Hood Assembly, 22HP Yanmar CE. 2. Nut Assembly, 3/8-16 Cover Retaining. 3.
Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop. Instruction Sheet, 2261/73 CE ...
2261ADC Articulator 2273ADC Articulator Parts Manual Manual Part #: Man-2261ADC
LASTEC
7865 N County Road 100E Lizton, Indiana 46149
Phone (317) 892-4444 Fax (317) 892-4188 www.lastec.com
8
Lastec, 2009
Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any photographic, electronic, mechanical or other means or used in any information storage and retrieval system without written permission from Lastec, Inc. 7865 N. County Road 100E Lizton, IN 46149
Table of Contents SECTION 1 1.1 1.2 1.3 1.4
Table of Contents
1-1
DRIVE SYSTEM
2-1
Seat Assembly ........................................................................................................... 2-2 Roll-Over Protection System (ROPS) ....................................................................... 2-4 Rocker Assembly (Serial # 2130406 and prior) ........................................................ 2-6 Rocker Assembly, 61” Deck (Serial # 2140406 and later) ....................................... 2-8 Rocker Assembly, 73” Deck ................................................................................... 2-10 Left Rocker Deck Lift Assembly, 61” Deck ........................................................... 2-12 Right Rocker Deck Lift Assembly, 61” and 73” Decks.......................................... 2-14 Left Rocker Deck Lift Assembly, 73” Deck ........................................................... 2-16 Rocker Wheel Assembly ......................................................................................... 2-18 Wheel Yoke Assembly ............................................................................................ 2-20 Wheel Assembly, 13 x 6.50 x 6............................................................................... 2-22 Control Box Assembly (Serial # 24331106 and prior)............................................ 2-24 Control Box Assembly (Serial # 24331106 and 35471009) ................................... 2-26 Control Box Assembly ............................................................................................ 2-28 Diesel Throttle Cable Assembly.............................................................................. 2-30 Hand Contol Assembly............................................................................................ 2-32 Pedal Assembly (Optional as of serial #26270307) ................................................ 2-34 Throttle Assembly (Deleted after Serial # 24321106) ............................................ 2-36 Front Deck Lift Rod Assembly (Serial #24311106 and prior)................................ 2-38 Front Deck Lift Rod Assembly (Serial #24331106 and later) ................................ 2-40 Emergency Brake Assembly ................................................................................... 2-42 Rear Deck Lift Rod Assembly ................................................................................ 2-44 Framework............................................................................................................... 2-46 Pull Bar Assembly................................................................................................... 2-48 Striping Kit (Optional) ............................................................................................ 2-50
SECTION 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8
GENERAL INFORMATION
How To Use The Parts List ....................................................................................... 1-2 Torque Values ........................................................................................................... 1-3 Decals ........................................................................................................................ 1-4 Hardware Kit (CE Only) ........................................................................................... 1-8
SECTION 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25
Section-Page
HYDRAULIC SYSTEM
3-1
Hydraulic Layout Diagram........................................................................................ 3-2 Hydraulic Pump Assemblies ..................................................................................... 3-4 Hydraulic Motor, Right ............................................................................................. 3-6 Hydraulic Motor, Left ............................................................................................... 3-8 Brake Assembly....................................................................................................... 3-10 Hydraulic Filter Assembly ...................................................................................... 3-12 Hydraulic Tank Assembly....................................................................................... 3-14 Hydraulic Idler......................................................................................................... 3-16
Lastec//042315
3
Table of Contents SECTION 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15
4
ENGINE & ELECTRICAL
4-1
Fuel Tank (Serial # 25610207 and prior) .................................................................. 4-2 Fuel Tank Assembly.................................................................................................. 4-4 Fuel System ............................................................................................................... 4-6 Engine Assembly....................................................................................................... 4-8 Clutch Assembly ..................................................................................................... 4-10 Clutch Guard ........................................................................................................... 4-12 Air Cleaner .............................................................................................................. 4-14 Fuel Separator Assembly......................................................................................... 4-16 Motor Mount ........................................................................................................... 4-18 Engine Assembly Mount ......................................................................................... 4-20 Idler, Deck Drive ..................................................................................................... 4-22 Radiator Assembly .................................................................................................. 4-24 Exhaust System ....................................................................................................... 4-26 Battery Box Assembly............................................................................................. 4-28 Electrical Harness ................................................................................................... 4-30
SECTION 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14
Section-Page
61” MOWER DECK
5-1
Deck Framework ....................................................................................................... 5-2 Deck 1 Hardware (Serial # 2860806 and later) ......................................................... 5-4 Deck 1 Hardware (Serial # 2850806 and prior) ........................................................ 5-6 Deck 2 Hardware....................................................................................................... 5-8 Rear Discharge Baffle Assembly ............................................................................ 5-10 Deck 3 Hardware..................................................................................................... 5-12 Optional Mulching Kit ............................................................................................ 5-14 Double Pulley Spindle (5/14 and later) ................................................................... 5-16 Spindle Housing ..................................................................................................... 5-18 Double Pulley Spindle (Prior to 5/14) ..................................................................... 5-20 Spindle Housing ...................................................................................................... 5-22 Tensioner Assembly ................................................................................................ 5-24 Grass Chute ............................................................................................................. 5-26 Rear Anti-scalp Roller (Prior to 5/14) ..................................................................... 5-28
Lastec//042315
Table of Contents
Table of Contents SECTION 6 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 6.11 6.12 6.13
73” MOWER DECK
6-1
Deck Framework ....................................................................................................... 6-2 Deck 1 Hardware....................................................................................................... 6-4 Deck 2 Hardware....................................................................................................... 6-6 Deck 3 Hardware....................................................................................................... 6-8 Double Pulley Spindle, Decks 1 and 3 (8/14 and later) ......................................... 6-10 Spindle Housing, Decks 1 and 3 (8/14 and later).................................................... 6-12 Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14) ............................................ 6-14 Spindle Housing ...................................................................................................... 6-16 Tensioner Assembly ................................................................................................ 6-18 Deck 2, Double Pulley Drive Spindle (8/14 and later)............................................ 6-20 Deck 2, Double Pulley Drive Spindle (Prior to 8/14) ............................................. 6-22 Grass Chute ............................................................................................................. 6-24 Rear Anti-scalp Roller (Prior to 8/14) ..................................................................... 6-26
SECTION 7
5
Section-Page
INDEX
7-1
Lastec//042315
Table of Contents
1
SECTION 1 GENERAL INFORMATION
Mower//042315
1-1
1 1.1
General Information How To Use The Parts List
How To Use The Parts List
Use the table of contents or part number index to locate the part you need.
Go to the appropriate section and locate the part in the table and illustration.
Parts shown indented under another part are included with that part. IMPORTANT: Assemblies marked with a diamond () are non-saleable and all the parts shown as included need to be purchased separately.
See the sample table below. Sample Assembly A01111 includes part F02222-22 and subassembly A03333. The diamond () indicates that assembly A01111 is non-saleable and all the parts shown as included need to be purchased separately. Subassembly A03333 includes parts S04444-4 and F07777-77. The diamond () indicates that subassembly A03333 is non-saleable and all the parts shown as included need to be purchased separately. REF
PART #
DESCRIPTION (Indicates Non-Saleable Items)
COMMENTS
QTY.
A01111
Sample Assembly
1
1
F02222-22
Sample Part
1
A03333
Sample Subassembly
1
2
S04444-4
Sample Part
1
3
F07777-77
Sample Part
1
To Order Parts:
1-2
From the continental U.S., call your local Lastec distributor to order parts. If there is no Lastec distributor in your area, call 1-800-515-6798. Have your customer number, unit serial number, and part numbers ready when you call.
From other international locations, contact the Lastec distributor in your area for parts.
Mower//042315
General Information
General Information Torque Values
1.2
1
Torque Values Below is a table of suggested torque values for this unit. Please use these torque values on this unit unless otherwise specified. Grade
Units
SAE 5 105000 PSI
Tensile Strength
SAE 8 150000 PSI
Grade Mark
Bolt Dia.
Threads. Per In.
6 8 10 10 12 1/4 1/4 5/16 5/16 3/8 3/8 7/16 7/16 1/2 1/2 9/16 9/16 5/8 5/8 3/4 3/4 7/8 7/8 1
32 32 24 32 24 20 28 18 24 16 24 14 20 13 20 12 18 11 18 10 16 9 14 8
General Information
Units in-lbs in-lbs in-lbs in-lbs in-lbs in-lbs in-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs
(Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm) (Nm)
Mower//042315
SAE 5
SAE 8
20 (2.3) 24 (2.7) 35 (4.0) 40 (4.5) 50 (5.7) 95 (10.7) 95 (10.7) 17 (22.6) 20 (27.1) 30 (40.7) 35 (47.5) 50 (67.8) 55 (74.6) 75 (101.7) 85 (115.3) 105 (142.4) 115 (155.9) 150 (203.4) 160 (217.0) 170 (230.5) 175 (237.3) 302 (409.5) 300 (406.8) 466 (631.8)
30 (3.4) 45 (5.1) 50 (5.7) 65 (7.3) 125 (14.1) 150 (17.0) 23 (31.2) 25 (33.8) 40 (54.2) 45 (61.0) 65 (88.1) 70 (94.9) 100 (135.6) 110 (149.2) 135 (183.1) 150 (203.4) 195 (264.4) 210 (284.8) 220 (298.3) 225 (305.1) 473 (640.9) 400 (542.4) 714 (967.4)
1-3
1 1.3
General Information Decals
Decals Decals (US Only)
REF
1
1-4
PART #
DESCRIPTION
COMMENTS
QTY.
049629
Decal Kit, 2261ADC
2261 Model Only
1
055449
Decal Kit, 2273ADC
2273 Model Only
1
049638
Decal, Articulator 2261ADC
2261 Model Only
2
049459
Decal, 2273ADC Articulator Large
2273 Model Only
2
2
014419
Decal, Hot Engine Warning
1
3
019554
Decal, Warning, Operational Safety 425D
1
4
019557
Decal, Lastec Logo Div WM
3
5
028601
Decal, Fwd/Rev Motion
2
6
028603
Decal, Brake Control
1
7
040910
Decal, Warning Operate From Seat
1
8
040911
Decal, Warning Operate With Guards
2
9
040912
Decal, Danger, Thrown Objects/Arrow
1
10
049304
Decal, 33Hp Fuel Valve
1
11
042003
Decal, Warning, Slope
1
12
043225
Decal, Articulator Logo Div WM
1
13
049466
Decal, Comm. Deck Height Adjustment
1
14
048504
Decal, Lastec, Roll Bar
1
15
049930
Decal, Belt Routing 2861
1
16
049931
Decal, 61 Inch Cut
2261 Model Only
2
049465
Decal, 73 In
2273 Model Only
2
17
P478
Decal, Danger - Rotating Blades
1
18
045519
Decal, Sound Power Level
1
19
049300
Decal, Diesel Exhaust Warning
1
20
048227
Decal, Hydro Fill Line
1
21
044731
Decal, Control Box Engine Throttle
1
22
062425
Decal, Relays for 055700-055846
1
23
062428
Decal, Relay 5 in Control Box
1
24
062404
Decal, AGC/ADC Hydro
1
25
062429
Decal, Lastec Made in USA
1
26
063235
Decal, Control Box Diesel
1
27
056591
Decal, 18 PSI
2
28
019552
Decal, Caution ‘Clean Radiatior’
1
29
018784
Decal, Diesel Refuel Caution
2
Lastec//042315
General Information
1
General Information Decals
This unit uses hydraulic fluid
Fill Line ITEM 062425
CR-1
Relay Part # 050436
Located Next to Relays
049930
048227
Under Seat Pan
062404
Belt Routing
CR-2
CR-3
PART #
Hydraulic Filter
P620
Hydraulic Fluid (1qt)
040642
2.5 gal Service Kit
049929
5.0 gal Service Kit
049928
(uses 2 filters/mower)
CR-4
(includes 2 filters)
(includes 4 filters)
On Hydraulic Tank
Burn Hazard Avoid contact with any part of hot engine. Failure to do so may result in serious injury. Wood-Mizer Products, Inc. 800-525-8100 Reorder #014419
Center of Rear Bumper
WARNING Fill Tire to:
AVOID SERIOUS INJURY OR DEATH
18 psi
Operate from operator seat only. Follow all safety rules in owner manual during operation or maintenance.
056591
WARNING
040910
LWA 045519
044731
042003
DANGER THROWN OBJECTS Before mowing clear area of people and objects which may be thrown by blades. ROTATING BLADES Do not put hands or feet under or into mower when engine is running. 040912
WARNING AVOID SERIOUS INJURY OR DEATH
WARNING AVOID SERIOUS INJURY OR DEATH
Without all safety shields and guards in place at all times. 062428
040911
CR-5 Relay Part # 050436
Located Inside Control Box
General Information
OR
73”
OR
73”
Lastec//042315
Without all safety shields and guards in place at all times. 040911
2261_002
1-5
1
General Information Decals Decals (CE Only)
REF
1
PART #
DESCRIPTION
064530
Decal Kit, 2261ADC-CE
2261 Model Only
1
055449
Decal Kit, 2273ADC
2273 Model Only
1
QTY.
049638
Decal, Articulator 2261ADC
2261 Model Only
2
049459
Decal, 2273ADC Articulator Large
2273 Model Only
2
2
014419
Decal, Hot Engine Warning
1
3
019554
Decal, Warning, Operational Safety 425D
1
4
019557
Decal, Lastec Logo Div WM
3
5
028601
Decal, Fwd/Rev Motion
2
6
028603
Decal, Brake Control
1
7
040910
Decal, Warning Operate From Seat
1
8
040911
Decal, Warning Operate With Guards
2
9
040912
Decal, Danger, Thrown Objects/Arrow
1
10
049304
Decal, 33Hp Fuel Valve
1
11
042003
Decal, Warning, Slope
1
12
043225
Decal, Articulator Logo Div WM
1
13
049466
Decal, Comm. Deck Height Adjustment
1
14
048504
Decal, Lastec, Roll Bar
1
15
049930
Decal, Belt Routing 2861
1
16
049931
Decal, 61 Inch Cut
2261 Model Only
2
049465
Decal, 73 In
2273 Model Only
2
17
P478
Decal, Danger - Rotating Blades
1
18
045519
Decal, Sound Power Level
1
19
049300
Decal, Diesel Exhaust Warning
1
20
048227
Decal, Hydro Fill Line
1
21
044731
Decal, Control Box Engine Throttle
1
22
062425
Decal, Relays for 055700-055846
1
23
062428
Decal, Relay 5 in Control Box
1
24
062404
Decal, AGC/ADC Hydro
1
25
062429
Decal, Lastec Made in USA
1
26
063235
Decal, Control Box Diesel
1
27
056591
Decal, 18 PSI
2
28
019552
Decal, Caution ‘Clean Radiatior’
1
29
018784
Decal, Diesel Refuel Caution
2
040267
Decal Kit, European Languages
2
040256
Decal, Warning, Outer Decks -- German
1
040257
Decal, Warning, Outer Decks -- French
1
040258
Decal, Warning, Outer Decks -- Italian
1
040259
Decal, Warning, Outer Decks -- Spanish
1
Decal, Warning, Outer Decks -- Danish
1
040260 P117
1-6
COMMENTS
Decal, Hands & Feet
7
Lastec//042315
General Information
1
General Information Decals 041205
Decal, Thrown Objects CE Std
1
041206
Decal, Caution Symbol CE Std
2
041209
Decal, Keep Away/Rotating Drive Line CE
2
040267
Decal Kit, European Languages
2
CE
This unit uses hydraulic fluid
Fill Line ITEM Hydraulic Filter
P620
Hydraulic Fluid (1qt)
040642
2.5 gal Service Kit
049929
5.0 gal Service Kit
049928
062425
(uses 2 filters/mower)
CR-2
CR-3
CR-1
Relay Part # 050436
Located Next to Relays
049930
048227
Under Seat Pan
062404
Belt Routing
CR-4
PART #
(includes 2 filters)
(includes 4 filters)
On Hydraulic Tank 04120
Burn Hazard Avoid contact with any part of hot engine. Failure to do so may result in serious injury. Wood-Mizer Products, Inc. 800-525-8100 Reorder #014419
04120
Center of Rear Bumper
04120
WARNING Fill Tire to:
AVOID SERIOUS INJURY OR DEATH
18 psi
Operate from operator seat only. Follow all safety rules in owner manual during operation or maintenance.
056591
WARNING
040910
LWA 045519
044731
042003
DANGER THROWN OBJECTS Before mowing clear area of people and objects which may be thrown by blades. ROTATING BLADES Do not put hands or feet under or into mower when engine is running. 040912
WARNING AVOID SERIOUS INJURY OR DEATH
WARNING AVOID SERIOUS INJURY OR DEATH
Without all safety shields and guards in place at all times. 062428
040911
CR-5 Relay Part # 050436
Located Inside Control Box
General Information
OR
73”
OR
73” Lastec//042315
Without all safety shields and guards in place at all times. 040911
2261_017
1-7
1 1.4 REF
1-8
Mower Decks Hardware Kit (CE Only)
Hardware Kit (CE Only) PART #
DESCRIPTION
064522
Kit, 2261/73 CE Hardware
COMMENTS
QTY. 1
1
057559
Hood Assembly, 22HP Yanmar CE
1
2
064500
Nut Assembly, 3/8-16 Cover Retaining
6
3
F04203-6
Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop
6
IS-0308
Instruction Sheet, 2261/73 CE Hardware Kit
1
Lastec//042315
Mower Decks
Mower Decks Hardware Kit (CE Only)
1
290009
Mower Decks
Lastec//042315
1-9
2
SECTION 2 DRIVE SYSTEM
Mower//042315
2-1
2 2.1 REF
Drive System Seat Assembly
Seat Assembly PART #
DESCRIPTION
049590
Seat Assembly, Complete Gas
QTY. 1
Seat, Air Ride (Color Gray)
1
P630
2
P826
Switch, Seat
3
F412
Screw, Seat Switch
P776
Seat Belt, 2” ALR/ERI Buckle
1 1 2 Sold as a pair
1
4
049589
Pan Weldment, Seat
1
5
F05007-244
Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS
2
6
F05010-234
Nut, 3/8-16 Hex Half Nylon Lock 316 SS
7
F05010-58
Nut, 5/16-18 Nylok Hex
3 Added after Serial # 1940306 1 Added after Serial # 2960906
7
8
024155
Clamp, 1/4" Wire 13/32” Mtg Hole
Added after Serial # 2960906
1
2
9
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
Added after Serial # 2960906
1
10
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
3 Added after Serial # 1940306
5
11
F05011-50
Washer, 5/16” x 1 1/4” Fender
3 Added after Serial # 1940306
4
12
045988
Cable, Seat Lanyard
Added after Serial # 1940306
2
13
014818 052025
2-2
COMMENTS
Spring, Extension 3/8” x 3” Seat Delay Assembly, LasTec Mowers
Lastec//042315
1 Not Shown
1
Drive System
Drive System Seat Assembly
2
LT0064
Drive System
Lastec//042315
2-3
2 2.2 REF
1
Drive System Roll-Over Protection System (ROPS)
Roll-Over Protection System (ROPS) PART #
DESCRIPTION
049796
ROPS Assembly, 2861 Folding
COMMENTS
QTY. 1
1
049831 1
Frame Weldment, ROPS
1
2
0497361
Frame Weldment, Comm. ROPS Lower
1
3
049736-11
Frame Weldment, Comm. ROPS Lower
1
4
049447
Knob w/Stud, 3/8-16 x 1.50”
2
5
F05010-10
Nut, 3/8-16 Hex Nyloc
10
6
049448
Pull Pin, 1/2”
2
7
F05008-23
Bolt, 1/2-13 x 3” Hex Head Grade 5
2
8
049446
Washer, 1.50” OD x .53” ID UHMW
4
9
F05010-8
Nut, 1/2-13 Nylon Hex Lock
2
10
F05007-126
Bolt, 3/8-16 x 4” Hex Head Grade 5
4
11
F05011-3
Washer, 3/8” Flat SAE
4
12
F05007-206
Bolt, 3/8-16 x 2 3/4” Hex Head Grade 5
4
ROPS framing members may not be sold separately. When ordering, you will receive all three frame weldments (049831, 049736 and 049736-1).
2-4
Lastec//042315
Drive System
Drive System Roll-Over Protection System (ROPS)
2
LT0065
Drive System
Lastec//042315
2-5
2
Drive System Rocker Assembly (Serial # 2130406 and prior)
2.3 REF 1
Rocker Assembly (Serial # 2130406 and prior) PART #
DESCRIPTION
COMMENTS
F05005-79
Bolt, 1/4-20 x 1/2” Hex Head Cap
QTY. 4
2
F05011-14
Washer, 1/4” Split Lock
4
3
F05011-11
Washer, 1/4” SAE Flat
4
4
049791
Cover, Left Rocker
1
049792
Cover, Right Rocker
1
5
F05009-10
Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5
1
6
F05008-106
Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5
1
7
F05010-185
Nut, 5/8-11 Flexloc
8
F05010-8
Nut, 1/2-13 Nyl Hex Lock
3 1 added after serial # 1660206
4
9
F05008-23
Bolt, 1/2-13 x 3” Hex Head Grade 5 Zinc
2
10
F05009-37
Bolt, 5/8-11 X 3” Hex Head Grade 5 Zinc
2
11
049710
Rocker Weldment, Left
049717
Rocker Weldment, Right
11
61” deck
1 1
055384
Rocker Weldment, 73” Right
055385
Rocker Weldment, 73” Left
73” Deck
1
12
P107
Fitting, 1/4-28 Straight Grease
1
13
049893
Washer, 3 1/2” OD Wave
1
14
048173
Washer, Wheel Damper
1
15
048174
Block, Wheel Yoke Friction
1
16
F05011-5
Washer, 5/8” SAE Flat
17
F05008-35
Bolt, 1/2-13 x 4-1/2” Hex Head Gr5
18
043285
Spring, .72” x 2.75” x .105” MW
Added after serial # 1660206
1
19
F05010-8
Nut, 1/2-13 Nyl Hex Lock
Added after serial # 1660206
1
1
Added after serial # 1660206
2 1
NOTE: Left and right Rockers are mirror images of each other. Be sure to order the correct weldment or cover for the side needed. (Left side shown in illustration.)
2-6
Lastec//042315
Drive System
Drive System Rocker Assembly (Serial # 2130406 and prior)
2
049715
Drive System
Lastec//042315
2-7
2 2.4 REF
Drive System Rocker Assembly, 61” Deck (Serial # 2140406 and later)
Rocker Assembly, 61” Deck (Serial # 2140406 and later) PART #
DESCRIPTION
COMMENTS
055086
Rocker Assembly, Right
Right Side Only
QTY. 1
055085
Rocker Assembly, Left
Left Side Only
1
1
F05009-10
Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5
2
F05008-106
Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5
1
3
F05010-185
Nut, 5/8-11 FlexLoc
3
4
F05010-8
Nut, 1/2-13 Nyl Hex Lock
3
5
F05008-23
Bolt, 1/2-13 x 3” Hex Head Grade 5
2
6
F05009-37
Bolt, 5/8-11 x 3 Hex Head Grade 5
7
055084
Rocker Weldment, Right
Right Side Only
1
055486
Rocker Weldment, Left
Left Side Only. Serial #24441106 and later
1
055083
Rocker Weldment, Left
Left Side Only. Serial #2130406 to 24431106
1
8
P195
Cap, Hub
1
9
P107
Fitting, 1/4-28 Straight Grease
1
10
P191
Seal, 1 1/4” ID Trb Bearing
1
11
049893
Washer, 3-1/2” OD Wave
1
12
048173
Washer, Wheel Damper
1
13
048174
Block, Wheel Yoke Friction
1
049668
Wheel Yoke Assembly, 13” Comm Right
Right Side Only. See Section 2.10
1
046477
Wheel Yoke Assembly, 13” Comm
Left Side Only. See Section 2.10
1
Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5
Serial #2850806 and later
1
F05008-35
Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5
Serial #2850806 and prior
1
17
043285
Spring, 0.72” x 2.75” x 0.105” MW
18
F05010-201
Nut, 1/2-13 Hi-Crown Acorn Cap Plated
Serial #2850806 and later
1
F05010-8
Nut, 1/2-13 Nylon Hex Lock
Serial #2850806 and prior
1
049745
Rocker Wheel Assembly, Right
Right Side Only. See Section 2.9
1
049740
Rocker Wheel Assembly, Left
Left Side Only. See Section 2.9
1
049790
Lift Assembly, Right Rocker Deck
Right Side Only. See Section 2.7
1
055831
Lift Assembly, Left Rocker Deck
Left Side Only. See Section 2.6
1
14 15 16
19 20 1 Bolt,
F05011-5 F05008-106
1
2
2
Washer, 5/8” SAE Flat 1
1
spring and nut reversed orientation after serial #2850806.
NOTE: The left and right rocker assemblies are mirror images of each other. Be sure to order the correct rocker weldment, wheel yoke, rocker wheel and deck lift assemblies for the side needed. (Left side shown below.)
