Golf 2-door, GTI. Note: Trim fits over sealing flange of door inner seal. 1 - Trim.
Removing: ... Remove rear side panel trim page 70-34 . ... Golf 4-door, Jetta. Note
:.
70-23
Interior trim panels, servicing A-pillar trim, upper, removing and installing Note: Trim fits over sealing flange of door inner seal, see sectionalized view. 1 - Trim Removing: - Removing B-pillar trim (upper)
page 70-24 .
- Remove Phillips-head screw -2-. - Pull off and unhook retaining lugs -3-. Installing: - Check seating and condition of clips -4- and correct if necessary. - Hook-in retaining lugs -3- first. 2 - Phillips-head screw 3 - Retaining lug 4 - Clip With foam padding Pushed into A-pillar trim mount
70-24
B-pillar trim, removing and installing Golf 2-door, GTI Note: Trim fits over sealing flange of door inner seal. 1 - Trim Removing: - Remove sill panel trim
page 68-19 .
- Remove front seat belt anchor - Remove rear side panel trim
Repair Group 68. page 70-34 .
- Pull trim off starting from bottom. Installing: - First locate retaining lugs (arrow) in A-pillar and Cpillar trim. - Check function of belt height adjuster.
70-25
2 - Adjuster 3 - Cover cap 4 - Clip Pushed into B-pillar mount 5 - Mount for clip
70-26
Golf 4-door, Jetta Note: Trim fits over sealing flange of door inner seal. 1 - Upper trim Removing: - Remove sill panel trim
page 68-19 .
- Remove front seat belt anchor
page 69-17 .
- Pull trim off starting from bottom. Installing: - First locate retaining lugs (arrow) in A-pillar and Cpillar trim. - Check function of belt height adjuster. 2 - Phillips-head screw
70-27
3 - Lower trim Removing: - Remove sill panel trim
page 68-19 .
- Remove front seat belt anchor
page 69-17 .
- Remove upper trim -1- and seat belt anchor. - Remove Phillips-head screw -2-. - Pull trim off starting from top. 4 - Cover cap 5 - Adjuster
70-28
C-pillar trim, upper, removing and installing Golf, GTI 1 - Clip With foam padding Pushed into trim mount 2 - Trim 3 - Clip 4 - Foam padding 5 - Hex nut 6 - Adjuster 7 - Cover 8 - Cover Only vehicles without rear seat belts 9 - Phillips-head screw
70-29
Removing - Remove sill panel trim
page 68-19 .
- Removing B-pillar trim (upper)
page 70-24 .
- Remove luggage compartment cover support 36 .
page 70-
- Remove Phillips-head screw -9-. - Remove hex nuts -5-. - Pull off trim along roof edge and remove squarely from clips -3-. - Remove lower C-pillar trim trim page 70-34 .
page 70-32 or side panel
- Remove seat belt anchor. Installing - Check seating of clips -3- and adjust if necessary. - Check seating and condition of clips -1-, correct if necessary. - Check function of belt height adjuster.
70-30
Jetta 1 - Clip With foam padding Pushed into trim mount 2 - Clip 3 - Foam padding 4 - Trim 5 - Adjuster 6 - Cover 7 - Cover Only vehicles without rear seat belts 8 - Phillips-head screw
70-31
Removing - Remove sill panel trim
page 68-19 .
- Removing B-pillar trim (upper)
page 70-24 .
- Remove screw -8-. - Pull off trim along roof edge and remove squarely from clips -2-. - Unhook parcel shelf trim. - Remove lower C-pillar trim
page 70-32 .
- Remove rear seat belt anchor. Installing - Check seating of clips -2- and adjust if necessary. - Check seating and condition of clips -1- and correct if necessary. - Check function of belt height adjuster.
70-32
C-pillar trim, lower, removing and installing Golf 4-door, Jetta Note: Trim fits over sealing flange of door inner seal. 1 - Trim Removing: - Remove seat and backrest. - Remove sill panel trim
page 68-19 .
