Hair Care Formulary pure in cosmetics - Essential Ingredients, Inc

417 downloads 886 Views 135KB Size Report
Hair Care. Formulary. April, 2008 pure in cosmetics .... Perfume. 0.2. Paratexin FPX (Phenoxyethanol and Methylparaben and Ethylparaben and Propylparaben  ...
Hair Care Formulary April, 2008

pure in cosmetics

Contents SHAMPOOS........................................................................................................................................ 3 Anti-Dandruff Shampoo with BENTONE® MA ............................................................................ 3 2 in 1 Conditioning Shampoo with BENTONE® EW ................................................................... 4 Hair Shampoo with BENTONE® EW........................................................................................... 5 Pearlised Shampoo with THIXCIN® R ........................................................................................ 6 CONDITIONERS ................................................................................................................................. 7 Creamy Rinse Conditioner with BENTONE GEL® PTIS V.......................................................... 7 STYLING AND TREATMENTS........................................................................................................... 8 Ethnic Hair Moisturising Cream with BENTONE GEL® MIO V and BENTONE® EW.................. 8 Glossifying Hair Pomade with BENTONE GEL® MIO V ............................................................. 9 Hair Defining Complex with BENTONE GEL® VS-5PC V......................................................... 10 Hair Dressing Cream with THIXCIN® R and BENTONE GEL® GTCC V .................................. 11 Hair Pomade with BENTONE GEL® PTIS V............................................................................. 12 Hair Pomade with BENTONE GEL® MIO V, BENTONE GEL® VS5-PC V and THIXCIN® R.... 13 Hair Relaxer Cream with BENTONE GEL® MIO V ................................................................... 14 Hair and Scalp Grease with THIXCIN® R and BENTONE GEL® LOI V .................................... 15 Hair Styling Clay with BENTONE GEL® VS-5PC V .................................................................. 16 Hair Styling Stick with THIXCIN® R........................................................................................... 17 Spiky Hair Clay with THIXCIN® R and BENTONE GEL® CAO V.............................................. 18 2

SHAMPOOS Anti-Dandruff Shampoo with BENTONE® MA BY3031/13 Advantages The presence of BENTONE® MA, rheological additive in this system: •

Imparts viscosity



Helps suspend the Zinc Pyrithione



Produces a stable emulsion at increased temperatures

Ingredient PHASE A BENTONE® MA (Hectorite) Methocel E15 (Hydroxypropyl Methylcellulose) Deionised Water Tegosoft TN (C12-15 Alkyl Benzoate) Tego Alkanol 1618 (Cetearyl Alcohol) Paratexin P (Propyl Paraben) PHASE B Zinc Omadine 48% Aq. Dispersion (Zinc Pyrithione) PHASE C SERDET® DFK 30 (Sodium Lauryl Sulfate) Tego Betaine F50 (Cocamidopropyl Betaine) Tego Pearl N 100 (Glycol Distearate and Steareth-4) Monamid CMA (Cocamide MEA) PHASE D Lanodant DM (DMDM Hydantoin) Rain Fresh (Fragrance) FD & C Green #3 (0.1% Solution) (Green 3) Citric Acid (50% Solution)

Supplier

% w/w

ELEMENTIS Specialties Dow Chemical Evonik Degussa Evonik Degussa S. Black Group

1.5 0.25 52.9 4.0 1.2 0.1

Arch Personal Care

2.0

ELEMENTIS Specialties Evonik Degussa Evonik Degussa Uniqema

30.0 7.0 3.0 2.5

RITA Bell Flavors & Fragrances

0.5 0.1 0.25 To pH 5.5 – 6.0

Mixing Procedure

1. Predisperse Phase A with high shear and mix for at least 20 minutes until uniform. 2. Disperse Phase B in Phase A with high shear and mix until uniform. 3. Add Phase C ingredients in the order given, using lower shear mixing. 4. Add Phase D ingredients in the order given, using lower shear mixing until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

3

2 in 1 Conditioning Shampoo with BENTONE® EW BY3130/31 Advantages The presence of BENTONE® EW, rheological additive in this system: •

