marine diesel engine

Rating definitions: . hp=0.7355kW Ratings are based on conditions of 100kPa, 30% relative . humidity at 25 ° C. S=For applications where use of rated power is less than 30 minutes continuous. L=For applications where use of rated power is less than 2 hours continuous. M=For applications where use of rated power is less than 10 hours continuous. H=For applications where use of rated power is less than 24 hours continuous. Fuel rates: Specific gravity 0.835g/cc, low calorific value 42700kj/kg (10200kcal/kg), Cetane No.45. Note: All data subject to alteration without notice. Photograph may show optional equipment.

MARINE DIESEL ENGINE PRODUCT GUIDE

Yanmar Asia（Singapore）Corp. Pte. Ltd. 4 Tu as Lane, Sing apore 638613 Tel : 65-6861-3855 Fax : 65-6862-5195

Yanmar Europe B.V. Brugplein 11, 1332 BS Al me re -de Vaa rt, The Netherl ands Tel : 31-36-5493200 Fax : 31-36-5493209

Yanmar Marine U.S.A. Corp. 101 Internat ional Pa rkw ay, Adai rsville, G A 30103, U.S. A. Tel : 1-770-877-9894 Fax : 1-770-877-9009

Yanmar Engine（Shanghai）Co., Ltd. 18F, North Tower, Shanghai Stock Exchange Bu ilding, 528 South Pudong Road, Pudong Shanghai, China, P.C.（200120） Tel : 86-21-6880-5090 Fax : 86-21-6880-8090

Yanmar Marine System Co., Ltd. 5-3-1, Tsu kaguchi-honmachi, Amag asaki, Hyogo, Japan Tel : 81-6-7711-6405 Fax : 81- 6-6428-0485

Yanmar Co., Ltd. 1-32, Chayamachi, Kit a-ku, Osaka, Japan 001M0-G00390 0904 H

Reliability, Economical efficiency & Comfort for customers dedicated to maritime activity. Our pride is to contribute to

MARINE

PROPULSION

DIESEL ENGINE

tough and valuable activities of customers on the sea.

[2]

[3]

2GMY MARINE

PROPULSION

M・L- rating 8.8~9.7kW (12.0~13.2mhp)

4JHYE MARINE

PROPULSION

M・L- rating 25.7~29.4kW (35~38mhp)

DIESEL ENGINE

DIESEL ENGINE

• Pre-combustion chamber. Two cylinders. • 2GMY is equipped with mechanical marine gear.

• 4-cylinder, direct injection, heat exchanger cooling. • Natural aspiration. • Yanmar YX marine gear is standerd.

mm lit. kW(hp)/rpm

Combution system Aspiration Starting system Cooling system Marine gear Dry mass Dimensions (L×W×H)

kg mm

2GMY 2 in-line 72 × 72 0.586 M : 8.8(12.0)/3200 L : 9.7(13.2)/3300 Special swirl precombution chamber Natural aspirated Electric motor (12V 1.3kW) Direct sea water cooling Mechanical 155 with Y-5M 712.5×463×598 with Y-5M

Rear view

Combution system Aspi ration Starting system Cooling system Marine gear Dry mass Dimensions (L×W×H)

mm

lit.

kg

Dimensions Unit:mm Right side view

463 230 224

kW(hp)/rpm

mm

213

Rear view 926.5 532.5

170

Water outlet φ25

Right side view

545 278 140.6

267 247

5 50 8

695.5 712.5

433 33.5 100 45 101

9

Accessories •Exhaust pipe •Kingston cock •Stop cable 3m •Battery switch •A-type instrument panel •Wiring harness 3m •LO evacuation pump

4.5

170

66.5

45°

27.5 181

659

407 119.5

74 φ60

Water inlet φ26

φ100

221

100 10 6

116

598

329

377

491

62

100 210 300 454

4JHYE 4 in-line 78 × 86 1.644 M : 25.7(35)/3400 L : 29.4 (38)/3600 Di rect i njection Natural aspi rated Electric motor (12V 1.8kW) Heat exchanger Hydaulic 243 with YX-10 916.3×545×659 with YX-10

407.5

Dimensions Unit:mm

Specifications Model Number of cylinders Bore × stroke Displacement Rated output

226

Specifications Model Number of cylinders Bore × stroke Displacement Rated output

58 55.25

163

103

450.75 832.25 916.3

28.8

Accessories •Installation parts •Half coupling •Standard tools

[4]

•Exhaust pipe •Remote control head •Remote control cable 4m •B-type instrument panel •Wiring harness 4m •Standard spare parts

•Standard tools •Installation parts •Battery switch •Kingston cock •LO evacuation pump •FO water separato r •Bilge pump

[5]

4CHE3 / 6CHE3 MARINE

PROPULSION

M・L- rating 57.4~95.6kW (78~130mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Left side view 4CHE3

D

6CHE3

NO.1 CYL CENTER NO.4 CYL CENTER 912.5

C E

277 88 189

402 220

NO.6 CYL CENTER 1201.5

233.5

277.5

182

691

88 189

233

284

F B

G

64.5

H I

With gearbox / Rear view C

D

• Direct injection, heat exchanger cooling. • Natural aspirated 4- and 6-cylinder. • Durable hydraulic marine gear.

903

139

With gearbox / Left side view A

E

F B

D 232

E 292

F 734

G 9

6CHE3×YX-30-2

1496.3 1018 690

232.5 300

737

9

H 234

I 510

233

550

– Marine gear

Performance curves

tp

Ou

40 30 20 10 0

Specific Fuel Consumption (Cubic Curve) 1400

1600

1800

2000

2200

2400 2550

320 310 300 290 280 270 260 250

60

Output : kW

axim

(M ut

Specific Fuel Consumption : gr/kW・hr

) um

50

) um

80

axim

t (M

tpu

Ou

40

( ut

bic

e)

rv

Cu

Cu

tp

Ou 20

Specific Fuel Consumption (Cubic Curve) 0

1400

Speed of Crankshaft : rpm

1600

1800

2000

2200

2400 2550

300 290 280 270 260 250 240

Specific Fuel Consumption : gr/kW・hr

6CHE3

4CHE3

rv e)

60

Cu

Marine gear specifications Engine model : 4CHE3・6CHE3 Model YX-30 YX-20 Type Hydraulic multi-disc clutch, wet type Reduction ratio (Ahead) 2.55 2.96 3.48 2.03 Direction of rotation (propeller shaft) Clockwise or counter-clockwise viewed from stem kg 68 Dry weight 70

A B C 1183.5 1021 688

bic

kg mm

Model 4CHE3×YX-20-1

(C u

kW(hp)/rpm

H I

ut

lit.