2-8
Lastec//042315
Drive System
Drive System Rocker Assembly, 61” Deck (Serial # 2140406 and later)
2
LT0066
Drive System
Lastec//042315
2-9
2 2.5 REF
Drive System Rocker Assembly, 73” Deck
Rocker Assembly, 73” Deck PART #
DESCRIPTION
COMMENTS
055386
Rocker Assembly, 73” Right
Right Side Only
055387
Rocker Assembly, 73” Left
Left Side Only
QTY. 1 1
1
F05009-10
Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5
2
F05008-106
Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5
1
3
F05010-185
Nut, 5/8-11 FlexLoc
3
4
F05010-8
Nut, 1/2-13 Nyl Hex Lock
3
5
F05008-23
Bolt, 1/2-13 x 3” Hex Head Grade 5
2
6
F05009-37
Bolt, 5/8-11 x 3 Hex Head Grade 5
7
055384
Rocker Weldment, Right
Right Side Only Left Side Only
055385
Rocker Weldment, Left
8
P195
Cap, Hub
1
2 1 1 1
9
P107
Fitting, 1/4-28 Straight Grease
1
10
P191
Seal, 1 1/4” ID Trb Bearing
1
11
049893
Washer, 3-1/2” OD Wave
1
12
048173
Washer, Wheel Damper
1
13
048174
Block, Wheel Yoke Friction
14
049668
Wheel Yoke Assembly, 13” Comm Right
Right Side Only. See Section 2.10
1
Left Side Only. See Section 2.10
1
1
046477
Wheel Yoke Assembly, 13” Comm
15
F05011-5
Washer, 5/8” SAE Flat
2
16
F05008-35
Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5
1
17
043285
Spring, 0.72” x 2.75” x 0.105” MW
1
18
F05010-201
Nut, 1/2-13 Hi-Crown Acorn Cap Plated
19
049745
Rocker Wheel Assembly, Right
Right Side Only. See Section 2.9
1
049740
Rocker Wheel Assembly, Left
Left Side Only. See Section 2.9
1
049790
Lift Assembly, Right Rocker Deck
Right Side Only. See Section 2.7
1
049726
Lift Assembly, Left Rocker Deck
Left Side Only. See Section 2.8
1
20
1
NOTE: The left and right rocker assemblies are mirror images of each other. Be sure to order the correct rocker weldment, wheel yoke, rocker wheel and deck lift assemblies for the side needed. (Left side shown below.)
2-10
Lastec//042315
Drive System
Drive System Rocker Assembly, 73” Deck
2
LT0059
Drive System
Lastec//042315
2-11
2 2.6 REF
Drive System Left Rocker Deck Lift Assembly, 61” Deck
Left Rocker Deck Lift Assembly, 61” Deck PART #
DESCRIPTION
055831
Lift Assembly, Left Rocker Deck
COMMENTS
QTY. 1
1
F05007-125
Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5
2
2
048712
Bushing, 1 1/16" Urethane Pivot
2
3
048692
Strap, 1U
2
4
F05011-3
Washer, 3/8” Flat SAE
4
5
F05010-10
Nut, 3/8-16 Hex Nyloc
4
6
055483
Lift Weldment, Left Deck
1
7
F05008-37
Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5
2
8
F05011-2
Washer, 1/2” SAE Flat
2
9
P829
Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz
2
10
F05007-126
Bolt, 3/8-16 x 4” Hex Head Grade 5
2
11
049725
Lift Weldment, Deck Tab
1
12
F05005-105
Screw, 1/4-28 x 1/4” BO Socket Head Pt Set
2
049843
Link Assembly, 3/8” Suspension
1
13
N/A
Bolt, 3/8-16 x 7” Hex Head Grade 5
Not sold separately
1
14
N/A
Washer, 3/8” Suspension
Not sold separately
4
15
N/A
Bushing, 3/8” Polyurethane Suspension
Not sold separately
4
16
N/A
Spacer, 3/8” Suspension
Not sold separately
1
17
F05010-10
Nut, 3/8-16 Hex Nyl Lock
2-12
Lastec//042315
1
Drive System
Drive System Left Rocker Deck Lift Assembly, 61” Deck
2
LT0060
Drive System
Lastec//042315
2-13
2 2.7 REF
Drive System Right Rocker Deck Lift Assembly, 61” and 73” Decks
Right Rocker Deck Lift Assembly, 61” and 73” Decks PART #
DESCRIPTION
049790
Lift Assembly, Right Rocker Deck
COMMENTS
QTY. 1
1
F05007-125
Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5
2
2
048712
Bushing, 1 1/16" Urethane Pivot
2
3
048692
Strap, 1U
2
4
F05011-3
Washer, 3/8” Flat SAE
4
5
F05010-10
Nut, 3/8-16 Hex Nyloc
4
6
049789
Lift Weldment, Right Deck
1
7
F05008-37
Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5
2
8
F05011-2
Washer, 1/2” SAE Flat
2
9
P829
Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz
2
10
F05007-126
Bolt, 3/8-16 x 4” Hex Head Grade 5
2
11
049725
Lift Weldment, Deck Tab
1
12
F05005-105
Screw, 1/4-28 x 1/4” BO Socket Head Pt Set
2
049843
Link Assembly, 3/8” Suspension
1
13
N/A
Bolt, 3/8-16 x 7” Hex Head Grade 5
Not sold separately
1
14
N/A
Washer, 3/8” Suspension
Not sold separately
4
15
N/A
Bushing, 3/8” Polyurethane Suspension
Not sold separately
4
16
N/A
Spacer, 3/8” Suspension
Not sold separately
1
17
F05010-10
Nut, 3/8-16 Hex Nyl Lock
2-14
Lastec//042315
1
Drive System
Drive System Right Rocker Deck Lift Assembly, 61” and 73” Decks
2
LT0063
Drive System
Lastec//042315
2-15
2 2.8 REF
Drive System Left Rocker Deck Lift Assembly, 73” Deck
Left Rocker Deck Lift Assembly, 73” Deck PART #
DESCRIPTION
049726
Lift Assembly, Left Rocker Deck
COMMENTS
QTY. 1
1
F05007-125
Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5
2
2
048712
Bushing, 1 1/16" Urethane Pivot
2
3
048692
Strap, 1U
2
4
F05011-3
Washer, 3/8” Flat SAE
4
5
F05010-10
Nut, 3/8-16 Hex Nyloc
4
6
049720
Lift Weldment, Left Deck
1
7
F05008-37
Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5
2
8
F05011-2
Washer, 1/2” SAE Flat
2
9
P829
Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz
2
10
F05007-126
Bolt, 3/8-16 x 4” Hex Head Grade 5
2
11
049725
Lift Weldment, Deck Tab
1
12
F05005-105
Screw, 1/4-28 x 1/4” BO Socket Head Pt Set
2
049843
Link Assembly, 3/8” Suspension
1
13
N/A
Bolt, 3/8-16 x 7” Hex Head Grade 5
Not sold separately
1
14
N/A
Washer, 3/8” Suspension
Not sold separately
4
15
N/A
Bushing, 3/8” Polyurethane Suspension
Not sold separately
4
16
N/A
Spacer, 3/8” Suspension
Not sold separately
1
17
F05010-10
Nut, 3/8-16 Hex Nyl Lock
2-16
Lastec//042315
1
Drive System
Drive System Left Rocker Deck Lift Assembly, 73” Deck
2
LT0060
Drive System
Lastec//042315
2-17
2 2.9 REF
1
2
Drive System Rocker Wheel Assembly
Rocker Wheel Assembly PART #
DESCRIPTION
COMMENTS
049745
Rocker Wheel Assembly, Right
Right Side Only
QTY.
049740
Rocker Wheel Assembly, Left
Left Side Only
1
049870
Bushing, Urethane Pivot
Apply water-proof axle grease to mating surfaces prior to assembly. Serial #1660206 and later
2
049510
Bushing, Rubber Pivot
Serial #2780806 and prior. No longer available; order 049870
2
049744
Weldment, Right Rocker Wheel Pivot
Right Side Only
1
049741
Weldment, Left Rocker Wheel Pivot
Left Side Only
1
1
3
F05010-34
Nut, 5/8-11 Nyl Lock
1
4
F05011-5
Washer, 5/8” SAE Flat
1
5
027013
Wheel, Anti-Scalp 5-5/8" hole
1
NOTE: The left and right assemblies are mirror images of each other. Be sure to order the correct weldment for the side needed. (Left side shown below.) CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
2-18
Lastec//042315
Drive System
Drive System Rocker Wheel Assembly
2
LT0061
Drive System
Lastec//042315
2-19
2
Drive System Wheel Yoke Assembly
2.10 Wheel Yoke Assembly REF
PART #
DESCRIPTION
COMMENTS
046477
Wheel Yoke Assembly, 13” Comm
Left Side & Front Only
1
049668
Wheel Yoke Assembly, 13” Comm Right
Right Side Only
1
Nut, 3/4-16 Castle
QTY.
1
P434
1
2
F05011-62
Washer, 3/4” SAE Flat
1
3
P190
Bearing, 1” ID Tapered Roller
1
4
043968
Spacer, Wheel Yoke Bearing
5
F05012-79
Pin, 5/32” x 1 1/2” Cotter
Serial # 2161105 and later Serial # 2151105 and prior
2 1
F05012-49
Pin, 1/8” x 1 1/2” Cotter
6
046478
Yoke Weldment, 2561 Front Wheel
7
F05009-108
Bolt, 3/4-10 x 9” Hex Head Grade 5
1
8
F05010-177
Nut, 3/4-10 Stover Swaged
1
9
045986
Wheel Assembly, 13” x 6.5” x 6”
10
P296
Spacer, 1.13” OD x .75” ID x .5”
2-20
Lastec//042315
1 1
See Section 2.11
1 2
Drive System
Drive System Wheel Yoke Assembly
2
Valve Stem This Side (Left Side Assembly Only)
Valve Stem This Side (Right Side Assembly Only)
Drive System
LT0054
Lastec//042315
2-21
2
Drive System Wheel Assembly, 13 x 6.50 x 6
2.11 Wheel Assembly, 13 x 6.50 x 6 REF
PART #
DESCRIPTION
045986
Wheel Assembly, 13” x 6.5” x 6”
COMMENTS
QTY. 1
1
P293
Seal, TRB, 3/4” ID
2
2
P292
Bearing, Tapered Roller, 3/4” ID
2
3
P402
Bearing Race Insert, 3/4" TRB
2
NOTE: The tire and hub are not sold separately and they are included in Wheel Assembly (045986).
2-22
Lastec//042315
Drive System
Drive System Wheel Assembly, 13 x 6.50 x 6
2
LT0053
Drive System
Lastec//042315
2-23
2
Drive System Control Box Assembly (Serial # 24331106 and prior)
2.12 Control Box Assembly (Serial # 24331106 and prior) REF
PART #
DESCRIPTION
COMMENTS
QTY.
1
F05004-93
Screw, 6-32 x 3/4 SBHC SS
6
2
043956
Clamp, Blade Switch Mount
2
3
044588
Switch, Blade Start/Stop
1
4
046129
Hour Meter, Digital LCD
1
5
024378
Switch, Key Diesel (Kubota)
1
6
048965
Decal, Control Box
1
7
046751
Control Box Weldment
1
8
F05011-17
Washer, 5/16” SAE Flat
3
9
F05011-13
Washer, 5/16” Split Lock
3
10
F05006-102
Bolt, 5/16-18x3/4 HH Gr5 Zinc
3
11
019613
Plug, 1/2” Hole
1
12
050477-1
Light Assembly, LED Red 3/16 FI Male Quicks
2
13
F05004-3
Screw, #10-24 x 3/8 Phillips PH Machine->
3
14
F05011-20
Washer, #10 Split Lock
2
15
048953
Plate, Control Box Access
1
16
F05010-59
Nut, #6-32 Keps
17
F05010-44
Nut, #6-32 Hex
18
041669
Socket, 12V Accessory Panel Mount
1
19
049306
Alarm, 3372 / 3386
1
20
F05010-14
Nut, #10-24 Keps->
028507
Keys
2-24
2 Deleted after 2281205
2
1 Set of 2 Replacement Keys Not Shown
Lastec//042315
1
Drive System
Drive System Control Box Assembly (Serial # 24331106 and prior)
2
046750A
Drive System
Lastec//042315
2-25
2
Drive System Control Box Assembly (Serial # 24331106 and 35471009)
2.13 Control Box Assembly (Serial # 24331106 and 35471009) REF
PART # 046750
1
DESCRIPTION
COMMENTS
QTY.
Control Box Assembly
1
1
F05004-93
Screw, 6-32 x 3/4” SBHC SS
6
2
043956
Clamp, Blade Switch Mount
2
3
044588
Switch, Blade Start/Stop
1
4
046129
Hour Meter, Digital LCD
1
5
063212
Cap, Diesel Starter Switch
6
024378
Switch, Key Diesel (Kubota)
1
7
048965
Decal, Control Box
1
8
044712
Control Box Weldment, AC Diesel w/ Throttle
1
Added with Serial # 34860709
1
9
F05011-17
Washer, 5/16” SAE Flat
3
10
F05011-13
Washer, 5/16” Split Lock
3
11
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
3
12
019613
Plug, 1/2” Hole
1
13
050477-1
Light Assembly, LED Red 3/16” FI Male Quicks
2
14
F05015-17
Bolt, #10-24 x 1/2” Ph Pan Head, Type 23
3
15
F05011-20
Washer, #10 Split Lock
2
16
048953
Plate, Control Box Access
1
17
F05010-59
Nut, #6-32 Keps
6
18
F05010-160
Nut, 10-24 Hex Nylock->
1
19
041669
Socket, 12V Accessory Panel Mount
1
20
049306
Alarm, 3372 / 3386
1
21
F05010-10
Nut, 3/8-16 Hex Nyloc
1
22
F05011-61
Washer, 3/8” SAE Flat
1
23
046239
Washer, Throttle Friction
1
24
044715
Handle Weldment, Throttle
1
25
019086
Knob, 1 3/8” x 3/8-24
1
26
046251
Washer Plate, Throttle Friction
1
27
046293
Washer, Throttle Friction
1
28
F05007-127
Bolt, 3/8-16 x 1 1/4” Carriage Grade 5
1
29
F05005-137
Bolt, 1/4-20 x 5/8” Hex Head Grade 5
2
30
F05011-14
Washer, 1/4” Split Lock
2
31
061974 1
Clamp, Cable
1
32
F05010-17
Nut, 5/16-18 Hex
1
33
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
1
044731
Decal, Control Box Engine Throttle
Not Shown
1
050436
Relay, 40A 12VDC Automotive
Not Shown. See Engine Section
1
061974 replaced 046240 Throttle Conduit Clamp (serial # 33600109 and later).
2-26
Lastec//042315
Drive System
Drive System Control Box Assembly (Serial # 24331106 and 35471009)
2
CM0001-1
Drive System
Lastec//042315
2-27
2
Drive System Control Box Assembly
2.14 Control Box Assembly REF
PART # 063229
DESCRIPTION
COMMENTS
QTY.
Control Box Assembly
1
1
F05004-93
Screw, 6-32 x 3/4” SBHC SS
6
2
043956
Clamp, Blade Switch Mount
2
3
044588
Switch, Blade Start/Stop
1
4
046129
Hour Meter, Digital LCD
1
5
063212
Cap, Diesel Starter Switch
1
6
024378
Switch, Key Diesel (Kubota)
1
7
063230
Control Box Weldment, Diesel w/ Throttle
1
8
F05011-17
Washer, 5/16” SAE Flat
3
9
F05011-13
Washer, 5/16” Split Lock
3
10
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
3
11
019613
Plug, 1/2” Hole
4
12
050477-1
Light Assembly, LED Red 3/16” FI Male Quicks
2
13
F05015-17
Bolt, #10-24 x 1/2” Ph Pan Head, Type 23
4
14
F05011-20
Washer, #10 Split Lock
2
15
048953
Plate, Control Box Access
1
16
F05010-59
Nut, #6-32 Keps
6
17
F05010-160
Nut, 10-24 Hex Nylock->
2
18
041669
Socket, 12V Accessory Panel Mount
1
19
049306
Alarm, 3372 / 3386
1
20
F05010-10
Nut, 3/8-16 Hex Nyloc
1
21
F05011-61
Washer, 3/8” SAE Flat
1
22
046239
Washer, Throttle Friction
1
23
044715
Handle Weldment, Throttle
1
24
019086
Knob, 1 3/8” x 3/8-24
1
25
046251
Washer Plate, Throttle Friction
1
26
046293
Washer, Throttle Friction
1
27
F05007-127
Bolt, 3/8-16 x 1 1/4” Carriage Grade 5
1
28
F05005-137
Bolt, 1/4-20 x 5/8” Hex Head Grade 5
2
29
F05011-14
Washer, 1/4” Split Lock
2
30
061974
Clamp, Cable
1
31
F05010-17
Nut, 5/16-18 Hex
1
32
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
1
33
063218 1
Gauge, Temperature 0-250 Deg Electric
1
34
063220
Gauge, Tachometer 0-4000 RPM 16-Pole
Added S/N 39270211 and later
1
35
063219
Sender, Water Temperature 0-250 Deg
Added S/N 39270211 and later
1
064485
Wire Harness, 3300 Gauge Kit
Added S/N 39270211 and later
1
067775
Jumper, Kubota Key Switch
36
2-28
1
063235
Decal, Control Box Diesel
1
050436
Relay, 40A 12VDC Automotive
1
Lastec//042315
Drive System
Drive System Control Box Assembly 1
2
Replaced Temperature Gauge (063238), Fitting (063239) and 2” Hole Plug (063237) with serial #39270211 and later.
LT0052D
Drive System
Lastec//042315
2-29
2
Drive System Diesel Throttle Cable Assembly
2.15 Diesel Throttle Cable Assembly REF
PART # 061952
1
1
DESCRIPTION
COMMENTS
Cable Assembly, Diesel Throttle
QTY. 1
1
055443
Cable Assembly, 2261 Throttle
2
061954
Grommet, Cable Wiper
1
3
F05010-119
Nut, 5/16-24 Jam LH
2
4
F05011-17
Washer, 5/16” SAE Flat
2
5
061953
Boot, Vinyl Cable
1
6
048904
Throttle Fitting, Swivel
1
1
061952 now includes cable grommet and boot (serial # 33600109 and later). Service Kit (063210) was created for models with serial # prior to 33600109. See bulletins PB-0256 and IS-0257 for more information.
2-30
Lastec//042315
Drive System
Drive System Diesel Throttle Cable Assembly
2
CM0001-2
Drive System
Lastec//042315
2-31
2
Drive System Hand Contol Assembly
2.16 Hand Contol Assembly REF
PART #
DESCRIPTION
COMMENTS
049706
Arm Assembly, Right Control Handle
Right Side Only
QTY. 1
049707
Arm Assembly, Left Control Handle
Left Side Only
1
1
028390
Grip, Handle
1
2
027015
Arm Weldment, 2561 Right Control
Right Side Only
1
027016
Arm Weldment, 2561 Left Control
Left Side Only
1
3
F05007-87
Bolt, 3/8-16 x 1” Hex Head Grade 5
3
4
F05011-4
Washer, 3/8” Split Lock
2
5
F05011-3
Washer, 3/8” Flat SAE
6
048393
Mount, Extended Drive Handle
Serial #1940106 and later
1
043950
Block, Drive Handle Mount
Serial #1520306 and prior
1
7
P05035
Collar, 5/8” ID Lock
8
F05005-105
9
014834
2
2
Screw, 1/4-28 x 1/4” BO SH Cup Pt Set
2
Bearing, w/Snap Ring 5/8” ID
2
10
F05010-124
Nut, 3/8-16 Half Nyloc
1
11
F05008-96
Bolt, 5/16-18 x 1 1/2” Hex Head Grade 5
1
12
F05010-58
Nut, 5/16-18 Nylok Hex
1
13
043952
Arm Pivot Weldment, Right Control
1
14
F05010-1
Nut, 3/8-16 Hex
1
15
F05007-123
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
1
056450
Turnbuckle Assembly, Hydro Diesel Rod End, 3/8-24 Right Hand
1
16
018739
1
17
F05010-123
Nut, 3/8-24 Free
1
18
056449
Rod, Hydro Control Link
1
19
F05010-119
Nut, 5/16-24 Jam LH
1
20
014815
Rod End, 5/16-24 Male LH
1
NOTE: Right and Left Control Handle Arm Assemblies are mirror images of each other with the exception of the Control Arm Weldment (item 2).
2-32
Lastec//042315
Drive System
Drive System Hand Contol Assembly
2
LT0056
Drive System
Lastec//042315
2-33
2
Drive System Pedal Assembly (Optional as of serial #26270307)
2.17 Pedal Assembly (Optional as of serial #26270307) REF
PART #
DESCRIPTION
COMMENTS
056241
Pedal Kit, AGC Foot
Optional
049739
Rod Assembly, Foot Control
QTY. 1 2
1
049738
Rod Weldment, Foot Control
2
F05011-3
Washer, 3/8” Flat SAE
1
3
F05011-110
Washer, 3/8” Push Nut
1
4
F05010-123
Nut, 3/8-24 Free
1
5
P110
Pin, 3/8” x 1 5/16” Clevis
1
6
F05012-3
Pin, 1/8” x 3/4” Cotter
1
7
P686
Yoke, 3/8In-24
1
Pedal Assembly, Control
2
049728
1
8
P629
Grip, Foot Control Black
1
9
049730
Pedal Weldment, Foot Control
1
10
029842
Bushing, 3/4” ID x 1” OD x 1” Oil
2
11
F05011-111
Washer, 20mm Bellville
1
12
F05011-77
Washer, 3/4” AN Yel/Cad
1
13
F04254-46
Ring, 3/4” External - External
1
14
P107
Fitting, 1/4-28 Straight Grease
1
IS-0218
Instruction Sheet, 056241 Kit
1
NOTE: To add this Foot Pedal option to your unit after serial #26270307, order Foot Pedal Kit (056241).
2-34
Lastec//042315
Drive System
Drive System Pedal Assembly (Optional as of serial #26270307)
2
LT0067
Drive System
Lastec//042315
2-35
2
Drive System Throttle Assembly (Deleted after Serial # 24321106)
2.18 Throttle Assembly (Deleted after Serial # 24321106) REF 1
PART # 049856
DESCRIPTION
COMMENTS
Cable Assembly, 2861 Throttle
QTY. 1
2
046240
Clamp, Throttle Conduit
1
3
019086
Knob, 1 3/8” x 3/8-24
1
4
F05015-17
Bolt, #10-24 x 1/2” PH
1
5
F05007-127
Bolt, 3/8-16 x 1 1/4” Carriage Grade 5
1
6
046251
Washer Plate, Throttle Friction
1
7
046293
Washer, Throttle Friction
1
8
046236
Handle Weldment, Throttle
1
9
046239
Washer, Throttle Friction
1
10
F05011-3
Washer, 3/8” SAE Flat
1
11
F05010-10
Nut, 3/8-16 Hex Nyl Lock
1
NOTE: Throttle moved to control box location after Serial #24321106.
2-36
Lastec//042315
Drive System
Drive System Throttle Assembly (Deleted after Serial # 24321106)
2
049544T
Drive System
Lastec//042315
2-37
2
Drive System Front Deck Lift Rod Assembly (Serial #24311106 and prior)
2.19 Front Deck Lift Rod Assembly (Serial #24311106 and prior) REF
PART #
1
F05007-136
DESCRIPTION
COMMENTS
QTY.