Imparts viscosity



Produces a creamier textured foam



Reduces static



Produces a stable system at increased temperatures



Improves storage stability



Leaves hair feeling soft and glossy

Ingredient PHASE A BENTONE® EW (Hectorite) Deionised Water PHASE B Mackadet EQ-178 (Decyl Glucoside and Cocamidopropyl Hydroxysultaine and Cocamidopropyl Betaine and Cocamide MIPA and Disodium Laureth Sulfosuccinate and Disodium Lauryl Sulfosuccinate) Propylene Glycol PHASE C Dow Corning 1664 Emulsion (Dimethicone and Laureth-4 and Laureth-23) Vegetable Glycerin Crillet 3 Super (Polysorbate 60) PHASE D Germaben II (Propylene Glycol and Diazolidinyl Urea and Methylparaben and Propylparaben) Rain Fresh (Fragrance) FD&C Green #3 (0.1% Solution) (Green 3) Citric acid (50% solution)

Supplier

% w/w

ELEMENTIS Specialties

1.5 48.5

Mcintyre Group LTD

45.6

Dow Chemical Company

1.0

Dow Corning

3.0

Croda

8.0 3.3

ISP

0.2

Bell Flavors & Fragrances

0.1 0.1 q.s.

Adjust PH: 5.5-6.5

Mixing Procedure

1. Disperse Phase A with high shear and mix for at least 20 minutes until uniform. 2. Add Phase B, mixing well, but without causing foamimg. 3. Add Phase C to Phase A+B with low shear mixing until uniform. 4. Add Phase D one at a time with gentle mixing until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

4

Hair Shampoo with BENTONE® EW RECF-147 Advantages The presence of BENTONE® EW, rheological additive in this system: •

Produces a creamier textured foam



Leaves wet hair feeling slightly conditioned



Reduces the static problem



Provides thermostable viscosity control



Gives softer hair feeling and gloss

Ingredient PHASE A BENTONE® EW (Hectorite) Deionised Water PHASE B SERDET® DFK 30 (Sodium Lauryl Sulfate) Tego Betain F50 (Cocamidopropyl Betaine) Plantacare 818 UP (Coco Glucoside) PHASE C Tego Pearl N100 (Glycol Distearate and Steareth 4) Abil B8832 (Dimethicone Copolyol) PHASE D Genapol L3 (Laureth-3) D-Panthenol 75 W (Panthenol) Perfume Paratexin FPX (Phenoxyethanol and Methylparaben and Ethylparaben and Propylparaben and Butylparaben and Isobutylparaben) PHASE E Purac PH90 (Lactic Acid)

Supplier

% w/w

ELEMENTIS Specialties

1.5 51.9

ELEMENTIS Specialties Evonik Degussa Cognis

28.0 6.0 6.0

Evonik Degussa Evonik Degussa

3.0 0.2

Clariant Roche

2.0 1.0 0.2 0.2

S. Black Group

Purac

pH5.5-6.0

Mixing Procedure

1. Disperse Phase A using Silverson homogenising and continue to mix for 15 - 20 minutes. 2. Using a propeller stirrer, add Phase B. 3. With continued propeller stirring add Phase C. 4. Add Phase C with propeller stirring. 5. Adjust the pH if required with Phase E.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

5

Pearlised Shampoo with THIXCIN® R HPA17/18/9 Advantages The presence of THIXCIN® R, rheological additive in this system: •

Improves application and dispensability



Provides pearl stabilisation and overall improved stability



Enhances final shampoo appearance

Ingredient PHASE A Deionised Water Antil 120 (PEG-120 Methyl Glucose Dioleate) PHASE B SERDET® DFK 30 (Sodium Lauryl Sulfate) Tego Betain F50 (Cocamidopropyl Betaine) Genapol PDB (Glycol Distearate and Laureth-4 and Cocamidopropyl Betaine) PHASE C Tegosoft GC (PEG-7 Glyceryl Cocoate) Jojoba Oil PHASE D THIXCIN® R PHASE E Propylene Glycol Paratexin FPX (Phenoxyethanol and Methylparaben and Ethylparaben and Propylparaben and Butylparaben and Isobutylparaben)