G

Ou tp

Combution system Aspiration Starting system Cooling system Marine gear Dry mass Dimensions (L×W×H)

mm

4CHE3 6CHE3 4 in-line 6 in-line 105 × 125 4.330 6.494 M : 57.4(78)/2550 M : 84.6(115)/2550 L : 62.5(85)/2600 L : 95.6(130)/2600 Direct injection Natural aspirated Electric starting motor (24V 4.0 kW) Heat exchanger Hydraulic 568 700 1183.5×688×1021 1496.3×690×1018 with YX20 with YX30

Output : kW

Specifications Model Number of cylinders Bore × stroke Displacement Rated output

Speed of Crankshaft : rpm

Accessories •Breather hose with fittings •Drain separato r •Evacuation hand pump •Fresh water sub-tank •Alternato r 600W

•Instrument panel fo r wheel house (B/D-type) •Half coupling •Standard spare parts kit • Standard tool kit •Operation manual

[6]

•Installation parts •Exhaust bellows •Exhaust silencer •Sea water filter •Kingston •Bilge pump •Battery switch

•Remote control head & cable •Pipes fo r exhaust, sea water, fuel oil

[7]

6CH-HTE3/DTE3/UTE MARINE

PROPULSION

M・L- rating 125~206kW (170~280mhp)

Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Left side view

736

1201.5 340

815

6CH-HTE3 : 1096 6CH-DTE3 : 1096 6CH-UT3 : 1111

193

9

233 550

With gearbox / Front view

With gearbox / Left side view

C

• Direct injection, heat exchanger cooling. • Turbocharger + intercooler. • Durable hydraulic marine gear. • 6CH-DTE3 and 6CH-UTE conform to IMO emissions regulations.

G

A 1575

B 1096

C 736

D 193

E 340

F 815

G 9

H 233

I 550

6CH-HTE3×YX-71

1599.5

1096

736

193

340

815

9

233

550

6CH-DTE3×YX-71 6CH-UTE×YX-71

1599.5 1599.5

1096 1111

736 736

193 193

340 340

815 815

9 9

233 233

550 550

– Marine gear

0

Specific Fuel Consumption (Cubic Curve) 1400 1600 1800 2000 2200 2400 2550

Speed of Crankshaft : rpm

1400 1600 1800 2000 2200 2400 2550

Speed of Crankshaft : rpm

) um axim

rv

e)

t (M

bic (C u Ou

tp

ut

100

Cu

tpu

e) rv Cu

Specific Fuel Consumption (Cubic Curve) 0

260 250 240 230 220

150

Ou

um )

50

6CH-UTE

50

Specific Fuel Consumption (Cubic Curve) 0

1400 1600 1800 2000 2200 2400 2550

Speed of Crankshaft : rpm

Accessories •Breather hose with fittings •Drain separato r •Evacuation hand pump •Fresh water sub-tank •Alternato r 600W

•Instrument panel fo r wheel house (D-type) •Half coupling •Standard spare parts kit •Standard tool kit •Operation manual •Exhaust bellows

[8]

•Installation parts •Exhaust silencer •Sea water filter •Kingston •Bilge pump •Battery switch

•Remote control head & cable •Pipes fo r exhaust, sea water, fuel oil

[9]

260 250 240 230 220

Specific Fuel Consumption : gr/kW・hr

20

290 280 270 260 250 240 230

200

Output : kW

40

100

bic

) rve tpu t( Cu bic

Cu

tp u

Ou

60

Ou

80

6CH-DTE3

150

t( Cu

) um ax im t( M

100

Output : kW

Marine gear specifications Engine model : 6CH-HTE3, 6CH-DTE3, 6CH-UTE Model YX-50S(or YX-71) YX-71 Type Hydraulic multi-disc clutch, wet type Reduction ratio (Ahead) 2.58 2.91 3.53 2.07 Direction of rotation (propeller shaft) Clockwise or counter-clockwise viewed from stem kg 117 (or 214) Dry weight 214

170

pu

6CH-HTE3 120

Specific Fuel Consumption : gr/kW・hr

Performance curves

xim

kg mm

6CH-HTE3×YX-50S

Ou t

kW(hp)/rpm

I

t( Ma

lit.

H

Ou tpu

mm

6CH-HTE3 6CH-DTE3 6CH-UTE 6 in-line 105 × 125 6.494 M : 125(170)/2550 M : 154(210)/2550 M : 188(255)/2550 L : 140(190)/2600 L: 169(230)/2600 L : 206(280)/2600 Direct injection Turbocharger + intercooler Electric starting motor (24V 4.0 kW) Heat exchanger Hydraulic 795 900 940 1575 × 736 × 1096 1599.5 × 736 × 1096 1599.5 × 736 × 1111

Output : kW

Combution system Aspiration Starting system Cooling system Marine gear Dry mass Dimensions (L×W×H)

F B

Specific Fuel Consumption : gr/kW・hr

Specifications Model Number of cylinders Bore × stroke Displacement Rated output

A E

D

6CX-GTYE MARINE

PROPULSION

M・L- rating 265~294kW (360~400mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view

897

1496 1026

308 203

(25)

359

162

38.5

75

372

964

93

281

75

9 381

100

543

583

165

538 420.6

357 377.4 550

With gearbox / Rear view

With gearbox / Right side view 1586 398 308 203

1026

162

38.5

372

MINIMUM HEIGHT FOR RIMOVING PISTON

)

21

100 179 (9) 79 300

6CX-GTYE

250

(C

150

100

50

0

Specific Fuel Consumption (Cubic Curve) 1400 1600 1800 2000 2200 2400 2600 Speed of Crankshaft: rpm

240 230 220 210

Speific Fuel Consumption: g/kW.hr

ub ic

Cu rv

e)

200

tp ut

Marine gear specifications Engine model : 6CX-GTYE Model YX-71-1 Type Hydraulic multi-disc clutch, wet type Reduction ratio (Ahead) 2.58 2.91 2.07 Direction of rotation (propeller shaft) Clockwise or counter-clockwise viewed from stem kg 210 Dry weight

Performance curves

Ou

mm

– Marine gear

t

kg

180

tp u

kW(hp)/rpm

141 141 245

Ou

lit.

