PRODUCT CATALOG. 2012 www.aaatech.com. TOTAL SOLUTION SERVICE.
For the Industrial Piping Marketplace. 4 1 Y E A R S S E R V I N G I N D U S T R Y
...
AAA TECHNOLOGY
& SPECIALTIES CO., INC.
PRODUCT CATALOG
2017—Feb. 2 www.aaatech.com
P R O U D L Y
S E R V I N G
I N D U S T R Y
S I N C E
1 9 7 1
AAA Technology & Specialties Co., Inc.
TABLE OF CONTENTS Introduction
1
Shoe Types
2-3
How to Order—Pipe Shoe Variables
4
Pipe Shoe Variables—Slot Option Details
5
Selecting the Best Pipe Shoe—Selection Logic
6
Selection Logic—Guide Details
7
Slide Bearing Option Details
8
Base Plate Details
9
How To Order with Custom Properties
10
SHOE TYPES AND SPECIFICATIONS
Fig 5000 - Split Beam T-Shoe
11
Fig 5001 - Split Beam T-Shoe with Gussets
12
Fig 5010 - Split Beam T-Shoe with U-Bolts
13
Fig 5011 - Split Beam T-Shoe with U-Bolts and Gussets
14
Fig 5020 - Split Beam T-Shoe with Clamps
15
Fig 5021 - Split Beam T-Shoe with Clamps and Gussets
16
Fig 5100 - Fabricated T-Shoe
17
Fig 5101 - Fabricated T-Shoe with Gussets
18
Fig 5110 - Fabricated T-Shoe with U-Bolts
19
Fig 5111 - Fabricated T-Shoe with U-Bolts and Gussets
20
Fig 5120 - Fabricated T-Shoe with Clamps
21
Fig 5121 - Fabricated T-Shoe with Clamps and Gussets
22
Fig 5200 - Double Upright T-Shoe
23
Fig 5201 - Double Upright T-Shoe with Gussets
24
Fig 5210 - Double Upright T-Shoe with U-Bolts
25
Fig 5211 - Double Upright T-Shoe with U-Bolts with Gussets
26
Fig 5220 - Double Upright T-Shoe with Clamps
27
Fig 5221 - Double Upright T-Shoe with Clamps with Gussets
28
Fig 5500 - Heavy Duty Pipe Saddle
29
Page 1
PIPE SHOES
Pipe Shoes and Saddles AAA Technology & Specialties Co., Inc. is proud to provide a complete line of Pipe Shoes and Supports. These pipe shoes are constructed in accordance with the rules and regulations specified and defined by the Quality Assurance Procedures for Pipe Supports Manufactured per the ASME B31.1, B31.2, B31.3, B31.4, B31.5, B31.8, B31.9, B31.11 & B31.12 Piping Codes, the ANSI/AWS D1.1 and the MSS SP-58 & MSS SP-69 Standards. Well trained and experienced personal using formal standardized document systems and fabrication control methods supervise all projects. The Pipe Shoes and Supports offered herein are built in three categories: Split Beam Construction, Welded Flat Bar or Cut/Burned Plate or Double Upright Construction in accordance to your requirements. In addition, we can supply these in various Guided Shoe Assemblies as illustrated in the following pages.
These shoes can also be constructed with our TRI*SLIDE™ low friction slide bearings in one of the following combinations: 1. PTFE upper & lower bearings, 2. Stainless Steel upper & PTFE lower bearings, 3. Stainless Steel upper & Graphite lower bearing, 4. Graphite upper & Graphite lower bearing or any other combination that you require. We are also able to supply Stainless Steel upper & lower Meehanite slide bearings with Alloy Steel or Stainless Steel construction for high temperature applications, Polyurethane Saddles, Permali or Composite Supports for cryogenic applications, and can fabricate these out of machined block or poured to your specific needs. Please do not hesitate to call or e-mail AAA Technology & Specialties Co., Inc. to tell us about your requirements so that we can better serve you and fulfill your Pipe Support needs.
Page 2
AAA Technology & Specialties Co., Inc.