Supplier

% w/w

Evonik Degussa

39.1 0.75

ELEMENTIS Specialties Evonik Degussa Clariant

39.3 13.3 3.0

Evonik Degussa S. Black

2.0 0.5

ELEMENTIS Specialties

0.1

S. Black Group

1.75 0.2

Mixing Procedure

1. Warm Phase A slightly to melt. 2. Add Phase B with propeller stirring. 3. Mix Phase C. Heat to 60°C. 4. Add Phase D and mix using a silverson homogeniser for 15 minutes. 5. Add Phase C+D to Phase A+B with propeller stirring. 6. Add Phase E to Phase A+B+C+D and mix.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

6

CONDITIONERS Creamy Rinse Conditioner with BENTONE GEL® PTIS V BY3031/39 Advantages The presence of BENTONE GEL® PTIS V, rheological additive in this system: •

Produces a stable system at increased temperatures



Improves storage stability

Ingredient PHASE A BENTONE GEL® PTIS V (Pentaerythrityl Tetraisostearate and Disteadimonium Hectorite and Propylene Carbonate) Incroquat Behenyl TMS (Behentrimonium Methosulfate and Cetearyl Alcohol) Cropure Olive (Olea Europaea (Olive) Fruit Oil) Dow Corning Q2-8220 Conditioning Additive (Trimethylsilylamodimethicone) Tego Alkanol 16 (Cetyl Alcohol) PHASE B Deionised Water Varisoft 432 CG (Dicetyldimonium Chloride) Glycerine Incromectant AQ (Acetamidopropyl Trimonium Chloride) PHASE C Hydrotriticum 2000 (Hydrolyzed Wheat Protein) Germaben II E (Propylene Glycol and Diazolidinyl Urea and Methylparaben and Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties

3.0

Croda

3.5

Croda Dow Corning

3.0 2.0

Evonik Degussa

1.0

Evonik Degussa RITA Croda

80.5 2.0 2.0 1.0

Croda ISP

1.0 0.5

Mixing Procedure

1. Mix Phase A and heat to 75-80°C. 2. In a separate container combine Phase B and heat to 75-85°C. 3. Add Phase A to Phase B with high agitation. 4. Cool to 45°C and add Phase C with low agitation until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

7

STYLING AND TREATMENTS Ethnic Hair Moisturising Cream with BENTONE GEL® MIO V and BENTONE® EW BY3031/40 Advantages The presence of BENTONE GEL® MIO V and BENTONE® EW, rheological additives in this system: •

Creates a light-feel and reduces tackiness



Gives body, and allows easy spreading, due to the increased thixotropic nature



Produces a stable system at increased temperatures



Improves storage stability

Ingredient PHASE A BENTONE® EW (3% Dispersion) (Hectorite) Deionised Water Ritapan D (D-Panthenol) PHASE B BENTONE GEL® MIO V (Mineral Oil and Disteardimonium Hectorite and Propylene Carbonate) Drakeol 7 (Mineral Oil) Arlacel 165 (Glyceryl Stearate and PEG-100 Stearate) Lanette O Wax (Cetearyl Alcohol) PHASE C SERDET® DFK 30 (Sodium Lauryl Sulfate) Tego Betaine F50 (Cocamidopropyl Betaine) Tego Pearl N 100 (Glycol Distearate and Steareth-4) Monamid CMA (Cocamide MEA) PHASE D Vitamin E (Tocopherol) Germaben II E (Propylene Glycol and Diazolidinyl Urea and Methyparaben and Propylparaben) Aloe Vera 1:1 (Aloe Barbadensis Leaf Extract)

Supplier ELEMENTIS Specialties

% w/w

RITA

33.5 25.5 1.0

ELEMENTIS Specialties

39.0

Penreco Uniqema Cognis

25.0 6.0 3.0

ELEMENTIS Specialties Evonik Degussa Evonik Degussa Uniqema

30.0 7.0 3.0 2.5

BASF ISP

0.5 0.5

Caribbean Aloe Vera

0.2

Mixing Procedure

1. Predisperse Phase A and heat to 70 - 75 °C. 2. Disperse Phase B and heat to 75 - 80 °C. 3. Add Phase B into Phase A using a homogeniser for 15-20 minutes.

