Gm1590AB - Sonic Electronix

13 downloads 5522 Views 624KB Size Report
Use a panel removal tool to pry out radio dash bezel, unplug electrical connectors and remove bezel. 2. .... 2000-05 Buick LeSabre ... 1995-96 Buick Regal ... Extract (6) plastic push-pin fasteners from under front edge of upper dash pad.
1994-99 1994-99 1994-96 1994-98

oldsmobile eighty-eight oldsmobile LSS oldsmobile Ninety-eight oldsmobile Regency

iN-dASh iNSTALLATioN kiT foR

RAdio RemovAL:

1.  2.  3.  4.  5. 

Open glove box, and remove (2) 9/32" Hex head screws at edge of woodgrain panel. Carefully  pull out woodgrain trim to release remaining snap clips and remove. Extract (2) 9/32" Hex screws from bottom edge of center dash/radio bezel. Carefully lift up and out on center dash/radio bezel, unsnap (3) clips from the top, and remove the bezel. Extract (3) 9/32" Hex screws holding radio, unplug connector, antenna and remove radio.

1998-02 oldsmobile intrigue

See iLLUSTRATioN "C"

RAdio RemovAL:

1.  Using panel removal tool, pry off radio bezel and remove.  2.  Extract (3) 9/32" screws securing radio, disconnect and remove.

2001-04 Pontiac Aztec

See iLLUSTRATioN "A"

RAdio RemovAL:

1.  2.  3.  4.  5. 

Gm1590AB

See iLLUSTRATioN "A"

Remove cup holder inserts. Extract (1) screw from bottom of cup holder. Carefully remove shifter trim panel with cup holders. Extract (2) #15 torx from bottom of radio climate control bezel. Disconnect and remove radio.

2000-06 Pontiac Bonneville

See iLLUSTRATioN "A"

RAdio RemovAL:

Note: The factory stereo provision is for a Double DIN radio. 1.  Remove (2) plastic fasteners from dash bezel above instrument cluster. 2.  Pull bezel out and up, disconnect and remove. Pull radio out by depressing fi nger tabs, and remove. See iLLUSTRATioN "A"

2001-05 Pontiac Grand Am RAdio RemovAL:

1.  Use a panel removal tool to pry out radio dash bezel, unplug electrical connectors and remove bezel. 2.  Extract (3) 7MM screws from radio.

SeLeCT 1992-UP GeNeRAL moToRS / hUmmeR / SUzUki / iSUzU / vehiCLeS WiTh oveRSize RAdio/m3000 2002-04 ToyoTA mATRiX VEHICLE APPLICATIONS: BUiCk

1997-05 1995-99 2000-05 1995-99 2000-05 2004-UP 1995-96 1997-04 2002-05 1996-99 1995-96 1996-98

CENTURY...................... 2 LE SABRE ..................... 3 LE SABRE ..................... 3 PARK AVE...................... 3 PARK AVE...................... 3 RAINIER ........................ 7 REGAL........................... 3 REGAL........................... 3 RENDEZVOUS .............. 3 RIVIERA ......................... 3 ROADMASTER .............. 4 SKYLARK ....................... 4

CAdiLLAC 2003-06 2003-06 2003-06

ESCALADE .................... 4 ESCALADE ESV ............ 4 ESCALADE EXT ............ 4

ChevRoLeT 2003-06 2002-04 2000-05 2004 2004-UP 2001-02 2003-UP 2000-05 2001-03 1998-01 2000-05 2002-03 2004 2003-06 2007

AVALANCHE ................. 4 BLAZER ......................... 4 CAVALIER ..................... 4 CLASSIC ....................... 5 COLORADO .................. 5 EXPRESS ...................... 5 EXPRESS ...................... 5 IMPALA .......................... 5 MALIBU ......................... 5 METRO .......................... 5 MONTE CARLO............. 5 S-10 PICKUP ................. 6 S-10 PICKUP ................. 4 SILVERADO ................... 4 SILVERADO CLASSIC... 4

See iLLUSTRATioN "d"

