximate, gallon/liters 26/98 26/98 26/98 Seating capacity 6 6 6 1. Mass values are calculated assuming nominal equipment. Actual values may vary due to equipment loading. 2. Mass values are calculated assuming nominal equipment. Actual values may vary due to equipment loading. 3. Maximum payload capacity includes weight of driver, passengers, optional equipment and cargo.

CK15743 4WD STD Box Crew Cab 1.81/46 1.35/34 1.38/35 48.6/14.8 3,950/1,792 3,950/1,792 3,950/1,792 3,950/1,792 5,197/2,357 61.0/1,727.5 1,883/854 7,100/3,221 3,950/1,792 3,950/1,792 26/98 6

DIMENSIONS (in./mm) CC15543 CK15543 CC15743 CK15743 2WD Short Box 4WD Short Box 2WD STD Box 4WD STD Box Crew Cab Crew Cab Crew Cab Crew Cab LOCATION Wheelbase 143.5/3,645 143.5/3,645 153.0/3,886 153.0/3,886 Overall length 230.0/5,843 230.0/5,843 239.6/6,085 239.6/6,085 Body width 80.0/2,032 80.0/2,032 80.0/2,032 80.0/2,032 Overall height 74.2/1,884 74.0/1,879 73.7/1,873 73.8/1,875 Head room, front 42.8/1,087 42.8/1,087 42.8/1,087 42.8/1,087 Head room, rear 40.5/1,029 40.5/1,029 40.5/1,029 40.5/1,029 Shoulder room, front 66.0/1,677 66.0/1,677 66.0/1,677 66.0/1,677 Shoulder room, rear 65.7/1,670 65.7/1,670 65.7/1,670 65.7/1,670 Hip room, front 60.7/1,543 60.7/1,543 60.7/1,543 60.7/1,543 Hip room, rear 60.3/1,531 60.3/1,531 60.3/1,531 60.3/1,531 Leg room, front 45.3/1,150 45.3/1,150 45.3/1,150 45.3/1,150 Leg room, rear 40.9/1,040 40.9/1,040 40.9/1,040 40.9/1,040 Cab to axle 32.0/812 32.0/812 41.5/1,053 41.5/1,053 Inside length, at floor 69.3/1,761 69.3/1,761 78.9/2,003 78.9/2,003 Inside height 21.1/536 21.1/536 21.1/536 21.1/536 Front bumper to back of cab 150.9/3,833 150.9/3,833 150.9/3,833 150.9/3,833 Inside width, between wheel housing, Fleetside 51.0/1,296 51.0/1,296 51.0/1,296 51.0/1,296 Ground clearance 8.7/222 8.9/226 8.5/216 8.93/227 NOTE: Published dimensions indicated are without optional equipment or accessories. Additional accessories or equipment ordered at the customer’s request can result in a minor change in these dimensions.



2014 Chevrolet Municipal Vehicles Technical Manual

Anti-lock braking system FAQ | 9 GM offers Anti-Lock Brake Systems as standard or optional on all North American passenger vehicles and light truck lines. The computerized Anti-Lock Braking System (ABS) is designed to keep the vehicle’s wheels rotating as the brakes are applied to assist the driver in achieving a controlled stop. Sensors monitor how fast the wheels rotate and feed the data continuously to the ABS computer. The vehicle’s brakes slow each wheel as the brake pedal is applied. However, when ABS is activated due to road conditions, the system repeatedly releases and applies pressure to the brakes. The wheels can keep rolling, thus retaining steering ability and enhanced stability while providing a higher braking force on most surfaces than a locked wheel provides. How exactly does ABS work? In cars without ABS, hitting the brakes can cause the wheels to lock, leaving you unable to steer the vehicle until you decrease the pressure so the wheels can roll again. With an ABS, as you apply the brakes, the ABS computer monitors the wheel speed sensor information. If the computer senses that a wheel is approaching lock up, it sends a signal to the hydraulic modulator to reduce, then to reapply, brake pressure several times a second for as long as you maintain firm pressure on the brake pedal. The process is much like the threshold braking technique used with conventional brakes. However, ABS does it much faster and more accurately than any driver can, leaving you free to focus on steering away from obstacles.

