Industrial Ethernet - CTC Union

Rackmount Switch 4G LTE Router/Gateway SyncE Switch/PoE Switch

w w w.c t c u.c o m

FieldBus to Fiber Converter EN 50155 Switch IEC 61850-3 Switch

Industrial Ethernet

Product Guide

EN50155

NEMA TS2

EN50121-4

EN61000-6-2 EN61000-6-4

e-Catalog

R

Industrial Product Category EN 50155 Switch Series PoE Series

SyncE Switch

IEC 61850-3

Ethernet Switch

Management Software SmartView

FieldBus to Fiber Converter

TM

Rackmount Switch Series • 1GbE/10GbE product portfolio • 24+4, 24+8, modular solutions • Up to 24 IEEE802.3at PoE ports • Up to 28 SFP GbE fiber ports • Supports 14 μ-Ring instance in one switch • Network recovery time in / under 10ms

Product Selection Table

Reliable Industrial Ethernet Products

• Ultra PoE++ 60W solution • 4KV surge & 2.25KV Hi-pot isolation protection • LAN extend up to 1.2Km with PoE power feeding • 24VDC power booster and regulate power output • Product range of switch, converter, extender and injector

• EN 50155 certified • IEC 61375 TTDP • Auto-bypass for failover • Power input range 24 to 110VDC • IEEE 802.3at PoE 8/12/16-port product portfolio • M12 connector, IP65/IP67 rugged design

Industrial Product Category

www.ctcu.com

Industrial Product Series

2018 Industrial Product Guide

4G LTE Series • 2 SIM slot for failover redundancy • GNSS: GPS/GLONASS/Galileo • LAN, DI/DO, RS-232/485 serial interface • IPsec VPN/Modbus RTU/TCP, Real-COM • IEEE802.11b/g/n/ac • Routing: RIP1/RIP2, OSPF, VRRP

R

1

www.ctcu.com


2

R


Industrial Product Series Negative Voltage

Rackmount Switches

µ-Ring

IEEE 1588 V2

Related Products ICS-G24044X / ICS-G24S4X / ICS-M2404X IGS-2408SM / IGS-M2404S IPS-M2404S

Please check page 14 for more details.

• 10G backbone for high bandwidth transmission • Each 10G switch support 14 ring for centralization • Full Gigabit 24+4, 24+8 and modular solutions • Up to 24 IEEE802.3at PoE ports

• Up to 28 SFP GbE fiber ports • Power station IEC 61850-3 certified • Dual and wide range power input for power failure redundancy

10G Backbone with µ-Ring Technology Up to 14 rings

10G Core Switch

10G Core Switch

10G Backbone

10G

10G

10G Core Switch

10G Core Switch

Up to 14 rings

SyncE Switches

Negative Voltage

E IEEE 1588 V2

µ-Ring

SyncE

Related Products IGS-1608SM-SE / IGS-804SM-SE


• Supports Sync. Ethernet allow operators to deliver service with optimal stability and continuity in end-to-end connectivity • Supports IEEE1588 PTP V2 for precise time synchronization to operate in Ordinary-Boundary, Peer to Peer Transparent Clock, End to End Transparent Clock, Master, Slave mode by each port

• Supports negative voltage power input • 2.25K VDC Hi-pot isolation protection for Ethernet ports and power • 4KV surge protection for UTP and Fiber ports

Mobile Backhaul Application

SyncE

Base Station

Primary Reference Clock (PRC)

IGS-1608SM-SE IGS-804SM-SE

4G LTE

SyncE

GbE 4G LTE

Backbone Network

3

www.ctcu.com


www.ctcu.com

X

Code

EN50155

IP64/67

µ-Ring


• Wide range products of 5, 8+2,12+4, 22+4 Ethernet port available • IEEE802.3af/at PoE 8, 12, 16-port for PD connection • Fast Ethernet M12 D-code, Gigabit M12 X-code • Supports 2 copper bypass for failover pass-through • Certificated EN50155, EN50121-4, IEC 61375-2-3/5 TTDP, EN45545-2 • IP64/67 rugged metal housing design Supports 24~110VDC Power Input

Smart Train Modern transportation systems for rail are now incorporating many IOT devices, including PoE IP cameras, Wireless Access Points for Hotspots, Voice over IP communications, monitoring and digital signage. Ethernet switches, provided by CTC Union, for this market segment, include EN50155 certifications, utilize rugged M12 connectors and provide a wide range for DC power connections.