2002-Up Pontiac vibe 2002-04 Toyota matrix RAdio RemovAL:

ChevRoLeT (Cont'd)

2004-UP 2003-06 2003-06 1998 1999-UP 2002-UP 2000-05

SSR ............................... 6 SURBURBAN ................ 4 TAHOE .......................... 4 TRACKER ...................... 6 TRACKER ...................... 6 TRAILBLAZER ............... 6 VENTURE ...................... 6

Geo

1995-UP 1995-97

METRO .......................... 6 METRO .......................... 5

GmC

2004-UP 2002-UP 2002-04 2001-02 2003-UP 2003-06 2007 2002-04 2003-06 2003-06

CANYON ....................... 5 ENVOY .......................... 7 JIMMY ........................... 4 SAVANA ........................ 5 SAVANA ........................ 5 SIERRA .......................... 4 SIERRA CLASSIC ......... 4 SONOMA....................... 4 YUKON .......................... 4 YUKON XL ..................... 4

hoNdA 1998-02

PASSPORT .................... 7

hUmmeR 2003-06 2003-UP

iSUzU

1998-00 2003-UP 1998-02

HUMMER H1 ................. 7 HUMMER H2 ................. 7 AMIGO........................... 7 ASCENDER ................... 7 RODEO.......................... 7

GM03B GM05B

See iLLUSTRATioN "C"

RAdio RemovAL:

PoNTiAC 2001-04 2000-06 2001-05 2000-05 2000-05 2002-UP

SUzUki 2002 1998-02 1999-UP 1996-98 1995-UP 2002

ToyoTA 2002-04

ACHIEVA ....................... 4 ALERO........................... 7 AURORA........................ 7 BRAVADA ...................... 4 BRAVADA ...................... 7 CUTLASS SUPREME .... 3 EIGHTY-EIGHT .............. 8 INTRIGUE ...................... 8 LSS ................................ 8 NINETY-EIGHT .............. 8 REGENCY ..................... 8 SILHOUETTE ................ 6 AZTEC ........................... 8 BONNEVILLE ................ 8 GRAND AM ................... 8 MONTANA ..................... 6 SUNFIRE ....................... 4 VIBE............................... 8 AERIO............................ 8 ESTEEM ........................ 8 GRAND VITARA............. 6 SIDEKICK ...................... 6 SWIFT............................ 6 XL-7 ............................... 6 MATRIX.......................... 8

GM05B

PRovide eASy CoNNeCTioN of yoUR CAR STeReo To fACToRy WiRiNG hARNeSS.

1994-Up GM

2002 Suzuki Aerio

1996-98 1995-00 1995-00 1998-01 2002-04 1995-99 1994-99 1998-02 1994-99 1994-96 1994-98 2000-04

FACTORY WIRING CODES CAR STEREO CONNECTORS GM03B

1.  Carefully pry out dash/radio trim bezel using nylon tool or panel removal tool. Lift from bottom and remove. 2.  Unplug switch harnessess and remove. 3.  Extract (4) 10mm bolts securing radio brackets, disconnect and remove.

oLdSmoBiLe

2000-Up Chevrolet,  Metro/Tracker/Prizm/ Venture Speaker

GM09SR 2000-Up GM Non Bose, Non OnStar  Application

MDA-1B

GM09SR

MDA-1B

Micro/Delco Antenna  Adapter

1.  Unsnap dash trim bezel and remove. 2.  Extract (4) screws from radio, disconnect and remove. See iLLUSTRATioN "C"

1998-02 Suzuki esteem RAdio RemovAL:

1.  2.  3.  4.  5. 

Remove vent/heat control knob tips. Extract (1) screw from below hazard/defroster switch area. Carefully pop out dash panel and remove. Remove (1) push-pin type fastener from each rear side of the console near parking brake. Extract (4) screws holding radio/drink holder in, unplug connectors, antenna lead and remove radio.

LiABiLiTy diSCLAimeR

This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/codes and  information pertaining to installation of this kit GM1590AB. Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the automobile during the installation of components while using this booklet.

If you have any further questions, call: 8

©2007 SCOSCHE INDUSTRIES, INC.