2
F05007-126
Bolt, 3/8-16 x 4” Hex Head Grade 5
1
3
034930
Plate Weldment, Deck Height Adjustment
1
4
F05010-10
Nut, 3/8-16 Hex Nyloc
10
5
048468
Rod End, 7/16-20 x 3/8 High Misalign
2
6
F05007-119
Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5
4
7
F05011-3
Washer, 3/8” Flat SAE
5
8
047234
Spring, .72 x 2.75 x .095 Dia SS Comp
1
9
047187
Spacer, 5/8” x 1” x 5/8”
1
10
F05010-38
Nut, 7/16-20 Jam
2
11
049787
Turnbuckle, Deck Lift Link
2
12
F05010-166
Nut, 3/8-24 LH Jam
2
13
018740
Rod End 3/8-24 Left Hand
2
14
S12284
Tube, 7/8” Dia Elec Motor Spacer
2
15
F05010-124
Nut, 3/8-16 Half Nyloc
1
16
F05004-123
Bolt, 3/8-16 x 3 1/2” Hex Head Gr5
1
17
P111
Ring, Kick-out, 1”
1
18
P212
Pin, 3/8” x 2 1/8” Clevis, Yzn
19
048712
Bushing, 1-1/16" Urethane Pivot
20
048692
Strap, 1U
21
F05006-81
22 23 24
F05007-73
Bolt, 3/8-16 x 3” Hex Head Gr5
1
25
049545
Rod Weldment, Front Deck Lift
1
Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5
4
1 Apply water-proof axle grease to mating surfaces prior to assembly
2
Bolt, 5/16-18 x 1 3/4” FT Hex Head Gr5
Added after serial # 1940306
1
F05010-17
Nut, 5/16-18 Hex
Added after serial # 1940306
1
P04211
Knob, 5/8-18 Ball
2
1
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
2-38
Lastec//042315
Drive System
Drive System Front Deck Lift Rod Assembly (Serial #24311106 and prior)
2
049544
Drive System
Lastec//042315
2-39
2
Drive System Front Deck Lift Rod Assembly (Serial #24331106 and later)
2.20 Front Deck Lift Rod Assembly (Serial #24331106 and later) REF
PART #
DESCRIPTION
049544
Rod Assembly, Front Deck Lift
COMMENTS
QTY. 1
1
F05007-136
Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5
4
2
F05007-126
Bolt, 3/8-16 x 4” Hex Head Grade 5
1
3
055464
Plate Weldment, Deck Height Adjust
1
4
F05010-10
Nut, 3/8-16 Hex Nyloc
6
5
P04211
Knob, 5/8-18 Ball
1
6
048187
Handle Weldment, Deck Raise
1
7
F05007-73
Bolt, 3/8-16 x 3” Hex Head Grade 5
1
8
047234
Spring, .72” x 2.75” x .095” Dia. SS Comp
1
9
F05011-3
Washer, 3/8” Flat SAE
5
10
049545
Rod Weldment, Front Deck Lift
1
11
F05004-123
Bolt, 3/8-16 x 3 1/2” Hex Head Grade 5
1
12
F05010-124
Nut, 3/8-16 Half Nyloc
1
13
048712
Bushing, 1 1/16" Urethane Pivot
14
048692
Strap, 1U
2
15
P212
Pin, 3/8” x 2 1/8” Clevis
1
16
Apply water-proof axle grease to mating surfaces prior to assembly
2
P111
Ring, 1” Kick-Out
1
049788
Rod Assembly, Deck Lift Link
2
17
F05010-10
Nut, 3/8-16 Hex Nyloc
2
18
S12284
Tube, 7/8” Dia. Elec Motor Spacer
1
19
018740
Rod End 3/8-24 Left Hand
1
20
F05007-119
Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5
2
21
F05010-166
Nut, 3/8-24 LH Jam
1
22
049787
Turnbuckle, Deck Lift Link
1
23
F05010-38
Nut, 7/16-20 Jam
1
24
048468
Rod End, 7/16-20 x 3/8” High Misalign
1
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
2-40
Lastec//042315
Drive System
Drive System Front Deck Lift Rod Assembly (Serial #24331106 and later)
2
LT0057
Drive System
Lastec//042315
2-41
2
Drive System Emergency Brake Assembly
2.21 Emergency Brake Assembly REF
PART #
DESCRIPTION
049550
Handle Assembly, E-Brake
COMMENTS
QTY. 1
1
P04211
Knob, 5/8-18 Ball
1
2
029360
Handle Weldment, E-Brake
1
3
F05010-10
Nut, 3/8-16 Hex Nyloc
2
4
P786
Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged
1
5
F05012-115
Pin, 3/4” Clevis Retaining
1
6
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
2
7
049537
Arm, E-Brake Link
1
8
029214
Spacer, 1.00” OD x .41” ID x 1/4” Thk Nylon-Blk
2
9
F05010-8
Nut, 1/2-13 Nyl Hex Lock
1
10
F05011-2
Washer, 1/2” SAE Flat
1
11
F05011-97
Washer, 1/2” Plain Belleville
6
12
029354
Block, E-Brake Pivot
1
13
029397
Rod Weldment, Brake Actuator
1
14
026407
Plate Weldment, E-Brake Lock
1
15
F05012-11
Pin, 3/16” x 1” Roll
1
16
026412
Rod Weldment, E-Brake Tensioner
1
17
F05012-1
Pin, 1/8” x 1” Cotter
1
18
P110
Pin, 3/8” x 1 5/16” Clevis
1
19
026409
Pulley, E-Brake
1
20
026416
Cable E-Brake
1
2-42
Lastec//042315
Drive System
Drive System Emergency Brake Assembly
2
LT0055
Drive System
Lastec//042315
2-43
2
Drive System Rear Deck Lift Rod Assembly
2.22 Rear Deck Lift Rod Assembly REF
PART #
DESCRIPTION
049541
Rod Assembly, Rear Deck Lift
COMMENTS
1
F05007-136
Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5
2
048712
Bushing, 1 1/16" Urethane Pivot
3
048692
Strap, 1U
QTY. 1 4
Apply water-proof axle grease to mating surfaces prior to assembly.
2 2
4
F05011-3
Washer, 3/8” Flat SAE
4
5
F05010-10
Nut, 3/8-16 Hex Nyloc
7
6
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
2
026448
Turnbuckle Assembly, Deck Lift
1
7
018740
Rod End 3/8-24 Left Hand
1
8
F05010-166
Nut, 3/8-24 LH Jam
1
9
026447
Turnbuckle, Deck Lift
1
10
F05010-22
Nut, 3/8-24 UNF Hex Jam
1
11
018739
12
026446
Rod End, 3/8-24 Right Hand
1
Rod Wldmnt, Spring Tensioner
1
13
F05011-101
Washer, 1/2” SAE Flat Gr5-8 (Thru Hard)
1
14
055442
Washer, 1/2” Delrin
1
15
026443
Block, Spring Tensioner
1
16
026371
Spring, 1 3/8" x 15.8” x .187” Extension
2
17
046534
Mount, Spring
1
18
F05007-109
Bolt, 3/8-16 x 4 3/4” Hex H ead Grade 5
1
19
049542
Rod Wldmnt, Rear Deck Lift
20
P110
Pin, 3/8” x 1 5/16” Clevis
Serial # 1940306 and later
F05012-8
Pin, 3/8” x 1 3/32” Clevis
Serial # 1520306 and prior
P111
Ring, 1” Kick-Out
21
1 2 2 2
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
2-44
Lastec//042315
Drive System
Drive System Rear Deck Lift Rod Assembly
2
LT0058
Drive System
Lastec//042315
2-45
2
Drive System Framework
2.23 Framework REF 1
PART #
DESCRIPTION
F05010-58
Nut, 5/16-18 Nylon Lock Hex
COMMENTS
QTY. 1
2
F05011-17
Washer, 5/16” SAE Flat
1
3
024155
Clamp, 1/4” Wire 13/32 Mtg Hole
1
4
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
1
5
F05007-125
Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5
2
6
047234
Spring, .72” x 2.75” x .095” Dia SS Comp
2
7
F05010-10
Nut, 3/8-16 Hex Nyloc
2
8
F05010-14
Nut, #10-24 Keps
4
9
043459
Switch, DPST NO 5A Plunger
3
10
F05004-126
Screw, 10-24 x 3/4” Phillips PH Machine
4
11
046559
Switch, DPST N/O N/C
1
12
F05004-1
Screw, 10-24 x 1/2” Sl Hex Machine
4
13
F05011-20
Washer, #10 Split Lock
4
14
044021
Cover, Handle Lockout Switch Left
1
15
044020
Cover, Handle Lockout Switch Right
16
049870
Bushing, Urethane Pivot
Apply water-proof axle grease to mating surfaces prior to assembly
6
17
P195
Cap, Hub
1
18
049984
Sure Grip, Foot Pan
1
19
055841
Sure Grip, 1 1/2” Bar
1
20
P107
Fitting, 1/4-28 Straight Grease
1
21
P611
Holder, Jumbo Cup Black
22
046477
Wheel Yoke Assembly, 13” Comm
2 See Section 2.10
1
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
2-46
Lastec//042315
Drive System
Drive System Framework
2
LT0068
Drive System
Lastec//042315
2-47
2
Drive System Pull Bar Assembly
2.24 Pull Bar Assembly REF
PART #
DESCRIPTION
049488
Bar Assembly, Pull
COMMENTS
QTY. 1
1
049484
Bar Weldment, Pull
1
2
F05009-35
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
4
3
F0510-185
Nut, 5/8-11 FlexLoc
4
4
F05011-40
Washer, 5/8” Standard Flat
2
2-48
Lastec//042315
Drive System
Drive System Pull Bar Assembly
2
3373_018
Drive System
Lastec//042315
2-49
2
Drive System Striping Kit (Optional)
2.25 Striping Kit (Optional) REF
PART #
DESCRIPTION
042947
Striping Kit, Commercial Mower
COMMENTS
QTY. 1
1
042951
Bracket Weldment, Left Striping Kit
1
2
042950
Bracket Weldment, Right Striping Kit
1
3
042949
Plate Weldment, Hanger Strap
1
4
042943
Plate, Mount Washer
2
5
F05011-9
Washer, 1/2” Split Lock
4
6
F05008-37
Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5
4
7
042945
Pad, Rubber Striping
1
8
042942
Strap, Rubber Pad Mounting
1
9
F05011-4
Washer, 3/8” Split Lock
6
10
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
6
IS-0192
Instruction Sheet, 61” Deck Striping Kit
1
NOTE: This 042947 Striping Kit may be purchased through your Lastec Dealer.
2-50
Lastec//042315
Drive System
Drive System Striping Kit (Optional)
2
LT0045
Drive System
Lastec//042315
2-51
3
SECTION 3 HYDRAULIC SYSTEM
Lastec//042315
3-1
3
Hydraulic System Hydraulic Layout Diagram
3.1
Hydraulic Layout Diagram
REF
PART #
DESCRIPTION
COMMENTS
QTY.
1
048776
Hose, 3/8” Hyd x 14” Low Pressure
2
2
040386
Hose, 3/8” Hyd x 25” Low Pressure
2
3
042941
Hose, 3/8” Hyd x 22” Low Pressure
1
4
042941
Hose, 3/8” Hyd x 22” Low Pressure
1
5
041180
Hose Assembly, 26” OAL x 1/2” Hyd
4
6
049273
Hose, 3/8” Hyd x 11” Low Pressure
2
015485
Fitting, 3/8” Barb Tee
061807
Hose Clamp, Dixon Worm Gear HSS6
7
1 Not Shown
14
Hydraulic Mainentance Kits PART # 049928 028535 P620 049929
COMMENTS
Kit, Hydro Oil Repl 5 Gal 3372
QTY. 1
Oil, Shell TTF-SB
5 gal
Filter Element, Spin On, BE-25-25 Zinga
4
Kit, Hydro Oil Repl 2 1/2 Gal 3372
028535
Oil, Shell TTF-SB
P620
Filter Element, Spin On, BE-25-25 Zinga
040642
3-2
DESCRIPTION
1 2.5 gal 2 1
Oil,TTF-SB 32oz Bottle Hydro
028535
Oil, Shell TTF-SB
1 qt
040630
Decal, Hydraulic TTF-SB Oil
1
040635
Black Cap, for 32oz. Bottle Oil Container
1
040636
Bottle, 32oz. Container for Oil
1
040637
Spout Cap/ W Red Seal for 32oz Container
1
047600
Kit, Hydro-Gear Flow Test
048400
Seal Kit, Hydro-Gear BDP 10-12
1
Lastec//042315
Seal kit for Pumps
1
Hydraulic System
Hydraulic System Hydraulic Layout Diagram
3
Cooler
Tank Filter Filter
Pump Motor Pump
2261_003
Motor
Hydraulic System
Lastec//042315
3-3
3 3.2 REF
Hydraulic System Hydraulic Pump Assemblies
Hydraulic Pump Assemblies PART #
DESCRIPTION
COMMENTS
040379
Pump Assembly, 12cc Right Hydro
Right Side Only
040378
Pump Assembly, 12cc Left Hydro
Left Side Only
QTY. 1
1
019359
Bushing, 15MM Split Taper
1
2
F05011-14
Washer, 1/4” Split Lock
2
3
F05005-101
Bolt, 1/4-20 x 1” Hex Head Grade 5
2
4
018773
Sheave, BK60 QT
1
5
048532
Key, 5MM x 5MM x 25MM
1
6
F05007-208
Screw, 3/8-16 x 1-1/2” FHS
2
7
F05011-3
Washer, 3/8” Flat SAE
2
8
F05010-10
Nut, 3/8-16 Hex Nyloc
9
040272
Pump, 12cc Right Hydro
Right Side Only
2
040273
Pump, 12cc Left Hydro
Left Side Only
10
026393
Fitting, #8 SAE / #8 JIC 90 X-L Elbow
2
1 1
11
P12722
Fitting, #6 90Deg SAE #6 Hose Barb Hyd.
1
12
F05008-96
Bolt, 5/16-18 x 1 1/2” Hex Head Grade 5
1
13
040396
Spacer Hydro Actuator
1
14
F05010-58
Nut, 5/16-18 Nylok Hex
1
040376
Belt, AX-60
Not Shown
1
046487
Actuator Kit, 3386 RTN
Parts not sold separately
1
NOTE: Left and Right Pump Assemblies are mirror images of each other.
3-4
Lastec//042315
Hydraulic System
Hydraulic System Hydraulic Pump Assemblies
3
.
2261_004
Hydraulic System
Lastec//042315
3-5
3 3.3 REF
Hydraulic System Hydraulic Motor, Right
Hydraulic Motor, Right PART #
DESCRIPTION
049965
Wheel/Motor Assembly, 2861 Right Rear
1
P04646
Nut, 1/2-20 Lug
2
F05011-115
Washer, 1” ID .03 SS Shim
3
F05011-116
Washer, 1” ID .06 SS Shim
4
043320
Brake Assembly, 3377TZ Rear Drum
QTY. 1
Torque to 144 ft.-lbs.
5 As Req’d As Req’d
See Section 3.5 for parts
1
043320-1
Drum, 152.4mm w/Studs
1
043320-2
Brake, 152.4 x 25 Cam
1
5
F05010-121
Nut, 5/16-18 Nylon Locking Jam
1
6
F05011-16
Washer, 5/16” Standard Flat
1
7
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc
1
8
F05006-117
Bolt, 5/16-18 x 3/4” SHC SS
4
9
F05011-13
Washer, 5/16” Split Lock
4
10
F05008-28
Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5
4
11
F05010-8
Nut, 1/2-13 Nyl Hex Lock
4
12
F05011-101
Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard)
4
13
071864 1
Fitting, 8 ORFS - 10 STOR 90
2
14
F05007-123
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
15
055177
Plate, E-Brake Pulley Right
Serial # 2760706 and later
1
Serial # 2750706 and prior
1
1
027056
Plate, E-Brake Pulley Right
16
F05011-3
Washer, 3/8” Flat SAE
17
026409
Pulley, E-Brake
1
18
055151
Plate, E-Brake Cable Retaining
1
2
19
F05010-124
Nut, 3/8-16 Half Nyloc
1
20
F05012-49
Pin, 1/8” x 1 1/2” Cotter
1
21
046659
Motor, Right Hydro-Gear Drive
1
22
046800
23
026417 026439
1
COMMENTS
1
Key, 5/16” x 1” Woodruff
1
Hex Nut, 1-20 Slotted Tire Assembly, 24” x 12-12 Turf Master
Not Shown
1
041098-1
Tire, 24” x 12-12 (Tire Only)
1
026440
Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC
1
071864 replaced (2) 072561 Fitting, 8 ORFS - 10 STOR 45 (Serial #47960513 and later). 072561 replaced (2) 016807 Fitting, #10 SAE-1/2” JIC 45 Elbow (Serial #46570113 to #47950513).
3-6
Lastec//042315
Hydraulic System
Hydraulic System Hydraulic Motor, Right
3
LT0069C
Hydraulic System
Lastec//042315
3-7
3 3.4 REF
Hydraulic System Hydraulic Motor, Left
Hydraulic Motor, Left PART #
DESCRIPTION
049966
Wheel/Motor Assembly, 2861 Left Rear
1
P04646
Nut, 1/2-20 Lug
2
F05011-115
Washer, 1” ID .03 SS Shim
3
F05011-116
Washer, 1” ID .06 SS Shim
4
043320
Brake Assembly, 3377TZ Rear Drum
QTY. 1
Torque to 144 ft.-lbs.
5 As Req’d As Req’d
See Section 3.5 for parts
1
043320-1
Drum, 152.4mm w/Studs
1
043320-2
Brake, 152.4 x 25 Cam
1
5
F05010-121
Nut, 5/16-18 Nylon Locking Jam
1
6
F05011-16
Washer, 5/16” Standard Flat
1
7
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc
1
8
F05006-117
Bolt, 5/16-18 x 3/4” SHC SS
4
9
F05011-13
Washer, 5/16” Split Lock
4
10
F05008-28
Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5
4
11
F05010-8
Nut, 1/2-13 Nyl Hex Lock
4
12
F05011-101
Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard)
4
13
071864 1
Fitting, 8 ORFS - 10 STOR 90
2
14
F05007-123
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
3
15
F05007-124
Bolt, 3/8-16 x 2” Hex Head Grade 5
1
16
055178
Plate, E-brake Pulley Left
Serial # 2760706 and later
1
027057
Plate, E-brake Pulley Left
Serial # 2750706 and prior
1
17
F05011-3
Washer, 3/8” Flat SAE
6
18
026409
Pulley, E-Brake
3
19
055151
Plate, E-Brake Cable Retaining
3
20
F05010-124
Nut, 3/8-16 Half Nyloc
3
21
F05012-49
Pin, 1/8” x 1 1/2” Cotter
1
22
046661
Motor, Hydro Gear
1
23
046800
Key, 5/16” x 1” Woodruff
1
24
026417
Hex Nut, 1-20 Slotted
1
026439
1
COMMENTS
Tire Assembly, 24” x 12-12 Turf Master
Not Shown
1
041098-1
Tire, 24” x 12-12 (Tire Only)
1
026440
Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC
1
071864 replaced (2) 072561 Fitting, 8 ORFS - 10 STOR 45 (Serial #47960513 and later). 072561 replaced (2) 016807 Fitting, #10 SAE-1/2” JIC 45 Elbow (Serial #46570113 to #47950513).
3-8
Lastec//042315
Hydraulic System
Hydraulic System Hydraulic Motor, Left
3
LT0070C
Hydraulic System
Lastec//042315
3-9
3 3.5 REF
Hydraulic System Brake Assembly
Brake Assembly PART #
DESCRIPTION
COMMENTS
043320
Brake Assembly, Rear Drum
Includes Items 1 to 8
1
043320-1
2
043320-4 043320-2
Drum, 152.4mm w/Studs
Includes Item 2
Stud, 1/2-20 x 1-1/4 Press In Brake, 152.4 x 25 Cam
QTY. 1 1 5
Includes Items 3 to 8
1
3
043320-9
Shoe, 152.4 x 25 Brake
2
4
043320-10
Spring, 152.4 x 25 Brake Return
2
5
043320-8
Cam, 152.4 x 25 Brake
1
6
043320-7
Backing Plate, 152.4 x 25 Brake
1
7
043320-5
Arm, 152.4 x 25 Brake Actuator
1
8
043320-6
Clip, 152.4 x 25 Retainer
1
3-10
Lastec//042315
Hydraulic System
Hydraulic System Brake Assembly
3
3300_045
Hydraulic System
Lastec//042315
3-11
3 3.6 REF
Hydraulic System Hydraulic Filter Assembly
Hydraulic Filter Assembly PART #
DESCRIPTION
042940
Filter Assembly, 22HP Commercial
COMMENTS
QTY. 1
1
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
6
2
F05011-17
Washer, 5/16” SAE Flat
6
3
049212
Bracket, Filter Mount
2
4
F05005-137
Bolt, 1/4-20 x 5/8” Hex Head Grade 5
4
5
F05011-14
Washer, 1/4” Split Lock
4
6
P12708
Fitting, 3/8NPT-3/8 Barb Elbow
2
7
061807
Hose Clamp, Dixon Worm Gear HSS6
8
8
040386
Hose, 3/8” Hyd x 25" Low Pressure
2
9
F05010-58
Nut, 5/16-18 Nyl Lock
6
10
P619
Filter Head, 3/8” NPT
2
11
048988
Fitting, 3/8” NPT - 3/8” Barb 45 Deg
2
12
P620
Filter, Spin On 25 Micron
2
13
048776
Hose, 3/8” Hyd x 14” Low Pressure
2
NOTE: Right and Left Filter Assemblies are mirror images of each other. NOTE: Filter head is flow dependant. Check flow direction before attaching hoses.
3-12
Lastec//042315
Hydraulic System
Hydraulic System Hydraulic Filter Assembly
3
2261_005
Hydraulic System
Lastec//042315
3-13
3 3.7 REF
Hydraulic System Hydraulic Tank Assembly
Hydraulic Tank Assembly PART #
DESCRIPTION
049970
Tank Assembly, 22HP Hydraulic
COMMENTS
QTY. 1
1
041083
Valve, Two Tank Diverter
2
028492
Plug, 3/8” NPT Hex Brass
1
3
049891
Hose, 3/8” Low Pressure 28"
1
4
P12724
Fitting, 3/8” NPT-3/8” Barb
2
5
043251
Bushing, Hex, 3/4” x 3/8”
1
6
P12708
Fitting, 3/8” NPT-3/8” Barb Elbow
2
7
P649
Hose Clamp, 7/32”-5/8”
2
8
047883
Tube, Vinyl Sight Gage
1
(1) removed after serial #3011006
1
9
048988
Fitting, 3/8” NPT - 3/8” Barb 45 Deg
2
10
F05011-4
Washer, 3/8” Split Lock
2
11
F05007-87
Bolt, 3/8-16 x 1” Hex Head Grade 5
2
12
028493
Fitting, 3/8” NPT F-M-F Tee
1
13
027066
Hose Assembly, 3/8” x 14-1/2”
Includes (2) fittings (P12724)
1
14
028593
Clamp, 3/4” EMT Coated
Added after serial #3011006
1
15
P04332
Cap, 3/8” Pipe Galvanize
Added after serial #3011006
1
16
049971
Tank Weldment, 2861AGC Hyd
1
17
040347
Plate Weldment, Cooler Mount
1
18
049222
Cooler, Hyd Fluid
1
19
049227
Fitting, 1/2” NPT x 3/8” Hose Elbow
2
20
F05004-1
Screw, 10-24 x 1/2” Sl Hex Machine
4
21
F05011-18
Washer, #10 SAE Flat
4
22
F05005-78
Screw, 1/4-20 x 3/8” Hex Flanged Whiz Lock
2
3-14
Lastec//042315
Hydraulic System
Hydraulic System Hydraulic Tank Assembly
3
2261_006
Hydraulic System
Lastec//042315
3-15
3
Hydraulic System
3.8
Hydraulic Idler
REF
Hydraulic Idler
PART #
DESCRIPTION
040395
Idler Assembly, Comm. Diesel Hydro Drv
COMMENTS
QTY. 1
1
F05008-23
Bolt, 1/2-13 x 3” Hex Head Grade 5
1
2
F05011-2
Washer, 1/2” SAE Flat
3
045295
Pulley Assembly, 5” OD Idler Flat
1
3
F05254-12
Ring, 62mm IR Din #472 Retaining
2
4
P103
Bearing, Spindle Top 6305 RS
1
5
045296
Pulley, 5 OD Idler, Flat
1
6
045297
Boss, Idler Pulley Standoff
1
7
047881
Idler Weldment, Comm Diesel Hydro Drive
8
P107
Fitting, 1/4-28 Straight Grease
1
9
F05010-127
Nut, 1/2-13 Half Nylon Lock
2
10
029842
Bushing, 3/4” ID x 1” OD x 1” Oil
2
11
F05011-77
Washer, 3/4” AN
2
1
12
F05010-127
Nut, 1/2-13 Half Nylon Lock
2
13
F05011-62
Washer, 3/4” SAE Flat
1
14
040102
Pin, Idler Pivot
1
15
F05011-77
Washer, 3/4” AN
3
16
F05012-115
Pin, 3/4” Clevis Retaining
1
17
048499
Idler Adjust Weldment
1
18
059187
Bushing, Urathane Spring
1
19
F05011-2
Washer, 1/2” SAE Flat
1
3-16
Lastec//042315
Hydraulic System
Hydraulic System Hydraulic Idler
3
2261_001-3C
Hydraulic System
Lastec//042315
3-17
4
SECTION 4 ENGINE & ELECTRICAL
Lastec//042315
4-1
4 4.1 REF
4-2
Engine & Electrical Fuel Tank (Serial # 25610207 and prior)
Fuel Tank (Serial # 25610207 and prior) PART #
DESCRIPTION
COMMENTS
029436
Tank Assembly, Diesel Fuel
No longer available; order 055438 Tank Assembly
QTY. 1
1
041187
Cap, Fuel Tank w/Indicator 3 1/2”
1
2
028820
Fitting, 1/4” Barb 90 Tank
2
3
028818
Grommet, Fuel Tank Fitting
2
4
029436-1
Tank, 7 Gallon Molded Fuel
5
046532
Tubing, 1/4” x 2" Long Tygon
Internal to the tank 029436-1
1
6
043448
Tubing, 1/4” x 17” Tygon
Internal to the tank 029436-1
1
7
028821
Filter, 1/4” Barb Tank Filter
Internal to the tank 029436-1
1
1
8
085614
Grommet, Rubber 2 1/2” Dia
3
9
043441
Washer, Fuel Tank Retaining
1
10
019696
Cap, Hyd Tank (P631)
3
11
043442
Washer, Fuel Tank Double
1
12
F05004-18
Screw, 10-24 x 5/8 Unsl Indent HH Machine
Serial # 4980105 and later
2
F04203-3
Rivet, Self Sealing
Serial #4970105 and prior
2
13
045897
Plate, Decal Fuel
14
F05011-20
Washer, #10 Split Lock
Added after Serial # 4980105
2
1
Lastec//042315
Engine & Electrical
Engine & Electrical Fuel Tank (Serial # 25610207 and prior)
4
LT0099
Engine & Electrical
Lastec//042315
4-3
4 4.2 REF
Engine & Electrical Fuel Tank Assembly
Fuel Tank Assembly PART # 047539
COMMENTS
QTY.