Does ABS reduce stopping distances?

Should I drive an ABS equipped vehicle differently than I would drive a vehicle with conventional brakes? Most of the time, under normal driving circumstances, there is no difference, and you should always drive with the same caution and care. It is important to realize that ABS only makes a difference when it is activated—when you have to brake hard—and that would only be when the computer senses that a wheel is approaching lockup. When ABS activates, keep steady pressure on the brake pedal and then let the ABS work for you. Don’t pump the brakes or try to ­find the threshold. Simply hold the brake pedal down and steer if necessary to avoid an obstacle.

Is ABS always active? ABS is always available, but not always activated. ABS is activated only when the brake pedal is applied and the computer detects an impending wheel lock condition.

Can older cars be retrofitted with ABS? No! The brake system is one of the most important features on any passenger vehicle. Several products, which tap into the master cylinder and/or brake system performance, are being sold in the aftermarket. Some of these products imply performance similar to new vehicle anti-lock brake systems. However, contrary to their claims, add-on systems, which deplete fluid from the master cylinder on brake apply may actually increase a vehicle’s stopping distance. This may cause the vehicle to fail to comply with Federal brake standards.

Does ABS always activate at the same speed? No, the system operates when the computer detects wheel lockup, at any speed above 8 mph.

Yes, in braking situations where the wheels on a non-ABS equipped vehicle would lock up, ABS will generally provide shorter controlled stopping distance. The amount of improvement in stopping distance depends on many factors, including the road surface, severity of braking, initial vehicle speed, etc. On some surfaces, such as gravel roads, braking distances can be longer, but you will still have the control benefits of ABS. The important capability of ABS is control. ABS provides improved vehicle steerability and stability when braking.

Will ABS wear out a vehicle’s brakes sooner?

What can affect the ABS advantage?

Do Federal Safety Standards mandate ABS?

It is important that you follow the maintenance schedule recommended in the owner’s manual of the vehicle, tires should be at their proper inflation level, the brake pads should be checked regularly, etc. While driving, you should sit comfortably, so that your hips are back in the seat and your knees are bent, even while braking. Your foot should be positioned so that your heel is on the floor and your toes are secure on the lower half of the pedal. And, though ABS may reduce stopping distance, remember: The faster you go, the longer it takes you to stop. Keeping a safe distance between you and the vehicle in front of you is always necessary, even with ABS.

A properly maintained brake system will be unaffected by ABS operation under typical driving conditions.

Are there different types of ABS? Yes, there are rear wheel anti-lock systems (RWAL) used on some trucks and four-wheel ABS available on cars and trucks.

No. Federal standards establish minimum braking performance requirements that all vehicles must meet, but do not specify how they should be met. It should be noted that even a vehicle with failed ABS meets the Federal safety standard for stopping distances.

Will a tire size change affect ABS? Use of tires other than original equipment may affect ABS performance. Owners should consult and follow the recommendations contained in the vehicle owner’s manual regarding replacement tire size. NOTE: ABS will work with original equipment spare tire or tire

What happens if ABS becomes inactive?

chains. However, performance is reduced.

The ABS electronic control unit has on-board diagnostic capability. If a fault is detected, the vehicle will revert to the base brake system, and the ABS telltale on the dash will be illuminated. Should this happen, the vehicle should be taken to a dealership for repair as soon as possible.

Do insurance companies give a discount for ABS?

How do I use ABS? Depress and hold the pedal. DO NOT PUMP THE BRAKES (that prevents the system from working). Just hold the brake pedal down and let the ABS work for you. You may feel the brake pedal vibrate, or you may notice some noise, but this is normal as the system works for you.

Yes, many insurance companies give discounts that range from 5% to 10%. In the states of New York and Florida all insurance companies are required to give an ABS discount of 5% on certain coverages such as bodily injury, property damage, collision, and personal injury protection. In other states the discount varies from insurance company to insurance company. When buying auto insurance, always ask your insurance agent if his/her company gives a discount for vehicles equipped with antilock brakes.

