3D directional coupler for impulse UWB Julien Le Kernec, Martin Klepal, Vratislav Sokol
To cite this version: Julien Le Kernec, Martin Klepal, Vratislav Sokol. 3D directional coupler for impulse UWB. 2011.
HAL Id: hal-00592537 http://hal.upmc.fr/hal-00592537 Submitted on 12 May 2011
HAL is a multi-disciplinary open access archive for the deposit and dissemination of scientific research documents, whether they are published or not. The documents may come from teaching and research institutions in France or abroad, or from public or private research centers.
L’archive ouverte pluridisciplinaire HAL, est destin´ee au d´epˆot et `a la diffusion de documents scientifiques de niveau recherche, publi´es ou non, ´emanant des ´etablissements d’enseignement et de recherche fran¸cais ou ´etrangers, des laboratoires publics ou priv´es.
3D Directional Coupler for Impulse UWB Julien Le Kernec*# — Martin Klepal** — Vratislave Sokol***,… * ONERA, the French Aerospace Lab, Electromagnetic and Radar Department, Chemin de la Hunière, 91120 Palaiseau, France #LIP6-SOC-SYEL,
C2I 2010
UPMC - LIP6 - CNRS UMR 7606 - B.C. 167 – 4 Place Jussieu 75252 PARIS CEDEX 05 – France
[email protected] ** Adaptive Wirelesse Systems, Cork Institute of Technology, Rossa avenue, Cork, Co. Cork, Ireland *** CST Microwave, Branch Office Prague, Vaclava Rady 1470/5, 15600 Prague 5, Czech Republic
Introduction The AWS Group was developing a UWB radar and UWB transceiver for indoor people location and tracking. A radar concept has been developed. The radar is composed of a pulse generator, a channel model, a low-noise amplifier, a matched filter, two pulse shapers, a flip-flop circuit and an integrator. This poster will focus on the design of the directional coupler. This component will provide a separation between the pulse generator and the Low Noise Amplifier. This enables the radar system to connect on the same antenna.
Design Specifications Frequency Band 3.1-10.6 GHz Maximum Dimensions 20mm x 20mm Reflection < -20dB Isolation < -25dB Coupling = 10dB ±0.5dB Transmission Losses < 1dB Constant Group Delay As small as possible CER10-250 substrate Dielectric coefficient εr = 9.5
Vertically Installed Planar Circuit •Reduced the effective dielectric constant for even and odd mode from 2 to less than 0.2.
Stripline •VIP was not feasible because the gap was too wide. •Reduced effective dielectric constant for even and odd mode from 1.9 to less than 0.15.
First Approach broadband Chebyshev equal-ripple coupling response •S-parameters: simulated ≠ theoretical •Stronger transmission losses •Stronger reflections •Strong isolations •Uneven Band pass ripple •Cause: •frequency dispersion of the effective permittivity •Two propagation medium (air+substrate) •Effects: even and odd mode differences in •Impedances •phase velocities
Final Layout •stronger coupling to compensate for the precision of the manufacturing •all the transitions were designed to reduce coupling and transmission losses.
Prototype Final Layout Simulated S-parameters
•precision milling machine •dicing saw •flip chip bonder aligner.
Final Layout Simulated S-parameters
Conclusions •Unsatisfactory experimental results •New simulations with the SMA connectors and the extra microstrip length •Results matching the measurements for reflections •the substrate probably has a higher loss tangent of dielectric than its model •Explains the higher transmission losses of the real directional coupler •An improved model of the substrate has to be incorporated to the model and some modifications to decrease overall losses, insertion losses and increase isolation before this 3D architecture can be considered viable. References [1] Dipaolo F., Networks and Devices Using Planar Transmission Lines, Boca Raton, CRC Press LLC, 2000 [2] Konishi Y., Awai I., Fukuoka Y., Nakajima M., "A Directional Coupler of a Vertically Installed Planar Circuit Structure", IEEE Transactions on Microwave Theory and Techniques, vol. 36, No. 6, June 1988 [3] Le Kernec J., Klepal M., ―UWB radar for People Location and Tracking‖, Master’s Thesis, Adaptive Wireless Systems Group, Cork Institute of Technology, 2006 [4] Levy R., "General Synthesis of Asymmetric Multi-Element Coupled-Transmission-Line Directional Couplers", IEEE Transactions on Microwave Theory and Techniques, July 1963 [5] Levy R., "Tables for Asymmetric Multi-Element Coupled-Transmission-Line Directional Couplers", IEEE Transactions on Microwave Theory and Techniques, May 1964 [6] Sokol V., Waliwander T., Rulikowski P., Le Kernec J., ―The Experimental UWB Link‖ , 15th International Traveling Summer School on Microwaves and Ligthwaves, L’Aquila, Italie, 9-15 July 2005
5ème Colloque Interdisciplinaire en Instrumentation