Output: kW

Combution system Aspiration Starting system Cooling system Marine gear Dry mass Dimensions (L×W×H)

mm

6CX-GTYE 6 in-line 110 × 165 7.413 M : 265(360)/2600 L : 294(400)/2700 Direct injection Turbocharger + intercooler Electric starting motor (24V 4.0 kW) Heat exchanger Without marine gear 1060 with YX-71-1 marine gear 1586 × 897 × 964

250

Specifications Model Number of cylinders Bo re × stroke Displacement Rated output

764

(

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler. • Durable hydraulic marine gear. • 4-valves per cylinder for higher combustion efficiency. • Conform to IMO emissions regulations.

Accessories •Breather hose with fittings •Exhaust flexible joint fo r T/C out •Drain separato r •Evacuation hand pump •Fresh water sub tank

•Alternato r 980W •Instrument panel fo r wheel house (D-type) •Half coupling •Daily maintenance tool kit •Operation manual •Standard spare parts

[ 10 ]

•Installation parts •Flexible mounting •Exhaust silencer •Sea water filter •Kingston •Bilge pump •Battery switch •Remote control head & cable

•Wiring harness •Pipes fo r exhaust, sea water, fuel oil

[ 11 ]

6HA2M-HTE MARINE

PROPULSION

H- rating 204kW (278mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view

1016

1584.5 870 No.1 CYL.

FOR REMOVING PISTON

874

771 1260

438

295

386

130

No.6 CYL.

276.5

836

517

159.5

CRANK CENTER

171.5

499 330

271 1087

With YX120L gearbox / Front view

199

With YX120L gearbox / Left side view

D

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler models. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by BV, GL, RINA. 6HA2M-HTE 6 in-line 130 × 165 13.140 H : 204(278)/1880 Direct injection Turbocharger + intercooler Electric starting motor (24V 6.0kW) Heat exchanger 1340 1584.5×1016×1260

B 420

C 1272

D 1016

E 499

6HA2M-HTE×YX-120L

2038.5

454

1384

1016

499

I

II

I

II

F 517 517 – Marine gear

Fuel Consumption: L/h

Performance curves Fuel consumption comparison

60

Fuel consumption

40 20 0

Output

0

50

100

150

200

250

Output: kW

Output: kW

250

YX-1 20L

200

Max. output

150 100 50

Propeller power curve

0 1500

4.00

B

A 2004.5

4.59

Torque: N・m

Marine gear specifications Engine model : 6HA2M-HTE Model YX-1 20 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.57 3.04 3.55 2.03 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 310 Dry weight

1584.5

Model 6HA2M-HTE×YX-120

Fuel Consumption : gr/kW・hr

Specifications Model Number of cylinders Bore × stroke mm Displacement lit. Rated output kW(hp)/rpm Combution system Aspiration Starting system Cooling system kg Dry mass (without marine gear) mm Dimensions (L×W×H)

A F

C

E

385

Torque Max.output

1000

500 Propeller power curve 0 600 800 1000 1200 1400 1600 1800 2000

Speed of Crankshaft : rpm

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Evacuation hand pump •Fresh water sub-tank

•Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

[ 12 ]

•YX gearbox •Installation parts •FPTO V-pulley •Exhaust silencer •Exhaust flexible joint for piping •Sea water filter •Kingston •Bilge pump •Duplex FO filter •Drain separato r

•2 pole wiring •Alternato r 980W •Remote control head & cable •2 station instrument panel (C-type) •Stop solenoid •Wiring harness •Pipes for exhaust, sea water, fuel oil

[ 13 ]

6HA2M-HTE MARINE

PROPULSION

M- rating 257kW (350mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view

1016

1584.5 276.5

870 No.1 CYL.

386

130

1260

771

874

836

438

295

No.6 CYL.

517

159.5

CRANK CENTER

171.5

499 330

271 199

1087

With YX120 gearbox / Front view

With YX120 gearbox / Left side view

D

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler models. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by BV, GL, RINA. 6HA2M-HTE 6 in-line 130 × 165 13.1 40 M : 257(350)/1950 Direct injection Turbocharger + intercooler Electric starting moto r (24V 6.0kW) Heat exchanger 1340 1584.5 × 1016 × 1260

B

6HA2M-HTE×YX-120

A 2004.5

B 420

C 1272

D 1016

E 499

6HA2M-HTE×YX-120L

2038.5

454

1384

1016

499

I

II

I

II

F 517 517 – Marine gear

Performance curves Specific Fuel Consumption: gr/kW・hr

Marine gear specifications Engine model : 6HA2M-HTE Model YX-1 20 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.57 3.04 3.55 2.03 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 310 Dry weight

1584.5

240 230

Specific fuel consumption (at cubic curve)

220 210 200 300 250

YX-1 20L 4.00

4.59

385

Output: kW

Specifications Model Number of cylinders Bore × stroke mm Displacement lit. Rated output kW(hp)/rpm Combution system Aspiration Starting system Cooling system kg Dry mass (without marine gear) mm Dimensions (L×W×H)

A F

C

E

200 150

t tpu

e)

urv

.c

ax

(M

Ou

100 50

) ve

ur

cc

i ub

(C ut

tp

Ou

0 800 1000 1200 1400 1600 1800 2000 2200 Speed of Crankshaft: rpm

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Evacuation hand pump •Fresh water sub-tank

•Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

[ 14 ]

•YX gearbox •Installation parts •FPTO V-pulley •Exhaust silencer •Exhaust flexible joint fo r piping •Sea water filter •Kingston •Bilge pump •Duplex FO filter •Drain separato r

•2 pole wiring •Alternato r 980W •Remote control head & cable •2 station instrument panel (C-type) •Stop solenoid •Wiring harness •Pipes fo r exhaust, sea water, fuel oil

[ 15 ]

6HA2M-DTE MARINE

PROPULSION

M- rating 298kW (405mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Left side view 1584.5

1036 276.5

870

130

No.1 CYL.

386

1260 771

874

438

290

No.6 CYL.

