installation instructions installation instructions ... - Metra Electronics
Recommend Documents
DIN HEAD UNITS: Using the scored lines on the back of the Radio Housing as a guide, cut and remove the shaft supports. S
If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening). 2-SHAFT HEAD UNITS: Snap the Fac
Brackets by inserting the Spacer pegs into the Bracket holes. Slide the aftermarket head unit into the back of the kit a
water in a small bore domestic central heating system where ... The wiring
diagram above shows relevant connections to a Honeywell junction box (Part No.
Page 1 of 15 Installation Instructions for: EMS P/N 30-6051 (4 cylinder Acura/Honda vehicle with 6 cylinder engine and harness swap) Vehicle: 2000-2001 Acura Integra
disconnect the wiring. 1. DODGE Stealth 1991-96 / MITSUBISHI 3000GT 1991-
98. 2. 3 ... Skip to the Installation Instructions for ALL VEHICLES on Page #12.
DASH TRIM BEZELS WITH .... MITSUBISHI Diamante 1994-96. MITSUBISHI
Eclipse ...
Installation instructions for 99-5510. • DIN radio provision ... WIRING & ANTENNA
CONNECTIONS (sold separately) ..... Ford Taurus/Mercury Sable 1990-1995.
Locate the factory wiring harness in the dash. ... the Radio Housing with (2)
Carriage Bolts and. (2) Keps Nuts. ... Reatta 1990-91* ... S10 Blazer 1982-85*.
AUDI. A4/A6/A8 1996-1999. A4 (with Concert Radio) 2001-2004. Audi TT 2001-
2006. C. D ... front of the radio. 5. Locate the factory wiring harness in the dash.
Metro (Geo included) 1995-2001. Monte Carlo 2000-2005 ... Honda. Passport
1998-2002. Hummer. H1 2003-2006. H2 2003-2007. Isuzu. Ascender 2003- .....
Unsnap the driver's side fuse panel cover and .... glove box location. 3. Remove (
2) ...
A) Radio Housing B) ISO Brackets C) Rear Support Bracket D) ISO Trimplate E) (
1) #8 X 3/8”Phillips Truss ... Ford Explorer 2002-2005 ... FORD MUSTANG 2001-
2004 .... CONEXIONES DE CABLEADO Y ANTENA (se venden por separado).
Unsnap the top edge of the knee bolster panel. Remove. (1) phillips ... entire
dash trim bezel and remove. Open doors ... BUICK Regal 1995-2000.
CHEVROLET ...
A) Integrated Mounting Kit • B) 70-5715 Extension Harness • C) 70-5716 Harness
... FORD Taurus and Mercury Sable 1996-1999. ⅢAⅢ. ⅢBⅢ. ⅢCⅢ. ⅢDⅢ ...
wiring harnesses into the switch connectors (previously mounted in step #2) and.
INSTALLATION INSTRUCTIONS FOR PART 99-8222. 99-8222/ ... E) Double DIN
/Stacked ISO Trim Plate • F) Snap in Pocket • G) Radio Housing Brackets.
Acura RSX 2002-2005. 1. Unclip the lower dash panel (containing the power
outlet) and remove the panel. 2. Reach into the opening and remove. (2) Phillips
...
panel. Remove (1) torx-head screw from each a/c vent. Unclip the dash trim bezel
and remove. 1. BUICK Reatta 1990-91. 2. Remove the ..... CHEVROLET Blazer/S
-10 Pickup · GMC Jimmy/Sonoma 1998-02. Disconnect ... Unsnap the fuse box.
Chevrolet. Avalanche 2003-2006. Blazer 2002-2005. Cavalier 2000-2005.
Colorado ... Tracker 1992-2004. Trailblazer ..... Unsnap the driver's side fuse
panel.
70-9221 - 99-up Volvo harness,. • 40-VL10 - Volvo Antenna Adapter interface ...
Make wiring connections using the EIA color code chart shown below and the ...
Panel removal tool ... dash. Metra recommends using the proper mating adaptor
and making ... CHRYSLER Sebring 1995-00 / DODGE Avenger 1995-00.
INSTALLATION INSTRUCTIONS FOR PART 99-5813. 99-5813. APPLICATIONS.
LINCOLN. Navigator 2007-up / MKX 2007-2010. MKZ 2007-2009 / Zephyr ...
installation instructions installation instructions ... - Metra Electronics
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Rev. 04-10-09
2007 AND UP
Rev. 04-10-09
2007 AND UP
Rev. 04-10-09
2007 AND UP
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
CHRYSLER/DODGE/JEEP VEHICLES
CHRYSLER/DODGE/JEEP VEHICLES
CHRYSLER/DODGE/JEEP VEHICLES
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
Due to the fact that a switched 12-volt accessory lead does NOT exist in the factory harness, an accessory source must be located. 1. Using the separate red wire provided with the fuse tap, locate an accessory power source in the vehicle’s fuse box. 2. Connect this red wire to the aftermarket head unit switched accessory lead. 3. Use Metra’s standard wiring instructions for the remainder of the installation.