Tank Assembly, Diesel Dual Fittings
1
1
045897
Plate, Decal Fuel
1
2
F05004-18
Screw, 10-24 x 5/8” Unsl Indent HH Machine
2
3
F05011-20
Washer, #10 Split Lock
2
4
085614
Grommet, Rubber 2 1/2” Dia
3
5
043441
Washer, Fuel Tank Retaining
1
6
019696
Cap, Hydraulic Tank (P631)
3
7
043442
Washer, Fuel Tank Double
1
073230
Tank Assembly, 7 Gallon Diesel Dual Fitting
8
Includes Fuel Tank
1
073228
Gauge, Fuel Indicator Threaded Sealed
1
9
073229
Nut, Fuel Gauge
1
10
026402
Plug, Fuel Tank
1
11
028818
Grommet, Fuel Tank Fitting
1
12
063251
Cap, Diesel Fuel Tank Vented
1
13
064652 067774
1
DESCRIPTION 1
Fitting, Fuel 1/4 Bulkhead w/ Screen Fitting, 3/16 Barb 90 Tank W/ 2" Tube
1 Not Shown - Right Tank Only
1
073230 replaced 072860 7 Gallon Diesel Dual Fitting Tank Assembly (including 072735 Gauge,072736 Grommet, 049809 Fitting, (2) 028818 Grommets, 055446 Tube) (1/15). 072860 replaced 055438 Fuel Dual Fitting Tank Assembly (9/14). 049809 Fitting replaced 1/4” Barb 90 Tank Fitting (028820) and 1/4” x 2" Long Tygon Tubing (046532) on units with serial #39030111 and later.
4-4
Lastec//042315
Engine & Electrical
Engine & Electrical Fuel Tank Assembly
4
LT0040C
Engine & Electrical
Lastec//042315
4-5
4 4.3
Engine & Electrical Fuel System
Fuel System
REF
PART #
DESCRIPTION
1
045586
Hose, 1/4” x 41” Fuel
1
2
040389
Hose, Fuel 1/4” x 28"
1
3
049859
Hose, Fuel 1/4” x 12-1/2”
2
4
045967
Hose, Fuel 1/4” x 8-1/2”
1
5
040388
Hose, Fuel 1/4” x 32"
2
6
041083
Valve, Two Tank Diverter
P649
Hose Clamp, 7/32”-5/8”
4-6
COMMENTS
QTY.
1 Not Shown
Lastec//042315
14
Engine & Electrical
Engine & Electrical Fuel System
4
2261_012
Engine & Electrical
Lastec//042315
4-7
4 4.4
Engine & Electrical Engine Assembly
Engine Assembly PART #
DESCRIPTION
COMMENTS
049974
Engine, 22HP Yanmar Diesel
044641
Altenator, Yanmar, 3TVN70-ASA
044642
Gasket, Valve Cover, 3TNV70-ASA
044643
Gasket, Engine Set, Yanmar,3TNV70
044644
Seal, Front Main,Yanmar,3TNV70-ASA
044646
Injector Assy, Yanmar, 3TNV70-ASA
044647
Filter, Oil, Yanmar, 3TNV70-ASA
044648
Switch, Oil Pressure, Yanmar, 3TNV70-ASA
044649
Seal, Rear Main, Yanmar, 3TNV70-ASA
044650
Motor, Starter, Yanmar, 3TNV70-ASA
044651
Thermostat, Yanmar, 3TNV70-ASA
044652
Thermostat Gasket, Yanmar TNV
044653
Pump, Water Assy, Yanmar, 3TNV70-ASA
044654
Gasket, Water Pump, Yanmar, 3TNV70-ASA
044655
Sender, Water Temp, Yanmar, TNV88/TNV70
044656
Solenoid, Fuel, Yanmar, TNV88/TNV70
044657
Diode, Solenoid Relay, Yanmar 3TNV88/70
044658
Timer, Yanmar, 3TNV70-ASA
044659
Gasket, Exhaust, Yanmar, 3TNV70-ASA
044661
Fan, Radiator, Yanmar, 3TNV70-ASA
044662
Gasket, Head, Yanmar, 3TNV70-ASA
044663
Plug, Oil Drain, Yanmar, 3TNV70-ASA
044664
Seal, Oil Drain, Yanmar, 3TNV70-ASA
044665
Plug, Glow, Yanmar, 3TNV70-ASA
044666
Gasket, Manifold, Yanmar, 3TNV70-ASA
044667
Dipstick, Yanmar, 3TNV70-ASA
044668
Fan Belt, Yanmar TNV
044669
Pipe, Fuel Return, Yanmar, 3TNV70-ASA
044671
Kit, Radiator, Yanmar, 3TNV70-ASA
072871
Fuel Pump, Yanmar Diesel 3TNV70
072872
Gasket, Fuel Pump Yanmar 3TNV70
056587
Fuel Strainer, Yanmar
044645
Filter, Fuel, 22HP Yanmar,3TNV-70
056586
O-Ring, Yanmar
056585
Spring, Fuel Strainer, Yanmar
NOTE: See the Yanmar Service Manual for more details.
4-8
Lastec//042315
Engine & Electrical
Engine & Electrical Engine Assembly
4
2261_007-1
Engine & Electrical
Lastec//042315
4-9
4
Engine & Electrical
4.5
Clutch Assembly
Clutch Assembly
REF
PART #
DESCRIPTION
1
042931
Mount Weldment, Throttle Cable
COMMENTS
QTY. 1
2
F05004-230
Screw, M8-1.25 x 16 Hx Flange Serr
2
3
040373
Shaft, 61AC Diesel Stub
1
4
F05004-97
Screw, M10x1.5 x 35MM Hex Head
6
5
F05011-88
Washer, 10mm Split Lock
6
6
047519
Belt, B120 Drive
73” Deck Only
1
049255
Belt, B124 Wrapped
61” Deck Only
1
040313
Clutch Assembly, 5.75 Pitch 1 1/8 Bore 12V
1
7
F05010-58
Nut, 5/16-18 Nylok Hex
8
F05011-17
Washer, 5/16” SAE Flat
4
9
040311
Clutch, 5.75 Dia x 1 1/8 Bore 12V
1
10
040338
Weldment, Clutch Stop
1
11
F05011-33
Washer, 5/16” Star ET
2
12
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
2
13
F05010-124
Nut, 3/8-16 Half Nyloc
2
14
F05011-3
Washer, 3/8” Flat SAE
1
15
044683
Hose, Clutch Stop Bushing
1
16
S12284
Tube, 7/8 Dia Elec Motor Spacer
1
17
040340
Capture Weldment, Clutch Stop
1
18
048166
Washer, Clutch Capture
1
19
F05011-48
Washer, 7/16” Split Lock
1
20
F05007-156
Bolt, 7/16-20 x 1 1/2” Hex Head Grade 5
1
4-10
1
Lastec//042315
Engine & Electrical
Engine & Electrical Clutch Assembly
4
2261_007-2
Engine & Electrical
Lastec//042315
4-11
4 4.6 REF
Engine & Electrical Clutch Guard
Clutch Guard PART #
DESCRIPTION
040374
Guard Assembly, 22HP Yanmar
COMMENTS
QTY. 1
1
F05007-129
Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5
2
2
040334
Guard Weldment, 22HP Clutch
1
3
F05010-160
Nut, #10-24 Hex Self-Locking
1
4
P06104
Foot, Rubber
1
5
F05004-35
Bolt, #10-24 x 1/2” Socket BH
1
6
F05010-10
Nut, #10-24 Hex Self-Locking
2
7
027006
Spring, 1 1/8” x 7 1/2” x .091” Ext
1
8
040384
Weather Strip, Belt Cover
1
4-12
Lastec//042315
Engine & Electrical
Engine & Electrical Clutch Guard
4
2261_008
Engine & Electrical
Lastec//042315
4-13
4 4.7 REF
Engine & Electrical Air Cleaner
Air Cleaner PART #
DESCRIPTION
055382
Filter, Kohler Air Intake Fixed Mount
COMMENTS
QTY. 1
046552
Housing Cap, Kohler Filter
073357
Housing Cap Dirt Ejector, Kohler Filter
2
046553
Air Filter, Primary Element
1
3
046554
Air Filter, Inner Element
1
4
046551
Housing Cover, Kohler Filter
1
5
046555
Plug,Kohler Filter Minder
1
6
P09895
Clamp, Worm, 2 1/2”
1
7
046556
Hood, Rain
1
1
072827
Cover Assembly, Air Cleaner
1 Not Shown
Not Shown
1
1
8
043274
Plate, Air Breather Mount
1
9
F05004-230
Screw, M8-1.25 x 16 Hx Flange Serr
4
10
F05011-45
Washer, 8mm Split Lock
2
11
F05004-40
Bolt, M8 x 1.25 x 1 C/S 8.8 Din 933
2
12
F05010-162
Nut, M8 x 1.25 Free
1
13
P09895
Clamp, Worm, 2 1/2”
2
14
029559
Hose, Kubota Air Breather
1
4-14
Lastec//042315
Engine & Electrical
Engine & Electrical Air Cleaner
4
2261_007-3
Engine & Electrical
Lastec//042315
4-15
4 4.8 REF
Engine & Electrical Fuel Separator Assembly
Fuel Separator Assembly PART #
DESCRIPTION
055453
Separator Assembly, Water & Fuel
COMMENTS
QTY. 1
1
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
2
2
F05011-17
Washer, 5/16” SAE Flat
2
3
040346
Bracket Weldment, Water Separator
1
4
F05010-58
Nut, 5/16-18 Nylok Hex
2
5
026399
Spacer, Hydro Actuator
1
6
040345
Separator, Fuel/Water
1
056586
O-Ring, Yanmar
1
044673
Water Separator, Screen, 3TNV70-ASA
1
056589
Spring, Separator, Yanmar
1
056590
Float, Separator, Yanmar
1
7
F05011-13
Washer, 5/16” Split Lock
1
8
F05006-3
Bolt, 5/16-18 x 3 1/2” Hex Head Full Thread
1
9
048904
4-16
Throttle Fitting, Swivel
1
Lastec//042315
Engine & Electrical
Engine & Electrical Fuel Separator Assembly
4
2261_009
Engine & Electrical
Lastec//042315
4-17
4 4.9 REF
Engine & Electrical Motor Mount
Motor Mount PART #
DESCRIPTION
049951
Mount Assembly, 22HP Yanmar Engine
COMMENTS
QTY. 2
1
F05008-61
Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5
4
2
018751
Washer, Motor Mount
4
3
049952
Mount Weldment, 22HP Yanmar
4
F05004-48
Bolt, M10-1.5 x 25mm Hex Head FT 8.8 Znc
Metric
8
5
F05011-88
Washer, 10mm Split Lock
Metric. Use Loctite 242 on threads
8
6
018734
Bushing, Kubota Rubber Mount
4
7
F05010-8
Nut, 1/2-13 Nyl Hex Lock
4
4-18
Lastec//042315
1
Engine & Electrical
Engine & Electrical Motor Mount
4
2261_007-5
Engine & Electrical
Lastec//042315
4-19
4
Engine & Electrical Engine Assembly Mount
4.10 Engine Assembly Mount REF
PART #
DESCRIPTION
COMMENTS
QTY
1
049957
Mount Weldment, 22HP Yanmar Engine
1
2
F05008-10
Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5
1
3
F05011-2
Washer, 1/2” SAE Flat
1
4
040382
Pulley, 5” Crowned Idler
1
5
F05010-8
Nut, 1/2-13 Nylon Hex Lock
1
6
042925
Idler Assembly, Deck Drive
047523
Idler Assembly, Fixed Mule Drive
See Section 4.11 for parts
1 1
7
047591
Bracket, Fixed Idler Mount
1
8
F05008-37
Bolt, 1/2-13 x 1 1/4“ Hex Head Grade 5
4
9
F05010-127
Nut, 1/2-13 Half Nylock, Znc
5
10
F05008-102
Bolt, 1/2-13 x 2” Hex Head Grade 5
1
11
F05011-68
Washer, 1/2” Standard Flat
1
045271
Pulley Assembly, 5” OD idler
1
12
F04254-12
Ring, 62MM IR
2
13
P103
Bearing, Spindle Top 6305 RS
1
14
045270
Pulley, 5 OD Idler
1
15
045272
Boss, Idler Pulley Standoff
1
16
F05007-109
Bolt, 3/8-16 x 4 3/4” Hex Head Grade 5
4
17
F05011-3
Washer, 3/8” Flat
4
18
F05010-10
Nut, 3/8-16 Hex Nylon Lock
4
4-20
Lastec//042315
Engine & Electrical
Engine & Electrical Engine Assembly Mount
4
2261_001-1
Engine & Electrical
Lastec//042315
4-21
4
Engine & Electrical Idler, Deck Drive
4.11 Idler, Deck Drive REF
PART #
042925
DESCRIPTION
COMMENTS
QTY
Idler Assembly, Deck Drive
1
1
F05008-37
Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 Zinc
2
2
047526
Pivot Weldment, Mule Drv Tnsnr
1
3
F05010-127
Nut, 1/2-13 Half Nylock, Znc
2
4
F05008-10
Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5
1
F05011-68
Washer, 1/2 Standard Flat
1
045271
Pulley Assembly, 5” OD Idler
1
5 6
F04254-12
Ring, 62MM IR
2
7
P103
Bearing, Spindle Top 6305 RS
1
8
045270
Pulley, 5” OD Idler
1
9
045272
Boss, Idler Pulley Standoff
1
10
042922
Idler Weldment, Deck Drive
1
11
049277
Bearing Half, Urethane Bushed
1
12
042926
Boss Weldment, Rubber Spring Tensioner
1
13
T215
Spacer, 3/4” OD x 25/64” ID x 3/4” Lng
1
14
F05011-104
Washer, 3/8” x 1 1/2” x 1/8” Znc H
1
15
F05011-4
Washer, 3/8” Split Lock
1
16
F05007-207
Bolt, 3/8-16 x 1 3/4” Hex Head Grade 8
1
17
F05012-115
Pin, 3/4” Clevis Retaining
1
18
P786
Bushing,3/4” ID x 1” OD x 5/8” Lng Flgd
2
19
P107
Fitting, 1/4-28 Straight Grease
1
20
F05010-8
Nut, 1/2-13 Nylon Hex Lock
1
21
F05010-35
Nut, 1/2-13 Free Hex, Zinc
2
22
F05011-68
Washer, 1/2” Standard Flat
Serial #27280507 and later
1
F05011-2
Washer, 1/2” SAE Flat
Serial #27270507 and prior
1
042928
Spring, Urethane
23
1
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
4-22
Lastec//042315
Engine & Electrical
Engine & Electrical Idler, Deck Drive
4
2261_001-2
Engine & Electrical
Lastec//042315
4-23
4
Engine & Electrical Radiator Assembly
4.12 Radiator Assembly REF
PART #
DESCRIPTION
040367
Radiator Assembly, 2261
COMMENTS
QTY. 1
1
047534
Screen Weldment, 33HP Radiator
1
2
040394
Weather Strip, Radiator Screen
2
3
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head
4
4
F05011-13
Washer, 5/16” Split Lock
2
5
F05011-17
Washer, 5/16” SAE Flat
6
6
040351
Bracket, Top Radiator Mount
1
7
F05007-118
Bolt, 3/8-16 x 3/4” Hex Head Grade 5
3
8
F05011-4
Washer, 3/8” Split Lock
3
9
028217
Bushing, Rubber Radiator Mount
3
10
F05010-10
Nut, 3/8-16 Hex Nyl Lock
1
11
040391
Guard Weldment, Left Radiator Screen
1
12
040390
Guard Weldment, Right Radiator Screen
1
13
F05010-58
Nut, 5/16-18 Nyl Lock
2
14
040387
Bottle Assembly, 22HP Yanmar
1
15
040354
Plenum Weldment, Upper Radiator
1
16
040368
Plenum Weldment, Lower Radiator
1
17
028352
Clamp,1” ID Coated
1
18
F05005-137
Bolt, 1/4-20 x 5/8” Hex Head Grade 5
8
19
F05011-14
Washer, 1/4” Split Lock
8
20
F05011-11
Washer, 1/4” SAE Flat
8
21
042935
Radiator, 22HP Yanmar
1
22
044660
Cap, Radiator
1
23
043273
Bracket, Side Radiator Mount
2
24
049999
Bracket, Bottom Radiator Mount
1
25
F05005-78
Screw, 1/4-20 x 3/8” Hex Flanged Whiz Lock
6
26
F05007-118
Bolt, 3/8-16 x 3/4” Hex Head Grade 5
3
27
042977
Plate, Radiator Mount
1
28
F05010-124
Nut, 3/8-16 Half Nylock
2
29
F05011-9
Washer, 1/2” Split Lock
2
30
F05008-101
Bolt, 1/2-13 x 3/4” Hex Head Grade 5
2
31
P07584
Clamp, 1/2” EMT Coated
1
32
040314
33 34
4-24
Hose, Lower Radiator
1
040200
Clamp, 1 3/4” Worm
4
040315
Hose, Upper Radiator
1
Lastec//042315
Engine & Electrical
Engine & Electrical Radiator Assembly
4
2261_010
Engine & Electrical
Lastec//042315
4-25
4
Engine & Electrical Exhaust System
4.13 Exhaust System REF
PART #
DESCRIPTION
1
040356
Shield Weldment, Muffler
COMMENTS
QTY.
2
F05007-118
Bolt, 3/8-16 x 3/4” Hex Head Grade 5
3
3
F05011-4
Washer, 3/8” Split Lock
3
1
4
F05011-3
Washer, 3/8” Flat SAE
3
5
048120
Weldment, Muffler
1
6
F05004-40
Bolt, M8 x 1.25 x 1 C/S 8.8 Din 933 HH
4
7
028513
Gasket, Exhaust Kubota
1
8
042938
Exhaust Pipe, 22HP Yanmar
1
9
F05011-45
Washer, 8mm Split Lock
8
10
F05010-162
Nut, M8x1.25 Free Zinc Plate
8
11
040366
Mount Bracket, Muffler Heat Shield
1
12
F05007-87
Bolt, 3/8-16 x 1” Hex Head Grade 5
3
13
040360
Plate Weldment, Muffler Mount
1
14
F05004-232
Bolt, M12 x 1.25 x 40mm Hex Head
2
15
F05010-1
Nut, 3/8-16 Hex
3
4-26
Lastec//042315
Engine & Electrical
Engine & Electrical Exhaust System
4
2261_007-4
Engine & Electrical
Lastec//042315
4-27
4
Engine & Electrical Battery Box Assembly
4.14 Battery Box Assembly REF
PART #
DESCRIPTION
040321
Battery Assembly, 22HP Yanmar
047581 1
COMMENTS
Battery Assembly, 33Hp
QTY. 1 1
016413
Box, Battery Modified
1
2
F05006-123
Bolt, 5/16-18 x 8-1/2” Hex Head Grade 5
2
3
026382
Angle, Battery Hold Down
1
4
P12161
Washer, Felt Battery Terminal
1
5
067381
Battery, Group 26 w/Handle
1
6
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
2
7
F05011-17
Washer, 5/16” SAE Flat
2
8
F05005-124
Bolt, 1/4-20 x 1 1/2” Hex Head Grade 5
1
9
F05011-11
Washer, 1/4” SAE Flat
1
10
F05010-69
Nut, 1/4-20 Nylock
1
11
F05010-58
Nut, 5/16-18 Nylok Hex
4
12
P11258
Strap, 24” Rubber With Hooks
1
13
F05005-123
Bolt, 1/4-20 x 3/4” Hex Head Grade 5
2
14
049987
Tray Weldment, Battery Mount
1
15
F05010-9
Nut, 1/4-20 Keps
4
16
F05011-11
Washer, 1/4” SAE Flat
2
4-28
Lastec//042315
Engine & Electrical
Engine & Electrical Battery Box Assembly
4
2261_011
Engine & Electrical
Lastec//042315
4-29
4
Engine & Electrical Electrical Harness
4.15 Electrical Harness Harness Color Code Matrix, Rev. B.02, Lastec Item # 055700
4-30
Wire #
Gauge
Color/Stripe
From - To
1A-B
4
Red
Bat +, Starter
1C-D
14
Red
Starter, Alt
2A-B
4
Black
Bat (neg), Eng Gnd Fuel Solenoid, Clutch
2C-D
16
Black
2E-F
16
Black
Clutch, Engine Diode
2G-H
16
Black
Engine Diode, Engine Ground Engine Ground, Timer
2I-J
16
Black
2K-L
16
Black
Timer, Splice
2M-N
16
Black
Splice, Seat Delay Seat Delay, CR3-86
2O-P
14
Black
2Q-R
16
Black
CR3-86, CR2-86
2S-T
16
Black
CR2-86, CR1-86
2U-V
16
Black
Splice, Power Outlet gnd
2W-X
16
Black
Power Outlet gnd, Hr. Meter (-) Key 30, F1 Fuse
3A-B
14
Red
3C-D
14
Red
F1 Fuse, Alt
4A-B
14
Yellow/White
Key - 19, Glow
5A-B
16
Red/Yellow
CR1 - 87, Engine Diode
5C-D
16
Red/Yellow
Engine Diode, Fuel Solenoid (Hold)
6A-B
12
Orange
CR4-87, Fuel Solenoid (Pull)
7A-B
16
Red/White
CR4-86, Timer
8A-B
16
Yellow
CR4-85, Timer
9A-B
16
Red/Black
Key AC, CR2-30
9C-D
16
Red/Black
CR2 - 30, F3 Fuse
9E-F
16
Red/Black
F3 Fuse, Alt Exciter
9G-H
16
Red/Black
Key AC, CR5-30
9I-J
16
Red/Black
CR5 - 30, CR5-85
9K-L
16
Red/Black
CR5 - 85, Splice
9M-N
16
Red/Black
Splice, Oil Light
9O-P
16
Red/Black
Splice, Water Light
9Q-R
16
Red/Black
Splice, Blade Switch - C Splice, Brake 1
9S-T
16
Red/Black
9U-V
16
Red/Black
Brake 1, Seat
9W-X
16
Red/Black
Splice, Alarm F3 Fuse, CR1-30
10A-B
16
Red/Black
10C-D
16
Red/Black
CR1-30, CR4-30
11A-B
16
Green
Brake2, CR3 - 85
12A-B
16
White/Blue
Blade Sw NC- B, Brake 1
13A-B
16
Yellow
CR2 - 87, Clutch
14A-B
16
Red/Green
Key - 50, CR3 - 30
15A-B
16
Blue
CR3 - 87, Timer
15C-D
16
Blue
Timer, Starter Solenoid
16A-B
16
Violet/White
Blade Sw NC - C, Right Neutral
17A-B
16
Orange
Right Neutral, Left Neutral
18A-B
16
Orange/White
Left Neutral, Brake2
19A-B
16
Green/White
Blade Switch - B, Right Neutral
19C-D
16
Green/White
Right Neutral, Brake 1
19E-F
16
Green/White
Brake1 - NC, Seat
20A-B
16
Yellow/Black
Right Neutral, Left Neutral
21A-B
16
White
Left Neutral, Brake 1
21C-D
16
White
Brake 1, Clutch Diode (-) Clutch Diode (+), Seat Delay
21E-F
16
White
21G-H
16
White
Seat Delay, CR1-85
22A-B
16
Red/White
CR5 - 87A, Hour Meter (+) CR5 - 86, Oil Press
23A-B
16
Gray
23C-D
16
Gray
CR5 - 86, Oil Light
24A-B
16
Violet
Alarm, Water Temp
24C-D
16
Violet
Alarm, Water Light
25A-B
16
Green/Orange
Blade Switch NO - B, CR2-85
Lastec//042315
Notes
Engine & Electrical
Engine & Electrical Electrical Harness
4
Serial #36050110 and prior 19 30 AC 17 50 preheat off on start
3 0 1 2 Key Switch
Batt Gnd yel/wht
19
Glow Plugs
Starter/Batt Alternator Regulator EX
red
blk
30A F1 R
Water Temp vio
red
Alarm R
Oil Press red/blk
85
30
CR5
86
Blade SW
RN
vio/wht
com C
AC
gry
LN
org
org/wht
Seat
red/blk
Brake1
red/blk
grn
85 CR3 86
blk
OFF
OFF
50
Start
Brake2
wht/blu
RN
grn/wht
Blade SW com B
OFF
yel/blk
LN
D2 wht
Run 85 CR1 86
blk
DELAY
Brake1 OFF
OFF
10A
Clutch
Blade SW com B
F2
grn/org
85 CR2 86
blk
OFF CR5 red/blk
30
87A
red/wht
Hour Meter
Clutch
CR2 red/blk
30
F3 20A
87
blk
yel
FUEL (hold)
CR1 red
30
87
red/yel
D1
blk
CR4 blu blk
Fuel Pull Timer
yel
85
86
red/wht CR4 30
87
FUEL (pull) org
CR3 red/grn
30
Starter blu
87
2261 Yanmar Mower
Engine & Electrical
blk
Lastec//042315
Harness P/N ______ Rev B.02
4-31
Serial #36060110 and later
19 30 AC 17 50 preheat off on start
3 0 1 2 Key Switch
Batt Gnd yel/wht
19
Glow Plugs
Starter/Batt Alternator Regulator EX
red
blk
30A F1 R
Water Temp vio
red
Alarm R
Oil Press red/blk
85
30
CR5
86
Blade SW vio/wht
com C
AC
gry
RN
LN
org
org/wht
Seat
red/blk
Brake1
red/blk
wht/blu
RN
grn/wht
yel/blk
Blade SW com B
OFF
10A
grn
85
86
blk
85 CR1 86
blk
CR3
OFF
OFF
50
Start
Brake2
wht
OFF
OFF
Blade SW com B
Clutch
Wing red/blu
grn/org
red/wht
87A
86
blk
blk
Clutch yel
87
F4
red/blk
CR2
Hour Meter
CR2 30
85
OFF
CR5 30
red/blk
Run
DELAY
Brake1
F2
red/blk
D2
LN
blk
red/blk
blk
Fuel Pump
5A CR1
F3
red
30
87
FUEL (hold) red/yel
20A
D1
blk
CR4 blu blk
Fuel Pull Timer
yel
85
86
red/wht CR4 30
87
FUEL (pull) org
CR3 red/grn
30
Starter blu
87
36HP/22HP Yanmar Mower
Harness P/N 055700 Rev C.01
055700 rev C.01
B
14A
3A
Lastec//042315 4"
24D
9M,O,Q
9N
9X #8 Ring x2
8"
20A
19B,C
9L,S,W
NONO
Right Neutral
9"
Alarm 24A,C
22A
9J,K
Splice
4"
Oil Light
23D
3"-(tape- 2")
3/16 FI Quicks Female x4
9P
3"-(tape-2")
4"(ta pe -3")
Water Light
#10 NI Ring x4
19
AC
50
30
5" (tape)
Key 9A,G Switch 4A
22B
5" tape
87
87A
30 85
9H,I
16B
17A
9V
24"
Seat
¼" FI Quick Female x2
19F
1"
1/4" Loom 53“
21A
20B
NONO
4"
NONO
2T
5"
11A
5A
86
9B,C
21H
2R,S
CR2
87
CR1
87A
30
87
86
87A
30 85
10B,C
3/4" Loom
1" Tape
1"
+
21E
Tape
-
21D
¼" FI Quick Female x2
Diode
+
13A
85
25B
15A
86
87
87A
30 85
14B
Tape
11B
CR3
2P,Q
10"
21F,G
Complete Harness, 2261-3600 Lastec Item # 055700 Rev B.02
2N,O
10D
8B
2J,K
30 85
87
87A
4"
5"
6A
8A
Black Boot
5" Tape- 4"
4" (x2)
9D,E
2 1/2"
1"
Red Boot
2A Battery -
Metro p/n M23500
7B
4"
Tape
10A
2H,I
Starter
3C
3B
2"
Metro p/n M23501
1"
Tape
5B,C
10 "
6B
All Loom Must Be High Temperature Identified With Stripe
***except relay sockets***
Connectors viewed from wire entry
Tape All Loom Ends
Glow Plugs
13B
Clutch
2D,E
Fuel Solenoid
4B
1/4" NI Ring
Oil Pressure
Engine Diode
1"
2C
3/16" Female Bullet
23B
NOTE:
2F,G
5D
14"
1/4" Loom
2"
Tape
Tape
1"
Tape
3/16" Female Bullet
Red Boot
7 1/2"
13 1/2"
1 1/2"
4 1/2"
4"
15"
1A Battery +
38"
2 1/2"
4"
4 1/2"
3"
15D
Starter Solenoid 5/16" NI Ring 1B,C
F1 30-Amp F3 20-Amp
2B
1/2" NI Ring (x2)
Engine Ground
9F 3"
3 2 1
1/4" Loom 21"
11/2"
15B,C
Timer
2"
¼" NI Ring
Red Boot 1D,3D
Splice 2M,U 2L
CR4
86
7A
Seat Delay
!!! Sockets Viewed from Relay Insertion !!!