PIPE SHOES SHOE TYPES Choose from three designs of unreinforced pipe shoes: 1) Split Beam T-Shoe (single upright); 2) Fabricated (from flat bar or cut plate) Pipe Shoe (single upright); or 3) Double Upright Pipe Shoe. Each design, in turn, can be fabricated : 1) Plain; 2) With UBolts; or 3) With Pipe Clamps.
Fig. 5000, 5010, & 5020 SPLIT BEAM T-SHOES
5000 - Split Beam
5010 - Split Beam with U-Bolts
5020 - Split Beam with Clamps
Fig. 5100, 5110, 5120 FABRICATED T-SHOES
5100 - Fabricated
5110 - Fabricated with U-Bolts
5120 - Fabricated with Clamps
Fig. 5200, 5210, & 5220 DOUBLE UPRIGHT T-SHOES
5200 - Double Upright
5210 - Double Upright with U-Bolts
5220 - Double Upright with Clamps
Page 3
PIPE SHOES SHOE TYPES Choose from three designs of gusseted or reinforced pipe shoes: 1) Split Beam T-Shoe (single upright); 2) Fabricated (from flat bar or cut plate) Pipe Shoe (single upright); or 3) Double Upright Pipe Shoe. Each design, in turn, can be fabricated : 1) Plain; 2) With U-Bolts; or 3) With Pipe Clamps.
Fig. 5001, 5011, & 5021 SPLIT BEAM T-SHOES
5001 - Split Beam- Gussets
5011 - Split Beam with U-Bolts - Gussets
5021 - Split Beam with Clamps - Gussets
Fig. 5101, 5111, 5121 FABRICATED T-SHOES
5101 - Fabricated- Gussets
5111 - Fabricated with U-Bolts—Gussets
5121 - Fabricated with Clamps—Gussets
Fig. 5201, 5211, & 5221 DOUBLE UPRIGHT T-SHOES
5201 - Double Upright - Gussets
5211 - Double Upright w/ U-Bolts—Gussets
5221 - Double Upright w/ Clamps—Gussets
AAA Technology & Specialties Co., Inc. AAA Technology & Specialties Co., Inc.
Page 4
PIPE SHOES HOW TO ORDER Standard Pipe Shoes are ordered by indicating the following dimensions and choices:
Fig.
Description of Pipe Shoe
Fig.
Description of Pipe Shoe W/ Gussets
5000
Split Beam T-Shoe
5001
Split Beam T-Shoe w/ End Gussets
5010
Split Beam T-Shoe w/U-Bolts
5011
Split Beam T-Shoe w/U-Bolts w/ End Gussets
5020
Split Beam T-Shoe w/Clamps
5021
Split Beam T-Shoe w/Clamps w/ End Gussets
5100
Fabricated T-Shoe
5101
Fabricated T-Shoe w/ End Gussets
5110
Fabricated T-Shoe w/U-Bolts
5111
Fabricated T-Shoe w/U-Bolts w/ End Gussets
5120
Fabricated T-Shoe w/Clamps
5121
Fabricated T-Shoe w/Clamps w/ End Gussets
5200
Double Upright T-Shoe
5201
Double Upright T-Shoe w/ End Gussets
5210
Double Upright T-Shoe w/U-Bolts
5211
Double Upright T-Shoe w/U-Bolts w/ End Gussets
5220
Double Upright T-Shoe w/Clamps
5221
Double Upright T-Shoe w/Clamps w/ End Gussets
Type
Description of Slot Options
S1
No Slots
S2
Expansion Slots
S3
Insulation Band Slots
S4
Expansion Slots & Insulation Band Slots
Type
Description of Slide Bearings
Type
Description of Guide Support
NSB
No Slide Bearing
NG
No Guide
T/T
PTFE on PTFE
CG
Clip Guide
S/T
Stainless Steel on PTFE
AG
Angle Guide
S/P
Stainless Steel on Polyethylene
AG2
Angle Guide 2
S/G
Stainless Steel on Graphite
AG&ST
Angle Guide and Line Stop
G/G
Graphite on Graphite
Pipe Shoe Variables 1. Pipe Diameter — Single Upright Pipe Shoes are available for pipe diameters from 1/2” to 24”, depending upon the type of pipe shoe. Single Upright Pipe Shoes for larger pipe diameters are available upon request. Double Upright Pipe Shoes are available for pipe diameters from 10” to 42”, depending upon the type of pipe shoe. Double Upright Pipe Shoes for smaller and larger pipe diameters are available upon request.