4. Cool to 45 °C and add Phase C in the order listed. Mix well until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

8

Glossifying Hair Pomade with BENTONE GEL® MIO V BY2968/74 Advantages The presence of BENTONE GEL® MIO V, rheological additive in this system: •

Creates a non-greasy glossing pomade, which can create incredible styles



Gives body and allows easy spreading, due to the increased thixotropic nature



Produces a stable system at increased temperatures



Improves storage stability

Ingredient PHASE A BENTONE GEL® MIO V (Mineral Oil and Disteardimonium Hectorite and Propylene Carbonate) Drakeol 7 (Mineral Oil) PHASE B Polychol 15 (Laneth-15) Crill 45 (Sorbitan Trioleate) Crill 4 (Sorbitan Oleate) PHASE C Deionised Water Propylene Glycol PHASE D Germaben II E (Propylene Glycol and Diazolidinyl Urea and Methylparaben and Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties

3.0

Penreco

22.0

Croda Croda Croda

24.0 3.5 1.0

Dow Corning

34.0 12.0

ISP

0.5

Mixing Procedure

1. Disperse Phase A and heat to 75 - 80 °C. 2. In a separate container combine Phase B and heat to 75 - 85 °C. 3. Add Phase B to Phase A with adequate agitation. 4. Premix Phase C and heat to 70 - 75 °C. 5. Add Phase C to the mixture with high shear mixing until uniform. 6. Add Phase D to the mixture at 70 °C and mix till uniform. 7. Hot pour into the jar at 70 °C.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

9

Hair Defining Complex with BENTONE GEL® VS-5PC V KB5/050 Advantages The presence of BENTONE GEL® VS-5PC V, rheological additive in this system: •

Improved emulsion stability



Enriches the formulation



Imparts viscosity and body



Provides ease of application and spreadability



Speeds adsoprtion onto the hair



Enhances overall hair appearance and eliminates stickiness



Smoothes the hair cuticle to provide a soft feel, with a combination of good curl definition and style management

Ingredient PHASE A BENTONE GEL® VS-5PC V (Cyclopentasiloxane and Disteardimonium Hectorite and Propylene Carbonate) Incroquat Behenyl TMS (Cetearyl Alcohol and Behentrimonium Methosulphate) PHASE B Deionised Water Glycerine Luviskol VA64 Powder (VP/VA Copolymer) PHASE C Dow Corning 345 Fluid (Cyclomethicone) PHASE D Propylene Glycol Paratexin FPX (Phenoxyethanol and Methylparaben and Ethylparaben and Propylparaben and Butylparaben and Isobutylparaben) PHASE E Germaben II E (Propylene Glycol and Diazolidinyl Urea and Methylparaben and Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties

1.0

Croda Chemicals

4.0

BASF

78.4 4.0 2.0

Dow Corning

10.0

Dow Corning S. Black Group

12.0 0.2

ISP

0.5

Mixing Procedure

1. Heat Phase A to 75-80°C. 2. In a separate vessel heat Phase B to 75-80°C. 3. Add Phase A to Phase B with silverson homogenising and mix for 20 minutes. 4. With propeller stirring add Phase C. 5. Mixing on the propeller stirrer, cool the product to 35°C. 6. Below 35°C add Phase D with stirring. 7. Measure the pH and if needed adjust to pH5.5. © Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

10

Hair Dressing Cream with THIXCIN® R and BENTONE GEL® GTCC V BY3130/74 Advantages The presence of THIXCIN® R and BENTONE GEL® GTCC V, rheological additives in this system: •

Create hair definition and style without contributing to hair stiffness, keeping the hair looking sleek and frizz free