Brake2
18B
Tape x2
4"
3"
NONC
19D,E
9T,U
18A
17B
Brake1
21B,C
NC
12B
12"
Left Neutral
Lastec Item # 024123
sub assy.
Diode
Alt
24B
Water Temp
1/2" Loom
Wire & Connector Matrix
9R C
25A NO
16A
12A
Blade Switch
A
NO
NC
2V,W
86
23A,C
CR5
¼" FI Quick Female
-
Diode
Fuse
NC
Hr. Meter
2X
¼" FI Quick Female x3
sub assy.
Fuse
+
Power Outlet
Lastec Item # 052131
Power Outlet gnd
#10 NI Ring
AC
Alt Exciter
3/8" Loom
Key
3/8" Loom
¼" FI Quick Male x2
+
Engine & Electrical 3/4" Loom
_
1/4" Loom
-
F2 10-Amp
Engine & Electrical Electrical Harness
4
3/4" Loom
3/8" Loom
4-33
5
SECTION 5 61” MOWER DECK
Lastec//042315
5-1
5 5.1 REF 1
5-2
61 in Deck Deck Framework
Deck Framework PART # 049855
DESCRIPTION
COMMENTS
Belt, B-128 Deck Drive
QTY. 1
2
041645
Grass Chute Assembly
1
3
049490
Deck Weldment, 61” Articulating #3
1
4
049512
Deck Weldment, 61” Center
5
055835
Deck Weldment, 61” Articulating #1
Serial # 2850806 and later
1
049532
Deck Weldment, 61” Articulatin #1
Serial # 2849806and prior
1
1
Lastec//042315
61 in Deck
61 in Deck Deck Framework
5
LT0042
61 in Deck
Lastec//042315
5-3
5 5.2 REF
Deck 1 Hardware (Serial # 2860806 and later)
Deck 1 Hardware (Serial # 2860806 and later) PART #
DESCRIPTION
055834
Deck Assembly, 61” Articulating #1
COMMENTS
QTY. 1
1
F05009-20
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
2
2
F05010-185
Nut, 5/8-11 FlexLoc
2
3
055835
Deck Weldment, 61” Articulating #1
1
4
F05010-222
Nut, 3/8-16 Flanged Hex Nyloc
3
5
055803
Cover, 61A Deck #1
6 1
61 in Deck
067695
1
1
Spindle Assembly, ZT 21” D6.3-6.3
See Section 5.8 for parts
1
Replaces 049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).
5-4
Lastec//042315
61 in Deck
61 in Deck Deck 1 Hardware (Serial # 2860806 and later)
5
LT0043B
61 in Deck
Lastec//042315
5-5
5 5.3 REF 1
61 in Deck Deck 1 Hardware (Serial # 2850806 and prior)
Deck 1 Hardware (Serial # 2850806 and prior) PART # F05006-27
DESCRIPTION
COMMENTS
Bolt, 5/16-18 x 1” Hex Head Grade 5
QTY. 2
2
F05011-17
Washer, 5/16” SAE Flat
3
3
049781
Baffle, Outside Rear Bolt-On
1
4
F05010-58
Nut, 5/16-18 Nylok Hex
2
5
F05009-20
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
2
6
F05010-185
Nut, 5/8-11 FlexLoc
2
7
049532
Deck Weldment, 61 Articulatin #1
1
8
F05010-10
Nut, 3/8-16 Hex Nyloc
Added after serial # 2410406
3
9
F05011-3
Washer, 3/8” Flat SAE
Added after serial # 2410406
3
10
055803
Cover, 61A Deck #1
Added after serial # 2410406
1
NOTE: If using the rear discharge system, items 1,2,3 and 4 are not used. NOTE: After Serial # 2850806, the rear bolt-on baffle was replaced with a full pan wrap around the deck weldment.
5-6
Lastec//042315
61 in Deck
61 in Deck Deck 1 Hardware (Serial # 2850806 and prior)
5
049535
61 in Deck
Lastec//042315
5-7
5 5.4
Deck 2 Hardware
Deck 2 Hardware
REF
PART #
DESCRIPTION
1
049512
Deck Weldment, 61” Center
2
049870
Bushing, Urethane Pivot
2 Added after Serial #2790806
1
049510
Bushing, Rubber Pivot
Serial #2780806 and prior No longer available; order 049870
1
3
049894
Link, Front Deck Lift
4
4
P110
Pin, 3/8” x 1 5/16” Clevis, Yzn
2
5
P111
Ring, Kick-out, 1”
3
6
F04254-46
Ring, 3/4” External - External
1
7
F05011-77
Washer, 3/4” AN Yel/Cad
1
8
F05010-8
Nut, 1/2-13 Nylon Hex Lock
2
9
P212
Pin, 3/8” x 2 1/8” Clevis, Yzn
1
10
F05008-23
Bolt, 1/2-13 x 3” Hex Head Grade 5
1
11
F05011-9
Washer, 1/2” Split Lock
1
12
062051
Washer, Water Shed Pulley
045271
Pulley Assembly, 5” OD Idler, V Groove
Serial # 33151108 and later
1
043543
Pulley, 5” OD V-Groove Idler
No longer available: order 045271 Serial # 33141108 and prior
1
COMMENTS
QTY. 1
1
13
F04254-12
Ring, 62mm IR Din #472 Retaining
2
14
P103
Bearing, Spindle Top 6305 RS
1
15
045270
Pulley, 5” OD Idler, V Groove
1
16
045297
Boss, Idler Pulley Standoff
1
17
049868
Spacer, .53” ID x 1 1/4” OD x 1 1/4” Lng
1
18
F05007-165
Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5
2
19
F05010-222
Nut, 3/8-16 Flanged Hex Nylon Lock
2
20
049784
Baffle, Outside Rear Bolt-On
1
21
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
1
22
F05011-17
Washer, 5/16” SAE Flat
2
23
F05010-58
Nut, 5/16-18 Nylon Lock Hex
1
24
F05006-102
Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc
1
25
F05011-13
Washer, 5/16” Split Lock
1
26
027013
Wheel, Anti-Scalp, 5-5/8" hole
1
27
F05009-10
Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5
1
28
072497
Spacer, 1 OD x .65 ID x .53 Long
1
29
F05010-224
30 1
61 in Deck
067695
1
Nut, 5/8-11 Flanged Hex Nylock Spindle Assembly, ZT 21” D6.3-6.3
1 See Section 5.8 for parts
1
Replaces 049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).
NOTE: If using the rear discharge system, items 20-25 are not used. Item 2 and 8: Apply water-proof axle grease to mating surfaces prior to assembly. 5-8
Lastec//042315
61 in Deck
61 in Deck Deck 2 Hardware
5
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
LT0030B
61 in Deck
Lastec//042315
5-9
5 5.5 REF
61 in Deck Rear Discharge Baffle Assembly
Rear Discharge Baffle Assembly PART #
DESCRIPTION
049997
Baffle Kit, Rear Discharge
049963
COMMENTS
QTY. 1
Baffle Assembly, #3 Deck Mulching
1
1
F05010-222
Nut, 3/8-16 Flanged Hex Nyl Lock
2
049873
Baffle Weldment, #3 Deck Mulching
1
3
F05007-165
Bolt, 3/8-16 x 1” Carriage Grade 5
1
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
1
4
F05007-85 049961
2
Baffle Assembly, #2 Deck Rear Discharge
1
5
049960
Baffle Weldment, #2 Deck Rear Discharge
1
6
F05010-222
Nut, 3/8-16 Flanged Hex Nyl Lock
3
7
F05007-165
8
055452
Bolt, 3/8-16 x 1” Carriage Grade 5 Kit, Rear Discharge Chute
3 Serial # 2850806 and prior
1
NOTE: To use the rear discharge system, bolt in the rear discharge baffle weldments as shown here, and remove the factory installed rear baffle plates from decks 2 and 3. The factory installed baffle remains on deck 1. NOTE: All units receive the rear discharge baffles -- use of the rear discharge system is optional. Rear Chute is only for use with units with serial # 2850806 and prior.
5-10
Lastec//042315
61 in Deck
61 in Deck Rear Discharge Baffle Assembly
5
Factory installed Baffle removed
Factory installed Baffle removed
Factory installed Baffle remains
LT0048B
61 in Deck
Lastec//042315
5-11
5 5.6
61 in Deck Deck 3 Hardware
Deck 3 Hardware
REF
PART #
DESCRIPTION
049526
Deck Assembly, 61” Articulating #3
COMMENTS
QTY. 1
1
F05011-17
Washer, 5/16” SAE Flat
2
2
F05010-221
Nut, 5/16-18 Flanged Nylok Hex
2
3
F05006-27
Bolt, 5/16-18 x 1” Hex Head Grade 5
1
4
049781
Baffle, Outside Rear Bolt-On
1
5
F05009-20
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
2
6
F05010-185
Nut, 5/8-11 FlexLoc
2
7
F05006-93
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Grade 5
1
8
049490
Deck Weldment, 61” Articulating #3
1
9
055804
Cover, 61A Deck #3
1
10
F05010-222
Nut, 3/8-16 Flanged Hex Nyloc
3
11
041645
Grass Chute Assembly
See Section 5.13 for parts
1
Spindle Assembly, ZT 21” D6.3-6.3
See Section 5.8 for parts
1
12
067695
1 Replaces
1
049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).
NOTE: If using the rear discharge system, items 1,2,3 and 4 are not used.
5-12
Lastec//042315
61 in Deck
61 in Deck Deck 3 Hardware
5
LT0044-1B
61 in Deck
Lastec//042315
5-13
5 5.7 REF
61 in Deck Optional Mulching Kit
Optional Mulching Kit PART #
DESCRIPTION
049998
Baffle Kit, Mulching 61AGC
049962 1
F05010-222
COMMENTS
QTY. 1
Baffle Assembly, #2 Deck Mulching Nut, 3/8-16 Flanged Hex Nylock
1 3
2
049877
Baffle Weldment, #2 Deck Mulching
1
3
F05007-165
Bolt, 3/8-16 x 1” Carriage Grade 5
3
049964
Baffle Assembly, #1 Deck Mulching Baffle Weldment, #1 Deck Mulching
1
4
049866
5
F05010-222
Nut, 3/8-16 Flanged Hex Nylock
2
6
F05007-165
Bolt, 3/8-16 x 1” Carriage Grade 5
2
7
P322
Blade, 21” Gator Mulching
1
3
This mulching kit may be purchased through your Lastec Dealer. To properly use the mulching feature, the Deck 3 Baffle 049963 from the rear discharge kit must also be in place. The 049963 Deck 3 Baffle Includes the unit in a separate box as part of the Rear Discharge Baffle Assembly. All factory installed rear baffles remain in place for mulching.
5-14
Lastec//120315
61 in Deck
61 in Deck Optional Mulching Kit
5
LT0047C
61 in Deck
Lastec//120315
5-15
5 5.8 REF
Mower Decks Double Pulley Spindle (5/14 and later)
Double Pulley Spindle (5/14 and later) PART # 067695
1
DESCRIPTION Spindle Assembly, ZT 21” D6.3-6.3
COMMENTS
QTY.
Non-saleable item. Parts must be purchased separately.
1
1
P107 1
Fitting, 1/4-28 Straight Grease
1
2
0456771
Bolt, Spindle Single Pulley
3
F05011-97
Washer, 1/2” Plain Belleville
1
Maximum Torque: 57 ft-lbs
1
4
028080
Key, 1/4” Square x 1 1/2” Long
1
5
067688
Sheave, Double - Mower Deck
1
6
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
7
067696
Spindle Assembly, ZT Cast
8
F05010-222
Nut, 3/8-16 Flanged Hex Nyloc
4
9
P128
Blade, 21” x 2 1/2” x 1/4” High Lift
1
P246
Blade, 21” Low-Lift
Optional
1
P322
Blade, 21” Gator Mulching
Optional
1
Optional
1
063265
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
10
029889
Washer, 2 1/2” x 11/16” x 3/16” Nylon
11
F05011-89
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
12
F05009-95
13
048898
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 Blade Disc, Anti-Scalp
4 See Section 5.9 for parts
1
1 Remove to install Anti-Scalp Blade Disc
1
Torque Value: 75 ft-lbs
1
Optional part. Remove Item 11 to install Anti-Scalp Blade Disc
1
For service order 067354 Spindle Bolt 1 1/4” Service Kit including (1) P107 1/4-28 Straight Grease Fitting and (1) 045677 Spindle Single Pulley Bolt.
5-16
Lastec//042315
Mower Decks
Mower Decks Double Pulley Spindle (5/14 and later)
5
100_190
Mower Decks
Lastec//042315
5-17
5 5.9
Mower Decks Spindle Housing
Spindle Housing
REF
PART #
DESCRIPTION (Indicates Non-Saleable Items)
COMMENTS
067696
Spindle Assembly, Center w/Stiffener
Non-saleable item. Parts must be purchased separately.
QTY.
1
P11035
Bearing, 6206-2NSE
2
P105
O-Ring, 2 1/2” ID x 2 3/4” OD
4
3
072511
Spacer, Bearing Housing
1
4
067999
Spindle Housing, ZT- Common Core
1
5
067686
Spacer, Spindle Bearing Housing
1
6
034947
Washer, 1.50” x 1.185” x 16Ga
1
7
034948
Washer, 2.435” x 1.185” x 11Ga
1
8
067687
Shaft, Blade Spindle ZT Cast
1
1 3
Concerning Nachi Sealed Bearings: One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubricating the bearings forces the motor to work harder.
5-18
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure. Only a small of grease is required to lubricate a bearing in motion. When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements. When using open bearings, pack the bearing as follows:
Lastec//042315
Mower Decks
Mower Decks Spindle Housing
5
100_188
Mower Decks
Lastec//042315
5-19
5
61 in Deck Double Pulley Spindle (Prior to 5/14)
5.10 Double Pulley Spindle (Prior to 5/14) REF
PART # 049892
1
DESCRIPTION Spindle Assembly, 2861AGC Double Sheave
P04107
Fitting, 3/16” x 3/16” Straight Grease
COMMENTS Non-saleable item. Parts must be purchased separately.
QTY. 1 1
Maximum Torque: 57 ft-lbs
1
2
045677
Bolt, Spindle Single Pulley
3
F05011-97
Washer, 1/2” Plain Belleville
1
4
027053
Key, 1/4” x 2 1/2”
1
5
040049
Sheave, Double - 2561 Mower
1
6
046273
Washer, 1/4” x 1.47” x 1.01”
1
7
F05007-85
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
4
8
044862
Plate, Deck Reinforcing
Serial # 2940906 and later
2
048183
Plate, Deck Reinforcing
Serial # 2930806 and prior
1
See Section 5.11 for parts
9
043246
Spindle Assembly, Center w/Stiffener
10
F05010-10
Nut, 3/8-16 Hex Nyloc
11
P128
Blade, 21” x 2 1/2” x 1/4” High Lift
P246
Blade, 21” Low-Lift
Optional
1
P322
Blade, 21” Gator Mulching
Optional
1
063265
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Optional
1
12
029889
Washer, 2 1/2” x 11/16” x 3/16” Nylon
13
F05011-89
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
Serial # 2940906 and later. Remove to install Anti-Scalp Blade Disc
1
1 4 1
1
F05011-27
Washer, 5/8” Split Lock
Serial # 2930806 and prior
1
14
F05009-95
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Torque Value: 75 ft-lbs
1
15
048898
Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
5-20
Blade Disc, Anti-Scalp
Lastec//042315
61 in Deck
61 in Deck Double Pulley Spindle (Prior to 5/14)
5
LT0033
61 in Deck
Lastec//042315
5-21
5
61 in Deck Spindle Housing
5.11 Spindle Housing REF
PART # 043246
DESCRIPTION Spindle Assembly, Center w/Stiffener
COMMENTS
QTY
Non-saleable item. Parts must be purchased separately.
1
Added after serial # 33351208
3
1
F05006-140
Bolt, 5/16-18 x 5” Hex Head Grade 5
2
F05006-93
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5
3 deleted after serial # 33341208
3
3
F05011-13
Washer, 5/16” Split Lock
3 deleted after serial # 33341208
3
4
034921
Plate, Deck Reinforcing
1
5
034969
Seal, 2561 Spindle
1
6
034951
Collar, Spindle Top
7
062999
O-Ring, Spindle
8
P11035
Bearing, 6206-2NSE
3
9
034945
Housing, Spindle
1
10
F05012-64
Pin, 1/8” x 1/2” Roll
11
F05010-58
Nut, 5/16-18 Nylon Lock Hex
12
034950
Spacer, Spindle Bearing
1
13
F04254-45
O-Ring, 2 7/16" ID x 3/16" Diameter
2
14
034947
Washer, 1.50” x 1.185” x 16Ga
1
15
034948
Washer, 2.435” x 1.185” x 11Ga
1
16
043245
Shaft, Center Blade Spindle
1
1 Added after serial # 34990809
1
1 Added after serial # 33351208
3
Concerning Nachi Sealed Bearings: One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubricating the bearings forces the motor to work harder.
5-22
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure. Only a small of grease is required to lubricate a bearing in motion. When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements. When using open bearings, pack the bearing as follows:
Lastec//042315
61 in Deck
61 in Deck Spindle Housing
5
LT0024B
61 in Deck
Lastec//042315
5-23
5
61 in Deck Tensioner Assembly
5.12 Tensioner Assembly REF
PART # 049797
DESCRIPTION
COMMENTS
Idler Assembly, Deck Drive
QTY 1
1
F05010-222
Nut, 3/8-16 Flanged Hex Nyloc
1
2
F05010-1
Nut, 3/8-16 Hex
1
3
034982
Spring, 1 1/2” OD x 8 1/2” x .195”
1
4
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
1
5
029842
Bushing, 3/4” ID x 1” OD x 1” Oil
2
6
047878
Idler Pivot Weldment
1
7
F05008-10
Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5
1
8
P294
Fitting, 1/4-28 45 Deg Grease
1
045295
Pulley Assembly, 5” OD Idler, Flat
1
9
045297
Boss, Idler Pulley Standoff
1
10
F04254-12
Ring, 62mm IR Din #472 Retaining
2
11
P103
Bearing, Spindle Top 6305 RS
1
12
045296
Pulley, 5” OD Idler, Flat
Serial # 33151108 and later
1
043367
Pulley, 5” OD Idler
Serial # 33141108 and prior
1
13
062051
Washer, Water Shed Pulley
1
14
F05010-223
Nut, 1/2-13 Flanged Nylon Hex Lock
1
15
F05011-104
Washer, 3/8 x 1-1/2 x 1/8 Thick Hardened
1
5-24
Lastec//042315
61 in Deck
61 in Deck Tensioner Assembly
5
LT0029B
61 in Deck
Lastec//042315
5-25
5
61 in Deck Grass Chute
5.13 Grass Chute REF
PART # 041645
DESCRIPTION
COMMENTS
Grass Chute Assembly
QTY 1
1
F05010-58
Nut, 5/16-18 Nylok Hex
1
2
041714
Spring, Deere RH Torsion
1
3
041572
Grass Chute, John Deere
1
4
F05006-110
Bolt, 5/16-18 x 9” Hex Head Grade 5 Spcl
1
5-26
Lastec//042315
61 in Deck
61 in Deck Grass Chute
5
LT0044-2B
61 in Deck
Lastec//042315
5-27
5
61 in Deck Rear Anti-scalp Roller (Prior to 5/14)
5.14 Rear Anti-scalp Roller (Prior to 5/14) REF
PART # 049795
DESCRIPTION
COMMENTS
Wheel Assembly, Deck Anti-Scalp
QTY 1
1
F05010-10
Nut, 3/8-16 Hex Nyloc
2
2
063201 1
Plate, Anti-Scalp Adjusting
1
3
F05007-123
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
2
4
049794
Mount Weldment, Deck Anti-Scalp
1
5
F05010-185
Nut, 5/8-11 FlexLoc
1
6
F05010-82
Nut, 5/8-11 Jam
1
7
F05009-35
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
1
8
049870
Bushing, Urethane Pivot
1
9
F05010-96
Nut, 5/8-11 Jam Nylon Lock
1
10
027013
Wheel, Anti-Scalp, 5 5/8" hole
1
11
F05009-28
Bolt, 5/8-11 x 4” Hex Head Grade 5
1
1 Replaced
Deck Lift Link Rod Assembly (046700) on units with serial #34660609 and later. NOTE: 063201 is retrofittable to all units produced to date. 046700 does not work on units with serial #34660609 and later.
NOTE: Lubricate all surfaces of the inner bushing (049870) with a water-proof axle grease prior to assembly. CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
5-28
Lastec//042315
61 in Deck
61 in Deck Rear Anti-scalp Roller (Prior to 5/14)
5
LT0046
61 in Deck
Lastec//042315
5-29
6
SECTION 6 73” MOWER DECK
Lastec//042315
6-1
6 6.1 REF 1
6-2
73 in Deck Deck Framework
Deck Framework PART # 048272
DESCRIPTION
COMMENTS
Belt, 72" Deck Drive
QTY. 1
2
041645
Grass Chute Assembly
1
3
044632
Deck Weldment, 73 Articulating #3
1
4
044631
Deck Weldment, 73 Articulating #2
1
5
044630
Deck Weldment, 73 Articulating #1
1
Lastec//042315
73 in Deck
73 in Deck Deck Framework
6
LT0049
73 in Deck
Lastec//042315
6-3
6 6.2 REF
1
73 in Deck Deck 1 Hardware
Deck 1 Hardware PART #
DESCRIPTION
055390
Deck Assembly, 73” Articulating #1
COMMENTS
QTY. 1
1
F05009-35
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
1
2
F05010-185
Nut, 5/8-11 FlexLoc
2
3
044630
Deck Weldment, 73” Articulating #1
1
4
F05010-222
Nut, 3/8-16 Flanged Hex Nylock
3
5
055803
Cover, 61A Deck #1
1
6
F05009-20
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
1
7
067694 1
Spindle Assembly, ZT 25” D6.3-6.3
See Section 6.5 for parts
1
Replaced 055444 73” Double Sheave Spindle Assembly (See Section 6.7) to improve durability (8/14).
6-4
Lastec//042315
73 in Deck
73 in Deck Deck 1 Hardware
6
LT0050B
73 in Deck
Lastec//042315
6-5
6 6.3
73 in Deck Deck 2 Hardware
Deck 2 Hardware
REF
PART #
DESCRIPTION
1
044631
Deck Weldment, 73” Articulating #2 Gas
1
2
049870 1
Bushing, Urethane Pivot
6
048890
Plate Assembly, Deck Adjusting
3
055192
COMMENTS
QTY.
