Axxess Stereos Installation Instructions

INSTALLATION INSTRUCTIONS FOR PART GMRC-02

GMRC-02 GM Class II Data Bus Interface 2000-2010 APPLICATIONS See inside front cover

KIT FEATURES • Provides accessory (12 volt 10 amp) • Retains RAP (if equipped) • Used in non-amplified systems or when removing amplified system • Retains all warning chimes • Small in size

INTERFACE COMPONENTS • GMRC-02 data interface • 10-pin to 24-pin GM harness with stripped leads

TOOLS REQUIRED • Cutting tool • Crimping tool • Tape • Connectors (example: butt-connectors, bell caps, etc.)

ISO

M4

M3.5

IGNITION TERMINALS

M2.6

M3

6 2.5

WIRE CUTTER

1.5

M5

GMRC-02

Applications Note: The GMRC-02 is designed to be used in non-amplified GM vehicles or in vehicles that the OEM amplifier has been bypassed; Onstar is not retained in either case. The GMRC-02 retains all the factory warning chimes that would be lost when the OEM radio is removed. It will also provide a 10 amp 12 volt switched accessory for proper radio operation, and retain the RAP (Retained Accessory Power) feature if equipped. Buick Allure Century Lacrosse Rainier Rendezvous Terraza

2005-2009 2004-2005 2005-2009 2004-2007 2002-2007 2005-2008

chevrolet Avalanche Cavalier Colorado Express Impala Malibu Malibu classic Monte Carlo Silverado pickup classic Silverado pickup (all models) SSR Suburban Tahoe Trailblazer Uplander Venture van

2003-2006 2000-2005 2004-2010 2003-2007 2000-2005 2001-2003 2004-2005 2000-2005 2007 2003-2006 2003-2006 2003-2006 2003-2006 2002-2009 2005-2008 2000-2005

GMc Canyon Envoy Savanna van (full size)

2004-2010 2002-2009 2003-2007

(GMC continued) Sierra classic Sierra Yukon/Yukon XL

2007 2003-2006 2003-2006

huMMer H3

2006-2009

isuzu Ascender I Series pickups

2003-2008 2006-2008

oldsMoBile Alero Bravada Intrigue Silhouette

2001-2004 2002-2005 2002 2000-2004

Pontiac Aztec Grand Am Grand Prix Montana sv6 (Canada) Montana Sunfire

2001-2005 2001-2005 2004-2008 2005-2008 2000-2005 2000-2005

saaB 9-7X

2005-2009

saturn Relay

2005-2007

Caution: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. Note: Refer also to the instructions included with the aftermarket radio.

GMRC-02

Connections to be made From the 24-pin harness: • Connect the Yellow wire to the radio’s 12-volt battery or memory wire. • Connect the Black wire to the radio’s ground wire. • Connect the Gray wire to the right front positive speaker output of the aftermarket radio. • Connect the Gray/Black wire to the right front negative speaker output of the aftermarket radio. • Connect the Green wire to the radio’s left rear positive speaker output. • Connect the Green/Black wire to the radio’s left rear negative speaker output. • Connect the Purple wire to the radio’s right rear positive speaker output. • Connect the Purple/Black wire to the radio’s right rear negative speaker output. • Connect the Blue/White wire to the radio’s antenna turn on wire. • The orange wire is not used in this application. From the 10-pin: • Connect the red wire to the ignition wire of the aftermarket radio. • Connect the White wire to the left front positive speaker output of the aftermarket radio. • Connect the White/Black wire to the left front negative speaker output of the aftermarket radio.

Installing the GMRC-02 • With all connections completed to the aftermarket radio, plug the 24 pin harness into the vehicles wiring harness. note: Some minor modifications may be necessary to the sub dash cavity to accommodate the GMRC-02. • Cycle the key by turning the ignition on then back off, then on again to test the radio.

Testing the GMRC-02 • Turn the ignition on if not already, and then turn the radio on to verify that the radio works. Check balance and fader controls for proper operation. • Now close all the doors with the radio on and turn the key off. The radio should be still on until one of the doors is opened.

INSTALLATION INSTRUCTIONS FOR PART GMRC-02

iMPortant WarninG This product includes instructions for installation which must be carefully followed. The instructions are worded in such a manner to assume that the installer is capable of completing these type of electronic installations. If you are unclear as to what you are instructed to do or believe that you do not understand the instructions so as to properly and safely complete the installation you should consult a technician who does have this knowledge and understanding.

AXXESS ACCESSORIES

STEREOS