Leave hair feeling soft and smooth, with a glossy shine



Produce a stable emulsion at increased temperatures



Improve storage stability

Ingredient PHASE A BENTONE GEL® GTCC V (Caprylic/Capric Triglyceride and Stearalkonium Hectorite and Propylene Carbonate) THIXCIN® R (Trihydroxystearin) Abil OSW 5 (Cyclopentasiloxane and Dimethiconol) Dow Corning 245 Fluid (Cyclopentasiloxane) Abil EM 90 (Cetyl PEG/PPG-10/1 Dimethicone) Drakeol 34 (Mineral Oil) Abil Soft AF 100 (Methoxy PEG/PPG-7/3 Aminopropyl Dimethicone) PHASE B Deionised Water Sodium Chloride PHASE C Deionised Water Propylene Glycol PHASE D Germaben II E (Propylene Glycol and Diazolidinyl Urea and Methylparaben and Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties

4.0

ELEMENTIS Specialties Evonik Degussa Dow Corning Evonik Degussa Penreco Evonik Degussa

0.5 8.0 6.0 2.5 2.0 0.5

75.5 0.5

Dow Corning

34.0 12.0

ISP

0.5

Mixing Procedure

1. Combine Phase A and heat to 60 - 70 °C. 2. In a separate container premix Phase B and heat to 60 - 70 °C. 3. Slowly add Phase B to Phase A with shear for 10 minutes. 4. Homogenize at 65 °C for 10 minutes. 5. Cool down to 45 °C and add Phase C.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

11

Hair Pomade with BENTONE GEL® PTIS V KR9/092 Advantages The presence of BENTONE GEL® PTIS V, rheological additive in this system: •

Helps provide an emollient film, which leaves the hair with a better shine



Aides wet and dry combability



Leaves the hair softer



Increases viscosity and enhanced stability

Ingredient PHASE A BENTONE GEL® PTIS V (Pentaerythrityl Tetraisostearate and Disteardimonium Hectorite and Propylene Carbonate) Tego Alkanol 1618 (Cetearyl Alcohol) Mineral Oil Tegosoft Liquid (Cetearyl Ethylhexanoate) Beeswax Tegin 4100 Pellets (Glyceryl Stearate) Arlacel 987 (Sorbitan Isostearate) PHASE B Dow Corning 345 Fluid (Cyclomethicone)

Supplier

% w/w

ELEMENTIS Specialties

6.0

Evonik Degussa

Evonik Degussa Uniqema

11.0 7.0 6.0 5.0 4.0 4.0

Dow Corning

57.0

Evonik Degussa

Mixing Procedure

1. Combine Phase A and heat to 110°C with mixing. 2. Cool with mixing to 70°C. 3. Add Phase B to main batch, with mixing. 4. Cool with mixing.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

12

Hair Pomade with BENTONE GEL® MIO V, BENTONE GEL® VS5-PC V and THIXCIN® R BY3130/61 Advantages The presence of BENTONE GEL® MIO V, BENTONE GEL® VS5-PC V and THIXCIN® R, rheological additives in this system: •

Create lift easily, due to the unique texture, leaving the hair feeling soft and smooth, with a glossy shine



Produce a stable pomade at increased temperatures



Improve storage stability

Ingredient PHASE A THIXCIN® R (Trihydroxystearin) Drakeol 7 (Mineral Oil) PHASE B BENTONE GEL® MIO V (Mineral Oil and Disteardimonium Hectorite and Propylene Carbonate) BENTONE GEL® VS-5PC V (Cyclopentasiloxane and Disteardimonium Hectorite and Propylene Carbonate) Cropure Avocado (Persea Gratissima (Avocado) Oil) Dow Corning 345 Fluid (Cyclomethicone) Vitamin E Acetate (Tocopheryl Acetate) PHASE C Unisept P (Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties Penreco

2.0 47.5

ELEMENTIS Specialties

30.0

ELEMENTIS Specialties

10.0

Croda Dow Corning BASF

5.0 5.0 0.3

Universal Preserv-A-Chem

0.2

Mixing Procedure

1. Disperse Phase A with higher shear at 55 - 60 °C for 15-20 minutes. 2. In a separate container combine Phase B and mix until uniform. 3. Add Phase B to Part A with adequate agitation. 4. Cool down to 60 °C and add Phase C with slow shear until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

13

Hair Relaxer Cream with BENTONE GEL® MIO V BY3130/36 Advantages The presence of BENTONE GEL® MIO V, rheological additive in this system: •