- Remove upper B-pillar trim
page 70-26 .
- Remove upper C-pillar trim or Page 70-30 (Jetta).
page 70-28 (Golf)
- Remove pin -2- and press buttons -3-. 2 - Backrest locking pin
70-33
3 - Press button Unscrew or push on 4 - Securing eye Secured with rear sill panel trim plug.
70-34
Side panel trim, removing and installing Golf 2-door, GTI 1 - Securing point For clips -22 - Clips Attached to flange (side window) 3 - Side panel trim Removing: - Remove seat and backrest. - Remove sill panel trim -7-
page 68-19 .
- Remove pin -4-, press button -5- and Phillips-head screws -8-. - Pry out plugs -6-. - Pull trim off clips -2-.
70-35
4 - Backrest locking pin 5 - Press button Unscrew or push on 6 - Plugs Pry out with lever 80-200 7 - Sill panel trim With securing clip 8 - Phillips-head screw 9 - Clip For securing Phillips-head screws -8-.
70-36
Luggage compartment cover Golf, GTI 1 - Threaded pin Welded on 2 - Hex nut 3 - Support Removing: - Remove luggage compartment cover. - Remove hex nuts -2-. - Unclip support from C-pillar trim (arrow).
70-37
Parcel shelf, removing and installing Jetta
1995 m.y.
1 - Securing pin 2 - Trim Removing: - Removing upper B-pillar trim
page 70-26
- Removing upper C-pillar trim
page 70-30
- Lift trim front edge and unhook from clips -3- Pull off front trim forward 3 - Clip
70-38
Jetta 1996 m.y. 1 - Securing pin 2 - Trim With holes for rear speakers - 4 - and - 5 Removing: - Removing upper B-pillar trim
page 70-26
- Removing upper C-pillar trim
page 70-30
- Lift trim front edge and unhook from clips -3- Pull off front trim forward 3 - Clip 4 - Rear treble speaker (tweeter) Relocated from rear door trim 5 - Rear bass speaker (woofer) Relocated from rear door tray
70-39
Rear lid trim, removing and installing Golf, GTI 1 - Rear lid trim Removing: Remove Phillips-head screw and unclip trim 2 - Phillips-head screw 3 - Spreader nut 4 - Mounting clip 5 - Tailgate
70-40
Luggage compartment side trim, removing and installing Jetta 1 - Storage box 2 - Plug Pry out with lever 80-200 3 - Phillips-head screw
70-41
Molded headliner, removing and installing 1 - Molded headliner Removing
page 70-42
2 - Rear trim strip Clipped onto roof frame 3 - Cover cap/grab handle 4 - Grab handle 5 - Phillips-head screws 6 - Spacer/interior light On vehicles with sunroof spacer is located in front of cut-out/interior light (in direction of travel). 7 - Center marking Align to center of vehicle (center clip hole)
70-42
Removing molded headliner Golf 2-door, GTI - Remove sill panel trim - Remove side panel trim
page 68-19 . page 70-34 .
Golf (all), GTI - Remove luggage compartment cover support page 70-36 . Continuation for all vehicles - Disconnect battery Ground (GND) strap. - Pry out interior light using screwdriver and disconnect harness connectors.
70-43
- Remove cable drive cover and sunroof pull out beading (vehicles with sunroof only).
- Sun visor -1- and sun visor mount -2- ( turn sun visor mount through 90 remove) remove screws (arrows) (if installed, disconnect connector). - Remove upper B-pillar trim
page 70-24 or
- Remove upper A-pillar trim
page 70-23 .
- Remove upper C-pillar trim
page 70-28 or
Page 70-26 .
Page 70-30 .
to
70-44
- Pull trim strip off, -1- securing clip Removing roof handles
- Fold handle -1- down. - Pry cover -2- up using screwdriver and fold open. - Remove Phillips-head screws -3- and take off handle -1-. On vehicles with a sunroof the front grab handles are marked with a "V" and the rear with an "H". - Lower molded headliner and with help from second technican (danger of breakage) and remove from vehicle.
