An Introduction To Praxair GDR

3 downloads 462 Views 1MB Size Report
2) Design monitoring program. 3) Design facilities ... Step 2: Monitoring Program. • Goal; To gather data ... Faciliti
Pilot Project Management for Gas Displacement Recovery (GDR) Flooding

[email protected]


GDR Pilots For Reserve Growth •

Key is Proper Planning – –

Determine goals, objectives, and strategy Goals: book reserves, test reservoir model data aquired

Important Tasks Include: 1) Initial reservoir characterization 

2) 3) 4) 5)

Identifying reserve growth method

Design monitoring program Design facilities Proper implementation Postmortem evaluation

Step 1: Reservoir Characterization Work Flow


Feed back Loop

Determine Reservoir Architecture

Establish Fluid-Flow Trends

Develop a Reservoir Model

Identify Reserve Growth Potential

How does the pilot design test the reservoir Model?

Reservoir Architecture Issues For EOR Pilots • Depositional Stacking Patterns – Flooding surfaces acting as flow barriers – Grain size and diagenesis causing high k variation

• Horizontal facies changes between injectorsproducers – Spatial facies variations cause anisotropic k

• Sealing and/or Offsetting Faults – Flow barriers – Interflow unit connectivity

Reserve Growth Applications 1. Pressure Maintenance  

Oil reservoirs Pressure maintenance condensate and retrograde condensate reservoirs

2. Miscible Displacement 3. Immiscible Displacement  

Oil: IWAG Gas cap gas

4. Mixed Gas Applications  

Driving agent for slug/buffer Mixed gases for density control

5. Gas Assisted Gravity Drainage

Step 2: Monitoring Program • Goal; To gather data to allow the evaluation of the pre injection prediction • Collect Fluid Input and Output Data, – Volumes, rates – Downhole Injection and production profiles

• Monitor Reservoir Conditions – Temperature and pressure

• Measure Hydrocarbon Saturation Change – Downhole wireline saturation logs – Volumetric recovery efficiency

Considerations for Monitoring Wells • Number of Monitoring Wells – Single well, vertical and displacement efficiency – Multiple wells, vertical sweep between wells, areal sweep efficiency, fluid mobility within the formation

• Location of Monitoring Wells – Test geologic interpretation

• Well Logistics – – – –

Drilling Coring, logging Completing Integrating data gathering

Injection Well Design Example from Bay St. Elaine Field

Screen wells for completion issues (Palmer et al., 1984)

Mobile Downhole Monitoring Unit

Monitor for the effect of injection on Oil Saturation: Example Oil saturation (%) 0 -12,790



Post Inj. Well A-18 Pre Inj. Well A-17

SubSea depth (ft)


Residual oil saturation to water influx Minimum = 0.154 Maximum = 0.376 Average = 0.221

Residual oil saturation to CO2 Minimum = 0.0 Maximum = 0.073 Average = 0.022







Apply through casing saturation tools •Reservoir Saturation Tool (RST) •Resistivity •Neutron

Step 3: Facilities Design • SAFETY FIRST • Site Preparation • Injection Facilities – Solvent delivery – Pumping equipment

• Production Facilities – Fluid rate and volume measurement – Fluid separation – Fluid handling

Facilities Design: Site Preparation • Pad Preparation – Size, layout, material

• Road Construction and/or Repair • Power Needs – Pumps, lights, trailers

• Water Needs

Facilities Design: Gas Delivery • Solvent Supply and Demand Status – Can you obtain the needed CO2 volumes when you want them?

• Diesel Source and Distribution. • Confirm the Routing of Solvent Distribution and Solvent Source.

Facilities Design: Pumping Equipment • • • •

Size Equipment to Rates and Pressures Needed Set Date to Ship the Equipment To the Site Set up the Equipment CO2 Heater

Facilities Design Production Facilities • Fluid Rate and Volume Measurement • Fluid Separation – 2 or 3 phase separator – Gas vented or flared ? – Obtaining permits

• Fluid Handling – Tanks – Production lines – Disposal

Surface Pumping Setup Storage vessels

Manifold Pump


Check Valve


Pump outlet temp. and pressure Oil Pipe pressure




EOR Pumping Setup

Control house Pump Heater Manifold

CO2 Injection P-T Profile Wellhead Tanker


Step 4: Proper Implementation • On Site Safety Plan • Work Flow Design • Continuous Process Checking Continuous pressure monitoring in the storage tanks, truck tanks, flow monitoring at the wellhead

Step 5: Postmortem Evaluation Pilot Postmortem Goals Geologic, engineering & economic assessment (compare to predicted)

• Evaluate Effectiveness of Facilities • Determine Success in Executing the Implementation Plan • Postmortem Evaluation of Monitoring Program – Was the gas injected at the designed conditions? – How did the gas move and work in the reservoir? – What was the deviation from the predicted results and why?

• Assessment of Injection – Buildup and falloff injection analysis

Summary •

Key is Proper Planning –

Determine goals, objectives, and strategy

Important Tasks Include: 1) Initial reservoir characterization  Identifying reserve growth method 2) Monitoring program design 3) Facilities design 4) Proper implementation 5) Postmortem evaluation