FORD EXPEDITION (2007). FORD F-150 (2004-2007). LINCOLN MARK LT (
2006-2007). NOTE: READ ... removing or handling plastic parts of a vehicles
dash. ... Begin installation by removing the panel below the radio bezel. Insert a
Dash ...
060307-1
Part Number: FOR-205-07
INSTALLATION INSTRUCTIONS FORD EXPEDITION (2007) FORD F-150 (2004-2007) LINCOLN MARK LT (2006-2007)
Always check our website for the most updated model year compatibility information.
NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever you are removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will be right side up and readable when installed.
TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), 9/32” Socket and Driver PARTS INCLUDED: One Custom Bezel Mount and Instructions. LOCATION OF MOUNT: To the right of the radio. Step 1. Begin installation by removing the panel below the radio bezel. Insert a Dash Trim tool (part #SIT-104) in the location as shown in the picture to the left. Work your way around the panel releasing all the clips. Set the panel aside in a safe place. Continue by removing the bezel around the radio. Insert a Dash Trim tool (part #SIT-104) on the right side of the bezel and work your way around releasing all the clips. Note: You do not need to disconnect any wiring to the bezel. Just move the bezel to the left to gain access to the two (2) 9/32” screws on the right side of the radio. Step 2. Next remove the two (2) 9/32” screw on the right side of the radio. Set the screws aside in a safe place. Place the Custom Bezel Mount over the existing screw holes and replace the factory screw.
Install Mount Here
Carefully reinstall the dash in reverse order securing all wiring to the bezel and screws. Install any Bracketron phone holder or Amps compatible device to your Custom Bezel Mount. Your installation is complete.
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information. Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount. Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443 Web Address: www.bracketron.com
060307-1
Part Number: FOR-205-07
INSTALLATION INSTRUCTIONS LINCOLN NAVIGATOR (2007)
Always check our website for the most updated model year compatibility information.
NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever you are removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will be right side up and readable when installed.
TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), #2 Phillips Screwdriver. PARTS INCLUDED: One Custom Bezel Mount, Instructions, Two (2) #8x3/4” self tapping screws LOCATION OF MOUNT: To the right of the climate controls.
Step 1.
Remove Screws
Begin installation by removing the chrome trim around the shifter. Note: Use caution when working around the wood grain trim. The trim can scratch easily. Next open the center console and insert a Dash Trim tool (part #SIT-104) under the back edge of the panel around the shifter and cup holders. Work your way around the panel releasing two (2) clips on the right side, two (2) clips on the left side, and two (2) more in the front. Set the panel aside in a safe place. Step 2. Next under the ash tray there is two (2) 9/32” screws. Note: See the picture to the left for guidance. Remove these two (2) screws and set them aside in a safe place. Continue by removing the bezel around the radio. Insert a Dash Trim tool (part #SIT-104) in the location as shown in the picture to the left. Work your way around the bezel releasing a total of six (6) clips. Note: You do not need to disconnect any wiring to the climate controls. Just move the bezel to the left to gain access to the area to mount the Custom Bezel Mount.
Install Mount Here
Step 3. Insert the Custom Bezel Mount in the location as shown to the left. The Custom Bezel Mount should rest firmly in the corner. Use the supplied #8x3/4” self taping screws and a #2 Phillips screwdriver to secure the mount down. Carefully reinstall the dash in reverse order securing all wiring to the bezel and screws. Install any Bracketron phone holder or Amps compatible device to your Custom Bezel Mount. Your installation is complete.
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information. Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount. Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443 Web Address: www.bracketron.com