Page 5
PIPE SHOES Pipe Shoe Variables (cont’d) 2. Pipe Shoe Fig. No. — Select from any of the pipe shoe configurations as described in the following pages. 3. BOP & Length — Typical BOP’s are 4”, 6” or 8”, however, the BOP can be defined by you to fit your requirements. Please note that as shoes become shorter in height, there is a minimum height for U-Bolt-on pipe shoes because of the U-Bolt extending downwards below the top of the shoe. Clamp-on pipe shoes also have minimums because of the clearance required to install the closure bolts.
Also, as the height of the shoe becomes larger, the lateral strength of the pipe shoe becomes less. The length of the pipe shoe is typically 6”, 12”, 18”, 24”, 30” & 36” with 12 & 18 being by far the most common lengths defined by our customers. However, the shoe length can be specified by the customer. Lengths and heights can be defined in inches or millimeters, but the units must be specified. 4. Slot Option — Slot options of S1 through S4 are available for selection. The most commonly selected slots are “No Slots” and “Insulation Band Slots”. Expansion slots can be provided in cases where your pipe is operating at a very high temperature and the shoe will not expand as much as the pipe. The danger is the shearing of the weld between the pipe and the shoe. Expansion slots allow the shoe to flex as the pipe grows in order to reduce the potential of shear failure in the weld between the pipe and the shoe. Please note that slots of any kind reduce the strength of any pipe shoe. Enter “S1” if you do not want any slots of any type. 5. Slide Bearing — See the listing of Slide Bearing options available above. Steel on steel is a frequently selected option. To specify steel on steel as your option, enter “NSB” for No Bearing. 6. Material Specification — Enter the ASTM Material Specification. Default is A-36 Carbon Steel. If the Material specification is omitted, AAA Technology will fabricate the pipe shoes of A-36 steel. 7. Material Finish — The finish options available are: Plain, HDG (Hot Dip Galvanized), Primed (default primer is red oxide, however the customer may specify the primer desired, Painted (customer to define the paint specification desired) or custom whereby the customer is to define the coating. 8. Guide Type — See the listing of Guide Type options available above. Further specification of guide properties may be required as discussed further in this document.
SLOT OPTION DETAIL
Type S1, No Slots
Type S2, Expansion Slots
Type S3, Insulation Slots
Type S4, Expansion & Insulation Slots
AAA Technology & Specialties Co., Inc.
Page 6
PIPE SHOES Selecting the Best Pipe Shoe for Your Application 1. Determine if pipe shoes can be welded to the pipe or must be mechanically attached to the pipe. a. If the shoe can be welded to the pipe, then determine what the pipe material is so that the pipe shoe material can be properly welded to the pipe. b. If welding is exotic and will require specialized welding in the field, it may be more cost effective to select a mechanically attached pipe shoe design. c. If field welding is not allowed or preferred, then opt for a mechanically attached pipe shoe. 2. Determine the Loading Requirements for the pipe shoe. In other words, how much vertical load, lateral load and axial load is to be carried by the pipe shoe? If the lateral and axial loads to be carried are minimal, then a single upright, unreinforced pipe shoe will likely be satisfactory for your application. So long as the shoe is not too tall, the allowable for the pipe shoe can be calculated simply as force/area. Keep in mind that the length of the shoe support surface in contact with the support member can reduce the support area for this calculation. Further, the weakest part of your support system may be the contact point of the pipe and the pipe shoe and may not be the pipe shoe at all. The allowable loads listed for the pipe shoes in this catalog are based upon the full length of the pipe shoe being in contact with the supporting member. Reduce the allowables appropriately for your support conditions. The material and the operating temperature can also effect the allowable stress and therefore the allowable loads that can be carried. 3. See the Selection Logic on the following page to assist in selecting the best pipe shoe for your application