• PIS • CCTV • WiFi Series • Intercom System

Controller

TTDP

Monitor

4G Router

Gateway WiFi

TTDP (Train Topology Discovery Protocol) for train inauguration is a process where the network devices can automatically reconfigure for topology changes (i.e., as carriages are swapped). TTDP identifies the order of the Ethernet switches in a train backbone from the head and allows auto-reconfiguration of the other switches in the entire network.

Car 1

Car 2

Car 1

Car 2

Exchange



Related Products ITP-2204 / 1204 / G802 / 802 / 800 / 500 Series


EN 50155 Switches

EN45545-2

Add

Car 3

Remove

Remove & Add

Resilient Bypass EN50155 compliant products offer two copper interfaces with auto bypass function in the event of sudden power loss, particularly in daisy chain or linear topology networks. When power failure occurs in one of the switches on a train, the bypass relay function can activate, automatically bypassing the internal circuits and maintaining link between neighboring equipment. With this function, secure data transmission from terminals to backbone and higher network availability can be guaranteed. Bypassing

R


4

R


Industrial Product Series PoE Series Related Products IGS-2408 / 1608 / 803 / 402 / 600 Series IEXT224-4PH INJ-IG60-24 / INJ-IG01-PH

Please check page 15, 16 & 17 for more details.

PoE Switches • Supports PoE/PoE+/PoE++ IEEE802.3af/at/bt: 15.4/30/36/60Watts high power budget • Up to 8-port PoE (DIN-RAIL models) and 24-port PoE (Rackmount) • Redundant dual power input of 24/48VDC (20~57VDC), supports negative power (-)48VDC • High efficiency of power boost (94%~97%) • Supports 4KV surge protection and 2.25KV Hi-pot isolation • Advance PoE management: PD auto check and reset, PoE on/off scheduling (weekly/hour)

Remote PD Auto Test & Reset Auto checking and auto reset Powered Devices (PDs), when PD link failure The feature helps to reduce the operation and maintenance cost

Step 1

Step 2

PD Status is Good

No Response from PD

PD PoE Camera

PD Status Good!

Reset PD

PD Alive!

No Response...

Testing Request

Step 3

Testing Request Testing Echo

PoE

Power OFF

Power ON

Bus Surveillance System – 24VDC power booster required As IEEE 802.3af/at standard require the power input of 44~57VDC to supply PDs 15.4~30W power feeding. The dilemma of many applications that only 24VDC power be available, typically of Vehicles/Buses battery source. CTC Union PoE switches, design with the power booster circuit are able to boost input power from 24VDC to 48~57VDC power output, to solve the difficult situation of connect with PoE camera on bus surveillance application.

Camera 2

Camera 3

NVR

Monitor 1

Camera 1

24VDC Output Power Battery

Supports 24VDC power Input on vehicles application

5

www.ctcu.com


www.ctcu.com

Negative Voltage IEEE 1588 V2

PoE LAN Extender • High-speed long distance copper connections; up to 300m at 100Mbps and up to 1.2km at 50Mbps (over coaxial cable); 16Mbps (over twisted-pair copper wires) • Complies with IEEE 802.3at PoE long distance; up to 300m at 30W power budget over coaxial cable • Plug and Play to reduces configuration time • One step to upgrade the existing CCTV to IP cameras Please check page 14 for more details.