2
Bolt Weldment, Height Adjust Eye
1
4
F05010-29
Nut, 3/8-16 Jam
1
5
062950
Adjusting Weldment, Deck
1
6
P110
Pin, 3/8” x 1 5/16” Clevis, Yzn
2
7
P111
Ring, Kick-out, 1”
3
8
F04254-46
Ring, 3/4” External - External
1
9
F05011-77
Washer, 3/4” AN Yel/Cad
1
10
049894
Link, Front Deck Lift
2
11
P212
Pin, 3/8” x 2 1/8” Clevis, Yzn
1
12
F05010-223
Nut, 1/2-13 Flanged Hex Nylock
1
13
F05010-222
Nut, 3/8-16 Flanged Hex Nylock
3
048452
Pulley, 9” B-C Groove Idler
1
14
F04254-4
Ring, 1.575” ID 3000-156 Retaining
15
P06030-2
Bearing, 6203-2NSL 17mm SRI-2 ABEC-1
Available with Pulley Only
1
16
048451
Pulley Weldment, 9“ Idler
Available with Pulley Only
1
17
048453
Adapter, Idler Pulley Bore
Available with Pulley Only
1
18
055405
Spacer, 73” Deck 1/2ID x 1-3/8
19
F05008-61
Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5
1
20
F05010-10
Nut, 3/8-16 Hex Nylon Lock
2
21
F05007-165
Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5
2
22
055424
Baffle Weldment, 73” #2 Deck
1
23
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
1
24
F05010-1
Nut, 3/8-16 Hex
1
25
F05011-104
Washer, 3/8” x 1-1/2” x 1/8” Thick Hardened
1
26
027013
Wheel, Anti-Scalp 5-5/8" Hole
1
27
F05010-224
Nut, 5/8-11 Flanged Hex Nylock
1
28
072497
Spacer, 1 OD x .65 ID x .53 Long
1
29
F05009-10
Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5
30
072486
Spindle Assembly, 73” Gas Double Sheave
1 Lubricate
Available with Pulley Only
1
1
1 See Section 6.10
1
all mating surfaces of Urethane Pivot Bushing (049870) with a water-proof axle grease prior to assembly.
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
6-6
Lastec//042315
73 in Deck
73 in Deck Deck 2 Hardware
6
LT0032B
73 in Deck
Lastec//042315
6-7
6 6.4 REF
1
73 in Deck Deck 3 Hardware
Deck 3 Hardware PART #
DESCRIPTION
055392
Deck Assembly, 73” Articulating #3
COMMENTS
QTY. 1
1
F05010-222
Nut, 3/8-16 Flanged Hex Nylock
3
2
055804
Cover, 61A Deck #3
1
3
044632
Deck Weldment, 73” Articulating #3
1
4
F05009-20
Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5
1
5
F05010-185
Nut, 5/8-11 FlexLoc
2
6
F05009-35
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
1
055890
Baffle Assembly, #3 Deck Mulching 73”
1
7
F05007-85
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
1
8
F05010-222
Nut, 3/8-16 Flanged Hex Nylock
2
9
055891
Baffle Weldment, #3 Deck Mulching 73”
1
Bolt, 3/8-16 x 1” Carriage Grade 5
1
10
F05007-165
11
041645
Grass Chute Assembly
See Section 6.12 for parts
1
12
067694 1
Spindle Assembly, ZT 25” D6.3-6.3
See Section 6.5 for parts
1
Replaced 055444 73” Double Sheave Spindle Assembly (See Section 6.7) to improve durability (8/14).
6-8
Lastec//042315
73 in Deck
73 in Deck Deck 3 Hardware
6
LT0051B
73 in Deck
Lastec//042315
6-9
6 6.5 REF
Mower Decks Double Pulley Spindle, Decks 1 and 3 (8/14 and later)
Double Pulley Spindle, Decks 1 and 3 (8/14 and later) PART #
DESCRIPTION (Indicates Non-Saleable Items)
067694
Spindle Assembly, ZT 25” D6.3-6.3
1
P107
Fitting, 1/4-28 Straight Grease
COMMENTS
QTY.
Non-saleable item. Parts must be purchased separately.
1 1 1
2
045677
Bolt, Spindle Single Pulley
3
F05011-97
Washer, 1/2” Plain Belleville
Maximum Torque: 57 ft-lbs
1
4
028080
Key, 1/4” Square x 1 1/2” Long
1
5
067688
Sheave, Double - Mower Deck
1
6
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
7
067696
Spindle Assembly, ZT Cast
8
F05010-222
Nut, 3/8-16 Flanged Hex Nyloc
4
9
P701
Blade, 25” x 2 1/2” x 1/4” High Lift
1
P849
Blade, 25” x 2 1/2” x 1/4” Low Lift
Optional
1
P848
Blade, 25" Gator Mulching
Optional
1
Optional
1
4 See Section 6.6 for parts
1
063266
Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra
10
029889
Washer, 2 1/2” x 11/16” x 3/16” Nylon
11
F05011-89
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Remove to install Anti-Scalp Blade Disc
12
F05009-95
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Torque Value: 75 ft-lbs
1
13
048898
Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
6-10
Blade Disc, Anti-Scalp
Lastec//042315
1 1
Mower Decks
Mower Decks Double Pulley Spindle, Decks 1 and 3 (8/14 and later)
6
120_085
Mower Decks
Lastec//042315
6-11
6 6.6
Mower Decks Spindle Housing, Decks 1 and 3 (8/14 and later)
Spindle Housing, Decks 1 and 3 (8/14 and later)
REF
PART #
DESCRIPTION (Indicates Non-Saleable Items)
COMMENTS
067696
Spindle Assembly, Center w/Stiffener
Non-saleable item. Parts must be purchased separately.
QTY.
1
P11035
Bearing, 6206-2NSE
2
P105
O-Ring, 2 1/2” ID x 2 3/4” OD
4
3
072511
Spacer, Bearing Housing
1
4
067999
Spindle Housing, ZT- Common Core
1
5
067686
Spacer, Spindle Bearing Housing
1
6
034947
Washer, 1.50” x 1.185” x 16Ga
1
7
034948
Washer, 2.435” x 1.185” x 11Ga
1
8
067687
Shaft, Blade Spindle ZT Cast
1
1 3
Concerning Nachi Sealed Bearings: One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubricating the bearings forces the motor to work harder.
6-12
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure. Only a small of grease is required to lubricate a bearing in motion. When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements. When using open bearings, pack the bearing as follows:
Lastec//042315
Mower Decks
Mower Decks Spindle Housing, Decks 1 and 3 (8/14 and later)
6
100_188
Mower Decks
Lastec//042315
6-13
6 6.7 REF
73 in Deck Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14)
Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14) PART # 055444
1
DESCRIPTION
COMMENTS
Spindle Assembly, 73” Double Sheave
Non-saleable item. Parts must be purchased separately.
QTY. 1
1
P107 1
Fitting, 1/4-28 Straight Grease
1
2
045677
Bolt, Spindle Single Pulley
3
F05011-97
Washer, 1/2” Plain Belleville
1
4
027053
Key, 1/4” x 2-1/2”
1
5
040049
Sheave, Double - 2561 Mower
1
6
034947
Washer, 1.50” x 1.185 x 16Ga
1
7
043249
Washer, 3/8” x 1.5 x 1.01”
1
8
F05007-85
Bolt, 3/8-16 x 1 1/2” Carriage Gr5
4
9
044862
Plate, Deck Reinforcing
Serial # 2940906 and later
2
048183
Plate, Deck Reinforcing
Serial # 2930806 and prior
1
10
043246
Spindle Assembly, Center w/Stiffener
See Section 6.8 for parts
1
11
F05010-10
Nut, 3/8-16 Hex Nyloc
12
P701
Blade, 25” x 2 1/2” x 1/4” High Lift
P849
Blade, 25” x 2 1/2” x 1/4” Low Lift
Optional
1
P848
Blade, 25" Gator Mulching
Optional
1
063266
Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra
Optional
1
13
029889
Washer, 2-1/2” x 11/16” x 3/16” Nylon
14
F05011-89
Washer,2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Serial # 2940906 and later. Remove to install Anti-Scalp Blade Disc
1
Maximum Torque: 57 ft-lbs
1
4 1
1
F05011-27
Washer, 5/8” Split Lock
Serial # 2930806 and prior
1
15
F05009-95
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Torque Value: 75 ft-lbs
1
16
048898
Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
Blade Disc, Anti-Scalp
P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
6-14
Lastec//042315
73 in Deck
73 in Deck Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14)
6
LT0137
73 in Deck
Lastec//042315
6-15
6 6.8
73 in Deck Spindle Housing
Spindle Housing
REF
PART # 043246
DESCRIPTION Spindle Assembly, Center w/Stiffener
COMMENTS
QTY.
Non-saleable item. Parts must be purchased separately.
1
Added after serial # 33351208
3
1
F05006-140
Bolt, 5/16-18 x 5” Hex Head Grade 5
2
F05006-93
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5
3 deleted after serial # 33341208
3
3
F05011-13
Washer, 5/16” Split Lock
3 deleted after serial # 33341208
3
4
034921
Plate, Deck Reinforcing
1
5
034969
Seal, 2561 Spindle
1
6
034951
Collar, Spindle Top
7
062999
O-Ring, Spindle
8
P11035
Bearing, 6206-2NSE
3
9
034945
Housing, Spindle
1
10
F05012-64
Pin, 1/8” x 1/2” Roll
11
F05010-58
Nut, 5/16-18 Nylon Lock Hex
12
034950
Spacer, Spindle Bearing
1
13
F04254-45
O-Ring, 2 7/16" ID x 3/16" Diameter
2
14
034947
Washer, 1.50” x 1.185” x 16Ga
1
15
034948
Washer, 2.435” x 1.185” x 11Ga
1
16
043245
Shaft, Center Blade Spindle
1
1 Added after serial # 34990809
1
1 Added after serial # 33351208
3
Concerning Nachi Sealed Bearings: One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubricating the bearings forces the motor to work harder.
6-16
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure. Only a small of grease is required to lubricate a bearing in motion. When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements. When using open bearings, pack the bearing as follows:
Lastec//042315
73 in Deck
73 in Deck Spindle Housing
6
LT0024B
73 in Deck
Lastec//042315
6-17
6 6.9 REF
73 in Deck Tensioner Assembly
Tensioner Assembly PART # 055428
DESCRIPTION
COMMENTS
Idler Assembly, 73” Deck Drive
QTY. 1
1
F05010-223
Nut, 1/2-13 Flanged Hex Nylock
1
2
062051
Washer, Water Shed Pulley
1
045295
Pulley Assembly, 5” OD Idler, Flat
1
3
F04254-12
Ring, 62mm IR Din #472 Retaining
4
P103
Bearing, Spindle Top 6305 RS
5
045296
Pulley, 5” OD Idler, Flat
Serial # 33151108 and later
1
043367
Pulley, 5” OD Idler
Serial # 33141108 and prior
1
045297
Boss, Idler Pulley Standoff
1
6
2 1
7
055429
Idler Weldment, 73” Deck Drive
1
8
F05009-66
Bolt, 1/2-13 x 2 3/4” Hex Head Grade 8
1
9
029842
Bushing, 3/4” ID x 1” OD x 1” Oil
2
10
P294
Fitting, 1/4-28 45 Deg Grease
1
11
F05010-222
Nut, 3/8-16 Flanged Hex Nylock
1
12
F05011-104
Washer, 3/8” x 1 1/2” x 1/8” Thk Hardened
1
13
034982
Spring, 1 1/2” OD x 8 1/2” x .195”
1
14
F05010-1
Nut, 3/8-16 Hex
1
15
F05011-4
Washer, 3/8” Split Lock
1
16
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
1
17
019650
Spacer, 1/4” Thk Deck Height
2
6-18
Lastec//042315
73 in Deck
73 in Deck Tensioner Assembly
6
LT0031B
73 in Deck
Lastec//042315
6-19
6
73 in Deck Deck 2, Double Pulley Drive Spindle (8/14 and later)
6.10 Deck 2, Double Pulley Drive Spindle (8/14 and later) REF
PART # 072486
DESCRIPTION
COMMENTS
Spindle Assembly, 73” Gas Double Sheave
1
P107
Fitting, 1/4-28 Straight Grease
2
045677
Bolt, Spindle Single Pulley
QTY. 1 1
Maximum Torque: 57 ft.lbs
1
3
F05011-97
Washer, 1/2” Plain Belleville
1
4
028080
Key, 1/4” x 1-1/2”
1
5
072492
Sheave, 73 Double
1
6
F05007-78
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
4
7
067696
Spindle Assembly, ZT Cast
8
F05010-222
Nut, 3/8-16 Flanged Hex Nylon Lock
4
See Section 6.6 for parts
1
9
P107
Blade, 25” x 2-1/2” x 1/4” High Lift
1
10
029889
Washer, 2 1/2” x 11/16” x 3/16” Nylon
1
11
F05011-89
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Remove to install Anti-Scalp Blade Disc
1
12
F05009-95
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Torque Value: 75 ft.lbs
1
13
048898
Optional part. Remove Item 14 to install Anti-Scalp Blade Disc
1
6-20
Blade Disc, Anti-Scalp
Lastec//042315
73 in Deck
73 in Deck Deck 2, Double Pulley Drive Spindle (8/14 and later)
6
LT0149
73 in Deck
Lastec//042315
6-21
6
73 in Deck Deck 2, Double Pulley Drive Spindle (Prior to 8/14)
6.11 Deck 2, Double Pulley Drive Spindle (Prior to 8/14) REF
PART # 055427
DESCRIPTION
COMMENTS
Spindle Assembly, 73” Gas Double Sheave
QTY. 1
1
P107 1
Fitting, 1/4-28 Straight Grease
2
045677
Bolt, Spindle Single Pulley
3
F05011-97
Washer, 1/2” Plain Belleville
1
4
027053
Key, 1/4” x 2-1/2”
1
5
055395
Sheave, Double 73 Mower
1
6
034947
Washer, 1.50” x 1.185” x 16Ga
1
7
043249
Washer, 3/8” x 1.5” x 1.01”
1
8
F05007-85
Bolt, 3/8-16 x 1 1/2” Carriage Gr5
4
9
044862
Plate, Deck Reinforcing
2
10
043246
Spindle Assembly, Center w/Stiffener
11
F05010-10
Nut, 3/8-16 Hex Nylon Lock
4
12
P849
Blade, 25” x 2-1/2” x 1/4” Low Lift
1
13
029889
Washer, 2 1/2” x 11/16” x 3/16” Nylon
1
14
F05011-89
Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc
Remove to install Anti-Scalp Blade Disc
1
15
F05009-95
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Torque Value: 75 ft.lbs
1
16
048898
Optional part. Remove Item 14 to install Anti-Scalp Blade Disc
1
1 P107
6-22
Blade Disc, Anti-Scalp
1 Maximum Torque: 57 ft.lbs
See Section 6.8 for parts
1
1
replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
Lastec//042315
73 in Deck
73 in Deck Deck 2, Double Pulley Drive Spindle (Prior to 8/14)
6
LT0034
73 in Deck
Lastec//042315
6-23
6
73 in Deck Grass Chute
6.12 Grass Chute REF
PART # 041645
DESCRIPTION
COMMENTS
Grass Chute Assembly
QTY 1
1
F05010-58
Nut, 5/16-18 Nylok Hex
1
2
041714
Spring, Deere RH Torsion
1
3
041572
Grass Chute, John Deere
1
4
F05006-110
Bolt, 5/16-18 x 9” Hex Head Grade 5 Spcl
1
6-24
Lastec//042315
73 in Deck
73 in Deck Grass Chute
6
LT0044-2B
73 in Deck
Lastec//042315
6-25
6
73 in Deck Rear Anti-scalp Roller (Prior to 8/14)
6.13 Rear Anti-scalp Roller (Prior to 8/14) REF
PART # 049795
DESCRIPTION
COMMENTS
Wheel Assembly, Deck Anti-Scalp
QTY 1
1
F05010-10
Nut, 3/8-16 Hex Nyloc
2
2
063201 1
Plate, Anti-Scalp Adjusting
1
3
F05007-123
Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5
2
4
049794
Mount Weldment, Deck Anti-Scalp
1
5
F05010-185
Nut, 5/8-11 FlexLoc
1
6
F05010-82
Nut, 5/8-11 Jam
1
7
F05009-35
Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5
1
8
049870
Bushing, Urethane Pivot
1
9
F05010-96
Nut, 5/8-11 Jam Nylon Lock
1
10
027013
Wheel, Anti-Scalp, 5 5/8" hole
1
11
F05009-28
Bolt, 5/8-11 x 4” Hex Head Grade 5
1
1 Replaced
Deck Lift Link Rod Assembly (046700) on units with serial #34660609 and later. NOTE: 063201 is retrofittable to all units produced to date. 046700 does not work on units with serial #34660609 and later.
NOTE: Lubricate all surfaces of the inner bushing (049870) with a water-proof axle grease prior to assembly. CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
6-26
Lastec//042315
73 in Deck
73 in Deck Rear Anti-scalp Roller (Prior to 8/14)
6
LT0046
73 in Deck
Lastec//042315
6-27
7
SECTION 7 INDEX
Mower//042315
7-1
Part Number Index
014419, Decal, Hot Engine Warning 1-4, 1-6 014815, Rod End, 5/16-24 Male LH 2-32 014818, Spring, Extension 3/8” x 3” 2-2 014834, Bearing, w/Snap Ring 5/8” ID 2-32 015485, Fitting, 3/8 Barb Tee 3-2 016413, Box, Battery Modified 4-28 018734, Bushing, Kubota Rubber Mount 4-18 018739, Rod End, 3/8-24 Right Hand 2-32, 2-44 018740, Rod End 3/8-24 Left Hand 2-38, 2-40, 2-44 018751, Washer, Motor Mount 4-18 018773, Sheave, BK60 QT 3-4 018784, Decal, Diesel Refuel Caution 1-4, 1-6 019086, Knob, 1 3/8” x 3/8-24 2-36 019086, Knob, 1 3/8” x 3/8-24 2-26, 2-28 019359, Bushing, 15MM Split Taper 3-4 019552, Decal, Caution ‘Clean Radiatior’ 1-4, 1-6 019554, Decal, Warning, Operational Safety 425D 1-4, 1-6 019557, Decal, Lastec Logo Div WM 1-4, 1-6 019613, Plug, 1/2” Hole 2-24, 2-26, 2-28 019650, Spacer, 1/4” Thk Deck Height 6-18 019696, Cap, Hyd Tank (P631) 4-2 019696, Cap, Hydraulic Tank (P631) 4-4 024155, Clamp, 1/4" Wire 13/32” Mtg Hole 2-2 024155, Clamp, 1/4” Wire 13/32 Mtg Hole 2-46 024378, Switch, Key Diesel (Kubota) 2-24, 2-26, 2-28 026371, Spring, 1 3/8" x 15.8” x .187” Extension 2-44 026382, Angle, Battery Hold Down 4-28 026393, Fitting, #8 SAE / #8 JIC 90 X-L Elbow 3-4 026399, Spacer, Hydro Actuator 4-16 026402, Plug, Fuel Tank 4-4 026407, Plate Weldment, E-Brake Lock 2-42 026409, Pulley, E-Brake 2-42, 3-6, 3-8 026412, Rod Weldment, E-Brake Tensioner 2-42 026416, Cable E-Brake 2-42 026417, Hex Nut, 1-20 Slotted 3-6, 3-8 026439, Tire Assembly, 24” x 12-12 Turf Master 3-6, 3-8 026440, Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 3-6, 3-8 026443, Block, Spring Tensioner 2-44 026446, Rod Wldmnt, Spring Tensioner 2-44 026447, Turnbuckle, Deck Lift 2-44 026448, Turnbuckle Assembly, Deck Lift 2-44 027006, Spring, 1 1/8” x 7 1/2” x .091” Ext 4-12 027013, Wheel, Anti-Scalp 5-5/8" hole 2-18 027013, Wheel, Anti-Scalp 5-5/8" hole 6-6 027013, Wheel, Anti-Scalp, 5-5/8" hole 5-8, 5-28, 6-26 027015, Arm Weldment, 2561 Right Control 2-32 027016, Arm Weldment, 2561 Left Control 2-32
2
027053, Key, 1/4” x 2 1/2” 5-20 027053, Key, 1/4” x 2-1/2” 6-14, 6-22 027056, Plate, E-Brake Pulley Right 3-6 027057, Plate, E-brake Pulley Left 3-8 027066, Hose Assembly, 3/8” x 14-1/2” 3-14 028080, Key, 1/4” Square x 1 1/2” Long 5-16, 6-10 028080, Key, 1/4” x 1-1/2” 6-20 028217, Bushing, Rubber Radiator Mount 4-24 028352, Clamp,1” ID Coated 4-24 028390, Grip, Handle 2-32 028492, Plug, 3/8” NPT Hex Brass 3-14 028493, Fitting, 3/8” NPT F-M-F Tee 3-14 028507, Keys 2-24 028513, Gasket, Exhaust Kubota 4-26 028535, Oil, Shell TTF-SB 3-2 028593, Clamp, 3/4” EMT Coated 3-14 028601, Decal, Fwd/Rev Motion 1-4, 1-6 028603, Decal, Brake Control 1-4, 1-6 028818, Grommet, Fuel Tank Fitting 4-2, 4-4 028820 , Fitting, 1/4” Barb 90 Tank 4-2 028821, Filter, 1/4” Barb Tank Filter 4-2 029214, Spacer, 1.00” OD x .41” ID x 1/4” Thk Nylon-Blk 2-42 029354, Block, E-Brake Pivot 2-42 029360, Handle Weldment, E-Brake 2-42 029397, Rod Weldment, Brake Actuator 2-42 029436, Tank Assembly, Diesel Fuel 4-2 029436-1, Tank, 7 Gallon Molded Fuel 4-2 029559, Hose, Kubota Air Breather 4-14 029842, Bushing, 3/4” ID x 1” OD x 1” Oil 2-34, 3-16, 5-24, 6-18 029889, Washer, 2 1/2” x 11/16” x 3/16” Nylon 5-16, 5-20, 6-10, 6-20, 6-22 029889, Washer, 2-1/2” x 11/16” x 3/16” Nylon 6-14 034921, Plate, Deck Reinforcing 5-22, 6-16 034930, Plate Weldment, Deck Height Adjustment 2-38 034945, Housing, Spindle 5-22, 6-16 034947, Washer, 1.50 x 1.185 x 16Ga 6-16 034947, Washer, 1.50” x 1.185 x 16Ga 6-14 034947, Washer, 1.50” x 1.185” x 16Ga 5-18, 5-22, 6-12, 6-22 034948, Washer, 2.435 x 1.185 x 11Ga 6-16 034948, Washer, 2.435” x 1.185” x 11Ga 5-18, 5-22, 6-12 034950, Spacer, Spindle Bearing 5-22, 6-16 034951, Collar, Spindle Top 5-22, 6-16 034969, Seal, 2561 Spindle 5-22, 6-16 034982, Spring, 1 1/2” OD x 8 1/2” x .195” 5-24, 6-18 040049, Sheave, Double - 2561 Mower 5-20, 6-14
Lastec//042315
Index
Part Number Index