Selection Logic Weld-on 1. Material Requirements — The material for a weld-on pipe shoe should match the pipe material. Typically, A-36 is acceptable for being welded to A-53 and A-106 pipe, but the project specifications or the customer should be consulted for material acceptability. 2. Pipe Shoe Finish — In areas where corrosion is prevalent, a hot dip galvanizing is frequently called for. Please note that galvanized pipe shoes (welded or mechanically attached) should not be used on stainless steel pipe. 3. Loading — a. Where vertical loads exceed the allowables based upon the support member length, thicker vertical uprights should be specified and/or end gussets. b. Where lateral loads are more than minimal (this varies with the loading and the shoe), end gussets are generally recommended. c. Where axial loads are more than minimal (this varies with the loading and the shoe), end gussets are generally recommended. 4. Split Beam or Fabricated Shoe — Shoes made from split beam are generally slightly lighter than those fabricated from plate or flat bar. They are also made of dual rated beam that means that the stress rating will be 50,000 psi rather than 36,000 psi as in shoes fabricated from standard carbon steel plate or flat bar. Shoes made of split carbon steel beam are generally less expensive than pipe shoes constructed of plate or flat bar because of the additional cutting, welding and grinding involve in fabricating a shoe from plate or flat bar. 5. Slide Bearings — In order to minimize lateral and axial loads carried by the pipe shoe if guides and line stops are not specified, consider adding a low friction slide bearing. See AAA Technology’s TRI*SLIDE literature for details that will assist you in specifying the correct slide bearing for your application.
Page 7
PIPE SHOES Selection Logic (cont’d) Clamp-on / U-Bolt-on (Mechanically Attached) 1. Material Requirements — Mechanically-attached pipe shoes are typically manufactured of a compatible material or will be specified with a liner that will separate the shoe from the pipe. Typically, A-36 is acceptable for use on carbon steel pipe such as A-53 and A-106 pipe. If stronger shoes are required, pressure vessel grade material can be requested. For higher temperature lines, pipe shoes should be fabricated of alloy steel or stainless steel but the project specifications or the customer should be consulted for material acceptability. 2. Pipe Shoe Finish — In areas where corrosion is prevalent, a hot dip galvanizing is frequently called for. Please note that galvanized pipe shoes that are mechanically attached should not be used on stainless steel pipe. 3. Loading — a. Where vertical loads exceed the allowables based upon the support member length, thicker vertical uprights should be specified and/or end gussets. b. Where lateral loads are more than minimal (this varies with the loading and the shoe), end gussets are generally recommended. c. In general, clamp-on shoes will carry more lateral load than U-Bolt-on shoes. For allowable loads for U -Bolt-on shoes, see U-Bolt allowable lateral loads. Clamp-on shoes will carry lateral loads if type AG or CG is used with the clamp-on shoe. d. Where axial loads are more than minimal (this varies with the loading and the shoe), end gussets are generally recommended. 4. Split Beam or Fabricated Shoe — Shoes made from split beam are generally slightly lighter than those fabricated from plate or flat bar. They are also made of dual rated beam that means that the stress rating will be 50,000 psi rather than 36,000 psi as in shoes fabricated from standard carbon steel plate or flat bar. Shoes made of split carbon steel beam are generally less expensive than pipe shoes constructed of plate or flat bar because of the additional cutting, welding and grinding involve in fabricating a shoe from plate or flat bar. 5. Slide Bearings — In order to minimize lateral and axial loads carried by the pipe shoe if guides and line stops are not specified, consider adding a low friction slide bearing. See AAA Technology’s TRI*SLIDE literature for details that will assist you in specifying the correct slide bearing for your application.
GUIDE DETAIL
Type NG, No Guide
Type AG, Angle Guide
Type AG&ST, Angle Guide & Line Stop
Type AG2, Angle Guide 2
Type CG, Clip Guide
AAA Technology & Specialties Co., Inc.
