Description. In addition to recording âelectric potential and âLPR measurements, this node has an integrated semicon
Camur II Controller software. Camur II Monitor and Camur II Server, software running on the Camur II Controller. Descrip
For monitoring and alarm triggering. Description. The Camur ... In Camur II software you select the alarm source and set
Fuse 7.5 A (Blade type, brown mini fuse, vehicle type). Output turns off ... software. Note! Cables to sense must be use
The P Quick node supports recording types Monitor, Monitor Extended and Decay in Camur II software. HS export code: 9031
Mitsubishi Electric Corporation Nagoya Works is a factory certified for ISO14001.
(standards for environmental management systems) and ISO9001(standards ...
Sep 26, 2016 - SUBMISSION OF LIST OF PEPT REGISTRANTS FOR S.Y. 2016-2017 ... Letty T. Lopez, SGOD at email address letty
Sep 23, 2015 - Instructional Managers // Service Providers. FROM: MANUELA S. ... CRAFTING OF THE FIRST DIVISION ALS NEWS
Where v is the peripheral speed of the gear in m/sec. 4.a) Explain the following terms of the spring: · (i) free length
... memorability) and limit user error (few and easily remedied errors) [9]. .... For simplifying access to a popular groupware system (i.e. Lotus Notes),. Takagi et al.
Ans:London. 28.Name the clouds which cause rainfall. Ans:Startus. 29. ... Ans:Internet Service Provider. 70.The extensio
If the annular space is filled with oil of viscosity · 14 poise; calculate the speed of descent of piston in vertical po
(b) Explain with the block diagram the Armstrong method of FM generation. 4. (a) Distinguish between negative peak clipp
80 mA @ 12 V (from bus). Max no. of nodes. 100. Weight node w/connectors. 130 g. Power supply (included). 24 V / 2.5 A.
Camur II Ethernet Interface Interface between the Camur II Bus and ethernet Description Camur II Ethernet Interface powers the Camur II Bus, and connects the bus to ethernet. Camur II Ethernet Interface is delivered with a 24 V/2.5 A power supply. Technical data Power in/out (bus) Power consumption Max no. of nodes Weight node w/connectors
12-48 VDC 80 mA @ 12 V (from bus) 100 130 g
Power supply (included) Dimensions (WxHxD) - w/connectors and clip Weight power supply
24 V / 2.5 A 68 x 81 x 34 mm 80 x 132 x 40 mm 280 g
Ethernet cable included
1 m / 30g
Integrated DIN-rail mounting clip. The Camur II Ethernet Interface and right side bus connector is protected from reverse polarity voltage applied to the 10-pole connector. Connectors Bus Via right side bus connector (must be ordered separately). (+, - , H , L) Ethernet The Ethernet connector is located on the left side of the node box. Reset The node may be reset by pushing the reset button through the tiny reset-hole on the top side. Keep the button pressed for ● 2-3 seconds to reset node to retrieve IP address from DHCP ● 8-12 seconds to reset to static IP address (default two last digits of serial number plus 100. For example, serial number that ends on 32 results in IP 192.168.0.132 )
HS export code: 9031 8090 Camur II Ethernet Interface, Rev 1 - March 2017 Page 1 of 2
Input / output Quick plug connector
+
power supply, V+
-
power supply, V-
H
bus signal high
L
bus signal low
D1
watchdog 1 (on system reset: D1 = V+)
D2
watchdog 2 (D2 = V-)
Note! Make sure no part of the bus has lower voltage than 10.5 V.
HS export code: 9031 8090 Camur II Ethernet Interface, Rev 1 - March 2017 Page 2 of 2