517

159.5

CRANK CENTER 836

171.5

519 362

271

With YX120 gearbox / Front view

With YX120 gearbox / Left side view

D

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler models. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by BV, GL, RINA. 6HA2M-DTE 6 in-line 130 × 165 13.1 40 M : 298(405)/1950 Direct injection Turbocharger + intercooler Electric starting moto r (24V 6.0kW) Heat exchanger 1350 1586 × 1036.5 × 1260

B

6HA2M-DTE×YX-120

A 2004.5

B 420

C 1272

D 1036

E 519

6HA2M-DTE×YX-120L

2038.5

454

1384

1036

519

I

II

I

II

F 517 517 – Marine gear

Performance curves 230 220

Specific fuel consumption (at cubic curve)

210 200

e)

190

t (M tpu

e) cu

rv

200

(C u ut

100

bic

150

Ou

4.59

Ou

250

ax .c urv

300

tp

Specific Fuel Consumption: gr/kW・hr

Marine gear specifications Engine model : 6HA2M-DTE Model YX-1 20L YX-1 20 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.57 3.04 3.4 6 4.00 2.03 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 310 Dry weight 385

1584.5

Output: kW

Specifications Model Number of cylinders Bore × stroke mm Displacement lit. Rated output kW(hp)/rpm Combution system Aspiration Starting system Cooling system kg Dry mass (without marine gear) mm Dimensions (L×W×H)

A F

C

E

50 0 800 1000 1200 1400 1600 1800 2000 2200 Speed of Crankshaft: rpm

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Evacuation hand pump •Fresh water sub-tank

•Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

[ 16 ]

•YX gearbox •Installation parts •FPTO V-pulley •Exhaust silencer •Exhaust flexible joint fo r piping •Sea water filter •Kingston •Bilge pump •Duplex FO filter •Drain separato r

•2 pole wiring •Alternato r 980W •Remote control head & cable •2 station instrument panel (C-type) •Stop solenoid •Wiring harness •Pipes fo r exhaust, sea water, fuel oil

[ 17 ]

6HYM-ETE MARINE

PROPULSION

H- rating 368kW (500mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view

1014 524

1556 490

18

277

870

352

39

747

866 1133 790

119

267

No.1

No.6

446

265

With YX161L gearbox / Rear view

With YX161L gearbox / Right side view 2149 812

870

352

277

39

446

678

535

lit. kW(hp)/rpm

kg mm

319

119 319 200

630

mm

6HYM-ETE 6 in-line 132.9 × 165 13.733 368(500)/1950 Direct injection Turbocharger + intercooler Electric starting moto r (24V 6.0kW) Heat exchanger 1385(without marine gear) 1556 × 1014 × 1133

Marine gear specifications Engine model : 6HYM-ETE Model YX-1 61L YXH-1 60 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.4 6 3.05 3.65 4.08 1.97 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 390 Dry weight 620

311

Specifications Model Number of cylinders Bore × stroke Displacement Rated output Combution system Aspiration Starting system Cooling system Dry mass Dimensions (L×W×H)

76

866

• 6-cylinder, direct injection, heat exchanger cooling. • Twin-turbocharger + intercooler. • Available either with marine gear or without marine gear. • 4-valves per cylinder for higher combustion efficiency. • Conform to IMO emissions regulations. • Type approved by NK, ABS, BV, RINA.

401

356

265 1947

– Marine gear

Performance curves

L/h 150

N·m 2500

Fuel Consumption

100

2000

50

1500

0 kW 400

Output

200 100

x.

Ma

t

tpu

ou

1000

300

4.55

Torque

a

M

t

pu

ut

o x.

er

pell

Pro

e

urv

er c

pow

500 0 1000

P

rve

r cu

owe

er p

ell rop

1200 1400 1600 1800 Speed of Crankshaft: rpm

0

Accessories •Breather hose with fittings •Fresh water sub-tank •Alternato r 980W •2 pole wiring •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •Wiring harness •2 station instrument panel (C-type) •Installation parts •FPTO V-pulley •Double walled FO pipes •Duplex FO filter

[ 18 ]

•Intake air heater •Ho rizontal exhaust outlet •Mixing elbow •Flexible mounts •Sea water filter •Kingston •Bilge pump •LO priming pump •LO evacuation pump •Drain separato r •Exhaust thermometer

•Flexible joint at T/C outlet •Flexible joint fo r piping •Exhaust silencer •Battery switch •Pipes fo r sea water, fuel oil

[ 19 ]

2000

6HYM-ETE MARINE

PROPULSION DIESEL ENGINE

M- rating 441kW (600mhp) L- rating 478kW (650mhp)

Dimensions Unit:mm Engine only / Front view

Engine only / Right side view 1556

1014

18

490

277

870

352

747

866 1133 790

119

267

With YXH160 gearbox / Right side view 2155

401

894

870

Combution system Aspiration Starting system Cooling system Dry mass Dimensions (L×W×H)

277

352

39

446

233

457

224

114

233

119

866

678

617

Specifications Model Number of cylinders Bore × stroke Displacement Rated output

No.1 265

With YXH160 gearbox / Rear view

• 6-cylinder, direct injection, heat exchanger cooling. • Twin-turbocharger + intercooler. • Available either with marine gear or without marine gear. • 4-valves per cylinder for higher combustion efficiency. • Conform to IMO emissions regulations. • Type approved by NK, ABS, BV, RINA.

39

446 No.6

524

524

760

265

1936

– Marine gear

mm lit. kW(hp)/rpm

kg mm

Performance curves

6HYM-ETE L-rating / M-rating 6 in-line 132.9 × 165 13.733 M : 441(600)/2100 L : 478(650)/2150 Direct injection Turbocharger + intercooler Electric starting motor (24V 6.0kW) Heat exchanger 1385(without marine gear) 1556×1014×1133

Marine gear specifications Engine model : 6HYM-ETE L-rating / M-rating Model YX-1 61L YXH-1 60 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.4 6 3.05 3.65 4.08 1.97 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 390 Dry weight 620

L-rating

M-rating

L/h 150

Fuel Consumption

100 50

50

tput

. ou

Max

ubic

ec

rin Ma

ve

cur

ut

outp

2500 2000

1500 1000 500

200

ine

Mar

urve

c ubic

c

e arin

e

urv

ic c

cub

M

0 N·m 3000

2000

4.55

300

100

Torque

ut

. outp

Max

400

200 100

Output

500

300

2500 Max.

0 kW 600

Output

500

0 N·m 3000

Fuel Consumption

100

0 kW 600

400

L/h 150

Torque x. Ma

t

tpu

ou

1500 1000 500

0 1000 1200 1400 1600 1800 2000 2200 2400 Speed of Crankshaft: rpm

ine

Mar

urve

ic c

cub

0 1000 1200 1400 1600 1800 2000 2200 2400

Accessories •Breather hose with fittings •Fresh water sub-tank •Alternato r 980W •2 pole wiring •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •Wiring harness •2 station instrument panel (C-type) •Installation parts •FPTO V-pulley •Double walled FO pipes •Duplex FO filter

