Basic Online Training Course - Software download - Eiva

NaviSuite Online Training NaviPac – NaviScan – NaviEdit/NaviModel

Training Schedule: Day 1:

Day 2: Day 3: Day 4: Day 5:

Introduction Installation of the Software NaviPac Configuration NaviPac Online NaviPac (Helmsman’s Display) NaviScan Configuration NaviScan Online NaviEdit NaviEdit (Continued) NaviModel/Online3D Patch Test

Scope of the Online Course Learning Objectives: The course is structured around a general curriculum with the aim being to furnish the trainees with a broad understanding of the EIVA NaviSuite online software solutions and make them confident in using the software on a vessel. To enhance this, typical construction support and acquisition scenarios are used as examples throughout the training. For the most part, the course is conducted as hands-on training, thus taking advantage of the comprehensive simulation functionalities that have been implemented into the NaviPac and NaviScan software solutions. By the end of the course, delegates will be able to:  Install the relevant NaviSuite software packages.  Understand the basic architecture of NaviPac & NaviScan.  Configure NaviPac & NaviScan with common instruments, geodesy, objects etc.  Run various programs for different tasks (calibration, documentation, QA).  Log survey data for different tasks and in different formats.  Start, configure and use the Helmsman’s Display program.  Create and manipulate waypoints and runlines.  Use different map background formats.  Control the logging process from the Helmsman’s Display.  Start and configure the Online3D utility.  Conduct simple editing of multibeam data in a NaviEdit/NaviModel environment.  Conduct a Patch Test calibration in NaviModel/NaviEdit. Target Group: The course is aimed towards surveyors who have some experience with offshore survey work and basic knowledge of hydrographic surveying. Entry Level: No prior knowledge of the EIVA software solutions is required. The language of instruction is English. Duration: The duration of the course is 5 days, from 9 A.M. to 4 P.M., including breaks. Completion: Upon completion, a dedicated EIVA Training Certificate will be issued.

Scope of the Online Course

Training Curriculum I: • Introduction: • The Company, EIVA • Download and Knowledgebase • The Training Site

• NaviPac Configuration: • • • • • • •

Installation Organisation of the NaviPac System Config versus Setup Geodetic Parameters Objects Instrument Settings Exercises

•

NaviPac Online: • • • • • • • • • • • • • • •

Navigation Object Positions GPS Status Attitudes I/O Monitor Raw Data – Instrument Spy Alarm Monitor Data Acquisition Event Settings Calibrations Calculations Data Logging EIVAStat (EOL Reporting) Report Generator Online QC Tool

Training Curriculum II: • NaviPac (Helmsman’s Display): • Helmsman’s Display • Connection to NaviPac • Privilege Level and Broadcast • Views • Objects • Runlines • Displaylines • Waypoints • Models and GeoTiffs • Printing • Remote Helmsman’s Display • 3D Visualization

• NaviScan: • • • • • • • • • • • •

Installation of NaviScan Organisation of the NaviScan System Setting up Interfacing Parameters Defining Global Parameters NaviScan Online NaviScan Views Input Monitor and Alarms Advanced Online Settings NaviScan Logging Playback Facilities NaviScan Raw Data NaviScan Converters

Training Curriculum III: • NaviEdit: • • • • • • • • • • •

Installation of NaviEdit SQL-Server Database Management Importing of Data The Header Editor The Data Editor The Planview Editor Batch Editing Using SVP- and Tidal Data Exporting of Data Link to/from NaviModel/Online3D • S-CAN Auto Cleaning in NM3

Patchtesting within NM/Online3D: • Installation of NaviModel/Online3D • Patchtest Theory: • Calibration Sequence • Latency Calibration • Pitch Calibration • Roll Calibration • Heading Calibration • Training with Data • Utilizing the Results: • Within NaviScan • Within NaviEdit

Download & Knowledgebase The EIVA Download site gives users the possibility to download latest versions and patches of the various software packages. A user can sign up for login access and can subsequently receive an e-mail notification when releases occur on the various folders.

In the Knowledgebase, FAQ from the EIVA user community, are listed and organized relative subjective items like: software package, popularity, age (latest addition) etc. Users are also given the opportunity to submit a question that will then be upgraded and included in the knowledgebase.