040102, Pin, Idler Pivot 3-16 040200, Clamp, 1 3/4” Worm 4-24 040256, Decal, Warning, Outer Decks -- German 1-6 040257, Decal, Warning, Outer Decks -- French 1-6 040258, Decal, Warning, Outer Decks -- Italian 1-6 040259, Decal, Warning, Outer Decks -- Spanish 1-6 040260, Decal, Warning, Outer Decks -- Danish 1-6 040267, Decal Kit, European Languages 1-6, 1-7 040272, Pump, 12cc Right Hydro 3-4 040273, Pump, 12cc Left Hydro 3-4 040311, Clutch, 5.75 Dia x 1 1/8 Bore 12V 4-10 040313, Clutch Assembly, 5.75 Pitch 1 1/8 Bore 12V 4-10 040314, Hose, Lower Radiator 4-24 040315, Hose, Upper Radiator 4-24 040321, Battery Assembly, 22HP Yanmar 4-28 040334, Guard Weldment, 22HP Clutch 4-12 040338, Weldment, Clutch Stop 4-10 040340, Capture Weldment, Clutch Stop 4-10 040345, Separator, Fuel/Water 4-16 040346, Bracket Weldment, Water Separator 4-16 040347, Plate Weldment, Cooler Mount 3-14 040351, Bracket, Top Radiator Mount 4-24 040354, Plenum Weldment, Upper Radiator 4-24 040356, Shield Weldment, Muffler 4-26 040360, Plate Weldment, Muffler Mount 4-26 040366, Mount Bracket, Muffler Heat Shield 4-26 040367, Radiator Assembly, 2261 4-24 040368, Plenum Weldment, Lower Radiator 4-24 040373, Shaft, 61AC Diesel Stub 4-10 040374, Guard Assembly, 22HP Yanmar 4-12 040376, Belt, AX-60 3-4 040378, Pump Assembly, 12cc Left Hydro 3-4 040379, Pump Assembly, 12cc Right Hydro 3-4 040382, Pulley, 5 in Crowned Idler 4-20 040384, Weather Strip, Belt Cover 4-12 040386, Hose, 3/8 Hyd x 25in Low Pressure 3-2 040386, Hose, 3/8” Hyd x 25" Low Pressure 3-12 040387, Bottle Assembly, 22HP Yanmar 4-24 040388, Hose, Fuel 1/4” x 32" 4-6 040389, Hose, Fuel 1/4” x 28" 4-6 040390, Guard Weldment, Right Radiator Screen 4-24 040391, Guard Weldment, Left Radiator Screen 4-24 040394, Weather Strip, Radiator Screen 4-24 040395, Idler Assembly, Comm. Diesel Hydro Drv 3-16 040396, Spacer Hydro Actuator 3-4 040630, Decal, Hydraulic TTF-SB Oil 3-2 040635, Black Cap, for 32oz Bottle Oil Container 3-2 040636, Bottle, 32oz Container for Oil 3-2
Index
040637, Spout Cap/ W Red Seal for 32oz Container 3-2 040642, Oil,TTF-SB 32oz Bottle Hydro 3-2 040910, Decal, Warning Operate From Seat 1-4, 1-6 040911, Decal, Warning Operate With Guards 1-4, 1-6 040912, Decal, Danger, Thrown Objects/Arrow 1-4, 1-6 041083, Valve, Two Tank Diverter 3-14, 4-6 041098-1, Tire, 24” x 12-12 (Tire Only) 3-6, 3-8 041180, Hose Assy, 26 OAL x 1/2 Hyd 3-2 041187, Cap, Fuel Tank w/Indicator 3 1/2” 4-2 041205, Decal, Thrown Objects CE Std 1-7 041206, Decal, Caution Symbol CE Std 1-7 041209, Decal, Keep Away/Rotating Drive Line CE 1-7 041572, Grass Chute, John Deere 5-26, 6-24 041645, Grass Chute Assembly 5-2, 5-12, 5-26, 6-2, 6-8, 6-24 041669, Socket, 12V Accessory Panel Mount 2-24, 2-26, 2-28 041714, Spring, Deere RH Torsion 5-26, 6-24 042003, Decal, Warning, Slope 1-4, 1-6 042922, Idler Wldmnt, Deck Drive 4-22 042925, Idler Assembly, Deck Drive 4-20, 4-22 042926, Boss Wldmt, Rubber Spring Tensioner 4-22 042928, Spring, Urethane 4-22 042931, Mount Weldment, Throttle Cable 4-10 042935, Radiator, 22HP Yanmar 4-24 042938, Exhaust Pipe, 22HP Yanmar 4-26 042940, Filter Assembly, 22HP Commercial 3-12 042941, Hose, 3/8 Hyd x 22in Low Press 3-2 042942 , Strap, Rubber Pad Mounting 2-50 042943, Plate, Mount Washer 2-50 042945 , Pad, Rubber Striping 2-50 042947, Striping Kit, Commercial Mower 2-50 042949 , Plate Weldment, Hanger Strap 2-50 042950, Bracket Wldmnt, Right Striping Kit 2-50 042951, Bracket Wldmnt, Left Striping Kit 2-50 042977, Plate, Radiator Mount 4-24 043225, Decal, Articulator Logo Div WM 1-4, 1-6 043245, Shaft, Center Blade Spindle 5-22, 6-16 043246, Spindle Assembly, Center w/Stiffener 5-20, 5-22, 6-14, 6-16, 6-22 043249, Washer, 3/8” x 1.5 x 1.01” 6-14 043249, Washer, 3/8” x 1.5” x 1.01” 6-22 043251, Bushing, Hex, 3/4” x 3/8” 3-14 043273, Bracket, Side Radiator Mount 4-24 043274, Plate, Air Breather Mount 4-14 043285, Spring, .72” x 2.75” x .105” MW 2-6 043285, Spring, 0.72” x 2.75” x 0.105” MW 2-8, 2-10 043320, Brake Assembly, 3377TZ Rear Drum 3-6, 3-8 043320, Brake Assembly, Rear Drum 3-10
Lastec//042315
3
Part Number Index
043320-1, Drum, 152.4mm w/Studs 3-6, 3-8, 3-10 043320-10, Spring, 152.4 x 25 Brake Return 3-10 043320-2, Brake, 152.4 x 25 Cam 3-6, 3-8, 3-10 043320-4, Stud, 1/2-20 x 1-1/4 Press In 3-10 043320-5, Arm, 152.4 x 25 Brake Actuator 3-10 043320-6, Clip, 152.4 x 25 Retainer 3-10 043320-7, Backing Plate, 152.4 x 25 Brake 3-10 043320-8, Cam, 152.4 x 25 Brake 3-10 043320-9, Shoe, 152.4 x 25 Brake 3-10 043367, Pulley, 5” OD Idler 5-24, 6-18 043441, Washer, Fuel Tank Retaining 4-2, 4-4 043442, Washer, Fuel Tank Double 4-2, 4-4 043448, Tubing, 1/4” x 17” Tygon 4-2 043459, Switch, DPST NO 5A Plunger 2-46 043543, Pulley, 5” OD V-Groove Idler 5-8 043950, Block, Drive Handle Mount 2-32 043952, Arm Pivot Weldment, Right Control 2-32 043956, Clamp, Blade Switch Mount 2-24, 2-26, 2-28 043968, Spacer, Wheel Yoke Bearing 2-20 044020, Cover, Handle Lockout Switch Right 2-46 044021, Cover, Handle Lockout Switch Left 2-46 044588, Switch, Blade Start/Stop 2-24, 2-26, 2-28 044630, Deck Weldment, 73 Articulating #1 6-2 044630, Deck Weldment, 73” Articulating #1 6-4 044631, Deck Weldment, 73 Articulating #2 6-2 044631, Deck Weldment, 73” Articulating #2 Gas 6-6 044632, Deck Weldment, 73 Articulating #3 6-2 044632, Deck Weldment, 73” Articulating #3 6-8 044641, Altenator, Yanmar, 3TVN70-ASA 4-8 044642, Gasket, Valve Cover, 3TNV70-ASA 4-8 044643, Gasket, Engine Set, Yanmar,3TNV70 4-8 044644, Seal, Front Main,Yanmar,3TNV70-ASA 4-8 044645, Filter, Fuel, 22HP Yanmar,3TNV-70 4-8 044646, Injector Assy, Yanmar, 3TNV70-ASA 4-8 044647, Filter, Oil, Yanmar, 3TNV70-ASA 4-8 044648, Switch, Oil Pressure, Yanmar, 3TNV70-ASA 4-8 044649, Seal, Rear Main, Yanmar, 3TNV70-ASA 4-8 044650, Motor, Starter, Yanmar, 3TNV70-ASA 4-8 044651, Thermostat, Yanmar, 3TNV70-ASA 4-8 044652, Thermostat Gasket, Yanmar TNV 4-8 044653, Pump, Water Assy, Yanmar, 3TNV70-ASA 4-8 044654, Gasket, Water Pump, Yanmar, 3TNV70-ASA 4-8 044655, Sender, Water Temp, Yanmar, TNV88/TNV70 4-8 044656, Solenoid, Fuel, Yanmar, TNV88/TNV70 4-8 044657, Diode, Solenoid Relay, Yanmar 3TNV88/70 4-8 044658, Timer, Yanmar, 3TNV70-ASA 4-8
4
044659, Gasket, Exhaust, Yanmar, 3TNV70-ASA 4-8 044660, Cap, Radiator 4-24 044661, Fan, Radiator, Yanmar, 3TNV70-ASA 4-8 044662, Gasket, Head, Yanmar, 3TNV70-ASA 4-8 044663, Plug, Oil Drain, Yanmar, 3TNV70-ASA 4-8 044664, Seal, Oil Drain, Yanmar, 3TNV70-ASA 4-8 044665, Plug, Glow, Yanmar, 3TNV70-ASA 4-8 044666, Gasket, Manifold, Yanmar, 3TNV70-ASA 4-8 044667, Dipstick, Yanmar, 3TNV70-ASA 4-8 044668, Fan Belt, Yanmar TNV 4-8 044669, Pipe, Fuel Return, Yanmar, 3TNV70-ASA 4-8 044671, Kit, Radiator, Yanmar, 3TNV70-ASA 4-8 044673, Water Separator, Screen, 3TNV70-ASA 4-16 044683, Hose, Clutch Stop Bushing 4-10 044712, Control Box Weldment, AC Diesel w/ Thrott 2-26 044715, Handle Weldment, Throttle 2-26, 2-28 044731, Decal, Control Box Engine Throttle 1-4, 1-6, 2-26 044862, Plate, Deck Reinforcing 5-20, 6-14, 6-22 045270, Pulley, 5 OD Idler 4-20, 4-22 045270, Pulley, 5” OD Idler, V Groove 5-8 045271, Pulley Assembly, 5” OD Idler, V Groove 5-8 045271, Pulley Assy, 5 in OD idler 4-20 045271, Pulley Assy, 5In OD Idler 4-22 045272, Boss, Idler Pulley Standoff 4-20, 4-22 045295 , Pulley Assembly, 5” OD Idler, Flat 5-24 045295, Pulley Assembly, 5” OD Idler Flat 3-16 045295, Pulley Assembly, 5” OD Idler, Flat 6-18 045296, Pulley, 5 OD Idler, Flat 3-16 045296, Pulley, 5” OD Idler, Flat 5-24, 6-18 045297, Boss, Idler Pulley Standoff 3-16, 5-8, 5-24, 6-18 045519, Decal, Sound Power Level 1-4, 1-6 045586, Hose, 1/4” x 41” Fuel 4-6 045677, Bolt, Spindle Single Pulley 5-16, 5-20, 6-10, 6-14, 6-20, 6-22 045897, Plate, Decal Fuel 4-2, 4-4 045967, Hose, Fuel 1/4” x 8-1/2” 4-6 045986, Wheel Assembly, 13” x 6.5” x 6” 2-20, 2-22 045988, Cable, Seat Lanyard 2-2 046129, Hour Meter, Digital LCD 2-24, 2-26, 2-28 046236, Handle Weldment, Throttle 2-36 046239, Washer, Throttle Friction 2-26, 2-28, 2-36 046240, Clamp, Throttle Conduit 2-36 046251, Washer Plate, Throttle Friction 2-26, 2-28, 2-36 046273, Washer, 1/4” x 1.47” x 1.01” 5-20 046293, Washer, Throttle Friction 2-26, 2-28, 2-36 046477, Wheel Yoke Assembly, 13” Comm 2-8, 2-10,
Lastec//042315
Index
Part Number Index
2-20, 2-46 046478, Yoke Weldment, 2561 Front Wheel 2-20 046487, Actuator Kit, 3386 RTN 3-4 046532, Tubing, 1/4” x 2" Long Tygon 4-2 046534, Mount, Spring 2-44 046551, Housing Cover, Kohler Filter 4-14 046552, Housing Cap, Kohler Filter 4-14 046553, Air Filter, Primary Element 4-14 046554, Air Filter, Inner Element 4-14 046555, Plug,Kohler Filter Minder 4-14 046556, Hood, Rain 4-14 046559, Switch, DPST N/O N/C 2-46 046659, Motor, Right Hydro-Gear Drive 3-6 046661, Motor, Hydro Gear 3-8 046750, Control Box Assembly 2-26 046751, Control Box Weldment 2-24 046800, Key, 5/16” x 1” Woodruff 3-6, 3-8 047187, Spacer, 5/8” x 1” x 5/8” 2-38 047234, Spring, .72 x 2.75 x .095 Dia SS Comp 2-38 047234, Spring, .72” x 2.75” x .095” Dia SS Comp 2-46 047234, Spring, .72” x 2.75” x .095” Dia. SS Comp 2-40 047519, Belt, B120 Drive 4-10 047523, Idler Assembly, Fixed Mule Drive 4-20 047526, Pivot Weldmnt, Mule Drv Tnsnr 4-22 047534, Screen Weldment, 33HP Radiator 4-24 047539, Tank Assembly, Diesel Dual Fittings 4-4 047581, Battery Assembly, 33Hp 4-28 047591 , Bracket, Fixed Idler Mount 4-20 047600, Kit, Hydro-Gear Flow est 3-2 047878, Idler Pivot Weldment 5-24 047881, Idler Weldment, Comm Diesel Hydro Drive 3-16 047883, Tube, Vinyl Sight Gage 3-14 048120, Weldment, Muffler 4-26 048166, Washer, Clutch Capture 4-10 048173, Washer, Wheel Damper 2-6, 2-8, 2-10 048174, Block, Wheel Yoke Friction 2-6, 2-8, 2-10 048183, Plate, Deck Reinforcing 5-20, 6-14 048187, Handle Weldment, Deck Raise 2-40 048227, Decal, Hydro Fill Line 1-4, 1-6 048272, Belt, 72" Deck Drive 6-2 048393, Mount, Extended Drive Handle 2-32 048400, Seal Kit, Hydro-Gear BDP 10-12 3-2 048451, Pulley Weldment, 9“ Idler 6-6 048452, Pulley, 9” B-C Groove Idler 6-6 048453, Adapter, Idler Pulley Bore 6-6 048468, Rod End, 7/16-20 x 3/8 High Misalign 2-38 048468, Rod End, 7/16-20 x 3/8” High Misalign 2-40 048499, Idler Adjust Weldment 3-16
Index
048504, Decal, Lastec, Roll Bar 1-4, 1-6 048532, Key, 5MM x 5MM x 25MM 3-4 048692, Strap, 1U 2-12, 2-14, 2-16, 2-38, 2-40, 2-44 048712, Bushing, 1 1/16" Urethane Pivot 2-12, 2-14, 2-16, 2-40, 2-44 048712, Bushing, 1-1/16" Urethane Pivot 2-38 048776, Hose, 3/8 Hyd x 14 Low Press. 3-2 048776, Hose, 3/8” Hyd x 14” Low Pressure 3-12 048890, Plate Assembly, Deck Adjusting 6-6 048898, Blade Disc, Anti-Scalp 5-16, 5-20, 6-10, 6-14, 6-20, 6-22 048904, Throttle Fitting, Swivel 2-30, 4-16 048953, Plate, Control Box Access 2-24, 2-26, 2-28 048965, Decal, Control Box 2-24, 2-26 048988, Fitting, 3/8” NPT - 3/8” Barb 45 Deg 3-12, 3-14 049212, Bracket, Filter Mount 3-12 049222, Cooler, Hyd Fluid 3-14 049227, Fitting, 1/2” NPT x 3/8” Hose Elbow 3-14 049255, Belt, B124 Wrapped 4-10 049273, Hose, 3/8 Hyd x 11in Low Press 3-2 049277, Bearing Half, Urethane Bushed 4-22 049300, Decal, Diesel Exhaust Warning 1-4, 1-6 049304, Decal, 33Hp Fuel Valve 1-4, 1-6 049306, Alarm, 3372 / 3386 2-24, 2-26, 2-28 049446, Washer, 1.50” OD x .53” ID UHMW 2-4 049447, Knob w/Stud, 3/8-16 x 1.50” 2-4 049448, Pull Pin, 1/2” 2-4 049459, Decal, 2273ADC Articulator Large 1-4, 1-6 049465, Decal, 73 In 1-4, 1-6 049466, Decal, Comm. Deck Height Adjustment 1-4, 1-6 049484, Bar Weldment, Pull 2-48 049488, Bar Assembly, Pull 2-48 049490, Deck Weldment, 61” Articulating #3 5-12 049490, Deck Wldmnt, 61 Articulating #3 5-2 049510, Bushing, Rubber Pivot 2-18, 5-8 049512, Deck Weldment, 61” Center 5-8 049512, Deck Wldmnt, 61 Center 5-2 049526, Deck Assembly, 61” Articulating #3 5-12 049532, Deck Weldment, 61 Articulatin #1 5-6 049532, Deck Wldmnt, 61 Articulatin #1 5-2 049537, Arm, E-Brake Link 2-42 049541, Rod Assembly, Rear Deck Lift 2-44 049542, Rod Wldmnt, Rear Deck Lift 2-44 049544, Rod Assembly, Front Deck Lift 2-40 049545, Rod Weldment, Front Deck Lift 2-38, 2-40 049550, Handle Assembly, E-Brake 2-42 049589, Pan Weldment, Seat 2-2 049590, Seat Assembly, Complete Gas 2-2
Lastec//042315
5
Part Number Index
049629, Decal Kit, 2261ADC 1-4 049638, Decal, Articulator 2261ADC 1-4, 1-6 049668, Wheel Yoke Assembly, 13” Comm Right 2-8, 2-10, 2-20 049706, Arm Assembly, Right Control Handle 2-32 049707, Arm Assembly, Left Control Handle 2-32 049710, Rocker Weldment, Left 2-6 049717, Rocker Weldment, Right 2-6 049720, Lift Weldment, Left Deck 2-16 049725, Lift Weldment, Deck Tab 2-12, 2-14, 2-16 049726, Lift Assembly, Left Rocker Deck 2-10, 2-16 049728, Pedal Assembly, Control 2-34 049730, Pedal Weldment, Foot Control 2-34 0497361, Frame Weldment, Comm. ROPS Lower 2-4 049736-11, Frame Weldment, Comm. ROPS Lower 2-4 049738, Rod Weldment, Foot Control 2-34 049739, Rod Assembly, Foot Control 2-34 049740, Rocker Wheel Assembly, Left 2-8, 2-10, 2-18 049741, Weldment, Left Rocker Wheel Pivot 2-18 049744, Weldment, Right Rocker Wheel Pivot 2-18 049745, Rocker Wheel Assembly, Right 2-8, 2-10, 2-18 049781, Baffle, Outside Rear Bolt-On 5-6, 5-12 049784, Baffle, Outside Rear Bolt-On 5-8 049787, Turnbuckle, Deck Lift Link 2-38, 2-40 049788, Rod Assembly, Deck Lift Link 2-40 049789, Lift Weldment, Right Deck 2-14 049790, Lift Assembly, Right Rocker Deck 2-8, 2-10, 2-14 049791, Cover, Left Rocker 2-6 049792, Cover, Right Rocker 2-6 049794, Mount Wldmnt, Deck Anti-Scalp 5-28, 6-26 049795, Wheel Assembly, Deck Anti-Scalp 5-28, 6-26 049796, ROPS Assembly, 2861 Folding 2-4 049797, Idler Assembly, Deck Drive 5-24 049831, Frame Weldment, ROPS 2-4 049843, Link Assembly, 3/8 Suspension 2-16 049843, Link Assembly, 3/8” Suspension 2-12, 2-14 049855, Belt, B-128 Deck Drive 5-2 049856, Cable Assembly, 2861 Throttle 2-36 049859, Hose, Fuel 1/4” x 12-1/2” 4-6 049866, Baffle Weldment, #1 Deck Mulching 5-14 049868, Spacer, .53” ID x 1 1/4” OD x 1 1/4” Lng 5-8 049870, Bushing, Urethane Pivot 2-18, 2-46, 5-8, 5-28, 6-6, 6-26 049873, Baffle Weldment, #3 Deck Mulching 5-10 049877, Baffle Weldment, #2 Deck Mulching 5-14 049891, Hose, 3/8” Low Pressure 28" 3-14 049892, Spindle Assembly, 2861AGC Double Sheave 5-20
6
049893, Washer, 3 1/2” OD Wave 2-6 049893, Washer, 3-1/2” OD Wave 2-8, 2-10 049894, Link, Front Deck Lift 5-8, 6-6 049928, Kit, Hydro Oil Repl 5 Gal 3372 3-2 049929, Kit, Hydro Oil Repl 2 1/2 Gal 3372 3-2 049930, Decal, Belt Routing 2861 1-4, 1-6 049931, Decal, 61 Inch Cut 1-4, 1-6 049951, Mount Assembly, 22HP Yanmar Engine 4-18 049952, Mount Weldment, 22HP Yanmar 4-18 049957, Mount Wldmt, 22HP Yanmar Engine 4-20 049960, Baffle Weldment, #2 Deck Rear Discharge 5-10 049961, Baffle Assembly, #2 Deck Rear Discharge 5-10 049962, Baffle Assembly, #2 Deck Mulching 5-14 049963, Baffle Assembly, #3 Deck Mulching 5-10 049964, Baffle Assembly, #1 Deck Mulching 5-14 049965, Wheel/Motor Assembly, 2861 Right Rear 3-6 049966, Wheel/Motor Assembly, 2861 Left Rear 3-8 049970, Tank Assembly, 22HP Hydraulic 3-14 049971, Tank Weldment, 2861AGC Hyd 3-14 049974, Engine, 22HP Yanmar Diesel 4-8 049984, Sure Grip, Foot Pan 2-46 049987, Tray Weldment, Battery Mount 4-28 049997, Baffle Kit, Rear Discharge 5-10 049998, Baffle Kit, Mulching 61AGC 5-14 049999, Bracket, Bottom Radiator Mount 4-24 050436, Relay, 40A 12VDC Automative 2-26 050436, Relay, 40A 12VDC Automotive 2-28 050477-1, Light Assembly, LED Red 3/16 FI Male Quicks 2-24 050477-1, Light Assembly, LED Red 3/16” FI Male Quicks 2-26, 2-28 052025, Seat Delay Assembly, LasTec Mowers 2-2 055083, Rocker Weldment, Left 2-8 055084, Rocker Weldment, Right 2-8 055085, Rocker Assembly, Left 2-8 055086, Rocker Assembly, Right 2-8 055151, Plate, E-Brake Cable Retaining 3-6, 3-8 055177, Plate, E-Brake Pulley Right 3-6 055178, Plate, E-brake Pulley Left 3-8 055192, Bolt Weldment, Height Adjust Eye 6-6 055382, Filter, Kohler Air Intake Fixed Mount 4-14 055384, Rocker Weldment, 73” Right 2-6 055384, Rocker Weldment, Right 2-10 055385, Rocker Weldment, 73” Left 2-6 055385, Rocker Weldment, Left 2-10 055386, Rocker Assembly, 73” Right 2-10 055387, Rocker Assembly, 73” Left 2-10 055390, Deck Assembly, 73” Articulating #1 6-4 055392, Deck Assembly, 73” Articulating #3 6-8
Lastec//042315
Index
Part Number Index
055395, Sheave, Double 73 Mower 6-22 055405, Spacer, 73” Deck 1/2ID x 1-3/8 6-6 055424, Baffle Weldmnt, 73” #2 Deck 6-6 055427, Spindle Assembly, 73” Gas Double Sheave 6-22 055428, Idler Assembly, 73” Deck Drive 6-18 055429, Idler Weldment, 73” Deck Drive 6-18 055442, Washer, 1/2” Delrin 2-44 055443, Cable Assembly, 2261 Throttle 2-30 055444, Spindle Assembly, 73” Double Sheave 6-14 055449, Decal Kit, 2273ADC 1-4, 1-6 055452, Kit, Rear Discharge Chute 5-10 055453, Separator Assembly, Water & Fuel 4-16 055464, Plate Weldment, Deck Height Adjust 2-40 055483, Lift Weldment, Left Deck 2-12 055486, Rocker Weldment, Left 2-8 055803, Cover, 61A Deck #1 5-4, 5-6, 6-4 055804, Cover, 61A Deck #3 5-12, 6-8 055831, Lift Assembly, Left Rocker Deck 2-8, 2-12 055834, Deck Assembly, 61” Articulating #1 5-4 055835, Deck Weldment, 61” Articulating #1 5-4 055835, Deck Weldmnt, 61 Articulating #1 5-2 055841, Sure Grip, 1 1/2” Bar 2-46 055890, Baffle Assembly, #3 Deck Mulching 73” 6-8 055891, Baffle Weldment, #3 Deck Mulching 73” 6-8 056241, Pedal Kit, AGC Foot 2-34 056449, Rod, Hydro Control Link 2-32 056450, Turnbuckle Assembly, Hydro Diesel 2-32 056585, Spring, Fuel Strainer, Yanmar 4-8 056586, O-Ring, Yanmar 4-8, 4-16 056587, Fuel Strainer, Yanmar 4-8 056589, Spring, Separator, Yanmar 4-16 056590, Float, Separator, Yanmar 4-16 056591, Decal, 18 PSI 1-4, 1-6 057559, Hood Assembly, 22HP Yanmar CE 1-8 059187, Bushing, Urathane Spring 3-16 061807, Hose Clamp, Dixon Worm Gear HSS6 3-2, 3-12 061952, Cable Assembly, Diesel Throttle 2-30 061953, Boot, Vinyl Cable 2-30 061954, Grommet, Cable Wiper 2-30 061974, Clamp, Cable 2-26, 2-28 062051, Washer, Water Shed Pulley 5-8, 5-24, 6-18 062404, Decal, AGC/ADC Hydro 1-4, 1-6 062425, Decal, Relays for 055700-055846 1-4, 1-6 062428, Decal, Relay 5 in Control Box 1-4, 1-6 062429, Decal, Lastec Made in USA 1-4, 1-6 062950, Adjusting Weldment, Deck 6-6 062999, O-Ring, Spindle 5-22, 6-16 063201, Plate, Anti-Scalp Adjusting 5-28, 6-26 063212, Cap, Deisel Starter Switch 2-26
