Assembly Instructions Standard 2 Seat Sofas Attention: If you have a floor that could be easily scratched or damaged please ensure you cover the arm feet with protective felt first.
Attention: Please ensure you have all parts before commencing assembly. Please read all of the instructions before commencing.
Attention: If you have purchased optional accessories. Please refer to the Optional Accessories assembly instructions which are supplied separately.
3. Assembling the Frame
1. Identifying the Parts 1x 2 Seat Front Facia 1x 2 Seat Front Foam
2x Back
3.2 Insert Strut 1 into the slot at an angle as shown.
2x Seat 2x Large Fibre Back Cushions
1x 2 Seat Rear Facia
3.1 Locate a 2 Seat Front Fascia, a 2 Seat Rear Fascia and four Strut 1s.
3.3 Press the front of Strut 1 down firmly into the slot as shown.
2x Small Back Cushion 2x Seat Cushion 1x RHS Arm Assembly
1x Arm Cover RHS
1x LHS Arm Assembly
3.4 Repeat with the other Strut 1s as shown.
1x 2 Seat Cover
3.5 Locate a 2 Seat Front Foam.
3.6 Remove the protective layer from the double-sided tape.
3.7 Lay the 2 Seat Front Foam tape side down on the front of the Frame Assembly as shown.
1x Arm Cover LHS
4x Strut 1
1x Rear Cover
1x Rear Foam
4. Fitting the Arm Cover
4.1 Locate the RHS Arm Assembly and the Arm Cover RHS.
1
4.2 If your sofa has steel feet remove the protective covers before fitting the cover.
2. Assembly of the Seats and Backs 2.1 Locate a Back and a Back Cushion.
2.2 Slide the Back into the Back Cushion as shown.
2.3 Repeat with the other Backs and Back Cushions.
2.4 Locate a Seat and a Seat Cushion.
2.5 Repeat with the other Seats and Seat Cushions.
2.6 Tie the straps.
2 3
4.3 Slide the Arm Cover RHS onto the RHS Arm Assembly from the rear as shown. Ensure the rear is located correctly
4.4 Pull the cover towards the front of the RHS Arm Assembly. Pull down firmly and locate the velcro strip onto the underside of the RHS Arm Assembly as shown.
4
4.5 Pull the rear of the cover down and locate the velcro strip onto the underside of the RHS Arm Assembly as shown.
4.6 Pull the flap in the middle of the opposite side underneath the RHS Arm Assembly. Attach it to the velcro strip as shown. 4.7 Repeat using the LHS Arm Assembly and the Arm
Cover LHS.
5. Fitting the Rear Cover
5.1 Locate the Rear Foam.
5.2 Remove the protective layer from the double-sided tape.
5.6 Locate the ends of the Rear Cover around the Rear Foam as shown.
7. Fitting the Backs and Seats
7.2 Position the Back ensuring the slots locate correctly as shown. Tuck the flap on the assembled Back in the inside of the assembled frame. See step 7.3.
5.3 Lay the Rear Foam tape side down on the back of the
Frame Assembly as
shown.
5.4 Locate the Rear Cover.
5.5 Position the Rear Cover onto the rear of the Frame Assembly as shown.
7.1 Locate the assembled Backs.
5.7 Pull the flaps underneath the Frame Assembly. Attach the velcro strips on the opposite flaps as shown.
7.3 Repeat with the next Back as shown. 7.4 Locate the assembled Seat Cushions. 7.5 Position the Seat Cushion as shown. 7.6 Repeat with the next Seat Cushion.
6. Fitting the Arm and Frame Covers
6.1 Locate the 2 Seat Cover.
6.2 Position the 2 Seat Cover onto the Frame Assembly as shown.
6.5 Locate the LHS Arm Assembly complete with the Arm Cover LHS and pushing down firmly, attach it to the end of the frame assembly as shown.
8. Fitting the Cushions
8.1 Locate the Large Fibre Back Cushions.
6.3 Locate the ends of the
2 Seat Cover around the 2 Seat Front Foam as shown.
8.2 Position as shown.
6.6 Repeat using the RHS Arm
Assembly as shown.
6.4 Pull the flaps underneath the Frame Assembly. Attach the velcro strips on the opposite flaps as shown.
The Company’s policy is one of continuous product improvement and the right is reserved to modify the information contained herein without notice.