NEMA TS2

24AWG Copper Wire SNR

6dB

6dB

Profile

Asymmetrical

Symmetrical

Distance

Upstream Rate (Mbps)

Downstream Rate (Mbps)

Upstream Rate (Mbps)

Downstream Rate (Mbps)

300 m 400 m 600 m 800 m 1,000 m 1,200 m

65 45 30 10 6 1

100 95 65 45 35 20

100 70 45 27 18 8

100 70 45 27 18 16

PoE Output Budget

30W 20W 15W 7W 5W 4W


Regulated

Outdoor AP

Local Power

40-60 VDC or External AC to DC Adaptor

Ethernet

Don’t need power supply

up to 1.2km Copper/Coaxial

Ethernet

Remote Power Feeding IEXT224-4PH

Local

Data Power Simultaneously

IP Cam

Power IEEE802.3at PoE Data Fast Ethernet

IEXT224-4PH

e to lcom We

Total Power Budget of 30W for 4 PoE(PSE) Ports

Remote


Remote Power Feeding Enable

U CTC

Display

PoE Injectors • Easy to install PoE PD in the existing network topologies • Provides 1 port IEEE802.3af/at power supplying • Selectable 15.4/30W/36W,60W,72W PoE power output • Supports PoE mode A (Midspan) and mode B (Endspan) • Regulate PoE output voltage to stabilize power device, and guarantee the power feeding distance up to 100metter • Supports 4 pairs (60W/72W) PD handshake request ( such as AXIS® IP Camera) Please check page 15 for more details.

Gigabit Ethernet PoE Injector application Gigabit Ethernet

Gigabit Ethernet + PoE 15.4W

Non-PoE Ethernet Switch/HUB

/

30W

/

36W

/

60W

/

72W

INJ-IG60-24 & INJ-IG01-PH

PoE PD Device ®

ex. AXIS Q60 series in 60W mode

R


6

R


Industrial Product Series 4G WiFi Gateway / Router Related Products ICR-W403 / ICR-4103

WiFi

LTE

4G


ICR-W403

ICR-4103

• Provides dual 4G LTE Cellular SIMs for fail-over redundancy • High performance IEEE802.11a/b/g/n/ac (5GHz & 2.4GHz) connectivity • GNSS fleet tracking (GPS) • DI/DO port, Serial port ideal for IoT application • High security on various VPN protocols, built-in Firewall and Authentication • Ruggedized design with vibration, shock, wide operating temp. • Certified by EN 50155, E-Mark, EN 60950-1, CE, FCC

• Supports Multi-band 4G FDD/TDD LTE, WCDMA, GSM 900/1800MHz, LTE Cat4 • Built-in dual SIM card slots for network redundancy • Supports 2 DI, 1 DO interface • Supports 2 RS-232, 1 RS-485 (2-wire) Serial COM port • Integrated dual detachable antenna • Supports IPv6/IPv4, PPPoE, Static Routing and RIP1/2, Qos, VLAN, NAT

Wireless Transmission in Logistics Center

Vehicle Location Tracking System

7

www.ctcu.com

Transportation / Bus Communication 4G LTE

e

Eth

ter

ou

R iFi GW 3

t rne

4 -410 R IC

LED Display

4 -410 R IC

03

-41

TIM E

10:2

ter

ou

R iFi GW 3 ICR

esei NO 0 TA natio .115 IPEI n 5O N TI ME D

Remote Control Center

Billboard

Bus Location Ticketing Information

ter ou 03 Fi CRR-41 i GW I

Bus Stop



www.ctcu.com


4


FieldBus to Fiber Converters PROFIBUS

Related Products IFC-FDC-PRO / IFC-Serial-PRO / IFC-Serial-CAN IFC-FDC / IFC-Serial


• Redundant fiber ring with zero recovery time • Auto baudrate detection and data speed up to 12Mbps for ProfiBus series • Protocol transparent of Modbus, ProfiBus and CAN bus • Alarm by relay output • 2.5KV isolation protection • Dual-power inputs for redundancy • Extends PROFIBUS transmission distance up to 60 km • Wide temperature range model available for -40 to 75°C environments

PROFIBUS Network Benefits

IFC-FDC-PRO

PLC

Sensor

HMI

Digital power meters 0004 12

IFC-FDC-PRO

Fiber PROFIBUS

5F

Fiber Ring

1. EMC/noise isolation, to reduce mutual interference between serial port device 2. Extend distance by fiber 3. Cable redundancy 4. Isolate PROFIBUS failure 5. Achieve a reliable network environment PROFIBUS

