and move the Choke lever to START position. 2. Move the switch to its ON position, then the momentary start position to electrically start the generator. 3. Pull the ...
... Phone: 903.498.3363 Fax: 903.498.3364 Email: [email protected] ... The lamp housing is weatherproof and co
Made in America Compliant. The SPG12KW-120 Solar Power Generator from Larson Electronics is a towable power generation u
Install in accordance with the manufacturer's instructions. 8) Do not install near any ...... and nudity present within
Jan 22, 2001 - This operating manual includes basic operating .... âNote to CATV system installer: This reminder is pr
replacement of the plug is required, be sure the service technician has .... ENERGY STAR® Program Information. Products
MODEL. CD-BA2100. MINI COMPONENT SYSTEM. Thank you for purchasing
this SHARP product. To obtain the best performance from this product,.
Instalacion E Instrucciones de Seguridad. Modelos ..... capability. The IN1408 is a
powerful system integration tool that makes it easy to connect a ... signals from
computer sound cards with SPDIF digital outputs and DVD players with coaxial.
Before using the projector, please read this operation manual carefully. There are
two important reasons for prompt warranty registration of your new SHARP ...
THIS UNIT IS A CLASS 1 LASER PRODUCT. USE OF CONTROLS OR .... 21) Safety Check - Upon completion of any service or repai
Jan 22, 2001 - While VCR input mode is selected, the BLUE SCREEN will not be shown on your TV even if the. BLUE SCREEN i
information and copier operation)" and operation manuals for any optional ...
manual, please contact your nearest SHARP Service Department. ○ This
product ...
ENGLISH. MODEL. CD-DH950P. MINI COMPONENT SYSTEM. OPERATION
MANUAL. CD-DH950P Mini Component System consisting of CD-DH950P (main
unit) and .... 2. AUDIOIN. 12345. 45321. MINI COMPONENT SYSTEM. OPEN /
CLOSE ... Correction of defects, in the manner
9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: ... Explosion Proof LED Strobe Light - 12-36 Volts DC - 141 C
... 903.498.3363 Fax: 903.498.3364 Email: [email protected] ... strength copper-free aluminum alloy with a bak
aluminum housing is fully factory sealed and includes an integrated inspection hole for easy access to the splice compar
This unit is bench laboratory DC power supply which incorporate 4 pieces of 3%
digital display for two monitoring ... LODESTAR. :.a 3 L1 _ :2 a L: \NT FDVM!
This illustrations printed in this operation manual are for the model DK-A10.
Accessories. Please confirm that the following accessories are included. Note:
Only ...
symbol on your product or in this manual, look for one of the following ..... 1400.
P42B0010A2-01. 6.7. 1500. 8.1. 1800. P42B0015A2-01. 9.0. 2000. 10.4. 2350.
OPERATION MANUAL. EL-509W ... In this manual, key operations are described
as follows: To specify ex : ..... Data items exceeded 100 in the statistics mode.
not installed and used in accordance with the instruction manual, may cause
harmful ... how to inspect and carry out maintenance on the digital copier. • how
to ...
May 31, 2000 - âNote to CATV system installer: This reminder is provided to call the CATV system installer's attention
To aid in reporting this microwave oven in case of loss or theft, please record
below ... (b) Do not place any object between the oven front face and the door or
...
1. Attach the light head to the mast and tighten the hand screw to secure it in place.
Rotate each light head as needed. Each light head can be adjusted independently by loosening the bolts on either side of the light. Retighten these bolts once the light is in your desired position.
2. Wheel the cart to a flat level surface where the unit will be operating.
Remove the locking pin at the base of the handle for maneuvering the tower. Replace this locking pin once the tower is in position to hold the handle.
3. Extend each outrigger by loosening the T handles on the bottom of the cart holding them in place.
Pull each outrigger out until it stops. Tighten all T-handles to secure the outriggers.
Page 2 of 5
Pull the pin on the jack to rotate it vertical to the ground.
Turn the hand crank on each jack clockwise to extend it and level the cart. There are four outriggers that are used to help stabilize the tower when extended.
Once the winch comes to a stop, the mast is fully elevated and ready to be powered by its generator.
4. Locate the self-locking hand winch on the back of the unit to raise the mast. A clockwise rotation will raise the mast to its full height.
5. Plug the twist lock cord into the AC 120V/240V side of the generator. This enables power to the light heads on top of the mast.
Page 3 of 5
Generator: The generator contains an electric start as well as a secondary pull cord for manually starting the unit.
1. Ensure there’s an adequate amount of fuel in the unit before running. Turn the fuel valve to ON position and move the Choke lever to START position.
2. Move the switch to its ON position, then the momentary start position to electrically start the generator.
3. Pull the cord to mechanically start the generator while the switch is positioned ON.
4. After a few seconds, reopen the CHOKE and the generator will power the tower.
5. Move the switch to its OFF position to power down the unit.
6. Close the fuel valve when storing the unit.
Page 4 of 5
Lowering the Mast:
3. Loosen the T handles under the cart and return each outrigger jack to its UP position where the bottoms face each other. 1. When the job is complete, power down the generator.
2. Turn the hand winch counter-clockwise to lower the mast until the light head is no longer supported by the winch cable.
Push each jack back in. Tighten the hand screws on the bottom to hold them in place.
4. Unlatch the handle to move the tower freely. Secure the handle using the locking pin once positioned.
![operation manual - Larson Electronics [PDF]](https://m.moam.info/img/260x300/operation-manual-larson-electronics-pdf_6479f39a098a9e144d8b4691.jpg)