Training & Documentation Site The Training & Documentation site contains all documentation and training material associated with the EIVA Softand Hardware. It should therefore be installed whenever installing the EIVA software (is not a requirement for the proper functioning of the associated software. The documentation includes all on-line help, manuals, powerpoints, reports, papers, training documents available for the EIVA software packages as well as for the EIVA hardware. The site is designed to be executed in off-line mode (with no connection to the Internet), however some of the items will only provide optimum functionality if an Internet connection has been established. Observe that the site can also be reached at the EIVA Website http://download.eiva.dk/onlinetraining/index.htm

Training & Documentation Site II The Training & Documentation site is subdivided into subpages that relate to the different modules that constitute EIVA NaviSuite. The Online packages have two main subpages, related to: •

NaviPac

•

NaviScan (shown here)

The NaviPac Subpages is further divided into two pages: •

Modules

•

Interfaces

Software Installation The Software Installer lists the software packages in the sequence shown to the left. During installation, remember to use settings.

always default

The EIVA Online Flow

NaviPac - I

NaviPac - II

NaviPac - III

NaviPac - IV

NaviPac - V

NaviPac - VI

NaviPac - VII Multiple Map Views in the Helmsman’s Display Multiple Runline Control Views

NaviScan - I

NaviScan - II NaviScan Config

On-Line/Acquisition

NaviScan - III

NaviScan - IV

NaviScan - V

The NaviEdit Flow

NaviEdit JobPlanner

Patch Testing – in NaviModel/Online3D Patch Testing can be performed in NaviModel and in the Online3D application. In the latter case, no dongle is required.

Patch Test – Purpose of the Calibration A multibeam Patch Test calibration serves a dual purpose: a.

b.

To determine the mount angles of the multibeam transducer relative to the three axes of the local coordinate system of the vessel/ROV. These three figures are often referred to as the roll-, pitch- and heading mount angles. To confirm the relationship between the time-tagging on the multibeam data and the time-tagging on the position data. This figure is often referred to as the latency or as the time value.

EIVA Online Modules • In addition to the standard functionalities, NaviPac include the following modules: • • • • • • • •

Tug and Barge Management with Rig Move. Catenary calculations and visualizations. Cablelaying/Pipelaying. 2D Seismic navigation. Dredging. Scour monitoring. Sonar Display. Online 3D visualization and generation of DTM.

Tug and Barge Management w. Rig Move • • • • • •

Add-on to NaviPac. Barge and tug license versions. Multiplex Telemetry or LAN capabilities. Up to 16 anchors w. 3 midline buoys each. Unlimited number of tugs. Dedicated planning and reporting tools.

Catenary Calculations and Visualizations • • • •

NaviPac, NaviCat & NaviModel. Rig move/TMS pipe lay cable lay capabilities. NaviPac supplies positions (vessel, tugs, anchors etc.). NaviCat does the catenary calculations. NaviModel/Online3D handles the visualization.

Cablelaying/Pipelaying Support • • • •

Barge route. Barge track – offset control. Cable overlength. Touch down monitoring.

2D Seismic Navigation • •

• •

NaviPac for navigation etc. Dedicated drivers for streamer/tailbuoy positioning and navigation header output. Seismic control via event trigger. NaviEdit for sensor editing and navigation reporting.

Dredging •

NaviSuite UCA Module: NaviPac & NaviModel/Online3D: •NaviPac executed in incognito mode, linking to the excavator. •NaviModel visualizing and updating the scenario. •NaviModel supplying additional tools for preparation, reporting, volume calculations. etc.

Scour Monitoring •

NaviScan & NaviModel. • NaviScan (Scour module): automatic 24/7 collection of data, at predefined intervals. • NaviModel performs automatic cleaning and creates the DTMs with no user intervention. • NaviModel supplying additional tools for visualization, automatic reporting, volume calculations. etc.

SonarDisplay • • •

NaviScan real time display of real sidescans and MBE sidescan options. Use in combination with target generation and editing tool. Playback functionalities.

Real-time 3D Visualization and DTM • • • •

NaviPac, NaviScan & Online3D. NaviPac handles and supplies position information. NaviScan supplies multibeam information. Online3D presents this in a 3D environment, including real time DTM.