0004 12

5F

Digital HMI power meters IFC-FDC-PRO

Sensor

PLC

IFC-FDC-PRO IFC-FDC-PRO

R


8

R


Industrial Product Series Negative Voltage

IEC 61850-3 Switches

IEC 61850-3

GOOSE

Related Products IPS-M2404S / IPS-G803SM / IPS-803GSM


• IEC 61850-3, IEEE 1613 certified is designed to fulfill power substations • Supports µ-Ring and µ-Chain, RSTP/STP/MSTP, and ERPS G.8032 for network redundancy • Isolated redundant power supplies with universal 24/48 VDC or 110/220 VDC/VAC power supply range • Hot-swappable interface modules for rackmount model • Cable diagnostic and Green Ethernet • -40 to 85°C operating temperature range

GOOSE Message For mission-critical applications, GOOSE messages can be placed into the highest QoS priority so as to avoid packet loss and delay. • IPS series Ethernet switches can communicate with GOOSE multicasts. • Critical communications are prioritized with the highest QoS priority. • Achieve zero packet loss to ensure reliable transmissions.

Hydroelectric Power Stations

Wind Power Plant

GOOSE

Solar Energy Power Plant

Power Substation

Power Substation Primary Reference Clock (PRC)

IEEE 1588v2

SCADA Wind farm

Solar power

Hydroelectric power

Nuclear power

E OS GO V2 588 E1 E E I

Thermal Power

µ-Ring E OS V2 GO 588 E1 E E I

PLC

GO OS IEE E E1 588 V2 PLC

VT/CT IDE

9

www.ctcu.com

Electric power sensor

VT/CT

Power Substation

Reliability Elements Certification ● ● ● ●

CE/FCC UL 60950-1 EN 50155 EN 50121-4

● ● ● ●

IEC 61850-3 EN 61000-6-2 EN 61000-6-4 NEMA TS2

Redundant Ring ● ● ● ● ●

µ-Ring ITU-T G.8032 802.1d STP 802.1w RSTP 802.1s MSTP

EMS Industrial Grade ● ● ● ● ●

u-Ring

EN 61000-4-2 ESD Level 3 EN 61000-4-3 RS Level 3 EN 61000-4-4 EFT Level 3 EN 61000-4-5 Surge Level 3 EN 61000-4-6 CS Level 3




www.ctcu.com

Rugged Mechanical

● Wide Temperature Models Available

● Vibration IEC 600068-2-6 ● Free Fall IEC 600068-2-32 ● Shock IEC 600068-2-27

High MTBF & 5 Years Warranty ● Industrial Grade Component ● Fanless

Brief Comparison between general CE & EN50121-4 Surge 　Signal L-E 　Signal L-L 　DC Power L-E 　DC Power L-L ESD (Contact) Radio frequency magnetic field EFT (fast transient) Power magnetic field Pulse magnetic field

CE Compliant

EN50121-4 Compliant (Trackside)

1kV N/A 0.5kV 0.5kV 4kV 10V/m 0.5kV Criteria B* 10 A/meter N/A

2kV 2kV 2kV 2kV 6kV 20V/m 2kV Criteria A* 300 A/meter 300 A/meter


Temperature


Reliable

* Criteria A: During the test storage devices shall maintain normal operation both in read/write and in stand-by conditions. * Criteria B: During and after the test failures which can be recovered by read and write retires are permissible (temporary delay in processing caused by this process is acceptable).

Key Certifications To reduce risks of electric shocks, fire, energy related hazards, heat related hazards, mechanical hazards, radiation, and chemical hazards for operator, layman or service personnel.

EN61000-6-2 EN61000-6-4

For Heavy Industrial Environment application.

E13

For car and motorcycle spare parts and security products, noise and emissions, are required to act in accordance with the EU.

For traffic control. NEMA TS2

EN50155

For trackside and railway applications. EN50121-4

For rolling stock, vehicle and moving machine applications.

