Performance Checklist ASTM C-39 Standard Test Method for ...
Recommend Documents
Dec 15, 2016 - C114 Test Methods for Chemical Analysis of Hydraulic ... instrumental techniques. 5. ... 2 Section on Safety, Manual of Cement Testing, Annual Book of ... *A Summary of Changes section appears at the end of this standard.
This standard is issued under the fixed designation C 39'(' 30M; the number
immediately ... 'Tlus test method is under the jurisdiction of ASTM Committee ('0')
on.
Condensation. Exposures of Paint and. Related Coatings. 91-2.02. Paint. 1
validation test per batch. ASTM A123. A123M A653. A653M A123. A123M A53
A53M.
'ASTM D638-Standard Test. Method for Tensile Properties of Plastics' can be
adapted to the testing of TSLs after some modifications. This test standard was.
ASTM C423-02. STC Test Standard: ASTM E90-02. Product Series Tested: Stride
Acoustical Panel – Acoustic Insert Installed. Test Completion Date: August 8 ...
Jan 28, 2014 ... ASTM C-1231 Standard Practice for Use of Unbonded Caps in Determination of
Compressive Strength of. Hardened Concrete Cylinders. P.
Jan 9, 2012 ... The observations and test results in this report are relevant only to the sample
tested. This report by itself does not imply that the material ...
Filling Slump Cone. Slump cones are for testing grout consistency prior to
grouting. Hold cone firmly in position so grout does not escape while filling the
cone.
CFR Section(s):. Standards Body: e. ASTM D1303: Standard Method of Test for Total. Chlorine in Vinyl Chloride Polymers and Copolymers. 21 CFR 177.1610(a).
Standard Methods of Chemical Analysis of Portland Cement, ASTM C114-44 ...... The section at the top should be filled out for company and individual returning ...
2.1 ASTM Standards: D 129 Test Method for Sulfur in Petroleum Products. (
General Bomb Method). D 516 Test Method for Sulfate Ion in Water. D 808 Test ...
ASTM, "E8 Standard Test Methods of Tension Testing of Metallic Materials,"
Annual. Book or ASTM Standards, American Society for Testing and Materials,
Vol.
Department of Crop and Soil Sciences, College of. Agriculture and Life Sciences, Cornell University. Daniel, D.E., 1982. Measurement of hydraulic conductivity ...
static air pressure. The air pressure is intended to simulate actual natural weather characteristics such as normal and
Organization, Per Suherman, Arie van Riessen, Brian O'Connor, Deyu Li, Dick Bolton, and. Hans Fairhurst of Curtin University of Technology were also used in ...
tractor unit and trailer being presented for the test. .... Vehicles are fitted with a
number of warning lights ... relation to your motorcycle engine size and power.
cases of dense or cemented sandy soils, however, N > ... along the entire penetration depth in sandy soils. ... recognized (Randolph, 2003; Jardine et al. 2005 ...
This standard test method is intended for use by VCI material manufacturers and ...... The temperature of the water bath shall be within the stated range limits for ...
bitumen emulsion bond strength development over time, as well as binder-aggregate ...... road as a structurally sound surface that has a durable, waterproof, ...
CRI Technical Bulletin: CRI Test Method 116 (07/10). CRI Test ... Standard
Laboratory Practice for Consumer Applied Pet Stain and Odor Removal.
Chemical ...
1.1 This test method covers determination of slump of concrete, both in the ... the
frustum of a cone with the base 8 in (200 mm) in diameter, the top 4 in (100 mm).
2.1 ASTM Standards: D95 Test Method for Water in Petroleum Products and ... 1
This test method is under the jurisdiction of ASTM Committee D-2 on. Petroleum ...
A, and Appendix X3 for details. 1.4 This test method includes the following:
Change in Mass (after immersion). Section 10. Change in Volume (after
immersion).
Dec 1, 1992 - yokes, each rigidly attached to the specimen. Support rods shall be used to maintain a constant distance be- tween the two yokes until testing is ...
Performance Checklist ASTM C-39 Standard Test Method for ...
Revised: January 30, 2013. R. Rincon. Performance Checklist. ASTM C-39
Standard Test Method for Compressive Strength of. Cylindrical Concrete
Specimens.
Revised: September 2, 2014 C. Roberts
Procedure Checklist ASTM C-39 Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens P Item 1.
Remove specimen from moist storage, but keep moist.
2.
Check specimen for perpendicularity (less than 0.5 ) to the axis and planeness (0.002”) of ends
3.
Determine diameter to nearest 0.01 inch by averaging two diameters measured at right angles to each other at about mid-height of the specimen.
4.
Wipe clean the bearing faces of the upper and lower bearing blocks and of the test specimen.
5.
Place test specimen on lower bearing block.
6.
Align the axis of the specimen with the center of thrust of the top (spherically seated) block.
7.
Verify that the load indicator is set to zero.
o
8.
Prior to applying the load on the specimen, tilt the movable portion of the spherically seated block gently by hand so that the bearing face appears to be parallel to the top of the test specimen. When Using Unbonded Caps perform steps 9 and 10. 9.
Verify the alignment of the specimen after application of load, but before reaching 10% of the anticipated specimen strength.
10.
Check to see that the axis of the cylinder does not depart from vertical by more than o 0.5 and the ends of the cylinder are centered within the retaining rings.
11.
Apply load continuously and without shock, at a rate of movement corresponding to a stress rate of 35 ± 7 psi/sec, during the latter half of the anticipated loading phase.
12.
Make no adjustment in the rate of movement as the ultimate load is being approached and the stress rate decreases due to cracking.
13.
Apply the load until complete failure occurs and the specimen displays a well-defined fracture pattern.
14.
Record maximum load.
15.
Note the type of fracture pattern.
16.
Calculate the compressive strength and report with required precision according to ASTM C39. Remark: Compressive Strength = ± 10% of calculated PSI of IA results
