4-122 Ignition Quickshifter Stand Alone Unit Installation Instructions
Recommend Documents
service manual for your vehicle to locate the ignition ballast resistor (or loom
resistance ... advance (between 3,000 and 3,200 RPM). ... FLAT HEAD FORD V8.
Landscape, Visual Survey, Visual Toolbox, Visual LISP, Voice Reality, Volo,
Vtour, Wire, Wiretap, WiretapCentral, XSI, and XSI (design/logo). ..... 1 Insert the
AutoCAD disc(s) into your computer's drive. 2 In the ..... earlier than AutoCAD
20
Part No. DEB-1 for 1 970 and later Harley-Davidsons ... rotor is still free to rotate.
7. Remove the wire that connected the points and ignition coil. 8. ... Remove the
crank case timing hole plug and replace it with a transparent timing mark view.
DSS-1 for 1970' and later Harley-Davidsons ... Refer to a factory shop manual to
determine the timing mark for your particular engine. ... Run the engine at normal
operating temperature at 2,000 RPM. ... Remove the Dyna S and check that the.
Drill the holes between terminals at rotor height, facing away from the intake. ...
when you first turn on the ignition switch, the LED will flash rapidly 3 times.
NEVER switch the modes of the ACCEL After- ... time it takes to switch the ACCEL Afterburner coil ... would be one of th
are available for easy connection to early model Delco/GM HEI Systems, late
model ... KEEP ALL IGNITION SYSTEM WIRES AS FAR FROM SPARK PLUG
WIRES AS .... your vehicle's distributor and coil (see diagrams for more
information).
water in a small bore domestic central heating system where ... The wiring
diagram above shows relevant connections to a Honeywell junction box (Part No.
Sep 24, 2012 ... Design 2 - Single Line Diagram for Solar Light System . ... Appendix A; Site
drawings- Proposed sighting of solar system . ...... Child Clinic. 5. 1.
Simplified Block Diagram For a Maximum Power. Tracking Controller ....
photovoltaic industry by shifting from the use of reject space solar cells to cells
designed ... installation of nearly 150 stand-alone photovoltaic systems. A few
scattered.
With thanks to those who took the time to respond to the survey and to those who contacted us to give us feedback about
significant numbers of students who are not defined in this statutory sense, but who may have spent many years before th
Page 1 ... my own experience of family estrangement in the national press, detailing the moments where my ... This study
my own experience of family estrangement in the national press, detailing the moments ... This study aims to build this
Stand Alone is a young charity with a focus on supporting adults who are experiencing family ... the moments where my la
COPYRIGHT 2001-2009 METRA ELECTRONICS CORPORATION. 70-6522. INSTALLATION. INSTRUCTIONS. Chrysler/Dodge/Jeep. 2007-Up. Wi
symbols: WARninG indicates a potentially hazardous situ- ation which, if not
avoided, could ... cAUtion used without the safety alert symbol ...... The engines in
some vehicles, such as the Saturn. Vue, must be started periodically during
towing.
PLACING LAMPS AND SIGNS ON YOUR BUS. 3. INSTALLING ... 5.2. Running
requirements. 6. SPARE PARTS & REPLACING GLOBES .... is behind the dash.
FORD F150 (1997-2003) F150 SUPER CREW (2001-2003). F150 HERITAGE ...
FORD EXPEDITION (1997-2002) ... plastic parts of a vehicles dash. ... its cavity
and prop it up to the right to keep all the wiring and vacuum lines out of the way.
4-122 Ignition Quickshifter Stand Alone Unit Installation Instructions
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.
powercommander.com. Honda CBR250R. •. Installation Instructions. Parts List.
Honda CBR250R •
• • • • • • • •
Installation Instructions
Parts List
1 Quickshifter 2 Stand Alone 1 Shift Sensor (push) 1 Shift Rod 1 Installation Guide 2 Dynojet Decal 2 Cable Tie 2 Velcro 1 Alcohol Swab
• PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION •
•
4-122
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
•
Ignition Quick Shifter-Stand Alone Unit - 1
Fitting the Control Unit The Ignition Quickshifter control unit should be positioned so it does not exceed an operating temperature of 160°F and must be installed where it is protected from excessive vibration and harsh environmental elements. • • •
• • •
Connect the Ignition Quickshifter harness in-line of the stock wiring harness and Ignition coil (Fig. C). PURPLE wire goes to the spade terminal of the coil that is marked GREEN RED wire goes to the spade terminal of the coil marked BLACK
Remove the seat The fuel tank will need to be loosened so that you can hold it up to access the ignition coil. It does not need to be completely removed. Using the supplied velcro mount the control box to the top of the battery (Fig. A).
Figure C: Coil connection
Figure A: Mounting Unit •
Ground the Ignition Quickshifter to the bolt hole near the thermostat (Fig. D). This is located on the left side of the engine.
Route the wiring harness down the left side of the bike following the frame (Fig. B)
Figure B: Harness routing •
• •
4-122
www.powercommander.com
Figure D: Ground location •
Ignition Quick Shifter-Stand Alone Unit - 2
Fitting the Sensor • • •
Remove the stock shift rod from the shift linkage Screw the sensor all the way into the rear heim joint until it bottoms. Install the supplied shift rod in between the sensor and front heim joint. Adjust lever position and then tighten the locknuts.
•
The BLACK wire from the control unit can be connected to the grounding side of the clutch safety switch. When this wire is connected the unit will not KILL while the clutch is pulled in.
Troubleshooting No power up
Check for incorrect connections, blown fuses, poor negative battery terminal connections, and severed or trapped wires.
No quickshifter interrupt
Check for correct Ignition Quickshifter power supply. Verify the sensor output signal and the quickshifter parameters and programming has been carried out. Check for loss of tacho/RPM signal. Check for severed or trapped wires.
No quickshifter operation
Verify the quickshifter parameters and programming have been carried out. Check for loss of tacho/RPM signal. Check for severed or trapped wires.
Engine misfire
Verify the control unit mounting position and check for isolation from vibration. Check plug and play connections. Verify ignition coil type and suitability and if the ignition coil adapter connectors require fitting. Verify sensor output signal.
Figure E: Sensor mounting
Quickshifter System Operation To use the Ignition Quickshifter, make a full and positive gearshift with your foot in an upshift direction without using the clutch or rolling the throttle. Note: The gear lever must return fully to the rest position before the system resets itself for the next gear selection. The status LED will illuminate solid green whenever the Quickshifter sensor is in the trigger position. This status LED will flash in unison with the engine whenever the engine is running and if there is an ignition coil/RPM signal which is required for running mode. There will be no interrupt/quickshift below 2500 RPM. The unit comes with a set shift kill interrupt time. If for some reason you need to alter the kill time the optional Quickset adjuster can be purchased - part #61100014. Remove the BLACK plug from the harness and plug the Quickset adjuster in it’s place. This unit will give you a kill time range of 45-90ms.