TeCh heLP 1-800-621-3695, ext. 3 SI 08/07 - GM1590AB (3000455)

INTRODUCTION / PRELIMINARY This premium installation kit is for 1992-Up General Motors/Hummer/Suzuki/Isuzu vehicles with oversize radio/M3000; 2002-04 Toyota  Matrix. Included are all the parts you need to mount your car stereo, cassette, or CD player into your vehicle’s dash. Refer to the individual  instruction in this manual to remove your vehicle’s factory radio and assemble the kit.

2002-Up GmC envoy 2004-Up Buick Rainier 2003-Up isuzu Ascender

CAUTioN: diSCoNNeCT yoUR vehiCLe’S NeGATive BATTeRy TeRmiNAL BefoRe The iNSTALLATioN To

RAdio RemovAL:

heLP PReveNT eLeCTRiCAL dAmAGe. We ReCommeNd The USe of A voLT/ohm meTeR oveR A TeST LiGhT To CheCk WiRiNG. A TeST LiGhT oR GRoUNded WiRe PRoBe CAN CAUSe dAmAGe To The vehiCLe'S ComPUTeR ANd/oR diAGNoSTiC SySTemS. Avoid ALL fACToRy AiRBAG WiRiNG - AiRBAGS CAN ACCideNTALLy dePLoy CAUSiNG SeRioUS iNJURy oR deATh. NoTeS:

•  See your vehicle’s instructions for any special tools your installation might require. •  Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting instructions.

See iLLUSTRATioN "B"

1.  Open center console lid and extract (2) Philips screws from front of console, lift out rubber pads and extract (4)  more Philips screws from under. Remove console insert. 2.  Extract (2) 9/32" screws from console cavity. 3.  Remove rubber pad from front cup holder and extract (1) 9/32" screw from under. 4.  Extract (4) Philips screws from sides of carpeted panel directly under radio and climate controls, pull it down and  out of the way. 5.  Pull center console back and down to get to (2) Philips screws on bottom of radio bezel. Pry bezel out from top to  bottom, disconnect, and remove. 6.  Extract (3) 9/32" screws securing radio.

1998-02 honda Passport 1998-00 isuzu Amigo 1998-02 isuzu Rodeo iLLUSTRATioN "A"

RAdio RemovAL:

iLLUSTRATioN "B" CUT ANd Remove CoRNeRS

iLLUSTRATioN "C"

iLLUSTRATioN "d"

iLLUSTRATioN "e"

1.  2.  3.  4.  5.  6. 

Remove ashtray cup from ashtray. Extract (1) screw from rear of ashtray cavity. Carefully unclip trim bezel located around radio/lighter assembly. Disconnect wire harness from the lighter and then remove the trim assembly. Extract (4) screws securing the radio to the subdash. Disconnect harness from radio as well as antenna adapter and remove radio.

2003-06 hummer h1

See iLLUSTRATioN "A"

RAdio RemovAL:

1.  Remove (4) Screws securing radio/dash bezel & remove. 2.  Remove (3) 7MM hex screws holding radio, unplug and remove.

BRACKET PREPARATION

foR ALL vehiCLeS

See iLLUSTRATioN "e"

Remove

1.  Remove the (2) top and (2) bottom mounting tabs located on the  trimpanel.

2003-Up hummer h2

2.  Attach brackets to trim ring by sliding into corresponding slots. Attach  radio to brackets with screws supplied with radio.

1.  2.  3.  4.  5.  6.  7. 

See iLLUSTRATioN "A"

RAdio RemovAL:

Remove

Open center console storage and extract 4 screws securing hinged lid. Remove Torx lock nut holding Shift lever (Nut is facing forward) and Slide shift lever off. Use a panel removal tool to carefully pop up cup holder/gear indicator plate. Extract (2) 7mm hex screws at bottom of center dash bezel (revealed in previous step #3). Extract (2) 7mm hex screws from center dash bezel (near each vent). Carefully pry out on center dash bezel to unsnap, unplug and remove. Extract (3) 7mm hex screws holding radio, unplug and remove.