Page 8
PIPE SHOES
SLIDE BEARING OPTION DETAIL
Property Compressive Strength Maximum Temperature
T/T PTFE over PTFE
S/T SS over PTFE
GS/GS Graphite S over Graphite S
GHT/GHT Graphite HT over Graphite HT
SS/GS SS over Graphite S
SS/GS SS over Graphite HT
SS/M—SS over Meehanite
2000 PSI
4000 PSI
7200 PSI
2800 PSI
7200 PSI
2800 PSI
24,000 PSI
300° F (150° C)
300° F (150° C)
750° F (400° C)
1200° F (650° C)
750° F (400° C)
1200° F (650° C)
1600° F (871° C)
Option PTFE over PTFE
Option Graphite over Graphite
Option SS over Meehanite
Option SS over PTFE
Option SS over Graphite
Optional Frame around Graphite or Meehanite
Page 9
PIPE SHOES
BASE PLATE DETAIL L (in) Single Upright Shoes (e.g. Fig Double Upright Shoes (e.g. Fig 5000, 5100 etc.) 5200) Pipe Size
T (in)
Type NG
2 2 1/2 3 4 6 8 10 12 14 16 18 20 24 30 36 42
1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2" 1/4" or 3/8 or 1/2"
6 6 6 6 6 6 6 10 10 10 10 12 12 ----
Type AG Type AG Type CG Type NG Type CG or AG2 or AG2 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 10 3/4 10 3/4 10 3/4 10 3/4 12 3/4 12 3/4 ----
8 1/4 8 1/4 8 1/4 8 1/4 8 1/4 8 1/4 8 1/4 12 1/4 12 1/4 12 1/4 12 1/4 14 1/4 14 1/4 ----
------8 10 10 12 12 14 14 19 1/2 22 1/2 25 1/2
------8 3/4 10 3/4 10 3/4 12 3/4 12 3/4 14 3/4 14 3/4 20 1/4 23 1/4 26 1/4
------10 1/4 12 1/4 12 1/4 14 1/4 14 1/4 16 1/4 16 1/4 21 3/4 24 3/4 27 3/4
Type NG Base Plate
Type AG or AG2 Base Plate
Different lengths, widths and thicknesses available upon request.
Type CG Base Plate
AAA Technology & Specialties Co., Inc.
Page 10
PIPE SHOES HOW TO ORDER Standard Pipe Shoe Guides and Stops are ordered by indicating the following dimensions and choices:
Page 11
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5000 SPLIT BEAM PIPE SHOE
(All slot options are available with each pipe shoe) APPLICATION: The Fig 5000 Pipe Shoe is to be welded to the pipe along the top edge & the base can also be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from a split beam of A-992 steel. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig.5000 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
A (in)
BOP to TOS (in)
H (in)
4 4 4 4 4 4 4 4 4 4 4 4 4 4 6.5 6.5 6.5 6.5 8 8
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 12.00 12.00 12.00 12.00 15.50 15.50
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 13.00 13.00 13.00 13.00 20.00 20.00
AAA Technology & Specialties Co., Inc.