Gives body and allows easy spreading, due to the increased thixotropic nature



Promotes even distribution



Produces a stable system at increased temperatures



Improves storage stability

Ingredient PHASE A BENTONE GEL® MIO V (Mineral Oil and Disteardimonium Hectorite and Propylene Carbonate) Carnation (Mineral Oil) Snow White Petrolatum (Petrolatum) PHASE B Polawax NF (Emulsifying Wax) Volpo S10 (Steareth-10) Crodafos N10N (DEA-Oleth-10 Phosphate) Lanette O Wax (Cetearyl Alcohol) PHASE C Deionised Water Propylene Glycol PHASE D NaOH 25% Solution Germaben II E (Propylene Glycol and Diazolidinyl Urea and Methylparaben and Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties

5.0

Crompton UPI

10.0 10.0

Croda Croda Croda Cognis

8.0 2.5 2.0 1.5

Dow Corning

ISP

51.7.0 2.0 6.8 0.5

Mixing Procedure

1. Disperse Phase A and heat to 75 – 80 °C. 2. In a separate container combine Phase B and heat to 75 - 85 °C. 3. Add Phase B to Phase A with adequate agitation. 4. Premix Phase C and heat to 70 - 75 °C. 5. Add Phase C to the mixture with homogenizing. 6. Add Phase D, in the order given, to the mixture when temperature reaches 45 °C and mix well with low shear.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

14

Hair and Scalp Grease with THIXCIN® R and BENTONE GEL® LOI V BY3130/71 Advantages The presence of THIXCIN® R and BENTONE GEL® LOI V rheological additives in this system: •

Create a light-feel and allow easy spreading, due to the increased thixotropic nature



Produce a stable system at increased temperatures



Improve storage stability

Ingredient PHASE A BENTONE GEL® LOI V (Lanolin Oil and Isopropyl Palmitate and Stearalkonium Hectorite and Propylene Carbonate) Drakeol 7 (Mineral Oil) PHASE B THIXCIN® R (Trihydroxystearin) PHASE C Beeswax White SP 422 (Beeswax) Penreco Snow (Petrolatum) Lanette O Wax (Cetearyl Alcohol) PHASE D Unisept P (Propylparaben) Fragrance

Supplier

% w/w

ELEMENTIS Specialties

20.0

Penreco

30.0

ELEMENTIS Specialties

2.0

Strahl & Pitsch Penreco Cognis

10.0 34.0 3.5

Universal Preserv-A-Chem International Flavors & Fragrances

0.4 0.1

Mixing Procedure

1. Heat Phase A to 55 - 60 °C and mix. 2. Add Phase B to Phase A and mix with high shear for 15 minutes. 3. In a separate container combine Phase C and heat to 75 - 85 °C and mix until uniform. 4. Add Phase A+B to Phase C with adequate agitation. 5. Cool down to 60 °C, and add Phase C with slow shear, mixing until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

15

Hair Styling Clay with BENTONE GEL® VS-5PC V Florotech KR7/028 Advantages The presence of BENTONE GEL® VS-5PC V, rheological additive in this system: •

Improved stability, viscosity and body

Ingredient PHASE A BENTONE GEL® VS-5PC V (Cyclopentasiloxane and Disteardimonium Hectorite and Propylene Carbonate) Penreco Snow (Petrolatum) Floresters 15 (Jojoba Esters) Beeswax White Refined SP 44 (Beeswax) S & P Carnauba Wax Refined (Copernica Cerifera Wax) Florasun 90 (Helianthus Annuus Seed Oil) Floresters 20 (Jojoba Esters) Altalc 200 USP (Talc) PHASE B Deionised Water Florasolve PEG-150 Hydrogenated Jojoba (PEG-150 Jojoba Hydrogenated) Paratexin M (Methylparaben) PHASE C Tocopherol

Supplier ELEMENTIS Specialties

% w/w 5.0

Penreco Floratech Strahl & Pitsch Strahl & Pitsch Floratech Floratech Luzenac

28.50 7.0 6.0 6.0 5.0 3.0 2.0

Floratech

26.3 10.0

S. Black Group

0.2

Cognis

1.0

Mixing Procedure

1. Combine Phase A and heat to 90 °C with propeller agitation. Mix for 20 minutes. 2. Combine Phase B and mix at 80 °C with propeller agitation. 3. Slowly add Phase A to Phase B with fast propeller agitation. 4. Cool to 75 °C and add Phase C. 5. Pour into a container and allow to cool to room temperature.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

