fitted to Toyota 100 series Landcruiser, Mitsubishi Rosa and Isuzu engines. Now
these pumps ... Fitted to Nissan TD27Ti QD32Ti and Isuzu 4JG2. Exchange ...
Parts Catalogue
For all your Diesel Fuel Injection, Turbocharger & Auto Electrical Requirements
4 Nen Street Oamaru www.jep.co.nz
Phone 03 434 8967 Fax 03 434 8389 E Mail
[email protected]
Welcome to our parts catalogue, this is a work in progress and new products will be added from time to time. E mail or call for the latest prices. To use this catalogue click on the bookmark tab on the left. click on the product range you want to look at and you will be taken to the start of the range. Alternatively click on the pages tab and scroll through the pages Can’t find what your looking for? Give us a call or E mail us and we will happy to assist with your enquiry.
South Islands only officially authorised and factory equipped Denso V3 & V4 service dealer 2L-TE, 1KZ-TE, 5L-E, 3C-TE & 1HD-FTE As many of you know J E Paisley have completed the factory training and invested in the service tools and test equipment necessary to fully overhaul and test Denso ECD V3 resistor and ROM pumps fitted to Toyota 2L-TE, 1KZ-TE, 5L-E and 3C-TE engines and ECD V4 pumps fitted to Toyota 100 series Landcruiser, Mitsubishi Rosa and Isuzu engines. Now these pumps are able to be stripped, cleaned, re-kited and tested at realistic prices.
V3 Resister pump
V3 ROM pump
V4 pump
DensoV4 Needle valve replacement J E Paisley is the only Denso Authorized V4 needle valve replacement center in New Zealand. We can now economically replace worn needle valves with genuine Denso parts. Previously this had necessitated the complete and expensive replacement of the hydraulic head assembly due to the close fitting tolerances of the needle valve. (.001mm)
Exchange pumps and injectors Available , ring us with the vehicle model and engine type
Common rail pump O/haul and Testing
Hartridge AVM2-PC test bench Due to the demands of our Capricorns customers J E Paisleys have commissioned the latest Hartridge AVM2 test bench. This new bench along with our Bosch 815 bench allows the accurate setting of all major makes of fuel injection equipment. Both these benches are subject to annual factory audits by the leading manufactures of fuel injection equipment to ensure their accuracy. The AVM2-PC capable of flow and high pressure testing of common rail pumps.
Denso HP3
Bosch CP1
Common rail injectors tested using Bosch EPS200 and Hartridge IFT-C test equipment
D4 Washer kits
Zexel COVEC pumps Fitted to Nissan TD27Ti QD32Ti and Isuzu 4JG2 Exchange pump for Td27 and QD32 available
A makes and models of inline and rotary fuel pumps serviced Exchange pumps available
All makes of injectors serviced and tested
Petrol injectors cleaned and tested
Two spring injectors fully serviced
Pintle type injector
Gardner injectors tested and serviced
Leyland injectors tested and serviced
Most common injector sealing washers available individually or in kits
All makes of turbo's and sold serviced Ring us for your requirements
VE type pump timing gauges
Our most popular timing gauge screws directly into the head plug
90 degree timing adapter
Why you should time before and after you remove the injector pump. The cold hard reality is that timing specifications for some of the Japanese import vehicles we work on are simply not readily available. By checking the timing before you remove the pump or doing a cam belt, will give you a fall back position when you refit the pump or cam belt and you can’t find a spec for that engine. It also gives you a reference or starting point if the owner complains because the vehicle doesn't perform like it used to. It may surprise some to learn that there can be three or four different timing specifications for the same engine depending on what country it was destined for. Although these different settings may appear minor, they can and will have an influence on engine performance. Time before and after.
Racor Fuel Filters / water traps
Racor 230R can offer near 100% water removal. These units fitted with a warning buzzer should be installed as close to the tank as possible in order to maximise their protection against water entering the system. Capable of retaining 58 mls of water (to the probe tip) allowing the operator to shut down the engine preventing serious damage. Flow
Racor 500FG also offering near 100% water removal. fitted with a warning buzzer this unit should be installed as close to the tank as possible in order to maximise their protection against water entering the system. Capable of retaining 110 of water (to the probe tip) respectively , allowing the operator to shut down the engine preventing serious damage. (Used by the US coast guard} Flow
Larger units and dual head models available
Fuel Filters
Electric fuel pump/filter assembly 12volt electric lift pump with integral pressure regulator set to 10 psi.
Bulk Tank Filters
Bulk tank filter with drain
Latest Racor water absorbing fuel filter. The Racor dispensing filters start protecting engines at the source, removing virtually 100% of contaminants from diesel or petrol, including water, dirt, rust and biological micro -organisms. Racor fuel dispensing filters offer protection down to 10 microns. Flow rates range from 15 to 100 GPH with a maximum operating pressure 100 psi These filters feature a super-absorbent, chemically treated media with two unique features: 1/ the filter media absorbs 25 times its weight in water and locks it in. It is an effective barrier against free and emulsified water. 2/ as the media swells with water removed from the fuel, it gradually reduced the flow rate signalling the need to replace the filter.
Filter heads and Non-return valves
Replacement head for Isuzu Mitsubishi. Will fit Nissan when used with a Z304 filter element
Replacement Toyota filter head
Universal bulk tank filter head
Alloy one way valves available in 8mm — 10mm and 13mm These valves should only be fitted after the main filter too prevent dirt entering valve.
One way valve with filter screen suitable for installation before the main filter, available in 8mm and 10mm Can be disassembled and cleaned.
Toyota 12mm removable tails
Nissan 8mm Tails
Toyota 8mm Tails
Sedimentors
Parts available separately
Banjo bolt kit metric
Banjo kit metric
Hose sleeve kit
Fuel pipe fittings
Fuel pipe fittings
Feed pumps
Electric pumps in both 12 and 24 volts
Full range of glow plugs stocked Can’t find what your looking for? Give us a call