[ 20 ]

•Intake air heater •Ho rizontal exhaust outlet •Mixing elbow •Flexible mounts •Sea water filter •Kingston •Bilge pump •LO priming pump •LO evacuation pump •Drain separato r •Exhaust thermometer

•Flexible joint at T/C outlet •Flexible joint fo r piping •Exhaust silencer •Battery switch •Pipes fo r sea water, fuel oil

[ 21 ]

6HYM-ETE MARINE

PROPULSION

S- rating 515kW (700mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view

1014 524

1556

490

18

277

870

352

39

747

866 1133 790

119

267

No.1

No.6

446

265

With YXH130 gearbox / Rear view

With YXH130 gearbox / Right side view 2076.5

401

lit. kW(hp)/rpm

kg mm

Marine gear specifications Engine model : 6HYM-ETE S-rating Model YXH-1 30 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.57 2.03 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 280 Dry weight

870

352

208

403

265 760

1825

– Marine gear

Performance curves L/h 150

Fuel Consumption

50 Output

500

1000

. ou

Max

ine

Mar

urve

ic c

cub

500 0 1000 1200 1400 1600 1800 2000 2200 Speed of Crankshaft: rpm

e urv

ic c

200 100

1500

t tpu

300

3.04

Torque t

tpu

. ou

2000

0 kW 600

400

N·m 3000 x 2500 Ma

100

ub ec

M

arin

0

Accessories •Breather hose with fittings •Fresh water sub-tank •Alternato r 980W •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •Wiring harness •2 station instrument panel (C-type) •Installation parts •FPTO V-pulley •Double walled FO pipes •Duplex FO filter

[ 22 ]

39

446

678

277

119 89

mm

6HYM-ETE S-rating 6 in-line 132.9 × 165 13.733 515(700)/2200 Direct injection Turbocharger + intercooler Electric starting motor (24V 6.0kW) Heat exchanger 1385(without marine gear) 1556×1014×1133

195 208

Specifications Model Number of cylinders Bore × stroke Displacement Rated output Combution system Aspiration Starting system Cooling system Dry mass Dimensions (L×W×H)

690 413

866

• 6-cylinder, direct injection, heat exchanger cooling. • Twin-turbocharger + intercooler. • Available either with marine gear or without marine gear. • 4-valves per cylinder for higher combustion efficiency. • Conform to IMO emissions regulations.

125.5

•Intake air heater •Ho rizontal exhaust outlet •Mixing elbow •Flexible mounts •Sea water filter •Kingston •Bilge pump •LO priming pump •LO evacuation pump •Drain separato r •Exhaust thermometer

•Flexible joint at T/C outlet •Flexible joint fo r piping •Exhaust silencer •Battery switch •Pipes fo r sea water, fuel oil

[ 23 ]

2400

6AYM-STE MARINE

PROPULSION

H- rating 485kW (659mhp) Dimensions Unit:mm

DIESEL ENGINE

With YX181 gearbox / Rear view

With YX181 gearbox / Right side view No.1 CYL.

No.6 CYL.

2364

520

1000

480

343

522

100

75 °

° 75

267

167

293.5

194.5

195 195 370

With YX180L gearbox / Rear view

No.1 CYL.

571

330 640

23 163 167

°

194.5

1343

70

560

260 393

266

– Marine gear

Performance curves L/h 150

N・m 5000

Fuel Consumption

Torque

100 4000

50 0 kW 500

3000

Output

2000 400

ur v rc we po er

200

0 800 1000 1200 1400 1600 1800 2000 2200 Engine speed : rpm

e

utp ut

1000 300

.o

Marine gear specifications Engine model : 6AYM-S TE Model YX-1 81 YX-1 80L YXH-240L Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.08 2.55 3.03 3.50 4.00 4.54 4.89 5.36 5.91 6.57 6.95 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 560 Dry weight 680 1240

260 393

Ma x

kg

480

293.5

100

0 900

Pr op ell

kW(hp)/rpm

1000

°

lit.

No.6 CYL.

2394

343

70

mm

6AMY-STE 6 in-line 155 × 180 20.379 H : 485(659)/1900 Direct injection Turbocharger + intercooler Electric starting motor (24V 7.0kW) Heat exchanger 2365

1609

With YX180L gearbox / Right side view

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler. • 4-valves per cylinder for higher combution efficiency. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by NK, ABS, BV, RINA, CCS. Specifications Model Number of cylinders Bore × stroke Displacement Rated output Combution system Aspiration Starting system Cooling system Dry mass

266

541

370

1100 1300 1500 1700 1900 Speed of Crankshaft: rpm

2100

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •2 station instrument panel (C-type) •Wiring harness •Air starting moto r •Flexible mounts (fo r engine) •FPTO V-pulley •Ho rizontal exhaust •Shallow sump

[ 24 ]

•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring •Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump

•Flexible joint fo r exhaust piping •Exhaust silencer •Battery switch •Alternato r 980W •Pipes fo r exhaust, sea water, fuel oil

[ 25 ]

6AYM-ETE MARINE

PROPULSION

H- rating 555kW (755mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view No.1 CYL.

1305 641 481

664

No.6 CYL.

1823 1000

343

480

946 1430.5

879

CRANK CENTER 817

171.5

279.5

22 384.5 167 551.5

194

177 175 962

1609

With YXH240L gearbox / Rear view

747

414

300 834

21 60°

302

1609

302

– Marine gear

810

Performance curves L/h 200

N・m 5000

Fuel Consumption

Torque

150 100

4000

50 0 kW 700

3000

Output

2000

600

1000

400

t

500

tpu

Marine gear specifications Engine model : 6AYM-ETE H Model YXH-240 YXH-240L Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 1.95 2.27 2.56 3.03 3.4 8 4.89 5.36 5.91 6.57 6.95 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 645 Dry weight 1240

266

ou

kg

480

194.5 795

300 200

er

ell

op

Pr

e ow

0 800 1000 1200 1400 1600 1800 2000 2200 Engine speed : rpm

ve

ur

rc

x.

kW(hp)/rpm

1000

194

Ma

lit.

No.6 CYL.

2570

343 279.5

60°

mm

6AMY-ETE H 6 in-line 155 × 180 20.379 H : 555(755)/1840 Direct injection Turbocharger + intercooler Electric starting motor (24V 7.0kW) Heat exchanger 2365

With YXH240L gearbox / Right side view No.1 CYL.