16

Hair Styling Stick with THIXCIN® R BY3130/14 Advantages The presence of THIXCIN® R, rheological additive in this system: •

Builds viscosity by acting as a stiffening agent



Produces a stable system at increased temperatures



Improves pay off, adds lubricity and gives a buttery feel

Ingredient PHASE A THIXCIN® R (Trihydroxystearin) Unicast-CO (Ricinus Communis (Castor) Seed Oil) PHASE B Penreco Snow (Petrolatum) Beeswax White SP 422 (Beeswax) Shebu (Butyrospermum Parkii (Shea Butter)) Candelilla Wax SP 37 (Euphorbia Cerifera (Candelilla) Wax) Carnauba Wax SP 63 (Copernicia Cerifera (Carnauba) Wax) PHASE C Unisept P (Propylparaben) Fragrance

Supplier

% w/w

ELEMENTIS Specialties Universal Preserv-A-Chem

8.0 54.7

Penreco Strahl & Pitsch RITA Strahl & Pitsch Strahl & Pitsch

15.0 10.0 6.0 4.0 2.0

Universal Preserv-A-Chem International Flavors & Fragrances

0.2 0.1

Mixing Procedure

1. Combine Phase A at 55-60 °C with high shear for 15-20 minutes. 2. In a separate container combine Phase B and heat to 75 – 85 °C until uniform. 3. Add Phase B to Phase A with adequate agitation. 4. Cool down to 60 °C, and add Phase C with slow shear until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

17

Spiky Hair Clay with THIXCIN® R and BENTONE GEL® CAO V BY3130/69 Advantages The presence of THIXCIN® R and BENTONE GEL® CAO V, rheological additives in this system: •

Provide a high degree of hold for a longer time, for gravity defying styles



Allow easy spreading, due to the increased thixotropic nature



Produce a stable system at increased temperatures



Improve storage stability

Ingredient PHASE A THIXCIN® R (Trihydroxystearin) Unicast-CO (Ricinus Communis (Castor) Seed Oil) PHASE B BENTONE GEL® CAO V (Ricinus Communis and Stearalkonium Hectorite and Propylene Carbonate) Carnation (Mineral Oil) Beeswax White SP 422 (Beeswax) Parvan 127 (Paraffin) Penreco Snow (Petrolatum) Carnauba Wax SP 63 (Copernicia Cerifera (Carnauba) Wax) Tagat CH 40 (PEG-40 Hydrogenated Castor Oil) PHASE C Unisept P (Propylparaben)

Supplier

% w/w

ELEMENTIS Specialties Universal Preserv-A-Chem

2.0 29.0

ELEMENTIS Specialties

18.0

Crompton Strahl & Pitsch Exxon Penreco Strahl & Pitsch Evonik Degussa

15.0 10.0 8.0 8.0 6.0 3.5

Universal Preserv-A-Chem

0.5

Mixing Procedure

1. Combine Phase A at 55-60 °C with high shear for 15 - 20 minutes. 2. In a separate container combine Phase B and heat to 75 - 85 °C, and mix until uniform. 3. Add Phase B to Phase A with adequate agitation. 4. Cool down to 60 °C, and add Phase C with slow shear. Mix until uniform.

© Copyright 2008, Elementis Specialties, Inc. All rights reserved. Copying and/or downloading of this document or information therein for republication is not allowed unless prior written agreement is obtained from Elementis Specialties, Inc. ® Registered trademark of Elementis Specialties, Inc. The information in this publication is, to the best of our knowledge, true and accurate, but since the conditions of use are beyond our control, no warranty is given or to be implied in respect of such information. In every case, caution must be exercised to avoid violation or infringement of statutory obligations and any rights belonging to a third party. We are, at all time, willing to study customers’ specific outlets involving our products in order to enable their most effective use.

18