1995-00 oldsmobile Alero

See iLLUSTRATioN "A"

RAdio RemovAL:

1.  Unsnap shifter panel and leave it loose. 2.  Using a panel removal tool remove radio trim bezel (there are a total of six snaps) unplug and remove. 3.  Extract (3) 9/32" screws holding radio, unplug and remove.

1995-00 oldsmobile Aurora NOTE:

FOR THESE APPLICATIONS USE THE SHADED BRACKETS. CUT OFF THE REMAINING BRACKETS AND DISCARD. (SEE ILLUSTRATIONS).

1997-05 Buick Century

See iLLUSTRATioN "A"

RAdio RemovAL:

1.  Carefully unsnap dash bezel and remove. 2.  Extract (3) 7MM screws securing radio, unplug connectors, antenna lead and remove radio.

See iLLUSTRATioN "A"

RAdio RemovAL:

1.  Extract (1) screw from bottom lower dash panel at right of glove box. 2.  Open glove box and pop out small lower dash panel along the right side. 3.  Carefully pop out fuse box cover at right side of dash and extract (1) screw from the dash bezel at the right of the  air vent. 4.  Extract (2) screws at the bottom of the lower ashtray/lighter dash section pop out and remove. 5.  Extract (1) screw from the right driver’s side lower dash panel and one panel popper from the left side. 6.  Carefully pop out the driver’s side lower dash panel and remove. 7.  Put the vehicle into fi rst or low gear, and tilt the steering column adjustment all the way down and pull outward on  the complete dash panel to unsnap, unplug, and remove panel. 8.  Extract (3) 7 MM screws holding radio, unplug connector, antenna cable and remove radio.

2

2002-04 oldsmobile Bravada

See iLLUSTRATioN "A"

RAdio RemovAL:

NoTe:  The factory radio provision is for a DIN sized radio.  There is no kit available at this time. 1.  Open arm rest and remove both rubber screw covers. 2.  Remove (6) Philips head screws. 3.  Carefully pull up console and shift gear to 1st. 4.  Locate and remove (2) Philips head screws at bottom of center dash panel. 5.  Carefully pull away center dash. 6.  Remove (3) 9/32" screws.

7

2002-03 Chevrolet S-10 Pickup

SEE ILLUSTRATION "B"

RADIO REMOVAL:

1.  Turn ignition on and shift vehicle into first if an automatic. 2.  Extract (1) 9/32" screw from above gauge cluster. 3.  Extract (5) 9/32" screws from unerdash pane; and remove. 4.  Extract (2) 9/32" screws from bottom of dash bezel, and carefully pry out bezel. CAUTION:  When you go to pull bezel over hazard switch be very careful not to break switch. Disconnect and remove bezel. 5.  Extract (3) 9/32" screws securing radio, disconnect, and remove.

2004-Up Chevrolet SSR

SEE ILLUSTRATION "A"

1995-99 Buick Le Sabre  1995-99 Buick Park Avenue

SEE ILLUSTRATION "A"

RADIO REMOVAL:

1.  Pop out small narrow trim panel around trunk/fuel door buttons and extract on screw at left. 2.  Carefully pop out small narrow trim panel around a/c heater controls and bottom of passenger airbag. Extract (1) screw at far right and (1) screw above glove box. 3.  Using a panel removal tool or small flat-blade screwdriver pop out all (4) dash vents and remove (1) screw behind each vent. 4.  Make sure the parking brake is on, then insert the key and turn to the "on" position. 5.  Put the vehicle into first or low gear, and tilt the steering column adjustment all the way down and pull outward on the complete dash panel. 6.  Extract (3) 7 MM screws holding radio, unplug connector, antenna cable and remove radio.

RADIO REMOVAL:

1.  Using a panel removal tool remove the aluminum trim that separates the dash. 2.  Remove six (6) 7MM hex screws securing the dash panel. 3.  Remove the dash by pulling towards you. Use caution when removing the dash around the passenger’s air bag. Bend the sides of the passenger air bag cover to release the passenger side of the dash. 4.  Remove three (3) 7MM hex screws securing radio to the dash. Disconnect and remove the radio.