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler. • 4-valves per cylinder for higher combution efficiency. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by NK, ABS, BV, RINA, CCS. Specifications Model Number of cylinders Bore × stroke Displacement Rated output Combution system Aspiration Starting system Cooling system Dry mass

266

194.5

p

100 0 900

1100 1300 1500 1700 1900 Speed of Crankshaft: rpm

2100

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •2 station instrument panel (C-type) •Wiring harness •Air starting moto r •Flexible mounts (fo r engine) •FPTO V-pulley •Ho rizontal exhaust •Shallow sump

[ 26 ]

•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring •Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump

•Flexible joint fo r exhaust piping •Exhaust silencer •Battery switch •Alternato r 980W •Pipes fo r exhaust, sea water, fuel oil

[ 27 ]

6AYM-ETE MARINE

PROPULSION

M- rating 610kW (829mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view

1305

1430.5

879

2000

With YXH240 gearbox / Rear view

With YXH240 gearbox / Right side view 2474 651

167

313

194.5 535.5

266 1609

– Marine gear

Performance curves L/h 200

N・m 5000

Fuel Consumption

Torque

150 100

4000

50 0 kW 700

3000

Output

2000

600

1000

tpu ou

400

t

500

x.

Marine gear specifications Engine model : 6AYM-ETE M Model YXH-240 YXH-240L Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 1.95 2.27 2.56 3.03 3.4 8 4.89 5.36 5.91 6.57 6.95 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 645 Dry weight 1240

195 195 586

300 200

er

ell

op

Pr

e ow

0 800 1000 1200 1400 1600 1800 2000 2200 Engine speed : rpm

ve

ur

rc

Ma

kg

194

608

19

65 °

lit. kW(hp)/rpm

480

65°

mm

6AMY-ETE M 6 in-line 155 × 180 20.379 M : 610(829)/1900 Direct injection Turbocharger + intercooler Electric starting motor (24V 7.0kW) Heat exchanger 2365

1000 279.5

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler. • 4-valves per cylinder for higher combution efficiency. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by NK, ABS, BV, RINA, CCS. Specifications Model Number of cylinders Bore × stroke Displacement Rated output Combution system Aspiration Starting system Cooling system Dry mass

343

p

100 0 900

1100 1300 1500 1700 1900 Speed of Crankshaft: rpm

2100

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •2 station instrument panel (C-type) •Wiring harness •Air starting moto r •Flexible mounts (fo r engine) •FPTO V-pulley •Ho rizontal exhaust •Shallow sump

[ 28 ]

•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring •Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump

•Flexible joint fo r exhaust piping •Exhaust silencer •Battery switch •Alternato r 980W •Pipes fo r exhaust, sea water, fuel oil

[ 29 ]

6AYM-GTE MARINE

PROPULSION

L- rating 670kW (911mhp) Dimensions Unit:mm

DIESEL ENGINE

Engine only / Front view

Engine only / Right side view [Shallow sump] 2000

1330.5

879

1305

With YXH240 gearbox / Rear view

With YXH240 gearbox / Right side view 2474 651

343

480

1000 279.5

1609

313

– Marine gear

Performance curves L/h 250 200 150 100 50 0 1000 kW 700

N・m 5000

Fuel Consumption

Torque

4000 1200

1400

1600

1800

2000

3000

Output 2000

600 1000

x. o

utp

ut

500

0 800 1000 1200 1400 1600 1800 2000 2200 Engine speed : rpm

Ma

400

cu

rv

e

300

er

3.4 8

ell

Marine gear specifications Engine model : 6AYM-GTE Model YXH-240 Type Hydraulic multi-disc clutch Reduction ratio (Ahead) 2.27 2.56 3.03 1.95 Direction of rotation (propeller shaft) Clockwise o r counterclockwise kg 645 Dry weight

266

194.5 535.5

586

200

op

kg

195 195

6AMY-GTE 6 in-line 155 × 180 20.379 L : 670(911)/1938 Direct injection Turbocharger + intercooler Electric starting motor (24V 7.0kW) Heat exchanger 2365(without marine gear)

Pr

lit. kW(hp)/rpm

608

19

65 °

mm

194

65°

Specifications Model Number of cylinders Bore × stroke Displacement Rated output Combution system Aspiration Starting system Cooling system Dry mass

167

• 6-cylinder, direct injection, heat exchanger cooling. • Turbocharger + intercooler. • 4-valves per cylinder for higher combution efficiency. • Available either with marine gear or without marine gear. • Conform to IMO emissions regulations. • Type approved by NK, ABS, BV, RINA, CCS.

100 0 900

1100

1300 1500 1700 Engine Speed: rpm

1900

2100

Accessories •Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel fo r wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual

•YX gearbox •Remote control head & cable •2 station instrument panel (C-type) •Wiring harness •Air starting moto r •Flexible mounts (fo r engine) •FPTO V-pulley •Ho rizontal exhaust •Shallow sump

[ 30 ]

•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring •Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump

•Flexible joint fo r exhaust piping •Exhaust silencer •Battery switch •Alternato r 980W •Pipes fo r exhaust, sea water, fuel oil

[ 31 ]

JH series (Life Boat Engines) MARINE

PROPULSION

18.4~24.3kW (25~33mhp)

DIESEL ENGINE

• Comply with SOLAS'96. • Engine keeps on running after a 360 degree roll. • Engine can run at least five minutes in water up to centerline of crankshaft. • Engine is designed to withstand a free fall (fitted on a life boat). Specifications Model Number of cylinders Bore × stroke Displacement Rated output Max. output Combution system Aspiration Starting system Cooling system Marine gear Dry weight

mm lit. kW(PS)/rpm kW(PS)/rpm

kg

MARINE

3JH30A 3JH25A 3 82 × 86 1.363 22.1(30)/2900 18.4(25)/3200 24.3(33)/3000 20.2(27.5)/3300 Direct injection Nutural aspirated Electric starting motor (12V 1.8kW) Heat exchanger / Keel cooling Mechanical 187

AUXILIARY

DIESEL ENGINE

Marine gear specifications Engine model : JH Model KM35P1 Type Hydraulic multi-disc clutch Reduction ratio Ahead: 2.36 Astern: 3.1 6 Direction of rotation (propeller shaft) Clockwise o r counterclockwise Dimensions Unit:mm 278 190.5

543

265

Right side view

237.5

4.5 31.5

65

33.5

680

309.1

442.5

Rear view

183.8 180.6

93 95 480

701.3 730.1

28.8

Accessories •Breather hose with fittings •Evacuation hand pump •Charging alternato r •Instrument panel fo r wheel house (B-type)

•Kingston cock •Wiring harness 4m •Half coupling (rough bo re type) •Standard spare parts •Standard tool kit •Operation manual

[ 32 ]

[ 33 ]

4CHL series MARINE

AUXILIARY

DIESEL ENGINE

38~62hp /1500~1800rpm 30~50kVA (24~40kW)

Dimensions Unit:mm Engine only (4CHL-TN) Front view

Left side view 800

1089

400

400

300

402

196

387

287 325

+0.127 0

φ352.425 +0.02 φ392

+0.08

182

φ409.575 約290

192

94 254 287 381

172

536

691

21

1191

700

810

110

11

137.5 64.5

232 295

140 215

125

75

Generator set dimensions for your reference Unit:mm Generator set dimensions shown below depend on generator model

• 4-cylinder, direct injection. • Natu ral aspirated or turbocharged. • Type approved by BV.