Page 12
PIPE SHOES FIG. 5001 SPLIT BEAM PIPE SHOE W/ END GUSSETS
(All slot options are available with each pipe shoe) APPLICATION: The Fig 5001 Pipe Shoe with End Gusset Plates is to be welded to the pipe along the top edges of the shoe and the gussets and the base can also be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from a split beam of A-992 steel with End Gussets of A-36 Plate. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig.5001 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
A (in)
BOP to TOS (in)
H (in)
4 4 4 4 4 4 4 4 4 4 4 4 4 4 6.5 6.5 6.5 6.5 8 8
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 5000 5000 5000 5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 8.73 16.78 16.78 16.78 16.78 21.23 21.23
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 11.22 19.90 19.90 19.90 19.90 28.28 28.28
Page 13
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5010 SPLIT BEAM PIPE SHOE W/U-BOLTS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5010 Pipe Shoe is to be U-Bolted to the pipe in the U-Bolt cradles & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from a split beam of A-992 steel. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig.5010 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
D (in)
BOP to TOS (in)
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4
4 4 4 4 4 4 4 4 4
3 3 4 4 5 5 5 1/2 6 6 1/2
4 4 4 4 4 4 4 4 4
4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 6.5 6.5 6.5 6.5 8 8
7 8 1/2 9 3/4 12 14 1/2 16 1/2 18 20 22 1/4 24 1/4 28 1/4
4 4 4 4 4 4 4 4 4 4 4
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
H (in) 4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
7.22 7.22 7.36 7.66 7.84 7.94 8.30 8.66 9.39 10.10 10.46 14.78 16.10 25.70 33.30 39.90 42.60 55.20 64.70 85.10
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Capacity Wt. (lbs.) (lbs.)* 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
8.72 8.72 8.86 9.12 9.34 9.44 9.80 10.16 10.88 11.60 11.96 16.28 17.60 27.20 34.30 40.90 43.60 56.20 69.20 89.60
AAA Technology & Specialties Co., Inc.
Page 14
PIPE SHOES FIG. 5011 SPLIT BEAM PIPE SHOE W/END GUSSETS W/U-BOLTS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5011 Pipe Shoe with End Gusset Plates is to be U-Bolted to the pipe in the U-Bolt cradles & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from a split beam of A-992 steel with End Gussets of A-36 Plate. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig.5011 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 4 4 4 6.5 6.5 6.5 6.5 8 8
D (in)
BOP to TOS (in)
H (in)
3 3 4 4 5 5 5 1/2 6 6 1/2 7 8 1/2 9 3/4 12 14 1/2 16 1/2 18 20 22 1/4 24 1/4 28 1/4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.)
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
6500 6500 6500 6500 6500 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
9.45 9.45 9.59 9.89 10.07 11.13 11.63 12.33 13.53 14.73 15.33 22.53 24.73 40.73 52.28 63.28 67.78 88.78 103.23 137.23
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Capacity Wt. (lbs.) (lbs.)* 6500 6500 6500 6500 6500 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
11.94 11.94 12.08 12.38 12.56 12.66 13.02 13.38 14.10 14.82 15.18 19.50 20.82 30.42 41.20 47.80 50.50 63.10 77.48 97.88
Page 15
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5020 SPLIT BEAM PIPE SHOE W/CLAMPS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5020 Pipe Shoe is to be clamped to the pipe & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from a split beam of A-992 steel. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig.5020 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 4 4 4 6.5 6.5 6.5 6.5 8 8
D (in)
BOP to TOS (in)
H (in)
3 1/2 3 1/2 3 1/2 4 1/4 4 1/2 5 1/2" 6 1/2" 7" 7 5/8" 8 3/4" 9 3/4" 11 3/4" 13 3/4" 17" 19" 21" 23" 26" 28 1/2" 34"
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity H (in) (lbs.)* TOS (in) (lbs.)
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
7.74 7.98 8.04 8.32 8.41 8.90 9.50 10.10 11.30 12.50 13.10 20.30 22.50 38.50 47.50 58.50 63.00 84.00 97.50 131.50
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Capacity Wt. (lbs.) (lbs.)* 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
9.00 9.16 9.20 9.52 9.58 10.40 11.00 11.60 12.80 14.00 14.60 21.80 24.00 40.00 48.50 59.50 64.00 85.00 102.00 136.00
AAA Technology & Specialties Co., Inc.
Page 16
PIPE SHOES FIG. 5021 SPLIT BEAM PIPE SHOE W/END GUSSETS W/CLAMPS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5021 Pipe Shoe with End Gusset Plates is to be clamped to the pipe along the top edge & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from a split beam of A-992 steel with End Gussets of A-36 Plate. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig.5020 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. O.D. (in) (in.) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
A (in)
D (in)
BOP to TOS (in)
4 4 4 4 4 4 4 4 4 4 4 4 4 4 6.5 6.5 6.5 6.5 8 8
3 1/2 3 1/2 3 1/2 4 1/4 4 1/2 5 1/2" 6 1/2" 7" 7 5/8" 8 3/4" 9 3/4" 11 3/4" 13 3/4" 17" 19" 21" 23" 26" 28 1/2" 34"
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
H (in) 4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Load Unit Wt. BOP to Unit Wt. Capacity H (in) Capacity (lbs.)* TOS (in) (lbs.)* (lbs.) (lbs.)