1998 Chevrolet Tracker 1996-98 Suzuki Sidekick

SEE ILLUSTRATION "C"

RADIO REMOVAL:

1.  2.  3.  4. 

Remove the ashtray and extract the (2) screws from behind. Remove AC/vent control knobs, pop out the vent control/temperature panel and extract the (2) screws from behind. Pop out the radio dash bezel and remove. Extract the (4) screws securing the radio, unplug all connectors and remove.

1999-Up Chevrolet Tracker 1999-Up Suzuki Grand Vitara 2002 Suzuki XL-7

1.  2.  3.  4. 

Open driver’s door and use a panel removal tool to unsnap dash end cap and remove. Extract (2) screws from bottom of steering column plate, then remove cover. Carefully remove instrument panel with panel removal tool. Extract (2) 9/32" screws securing radio, disconnect and remove.

1995-96 Buick Regal  1995-99 Oldsmobile Cutlass Supreme

SEE ILLUSTRATION "A"

RADIO REMOVAL:

1.  Tilt steering column down to lowest position. 2.  Unsnap dash bezel and remove. 3.  Extract (3) 7MM screws securing radio, unplug connectors, antenna lead and remove radio. PLEASE NOTE:  Back of dash cavity may need modification. SEE ILLUSTRATION "A"

Radio Removal:

Remove the ashtray and extract the (2) screws from behind. Extract the (1) screw from above the radio. Pop out the radio dash bezel and remove. Extract the (4) screws securing the radio, unplug all connectors and remove. SEE ILLUSTRATION "B"

RADIO REMOVAL:

Extract (2) 9/32" screws from dash bezel. Extract (1) Philips head screw from under air conditioner control. Extract (2) 9/32" screws from above brake pedal. Extract (2) 9/32" screws from underneath. Extract (2) Philips head screws from instrument bezel, disconnect, and remove.

2000-05 Chevrolet Venture 2000-04 Oldsmobile Silhouette 2000-05 Pontiac Montana

SEE ILLUSTRATION "B"

  1.  Unsnap gear selector trim bezel, unplug and remove the bezel. Extract (2) 10 MM bolts from metal console bracket.   2.  Open armrest storage, lift up rubber mat and extract (2) 10 MM bolts from underneath.   3.  Extract (2) 10 MM bolts from the front sides of the console, which are concealed up under the dash.   4.  Slide shifter back into low gear, push down on spring-loaded shifter trim and pull complete center console to rear of the vehicle, allowing the center lower dash section (attached) to unsnap from the dash.   5.  Extract (1) screw from bottom lower dash panel at right of glove box.   6.  Open glove box and pop out small lower dash panel along the right side.   7.  Carefully pop out fuse box cover at right side of dash and extract (1) screw from the dash bezel at the right of the air vent.   8.  Extract (1) screw from the lower right of driver’s side lower dash panel and one panel popper from the left side.   9.  Carefully pop out the driver’s side lower dash panel and remove. 10.  Extract (3) 7 MM screws holding radio, unplug connector, antenna cable and remove radio.

2002-05 Buick Rendezvous 

SEE ILLUSTRATION "A"

RADIO REMOVAL:

RADIO REMOVAL:

1.  Remove ashtray and extract (2) Phillips head screws from behind. 2.  Unsnap perimeter of radio trim bezel, lift away and remove. Extract (3) Phillips head screws securing radio, lift away, disconnect and remove.

1995-Up Geo Metro 1995-Up Suzuki Swift

SEE ILLUSTRATION "B"

RADIO REMOVAL:

1.  2.  3.  4.  5.  6. 

Radio Removal:

1997-04 Buick Regal

2002-Up Chevrolet Trailblazer 1.  2.  3.  4.  5. 

SEE ILLUSTRATION "A"

SEE ILLUSTRATION "C"

RADIO REMOVAL:

1.  2.  3.  4. 