Frequency Combution system Aspiration Dry weight (Engine only) Dry weight (Gen. set)

lit. rpm hp kVA(kW) Hz

kg kg

38 30(24)

50 40(32)

60 50 Direct injection Nutural aspiration 500 960

A

4CHL-TN

1500

1800

50 40(32)

62 50(40)

50

60

F

Continuous rated output Applicable generator capacity

mm

4CHL-N In-line 4 105 × 125 4.33 1800 1500

Left side view B

G（for Removing Piston）

Specifications Model Number of cylinders Bore × stroke Displacement Continuous rated engine speed

Front view

E

Exhauust Turbocharger 520 1010

Model 4CHL-N 4CHL-TN

D

A 1555 1567

B 922 922

D 1350 1350

E 522 522

F 473 473

G 1164 1164 – Generator

Accessories •Instrumental panel (attached to engine) •Cooling system : Rubber impeller type sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat fo r fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Single type) •Fuel system : Paper filter type fuel strainer / Drain separato r to be mounted on vessel •Turbocharging system : Exhaust gas outlet expansion joint from engine (TN) •Electrical equipment : Starter moto r (DC24V) 4.0kW / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder (N) / Exhaust gas at inlet of turbocharger (TN) / Cooling water outlet / Lubrication oil at cooler inlet

[ 34 ]

•Cooling system : Kingston cock •Lubrication system : Manual priming pump / Inlet and outlet joint fo r semi dry sump •Fuel system : Primary fuel strainer to be mounted on vessel •Electrical equipment : Alternato r (DC24V600W) •Generator (and common bed) : Taiyo o r Stamfo rd •Thermometer : Lubrication oil at cooler outlet •Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer •Compressed air starting device •Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring

[ 35 ]

6CHL series MARINE

AUXILIARY

DIESEL ENGINE

62~120hp /1500~1800rpm 50~100 kVA (40~80kW)

Dimensions Unit:mm Engine only (6CHL-HTN) Front view

Left side view 420

300 111 189

1378 691

387 214.5

461

536 287 325 36 288

192

281 100 381

25

750

860 1241 691 (for Removing Piston)

110

522 230

21 73

233 295 404 942

33

884.5

Generator set dimensions for your reference Unit:mm

• 6-cylinder, direct injection. • Natural aspirated o r turbocharged. • Type approved by BV.

Front view

Left side view

B

A

mm lit. rpm

6CHL-TN

6CHL-HTN

1500

1500

1800

1800

Continuous rated output hp Applicable kVA(kW) generator capacity

62 74 74 100 100 120 50(40) 60(48) 60(48) 80(64) 80(64) 100(80)

Frequency Combution system Aspiration

Hz

50 50 60 60 Direct injection Nutural Exhauust aspiration Turbocharger

Exhauust Turbocharger with intercooler

Dry weight (Engine only) Dry weight (Gen. set)

kg

625 1170

675 1340

kg

645 1310

50

G（for Removing Piston）

HTN is not Type approved.

6CHL-N In-line 6 105 × 125 6.494 1500 1800

F

Specifications Model Number of cylinders Bore × stroke Displacement Continuous rated engine speed

Generator set dimensions shown below depend on generator model

60 E

Model 6CHL-N 6CHL-TN 6CHL-HTN

D

A 1885.5 1945.5 1965.5

B 942 942 942

D 1650 1700 1700

E 522 522 522

F 474 474 474

G 1165 1165 1165 – Generator

Accessories •Instrumental panel (attached to engine) •Cooling system : Rubber impeller type sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat fo r fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Single type) •Fuel system : Paper filter type fuel strainer / Drain separato r to be mounted on vessel •Turbocharging system : Exhaust gas outlet expansion joint from engine (TN, HTN) •Electrical equipment : Starter moto r (DC24V) 4.0kW / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder (N) / Exhaust gas at inlet of turbocharger (TN, HTN) / Cooling water outlet / Lubrication oil at cooler inlet [ 36 ]

•Cooling system : Kingston cock •Lubrication system : Manual priming pump / Inlet and outlet joint fo r semi dry sump •Fuel system : Primary fuel strainer to be mounted on vessel •Electrical equipment : Alternato r (DC24V600W) •Generator (and common bed) : Taiyo o r Stamfo rd •Thermometer : Lubrication oil at cooler outlet •Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer •Compressed starting device •Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring

[ 37 ]

4HAL2 series MARINE

AUXILIARY

DIESEL ENGINE

98~183hp /1200~1800rpm 80~150kVA (64~120kW)

Dimensions Unit:mm Engine only Front view

Left side view No.4 CYL.

No.1 CYL. 1061.5 526.5

1429.5 535

434

510

485.5

110

276.5

232

R294

1244

229

461

1196

735

756

111.5

313

121

Generator set dimensions for your reference Unit:mm Generator set dimensions shown below depend on generator model

• 4-cylinder, direct injection. • Type approved by BV, GL.