10 | Anti-lock

braking system and Stabilitrak

IMPORTANT DRIVING SAFETY TIPS A. A lways maintain a safe

following distance. ABS does not

allow you to stop on a dime. (Generally a 2-second following distance is considered safe in ideal conditions.) Watch the vehicle in front of you pass a fixed marker (such as a sign). Count seconds—one-thousand-one, one-thousand-two-until your front bumper reaches the marker. If you do not count out two seconds, then you are too close to the vehicle in front of you. Also, if the roads are wet or icy, or visibility is poor, you should increase your following distance.

B. A lways drive carefully—

especially on slippery surfaces. ABS cannot create friction between the tires and the road surface, it can only give the driver the maximum advantage of the existing adhesion. If the vehicle is traveling on a surface with no adhesion, the best ABS in the world cannot provide a shorter stopping distance or good steering.

C. It is a good idea to practice an

ABS activated stop and get the feel of the brake pedal. However, please make sure it’s at a safe time with no obstacles in your path. And you only really need to try it once or twice to know what happens.

Electronic Stability Control systems (StabiliTrak) Q. How does StabiliTrak work? StabiliTrak systems help drivers maintain control of their A. StabiliTrak has the ability to apply control forces to vehicles, especially during emergency lane changes or the vehicle independent of the driver. StabiliTrak uses avoidance maneuvers. StabiliTrak uses various sensors, sensors to continuously compare the path indicated by such as steering wheel angle, wheel speed, yaw velocity, the steering wheel position to the vehicle’s actual path. If etc., to detect any difference between the path requested a discrepancy is detected, StabiliTrak selectively controls by the steering wheel position and vehicle’s actual path. vehicle brakes and engine torque to create a yaw moment When appropriate, the system selectively controls brakes, that helps restore the vehicle’s actual path to the path engine power, and even suspension settings to enhance indicated by the steering wheel position. StabiliTrak has control of the vehicle’s direction and help keep it on course. the ability to help correct both understeer (where the Independent studies conducted by the National Highway vehicle is not turning as much as the steering wheel Traffic Safety Administration, the Insurance Institute for position indicates) and oversteer (where the vehicle is Highway Safety, and others have found StabiliTrak to be turning more than the steering wheel position indicates). highly effective in reducing vehicle crashes. General Motors The illustration at right shows how selective braking at a offers StabiliTrak systems on many of its passenger car particular wheel can create a compensating yaw moment and light truck models. to help restore the vehicle’s actual path to the path See your owner's manual for additional information about indicated by the steering wheel position. the operation of StabiliTrak. Q. Will a tire change affect StabiliTrak? Q. How do I use StabiliTrak? A. Use of tires other than original equipment may affect A. S  tabiliTrak operates independently of the driver. You StabiliTrak performance. StabiliTrak is designed to make should continue to drive your StabiliTrak equipped the best use of available traction. The performance vehicle with caution and care. GM’s StabiliTrak system, characteristics of the original equipment tires are part of StabiliTrak, is designed to be as seamless as possible in the overall system effectiveness. When you replace tires operation, to be part of the overall vehicle response and to check the recommendations in your owner's manual. On make a good vehicle better GM vehicles, the original equipment tires have a “TPC” (Tire Performance Criteria) code on the sidewall. Replacing the tires with the same “TPC” code will help assure proper StabiliTrak performance.

2014 Chevrolet Municipal Vehicles Technical Manual

GM Fleet and Commercial Specialty Vehicles • 100 Renaissance Center, 20th Floor • Detroit, MI 48265-1000

2014 CHEVROLET MUNICIPAL VEHICLES TECHNICAL MANUAL

For Information 1-800-FLEET-OP (353-3867) www.gmfleet.com

2014 CHEVROLET MUNICIPAL VEHICLES TECHNICAL MANUAL

Caprice 9C1

I m pa l a 9 C 1

I m pa l a 9 C 3

Tahoe PPV

Tahoe Special Service

E x p r e ss V a n

Suburban

S i lv e r a d o