For power substation applications. IEC 61850-3

R


10

R


Reliable Industrial Ethernet Products Advanced 4KV Surge Protection for PoE & UTP PoE Switch

Surge Protect

4KV Supports Negative Power Input • RS232 ground isolation from power ground

• Reverse polarity protection

• Negative Power System

V-

• Reverse Polarity Protection

V-

-48

V+

-48

V+

RS232

RS232

No Protection

Isolation

Not support Negative Power Model

V-

0

V+

+48V

Reverse Polarity Protection

Supports Negative Power Model

Management Software TM

CTC Union’s Industrial Device Management System is a comprehensive management tool, including SmartView Element Management System (EMS), TM

Central EMS and SmartConfig . Whether it is for monitoring, configuration, maintenance, or troubleshooting, the management software has a tool for every task.

SmartView

TM

EMS

TM

SmartConfig

• Main Functions (FCAPS) : Fault, Configuration, Accounting, Performance and Security Management • Remote access control for efficient configuration • Traffic / performance monitoring and management • Alarm trap and event log management • Auto discovery and device Viewer • Allow up to 25 administrators to login

• Multiple device auto discovery • Group configuration, access • Group firmware upgrade • Backup / restore device configuration • IP address assignment • Connectivity testing

Please check the Industrial catalog chapter 1 for more details.

11

www.ctcu.com


www.ctcu.com

Powerful Cybersecurity - Port Security Static MAC Table Configuration

Delete

Add the allowed MAC address

VLAN ID 1

MAC Address F0-DE-F1-0B-65-8D

1

Port Members 2 3


Step1

System Configuration Mode

Enable

Aging Enable Aging Period

Step2 Enable un-know MAC limit at zero

3600 Seconds

Port Configuration Disable

Mode

Limit 4

None

Action

Disabled 1

State

2

Enable

0

Shutdown

Ready


Port 1

MAC Whitelist

Hacker’s MAC


F0-DE-F1-0B-65-8D F0-DC-F1-5B-70-2D F0-DF-F1-4B-72-9D F0-DA-F4-3C-22-1A

AB-CD-EF-0B-65-4W

Powerful Cybersecurity - NAS RADIUS/ ISE Server

IEEE802.1X Authentication

Send access request for authentication by ID

Send username & password

NAS

RADIUS/ ISE Server Learn & authenticate the source MAC address

Send MAC address (First packet)

MAB

(MAC Authentication Bypass) Port Configuration

Port

Admin State

1

MAC-based Auth.

2

Force Authorized

NAS RADIUS-Assigned Qos Enable

RADIUS-Assigned VLAN Enable

Guest VLAN Enable

1

R


12

R


Reliable Industrial Ethernet Products IEEE 1588 PTP v2 in Smart Grids S Power Substation

Supports 5 operating mode

IEEE 1588 v2

S IEEE 1588 v2

• Ordinary-Boundary • Peer to Peer Transparent Clock • End to End Transparent Clock • Master • Slave

S

M

Wind Power Plant

Backbone Network

S

Solar Energy Power Plant

S Slave

Primary Reference Clock (PRC)

IEEE 1588 PTP v2 Application in Power substation & Smart Grid

M Master

µ-Ring Network Redundancy The µ-Ring is a proprietary redundancy protocol developed by CTC Union that supports flexible ring topologies. Multiple µ-Ring

• Friendly µ-Ring Configuration

Master

1 2 3 4 5

• Up to 5 rings • Up to 250 devices in a ring • µ-Ring, µ-Chain, Sub-Ring for different applications • Recovery time < 10ms • User Friendly configuration GUI

• µ-Chain topology • Benefit: Mix CTC and third party device in a ring topology Third Party Network

Slave

Edge

• Sub-Ring topology • Benefit: 1. Device redundancy (A & B)

Backup Path

Edge

Master

Ring

B

Backup Path

A

µ-Chain Slave

2. Cable redundancy

Slave

Backup Path

Sub-Ring

Slave

Supports Standard ITU G.8032 ERPS, MSTP, RSTP, STP for Network Redundancy

ITU G.8032

13

www.ctcu.com

Other than the proprietary µ-Ring redundancy protocol, standard ring redundancy protocols such as ITU G.8032 ERPS, STP, RSTP and MSTP are also supported. Among standard redundancy protocols, G.8032 ERPS, achieves the fastest recovery time (