Frequency Combution system Aspiration Dry weight (Engine only) Dry weight (Gne. set)

hp kVA(kW) Hz

kg kg

98 80 (64)

121 100 (80)

4HAL2-TN

1800 1200

1500

1800

122 157 130 100 (104) (80)

156 125 (100)

183 150 (120)

50

60

60 50 60 50 Direct injection Exhaust Turbocharger 1030 1785 1855 1855 1845

C

lit. rpm

4HAL2-TN1 In-line 4 130 × 165 8.76 1200 1500

A

G（for Removing Piston）

Continuous rated output Applicable generator capacity

mm

Left side view B

F

Specifications Model Number of cylinders Bore × stroke Displacement Continuous rated engine speed

Front view

E

1855

1855

Model 4HAL2-TN1 4HAL2-TN

D

C B A 2070.5 1116.5 1264 2070.5 1116.5 1264

D 1600 1600

E 559 559

F 529 529

G 1312 1312 – Generator

Accessories •Instrumental panel (attached to engine) •Cooling system : Sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat fo r fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Single type) / Manual priming pump •Fuel system : Paper filter type fuel strainer / Drain separato r to be mounted on vessel •Turbocharging system : Exhaust gas outlet expansion joint from engine •Electrical equipment : Starter moto r (DC24V) 5.5kW / Alternato r (DC24V600W) / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder / Cooling water outlet / Lubrication oil at cooler inlet

[ 38 ]

•Cooling system : Kingston cock •Lubrication system : Inlet and outlet joint fo r semi dry sump •Fuel system : Primary fuel strainer to be mounted on vessel •Generator (and common bed) : Taiyo o r Stamfo rd •Thermometer : Exhaust gas at inlet of turbocharger / Lubrication oil at cooler outlet •Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer •Compres sed air starting device •Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring

[ 39 ]

6HAL2 series MARINE

AUXILIARY

DIESEL ENGINE

122~414hp /1200~1800rpm 100~350kVA (80~280kW)

Dimensions Unit:mm Engine only (6HAL2-TN, -HTN, -DTN) Front view

Left side view No.6 CYL.

No.1 CYL.

1795

1115 515.5

599.5

442

870

483

330

R370

465

292

1331

783

866

171.5

276.5

108

Generator set dimensions for your reference Unit:mm

Continuous rated output hp kVA(kW) Applicable generator capacity

122 156 163 204 244 217 299 360 271 346 414 100 125 130 170 200 180 250 300 225 290 350 (80) (100) (104) (136) (160) (144) (200) (240) (180) (232) (280)

Frequency Combution system Aspiration

Hz

60 50 60 50 60 Direct injection Nutural Exhaust aspiration Turbocharger

Dry weight (Engine only) Dry weight (Gen. set)

kg

mm lit.

kg

1380 2220

60

50

60

60

50

A

C

rpm

6HAL2-N 6HAL2-TN 6HAL2-HTN 6HAL2-DTN In-line 6 130×165 13.14 1200 1500 1200 1500 1800 1200 1500 1800 1200 1500 1800

Left side view B

1395 1410 1420 2330 2380 2380 2670 2720 2720 2790 2820 2820

J.BOX

E

60

Exhaust Turbocharger with intercooler

G（for Removing Piston）

Specifications Model Number of cylinders Bore × stroke Displacement Continuous rated engine speed

Front view

F

• 6-cylinder, direct injection. • Natural aspirated o r turbocharged. (with intercooler) • Type approved by NK, BV, GL.

Generator set dimensions shown below depend on generator model

Model 6HAL2-N 6HAL2-TN 6HAL2-HTN 6HAL2-DTN

D

A 2388.5 2498.5 2573.5 2683.5

B 1163.5 1163.5 1163.5 1163.5

C 1344 1410 1410 1410

D 2100 2100 2200 2200

E 495 527 527 527

F 544 544 544 544

G 1327 1327 1327 1327 – Generator

Accessories •Instrumental panel (attached to engine) •Cooling system : Sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat fo r fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Tandem switch type) / Manual priming pump •Fuel system : Paper filter type fuel strainer / Drain separato r to be mounted on vessel •Turbocharging system : Exhaust gas outlet expansion joint from engine •Electrical equipment : Starter moto r (DC24V) 6.0kW / Alternato r (DC24V600W) / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder / Cooling water outlet / Lubrication oil at cooler inlet

[ 40 ]

•Cooling system : Kingston cock •Lubrication system : Inlet and outlet joint fo r semi dry sump •Fuel system : Primary fuel strainer to be mounted on vessel •Generator (and common bed) : Taiyo o r Stamfo rd •Thermometer : Exhaust gas at inlet of turbocharger (TN, HTN, DTN) / Lubrication oil at cooler outlet •Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer •Compressed air starting device •Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring

[ 41 ]

6AYL series MARINE

AUXILIARY

DIESEL ENGINE

480~668hp /1500~1800rpm 400~562.5kVA (320~450kW)

Dimensions Unit:mm Engine only Front view

Left side view NO.6CYL.

1342

2030 1000

516.5

701

279.5

513.5 343

518.5

22 384.5 167 551.5

1430.5

817

879

946

400

641 481

93.5

177 175

214

731

Generator set dimensions for your reference Unit:mm

• 6-cylinder, direct injection. • Turbocharged with intercooler. • Type approved by NK, ABS, BV, RINA, CCS.

Front view

1500

1800

Continuous rated output hp Applicable kVA(kW) generator capacity

480 400(320)

596 500(400)

668 562.5(450)

Frequency Combution system Aspiration Dry weight (Engine only) Dry weight (Gen. set)

50 60 Direct injection Exhaust Turbocharger with intercooler 2435 4120 4300 4780 5300

lit.

Hz

kg kg

60

C G（for Removing Piston）

6AYL-ET

rpm

A

B

6AYL-ST In-line 6 155 × 180 20.379 1800

mm

Left side view

F

Specifications Model Number of cylinders Bore × stroke Displacement Continuous rated engine speed

Generator set dimensions shown below depend on generator model

D

E

Model 6AYL-ST 6AYL-ET

B A 3042.5 1346 3389.5 1346

C 1508 1508

D 2380 2930

E 738 738

F 619 619

G 1565 1565 – Generator

Accessories •Instrumental panel (attached to engine) •Cooling system : Sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat fo r fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Tandem switch type) / Manual priming pump •Fuel system : Paper filter type fuel strainer / Drain separato r to be mounted on vessel •Turbocharging system : Exhaust gas outlet expansion joint from engine •Electrical equipment : Starter moto r (DC24V) 7.0kW / Alternato r (DC24V600W) / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder / Cooling water outlet / Lubrication oil at cooler inlet

[ 42 ]

•Cooling system : Kingston cock •Lubrication system : Inlet and outlet joint fo r semi dry sump / Large wet sump •Fuel system : Primary fuel strainer to be mounted on vessel •Generator (and common bed) : Taiyo o r Stamfo rd •Thermometer : Exhaust gas at inlet of turbocharger / Lubrication oil at cooler outlet •Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer •Compres sed starting device •Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring

[ 43 ]