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
5000 5000 5000 5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
9.97 10.21 10.27 10.55 10.64 11.13 11.93 12.33 13.53 14.73 15.33 22.53 24.73 40.73 52.28 63.28 67.78 88.78 103.23 137.23
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
5000 5000 5000 5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
12.22 12.38 12.42 12.74 12.80 13.62 14.22 14.82 16.02 17.22 17.82 25.02 27.22 43.22 55.40 66.40 70.90 91.90 110.28 130.68
Page 17
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5100 FABRICATED PIPE SHOE
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5100 Pipe Shoe is to be welded to the pipe along the top edge & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed of A-36 steel flat bar or plate welded together. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig.5100 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
A (in)
BOP to TOS (in)
H (in)
4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 10 10
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 6.58 9.87 9.87 9.87 9.87 9.87 9.87
BOP to TOS (in)
H (in)
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 8000 8000 8000 8000 8000 8000 8000
8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 8.28 12.26 12.26 12.26 12.26 12.26 12.26
AAA Technology & Specialties Co., Inc.
Page 18
PIPE SHOES FIG. 5101 FABRICATED PIPE SHOE W/ END GUSSETS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5101 Pipe Shoe with End Gusset Plates is to be welded to the pipe along all top edges & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from of A-36 steel flat bar or plate welded together. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig.5101 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 10 10
BOP to TOS (in)
H (in)
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 5000 5000 5000 5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 8.81 14.65 14.65 14.65 14.65 15.60 15.60
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 11.50 17.09 17.09 17.09 17.09 17.09 17.09
Page 19
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5110 FABRICATED PIPE SHOE w/U-BOLTS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5110 Pipe Shoe is to be U-Bolted to the pipe in the U-Bolt cradles & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from of A-36 steel flat bar or plate welded together. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions.
EXAMPLE: 3” - Fig. 5110 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 10 10
D (in)
BOP to TOS (in)
H (in)
3 1/2 3 1/2 3 1/2 4 1/4 4 1/2 5 5 1/2 6 6 1/2 7 8 1/2 9 3/4 12 14 1/2 16 1/2 18 20 22 1/4 24 1/4 28 1/4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.)
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000
7.30 7.30 7.44 7.74 7.92 8.02 8.29 8.74 9.46 10.18 10.54 14.86 16.18 25.78 31.17 37.77 40.47 53.07 59.07 79.47
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000
9.00 9.00 9.14 9.44 9.62 9.72 10.08 10.44 11.16 11.88 12.24 16.56 17.88 27.48 33.56 40.16 42.86 55.46 61.46 81.86
AAA Technology & Specialties Co., Inc.
Page 20
PIPE SHOES FIG. 5111 FABRICATED PIPE SHOE W/END GUSSETS w/ U-BOLTS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5111 Pipe Shoe with End Gusset Plates is to be U-Bolted to the pipe in the U-Bolt cradles & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from of A-36 steel flat bar or plate welded together. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5110 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. O.D. A (in) (in) (in.)
D (in)
BOP to TOS (in)
H (in)
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.)
H (in)
Load Unit Wt. Capacity (lbs.)* (lbs.)