2000-05 Buick LeSabre 2000-05 Buck Park Avenue

Extract (2) screws from below heater controls. Remove ashtray. Extract (2) screws from ashtray cavity. Pull radio trim bezel out from dash and unscrew cigarette lighter collar from the back side. Unplug the cigarette lighter 12V positive wire. Remove radio trim bezel. Extract the (4) screws securing the radio, unplug the radio and unplug all connectors and remove.

6

1.  2.  3.  4.  5. 

Open center console lid and extract (2) screws from front of console. Remove rubber pads from cup holders and from storage pocket and extract (4) screws. Carefully lift up and out and on center panel, unsnap and remove. Extract (2) screws from bottom of radio/climate control bezel, unsnap and remove. Extract (3) 9/32" screws securing radio, disconnect and remove.

1996-99 Buick Riviera

SEE ILLUSTRATION "A"

Radio Removal:

1.  Gently pull outward on Left and Right windshield pillar panels to release (2) snap clips and extract each one. 2.  Unsnap side dash panels and remove (1) 7 MM screw from behind each. 3.  Extract (6) plastic push-pin fasteners from under front edge of upper dash pad. Pull outward to remove the bottom panel of the upper dash pad. 4.  Extract (5) 7-MM screws securing upper dash pad, lift up and outward to remove pad. 5.  Carefully pull outward on dash/instrument bezel to release clips, unplug and remove bezel. 6.  Extract (3) 7-MM screws from climate control module, unplug and remove module. 7.  Extract (4) 7-MM screws securing radio, unplug connectors, antenna lead, and remove radio.

3

1995-96 Buick Roadmaster 

2004-Up Chevrolet Colorado 2004-Up GMC Canyon

SEE ILLUSTRATION "A"

RADIO REMOVAL:

1.  2.  3.  4.  5.  6. 

Remove side dash panels by carefully pulling outward on them to release fastening clips. Carefully pull out on underdash panel below steering column to release fastening clips, and remove panel. Carefully pull outward on lower panel at right of glove box to release fastening clips, and remove panel. Extract (2) 7 MM screws above instrument cluster. Make sure the parking brake is on, then insert the key and turn to the "on" position. Put the vehicle into first or low gear, and tilt the steering column adjustment all the way down and pull outward on the complete instrument panel around gauges and along top of glovebox. Panel clips will release and dash panel can be removed. 7.  Extract (3) 7 MM screws holding radio, unplug connector, antenna cable and remove radio.

1996-98 Buick Skylark  1996-98 Oldsmobile Achieva

RADIO REMOVAL:

1.  Unsnap dash bezel, lift away, disconnect and remove. 2.  Unscrew (3) Hex bolts securing radio, lift away, unplug and remove.

2001-02 Chevrolet Express 2001-02 GMC Savana

SEE ILLUSTRATION "A"

RADIO REMOVAL:

1.  Carefully pry out on dash bezel to release, unplug and remove. 2.  Remove three (3) 7MM hex screws holding radio, unplug and remove.

SEE ILLUSTRATION "A"

RADIO REMOVAL:

1.  2.  3.  4.  5.  6.  7.  8. 

SEE ILLUSTRATION "B"

Twist and release fasteners holding drivers and passengers under dash covers, and remove. Open glove box, push stopper tabs inward, open all the way down, and remove glove box. Extract (6) 9/32" Hex screws from glove box area. Extract (2) 9/32" Hex screws from plastic tube in glove box area and extract (2) from just below plastic tube. Extract (2) 9/32" Hex screws from driver's side bottom dash. Open and remove fuse panel access door. Carefully grasp complete dash/radio bezel, pull out to release clips and remove. Extract (3) screws holding radio in, unplug connector and remove.

2003-Up Chevrolet Express 2003-Up GMC Savana

SEE ILLUSTRATION "B"

RADIO REMOVAL:

1.  2.  3.  4.  5. 

Extract (2) 10mm bolts from below steering column panel and remove. Extract (2) 10mm bolts from below passenger dash panel and remove. Extract (2) 10mm bolts located inside center dash pocket. Carefully pull outward on dash/instrucment bezel to release clips and remove. Extract (3) 9/32" screws holding radio, unplug and remove.