Index
063212, Cap, Diesel Starter Switch 2-28 063218, Gauge, Temperature 0-250 Deg Electric 2-28 063219, Sender, Water Temperature 0-250 Deg 2-28 063220, Gauge, Tachometer 0-4000 RPM 16-Pole 2-28 063229, Control Box Assembly 2-28 063230, Control Box Weldment, Diesel w/ Throttle 2-28 063235, Decal, Control Box Diesel 1-4, 1-6, 2-28 063251, Cap, Diesel Fuel Tank Vented 4-4 063265, Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra 5-16, 5-20 063266, Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra 6-10, 6-14 064485, Wire Harness, 3300 Gauge Kit 2-28 064500, Nut Assembly, 3/8-16 Cover Retaining 1-8 064522, Kit, 2261/73 CE Hardware 1-8 064530, Decal Kit, 2261ADC-CE 1-6 064652, Fitting, Fuel 1/4 Bulkhead w/ Screen 4-4 067381, Battery, Group 26 w/Handle 4-28 067686, Spacer, Spindle Bearing Housing 5-18, 6-12 067687, Shaft, Blade Spindle ZT Cast 5-18, 6-12 067688, Sheave, Double - Mower Deck 5-16, 6-10 067694, Spindle Assembly, ZT 25” D6.3-6.3 6-4, 6-8, 6-10 067695, Spindle Assembly, ZT 21” D6.3-6.3 5-4, 5-8, 5-12, 5-16 067696, Spindle Assembly, Center w/Stiffener 5-18, 6-12 067696, Spindle Assembly, ZT Cast 5-16, 6-10, 6-20 067775, Jumper, Kubota Key Switch 2-28 067999, Spindle Housing, ZT- Common Core 5-18, 6-12 071864, Fitting, 8 ORFS - 10 STOR 90 3-6, 3-8 072486, Spindle Assembly, 73” Gas Double Sheave 6-20 072486, Spindle Assy, 73” Gas Double Sheave 6-6 072492, Sheave, 73 Double 6-20 072497, Spacer, 1 OD x .65 ID x .53 Long 5-8 072497, Spacer, 1 OD x .65 ID x .53 Long 6-6 072511, Spacer, Bearing Housing 5-18, 6-12 072827, Cover Assembly, Air Cleaner 4-14 072871, Fuel Pump, Yanmar Diesel 3TNV70 4-8 072872, Gasket, Fuel Pump Yanmar 3TNV70 4-8 073228, Gauge, Fuel Indicator Threaded Sealed 4-4 073229, Nut, Fuel Gauge 4-4 073230, Tank Assembly, 7 Gallon Diesel Dual Fitting 4-4 073357, Housing Cap Dirt Ejector, Kohler Filter 4-14 085614, Grommet, Rubber 2 1/2” Dia 4-2, 4-4
F F04203-3, Rivet, Self Sealing 4-2 F04203-6, Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop
Lastec//042315
7
Part Number Index
1-8 F04254-12, Ring, 62MM IR 4-20, 4-22 F04254-12, Ring, 62mm IR Din #472 Retaining 5-8, 5-24, 6-18 F04254-4, Ring, 1.575” ID 3000-156 Retaining 6-6 F04254-45, O-Ring, 2 7/16" ID x 3/16" Diameter 5-22 F04254-45, O-Ring, 2-7/16"ID x 3/16" Diameter 6-16 F04254-46, Ring, 3/4” External - External 2-34, 5-8, 6-6 F05004-1, Screw, 10-24 x 1/2” Sl Hex Machine 2-46, 3-14 F05004-123, Bolt, 3/8-16 x 3 1/2” Hex Head Gr5 2-38 F05004-123, Bolt, 3/8-16 x 3 1/2” Hex Head Grade 5 2-40 F05004-126, Screw, 10-24 x 3/4” Phillips PH Machine 2-46 F05004-18, Screw, 10-24 x 5/8 Unsl Indent HH Machine 4-2 F05004-18, Screw, 10-24 x 5/8” Unsl Indent HH Machine 4-4 F05004-230, Screw, M8-1.25 x 16 Hx Flange Serr 4-14 F05004-230, Screw, M8-1.25 x 16 Hx Flange Serr 4-10 F05004-232, Bolt, M12 x 1.25 x 40mm Hex Head 4-26 F05004-3, Screw, #10-24 x 3/8 Phillips PH Machine-> 2-24 F05004-35, Bolt, #10-24 x 1/2” Socket BH 4-12 F05004-40, Bolt, M8 x 1.25 x 1 C/S 8.8 Din 933 4-14 F05004-40, Bolt, M8 x 1.25 x 1 C/S 8.8 Din 933 HH 4-26 F05004-48, Bolt, M10-1.5 x 25mm Hex Head FT 8.8 Znc 4-18 F05004-93, Screw, 6-32 x 3/4 SBHC SS 2-24 F05004-93, Screw, 6-32 x 3/4” SBHC SS 2-26, 2-28 F05004-97, Screw, M10x1.5 x 35MM Hex Head 4-10 F05005-101, Bolt, 1/4-20 x 1” Hex Head Grade 5 3-4 F05005-105, Screw, 1/4-28 x 1/4” BO SH Cup Pt Set 2-32 F05005-105, Screw, 1/4-28 x 1/4” BO Socket Head Pt Set 2-12, 2-14, 2-16 F05005-123, Bolt, 1/4-20 x 3/4” Hex Head Grade 5 4-28 F05005-124, Bolt, 1/4-20 x 1 1/2” Hex Head Grade 5 4-28 F05005-137, Bolt, 1/4-20 x 5/8” Hex Head Grade 5 3-12, 4-24 F05005-137, Bolt, 1/4-20 x 5/8” Hex Head Grade 5 2-26, 2-28 F05005-78, Screw, 1/4-20 x 3/8” Hex Flanged Whiz Lock 4-24 F05005-78, Screw, 1/4-20 x 3/8” Hex Flanged Whiz Lock 3-14 F05005-79, Bolt, 1/4-20 x 1/2” Hex Head Cap 2-6
8
F05006-102, Bolt, 5/16-18 x 3/4” Hex Head 4-24 F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 2-2, 2-26, 2-28, 2-46 F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc 3-6, 3-8, 5-8 F05006-102, Bolt, 5/16-18x3/4 HH Gr5 Zinc 2-24 F05006-110, Bolt, 5/16-18x9 HH Gr5 Spcl 5-26, 6-24 F05006-117, Bolt, 5/16-18 x 3/4” SHC SS 3-6, 3-8 F05006-123, Bolt, 5/16-18 x 8-1/2” Hex Head Grade 5 4-28 F05006-140, Bolt, 5/16-18 x 5” Hex Head Grade 5 5-22, 6-16 F05006-27, Bolt, 5/16-18 x 1” Hex Head Grade 5 3-12 F05006-27, Bolt, 5/16-18 x 1” Hex Head Grade 5 2-2, 2-26, 2-28, 4-10, 4-16, 4-28, 5-6, 5-8, 5-12 F05006-3, Bolt, 5/16-18 x 3 1/2” Hex Head Full Thread 4-16 F05006-81, Bolt, 5/16-18 x 1 3/4” FT Hex Head Gr5 2-38 F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5 5-22 F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Grade 5 5-12 F05006-93, Bolt, 5/16-18x1 1/4 HH FT Gr5 6-16 F05007-109, Bolt, 3/8-16 x 4 3/4” Hex H ead Grade 5 2-44 F05007-109, Bolt, 3/8-16x4 3/4 HH Gr5 4-20 F05007-118, Bolt, 3/8-16 x 3/4” Hex Head Grade 5 4-24 F05007-118, Bolt, 3/8-16 x 3/4” Hex Head Grade 5 4-26 F05007-119, Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5 2-38, 2-40 F05007-123, Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 2-32, 3-6, 3-8 F05007-123, Bolt, 3/8-16x1 1/4 HH Gr5 5-28, 6-26 F05007-124, Bolt, 3/8-16 x 2” Hex Head Grade 5 3-8 F05007-125, Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5 2-12, 2-14, 2-16, 2-46 F05007-126, Bolt, 3/8-16 x 4” Hex Head Grade 5 2-4, 2-12, 2-14, 2-16, 2-38, 2-40 F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-36 F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-26, 2-28 F05007-129, Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5 4-12 F05007-136, Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5 2-38, 2-40, 2-44 F05007-156, Bolt, 7/16-20 x 1 1/2” Hex Head Grade 5 4-10 F05007-165, Bolt, 3/8-16 x 1” Carriage Grade 5 5-10,
Lastec//042315
Index
Part Number Index
5-14, 6-8 F05007-165, Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5 5-8, 6-6 F05007-206, Bolt, 3/8-16 x 2 3/4” Hex Head Grade 5 2-4 F05007-207, Bolt, 3/8-16X1 3/4 HH Gr8, Znc 4-22 F05007-208, Screw, 3/8-16 x 1-1/2” FHS 3-4 F05007-244, Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS 2-2 F05007-73, Bolt, 3/8-16 x 3” Hex Head Gr5 2-38 F05007-73, Bolt, 3/8-16 x 3” Hex Head Grade 5 2-40 F05007-78 , Bolt, 3/8-16x1 1/2 HH Gr5 2-50 F05007-78, Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 2-42, 2-44, 5-16, 5-24, 6-6, 6-10, 6-18, 6-20 F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Gr5 6-14, 6-22 F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 5-10, 5-20, 6-8 F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 3-14 F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 2-32, 4-26 F05008-10, Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 5-24 F05008-10, Bolt, 1/2-13x2 1/4 Hex Head GR5 4-20, 4-22 F05008-101, Bolt, 1/2-13 x 3/4” Hex Head Grade 5 4-24 F05008-102, Bolt, 1/2-13x2 HH Gr5 4-20 F05008-106, Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5 2-6 F05008-106, Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5 2-8, 2-10 F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 2-4, 2-8, 2-10, 3-16, 5-8 F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 Zinc 2-6 F05008-28, Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5 3-6, 3-8 F05008-35, Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5 2-8, 2-10 F05008-35, Bolt, 1/2-13 x 4-1/2” Hex Head Gr5 2-6 F05008-37 , Bolt, 1/2-13x1 1/4 HH Gr5 2-50 F05008-37, Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2-12, 2-14, 2-16 F05008-37, Bolt, 1/2-13x1 1/4 Hex Head GR5 Zinc 4-22 F05008-37, Bolt, 1/2-13x1-1/4 HH Gr5 Zinc 4-20 F05008-61, Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5 4-18 F05008-61, Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5 6-6 F05008-96, Bolt, 5/16-18 x 1 1/2” Hex Head Grade 5 2-32, 3-4 F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 2-6 F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 2-8, 2-10, 5-8
Index
F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 6-6 F05009-108, Bolt, 3/4-10 x 9” Hex Head Grade 5 2-20 F05009-20, Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 5-4, 5-6, 5-12, 6-4, 6-8 F05009-28, Bolt, 5/8-11x4 Gr5 HH 5-28, 6-26 F05009-35, Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5 2-48, 6-4, 6-8 F05009-35, Bolt, 5/8-11x2 3/4 HH Gr5 5-28, 6-26 F05009-37, Bolt, 5/8-11 x 3 Hex Head Grade 5 2-8, 2-10 F05009-37, Bolt, 5/8-11 X 3” Hex Head Grade 5 Zinc 2-6 F05009-66, Bolt, 1/2-13 x 2 3/4” Hex Head Grade 8 6-18 F05009-95, Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 5-16, 5-20, 6-10, 6-14, 6-20, 6-22 F05010-1, Nut, 3/8-16 Hex 2-32, 4-26, 5-24, 6-6, 6-18 F05010-10, Nut, #10-24 Hex Self-Locking 4-12 F05010-10, Nut, 3/8-16 Hex Nyl Lock 2-36, 4-20, 4-24 F05010-10, Nut, 3/8-16 Hex Nyl Lock 2-12, 2-14, 2-16 F05010-10, Nut, 3/8-16 Hex Nyloc 2-4, 2-12, 2-14, 2-16, 2-26, 2-28, 2-38, 2-40, 2-42, 2-44, 2-46, 3-4, 5-6, 5-12, 5-20, 5-28, 6-14, 6-26 F05010-10, Nut, 3/8-16 Hex Nylon Lock 6-6, 6-22 F05010-119, Nut, 5/16-24 Jam LH 2-30, 2-32 F05010-121, Nut, 5/16-18 Nylon Locking Jam 3-6, 3-8 F05010-123, Nut, 3/8-24 Free 2-32, 2-34 F05010-124, Nut, 3/8-16 Half Nyloc 2-32, 2-38, 2-40, 3-6, 3-8, 4-10 F05010-124, Nut, 3/8-16 Half Nylock 4-24 F05010-127, Nut, 1/2-13 Half Nylock, Znc 4-20, 4-22 F05010-127, Nut, 1/2-13 Half Nylon Lock 3-16 F05010-14, Nut, #10-24 Keps 2-46 F05010-14, Nut, #10-24 Keps-> 2-24 F05010-160, Nut, #10-24 Hex Self-Locking 4-12 F05010-160, Nut, 10-24 Hex Nylock-> 2-26, 2-28 F05010-162, Nut, M8 x 1.25 Free 4-14 F05010-162, Nut, M8x1.25 Free Zinc Plate 4-26 F05010-166, Nut, 3/8-24 LH Jam 2-38, 2-40, 2-44 F05010-17, Nut, 5/16-18 Hex 2-26, 2-28, 2-38 F05010-177, Nut, 3/4-10 Stover Swaged 2-20 F05010-185, Nut, 5/8-11 FlexLoc 2-8, 2-10, 5-4, 5-6, 5-12, 5-28, 6-4, 6-8, 6-26 F05010-185, Nut, 5/8-11 Flexloc 2-6 F05010-201, Nut, 1/2-13 Hi-Crown Acorn Cap Plated 2-8, 2-10 F05010-22, Nut, 3/8-24 UNF Hex Jam 2-44 F05010-222, Nut, 3/8-16 Flanged Hex Nyl Lock 5-10 F05010-222, Nut, 3/8-16 Flanged Hex Nyloc 5-4, 5-16, 5-24, 6-10
Lastec//042315
9
Part Number Index
F05010-222, Nut, 3/8-16 Flanged Hex Nylock 5-14, 6-4, 6-6, 6-8, 6-18 F05010-222, Nut, 3/8-16 Flanged Hex Nylon Lock 5-8, 6-20 F05010-223, Nut, 1/2-13 Flanged Hex Nylock 6-6, 6-18 F05010-223, Nut, 1/2-13 Flanged Nylon Hex Lock 5-24 F05010-224, Nut, 5/8-11 Flanged Hex Nylock 5-8 F05010-224, Nut, 5/8-11 Flanged Hex Nylock 6-6 F05010-234, Nut, 3/8-16 Hex Half Nylon Lock 316 SS 2-2 F05010-29, Nut, 3/8-16 Jam 6-6 F05010-34, Nut, 5/8-11 Nyl Lock 2-18 F05010-35, NUT, 1/2-13 FREE HEX, ZINC 4-22 F05010-38, Nut, 7/16-20 Jam 2-38, 2-40 F05010-44, Nut, #6-32 Hex 2-24 F05010-58, Nut, 5/16-18 Nyl Lock 3-12, 4-24 F05010-58, Nut, 5/16-18 Nylok Hex 2-2, 2-32, 3-4, 4-10, 4-16, 4-28, 5-6, 5-12, 5-26, 6-16, 6-24 F05010-58, Nut, 5/16-18 Nylon Lock Hex 2-46, 5-8, 5-22 F05010-59, Nut, #6-32 Keps 2-24, 2-26, 2-28 F05010-69, Nut, 1/4-20 Nylock 4-28 F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-6, 4-18, 4-20, 4-22 F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-6 F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-8, 2-10, 2-42, 3-6, 3-8 F05010-8, Nut, 1/2-13 Nylon Hex Lock 2-4, 2-8, 5-8 F05010-82, Nut, 5/8-11 Jam 5-28, 6-26 F05010-9, Nut, 1/4-20 Keps 4-28 F05010-96, Nut, 5/8-11 Jam Nyl Lock 5-28, 6-26 F05011-101, Washer, 1/2” SAE Flat Gr5-8 (Thru Hard) 2-44 F05011-101, Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard) 3-6, 3-8 F05011-104, Washer, 3/8 x 1-1/2 x 1/8 Thick Hardened 5-24 F05011-104, Washer, 3/8 x 1-1/2 x 1/8 Znc H 4-22 F05011-104, Washer, 3/8” x 1 1/2” x 1/8” Thk Hardened 6-18 F05011-104, Washer, 3/8” x 1-1/2” x 1/8” Thk Hardened 6-6 F05011-11, Washer, 1/4” SAE Flat 2-6, 4-24 F05011-11, Washer, 1/4” SAE Flat 4-28 F05011-110, Washer, 3/8” Push Nut 2-34 F05011-111, Washer, 20mm Bellville 2-34 F05011-115, Washer, 1” ID .03 SS Shim 3-6, 3-8 F05011-116, Washer, 1” ID .06 SS Shim 3-6, 3-8
10
F05011-13, Washer, 5/16 Split Lock 6-16 F05011-13, Washer, 5/16” Split Lock 4-16, 4-24 F05011-13, Washer, 5/16” Split Lock 2-24, 2-26, 2-28, 3-6, 3-8, 5-8, 5-22 F05011-14, Washer, 1/4” Split Lock 2-6, 3-12, 4-24 F05011-14, Washer, 1/4” Split Lock 2-26, 2-28, 3-4 F05011-16, Washer, 5/16” Standard Flat 3-6, 3-8 F05011-17, Washer, 5/16” SAE Flat 3-12, 4-24, 5-8, 5-12 F05011-17, Washer, 5/16” SAE Flat 2-24, 2-26, 2-28, 2-30, 2-46, 4-10, 4-16, 4-28, 5-6 F05011-18, Washer, #10 SAE Flat 3-14 F05011-2, Washer, 1/2 SAE Flat 4-22 F05011-2, Washer, 1/2” SAE Flat 2-12, 2-14, 2-16, 2-42, 3-16, 4-20 F05011-20, Washer, #10 Split Lock 2-24, 2-26, 2-28, 2-46, 4-2, 4-4 F05011-27, Washer, 5/8” Split Lock 5-20, 6-14 F05011-3, Washer, 3/8 Flat 4-20 F05011-3, Washer, 3/8” Flat SAE 2-4, 2-12, 2-14, 2-16, 2-32, 2-34, 2-38, 2-40, 2-44, 3-4, 3-6, 3-8, 4-10, 4-26, 5-6 F05011-3, Washer, 3/8” SAE Flat 2-36 F05011-33, Washer, 5/16” Star ET 4-10 F05011-4 , Washer, 3/8 Split Lock 2-50 F05011-4, Washer, 3/8 Split Lock 4-22 F05011-4, Washer, 3/8” Split Lock 3-14, 4-24 F05011-4, Washer, 3/8” Split Lock 2-32, 4-26, 6-18 F05011-40, Washer, 5/8” Standard Flat 2-48 F05011-45, Washer, 8mm Split Lock 4-14, 4-26 F05011-48, Washer, 7/16” Split Lock 4-10 F05011-5, Washer, 5/8” SAE Flat 2-6 F05011-5, Washer, 5/8” SAE Flat 2-8, 2-10, 2-18 F05011-50, Washer, 5/16” x 1 1/4” Fender 2-2 F05011-61, Washer, 3/8” SAE Flat 2-26, 2-28 F05011-62, Washer, 3/4” SAE Flat 2-20, 3-16 F05011-68, WASHER, 1/2 STANDARD FLAT 4-22 F05011-68, Washer, 1/2 Standard Flat 4-20 F05011-77, Washer, 3/4” AN 3-16 F05011-77, Washer, 3/4” AN Yel/Cad 2-34, 5-8, 6-6 F05011-88, Washer, 10mm Split Lock 4-18 F05011-88, Washer, 10mm Split Lock 4-10 F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat 5-20 F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc 5-16, 6-10, 6-20, 6-22 F05011-89, Washer,2 1/2” OD x 5/8” ID x 3/16” Std Flat
Lastec//042315
Index
Part Number Index
Znc 6-14 F05011-9 , Washer, 1/2 Split Lock 2-50 F05011-9, Washer, 1/2” Split Lock 4-24, 5-8 F05011-97, Washer, 1/2” Plain Belleville 2-42, 5-16, 5-20, 6-10, 6-14, 6-20, 6-22 F05012-1, Pin, 1/8” x 1” Cotter 2-42 F05012-11, Pin, 3/16” x 1” Roll 2-42 F05012-115, Pin, 3/4 In Clevis Retaining 4-22 F05012-115, Pin, 3/4” Clevis Retaining 2-42, 3-16 F05012-3, Pin, 1/8” x 3/4” Cotter 2-34 F05012-49, Pin, 1/8” x 1 1/2” Cotter 2-20, 3-6, 3-8 F05012-64, Pin, 1/8” x 1/2” Roll 5-22 F05012-64, Pin, 1/8x1/2 Roll 6-16 F05012-79, Pin, 5/32” x 1 1/2” Cotter 2-20 F05012-8, Pin, 3/8” x 1 3/32” Clevis 2-44 F05015-17, Bolt, #10-24 x 1/2” PH 2-36 F05015-17, Bolt, #10-24 x 1/2” Ph Pan Head, Type 23 2-26, 2-28 F0510-185, Nut, 5/8-11 FlexLoc 2-48 F05254-12, Ring, 62mm IR Din #472 Retaining 3-16 F412, Screw, Seat Switch 2-2
I IS-0192 , Instr. Sheet, 61 Deck Striping Kit 2-50 IS-0218, Instruction Sheet, 056241 Kit 2-34 IS-0308, Instruction Sheet, 2261/73 CE Hardware Kit 1-8
N N/A, Bolt, 3/8-16 x 7” Hex Head Grade 5 2-12, 2-14, 2-16 N/A, Bushing, 3/8” Polyurethane Suspension 2-12, 2-14, 2-16 N/A, Spacer, 3/8” Suspension 2-12, 2-14, 2-16 N/A, Washer, 3/8” Suspension 2-12, 2-14, 2-16
P P04107, Fitting, 3/16” x 3/16” Straight Grease 5-20 P04211, Knob, 5/8-18 Ball 2-38, 2-40, 2-42 P04332, Cap, 3/8” Pipe Galvanize 3-14 P04646, Nut, 1/2-20 Lug 3-6, 3-8 P05035, Collar, 5/8” ID Lock 2-32 P06030-2, Bearing, 6203-2NSL 17mm SRI-2 ABEC-1 6-6 P06104, Foot, Rubber 4-12 P07584, Clamp, 1/2” EMT Coated 4-24 P09895, Clamp, Worm, 2 1/2” 4-14 P103, Bearing, Spindle Top 6305 RS 3-16, 4-20, 4-22, 5-8, 5-24, 6-18 P105, O-Ring, 2 1/2” ID x 2 3/4” OD 5-18, 6-12 P107, Blade, 25” x 2-1/2” x 1/4” High Lift 6-20 P107, FITTING, 1/4-28 STRAIGHT GREASE 4-22
Index
P107, Fitting, 1/4-28 Straight Grease 2-6 P107, Fitting, 1/4-28 Straight Grease 2-8, 2-10, 2-34, 2-46, 3-16, 5-16, 6-10, 6-14, 6-20, 6-22 P110, Pin, 3/8” x 1 5/16” Clevis 2-34, 2-42, 2-44 P110, Pin, 3/8” x 1 5/16” Clevis, Yzn 5-8, 6-6 P11035, Bearing, 6206-2NSE 5-18, 5-22, 6-12, 6-16 P111, Ring, 1” Kick-Out 2-40, 2-44 P111, Ring, Kick-out, 1” 2-38, 5-8, 6-6 P11258, Strap, 24” Rubber With Hooks 4-28 P117, Decal, Hands & Feet 1-6 P12161, Washer, Felt Battery Terminal 4-28 P12708, Fitting, 3/8” NPT-3/8” Barb Elbow 3-14 P12708, Fitting, 3/8NPT-3/8 Barb Elbow 3-12 P12722, Fitting, #6 90Deg SAE #6 Hose Barb Hyd. 3-4 P12724, Fitting, 3/8” NPT-3/8” Barb 3-14 P128, Blade, 21” x 2 1/2” x 1/4” High Lift 5-16, 5-20 P190, Bearing, 1” ID Tapered Roller 2-20 P191, Seal, 1 1/4” ID Trb Bearing 2-8, 2-10 P195, Cap, Hub 2-8, 2-10, 2-46 P212, Pin, 3/8” x 2 1/8” Clevis 2-40 P212, Pin, 3/8” x 2 1/8” Clevis, Yzn 2-38, 5-8, 6-6 P246, Blade, 21” Low-Lift 5-16, 5-20 P292, Bearing, Tapered Roller, 3/4” ID 2-22 P293, Seal, TRB, 3/4” ID 2-22 P294, Fitting, 1/4-28 45 Deg Grease 5-24, 6-18 P296, Spacer, 1.13” OD x .75” ID x .5” 2-20 P322, Blade, 21” Gator Mulching 5-14, 5-16, 5-20 P402, Bearing Race Insert, 3/4" TRB 2-22 P434, Nut, 3/4-16 Castle 2-20 P478, Decal, Danger - Rotating Blades 1-4, 1-6 P611, Holder, Jumbo Cup Black 2-46 P619, Filter Head, 3/8” NPT 3-12 P620, Filter Element, Spin On, BE-25-25 Zinga 3-2 P620, Filter, Spin On 25 Micron 3-12 P629, Grip, Foot Control Black 2-34 P630, Seat, Air Ride (Color Gray) 2-2 P649, Hose Clamp, 7/32”-5/8” 3-14 P649, Hose Clamp, 7/32”-5/8” 4-6 P686, Yoke, 3/8In-24 2-34 P701, Blade, 25” x 2 1/2” x 1/4” High Lift 6-10, 6-14 P776, Seat Belt, 2” ALR/ERI Buckle 2-2 P786, Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged 2-42 P786, Bushing,3/4IDx1 ODx5/8 Lng Flgd 4-22 P826, Switch, Seat 2-2 P829, Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2-12, 2-14, 2-16 P848, Blade, 25" Gator Mulching 6-10, 6-14 P849, Blade, 25” x 2 1/2” x 1/4” Low Lift 6-10, 6-14
Lastec//042315
11
Part Number Index
P849, Blade, 25” x 2-1/2” x 1/4” Low Lift 6-22
S12284, Tube, 7/8” Dia. Elec Motor Spacer 2-40
S
T
S12284, Tube, 7/8 Dia Elec Motor Spacer 4-10 S12284, Tube, 7/8” Dia Elec Motor Spacer 2-38
T215, Spacer, 3/4 OD x 25/64 ID x 3/4 Lng 4-22
12
Lastec//042315
Index