2000-05 Chevrolet Impala

SEE ILLUSTRATION "B"

RADIO REMOVAL: SEE ILLUSTRATION "B" 2003-06 Cadillac Escalade 2003-06 Cadillac Escalade ESV 2003-06 Cadillac Escalade EXT 2003-06 Chevrolet Avalanche 2003-06 Chevrolet Silverado 2007-Up Chevrolet Silverado Classic

2003-06 Chevrolet Suburban 2003-06 Chevrolet Tahoe 2003-06 GMC Sierra 2007-Up GMC Sierra Classic 2003-06 GMC Yukon 2003-06 GMC Yukon XL

RADIO REMOVAL:

2002-04 GMC Jimmy 2002-04 GMC Sonoma

SEE ILLUSTRATION "A"

RADIO REMOVAL:

SEE ILLUSTRATION "B"

RADIO REMOVAL:

1.  Extract (2) screws securing the top area of the driver's side underdash cover panel. 2.  Pull the driver's side underdash down to access and extract (2) 7mm hex screws holding the bottom of the dash bezel. 3.  Extract the screw located in the top edge of the dash panel at the instrument cluster. 4.  Carefully pry out on the dash bezel to release the fastening clips securing the bezel to the dash and unplug headlight/miscellaneous switches on the driver's left of the bezel.

2000-05 Chevrolet Cavalier 2000-05 Pontiac Sunfire

Extract (2) 9/32" hex screws from above instrument panel. Remove fuse panel cover and extract (1) 9/32" hex screw from behind. Remove passenger side fuse cover and extract (1) 9/32" screw from behind. Drop underdash covering using panel removal tool and extract (2) 9/32" screws from behind. Remove (1) 9/32" screw from left side trim, tilt wheel down, and pull away dash bezel, disconnect and remove. Remove (3) 9/32" screws securing the radio, disconnect and remove from dash.

2001-03 Chevrolet Malibu 2004 Chevrolet Classic

1.  Turn ignition on and shift vehicle into first gear. 2.  Unsnap trim bezel by pulling firmly. 3.  Using a 7mm socket, remove 3 bolts from radio, disconnect, and remove.

2002-04 Chevrolet Blazer 2004 Chevrolet S-10 P/U 1998-01 Oldsmobile Bravada

1.  2.  3.  4.  5.  6. 

1.  Use a small flat blade or pick to remove ignition switch collar. 2.  Using panel removal tool, pry out dash bezel, disconnect and remove. 3.  Remove three (3) 7MM screws securing radio, disconnect and remove.

1998-01 Chevrolet Metro 1995-97 Geo Metro

SEE ILLUSTRATION "C"

RADIO REMOVAL:

1.  2.  3.  4.  5.  6. 

Extract (2) screws from below heater controls. Remove ashtray. Extract (2) screws from ashtray cavity. Pull radio trim bezel out from dash and unscrew cigarette lighter collar from the back side. Unplug the cigarette lighter 12V positive wire. Remove radio trim bezel. Extract the (4) screws securing the radio, unplug all connectors and remove.

SEE ILLUSTRATION "B"

2000-05 Chevrolet Monte Carlo

RADIO REMOVAL:

RADIO REMOVAL:

1.  2.  3.  4.  5. 

1.  2.  3.  4.  5. 

Open glove box and remove (5) 9/32" screws. Remove side panels from drivers side dash and passengers side dash, and extract (1) 9/32" screw from each side. Remove 1 Phillips head screw at top center of air vent. Extract 2 screws under vent panel, carefully remove top of dash. Extract 3 screws from the top of the front dash panel, disconnect and remove.

4

SEE ILLUSTRATION "B"

Extract (1) Phillips head screw from glove box. Remove cylinder cover from around ignition keyhole. Extract (2) Phillips head screw from beneath steering column plate, and remove cover. Remove fuse access cover and remove (1) Phillips head screw from behind. Adjust steering wheel column down and remove dash trim bezel. Disconnect hazard switch and remove panel.

5