1/2 3/4
.84 1.05
4 4
3 1/2 3 1/2
4 4
4 7/16 4 19/32
5000 5000
9.53 9.53
6 6
6 7/16 6 19/32
5000 5000
12.22 12.22
1
1.315
4
3 1/2
4
4 11/16
5000
9.67
6
6 11/16
5000
12.36
1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 10 10
4 1/4 4 1/2 5 5 1/2 6 6 1/2 7 8 1/2 9 3/4 12 14 1/2 16 1/2 18 20 22 1/4 24 1/4 28 1/4
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
9.97 10.15 10.25 10.61 10.97 11.69 12.41 12.77 17.09 18.41 28.01 35.95 42.55 45.25 57.85 64.80 85.20
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
5000 5000 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
12.66 12.84 12.94 13.30 13.66 14.38 15.10 15.46 19.78 21.10 30.70 38.39 44.99 47.69 60.29 66.29 86.69
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
Page 21
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5120 FABRICATED PIPE SHOE W/ PIPE CLAMPS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5120 Pipe Shoe is to be clamped to the pipe & the base can be welded to the support member to anchor the
pipe. CONSTRUCTION: The Pipe Shoe is constructed of A-36 steel flat bar or plate welded and assembled together. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5120 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 10 10
D (in)
BOP to TOS (in)
H (in)
3 1/2 3 1/2 3 1/2 4 1/4 4 1/2 5 1/2" 6 1/2" 7" 7 5/8" 8 3/4" 9 3/4" 11 3/4" 13 3/4" 17" 19" 21" 23" 26" 28 1/2" 34"
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.)
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
7.82 8.06 8.12 8.40 8.49 8.98 9.58 10.18 11.38 12.58 13.18 20.38 22.58 38.58 45.37 56.37 60.87 81.87 91.87 125.87
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 5000 5000 5000 5000 5000 6000 6000 6000 8000 8000 8000 8000 8000 8000 8000
9.28 9.44 9.48 9.80 9.86 10.68 11.28 11.88 13.08 14.28 14.88 22.08 24.28 40.28 47.76 58.76 63.26 84.26 94.26 128.26
AAA Technology & Specialties Co., Inc.
Page 22
PIPE SHOES FIG. 5121 FABRICATED PIPE SHOE W/END GUSSETS W/PIPE CLAMPS
(All slot options are available with each pipe shoe)
APPLICATION: The Fig. 5121 Pipe Shoe with End Gusset Plates is to be clamped to the pipe & the base can be welded to the support member to anchor the pipe. CONSTRUCTION: The Pipe Shoe is constructed from of A-36 steel flat bar or plate welded together.. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5120 - 4”x12” - S1 - T/T - AG
Nominal Actual Pipe Dia. O.D. A (in) (in) (in.) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24
.84 1.05 1.315 1.66 1.9 2.375 2.875 3.5 4 4.5 5.5625 6.625 8.625 10.75 12.75 14 16 18 20 24
4 4 4 4 4 4 4 4 4 4 4 4 4 4 8 8 8 8 10 10
D (in)
BOP to TOS (in)
H (in)
3 1/2 3 1/2 3 1/2 4 1/4 4 1/2 5 1/2" 6 1/2" 7" 7 5/8" 8 3/4" 9 3/4" 11 3/4" 13 3/4" 17" 19" 21" 23" 26" 28 1/2" 34"
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
4 7/16 4 19/32 4 11/16 4 13/16 4 15/16 5 3/16 5 7/16 5 3/4 6 6 1/4 6 25/32 7 5/16 8 5/16 9 3/8 10 3/8 11 12 13 14 16
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 6500 6500 6500 6500 6500 6500 6500 6500 6500 6500 7800 7800 7800 10400 10400 10400 10400 10400 10400 10400
* - Weights shown are for 12” long shoes * - For pipe shoes larger than 24” NPS, contact AAAT for further assistance.
10.05 10.29 10.35 10.63 10.72 11.21 11.81 12.41 13.61 14.81 15.41 22.61 24.81 40.81 50.15 61.15 65.65 86.65 97.60 131.60
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
H (in) 6 7/16 6 19/32 6 11/16 6 13/16 6 15/16 7 3/16 7 3/16 7 3/4 8 8 1/4 8 25/32 9 5/16 10 5/16 11 3/8 12 3/8 13 14 15 16 18
Load Unit Wt. Capacity (lbs.)* (lbs.) 5000 5000 5000 5000 5000 12000 14000 15000 15000 18000 18000 18000 24000 29000 30000 34000 38000 41000 41000 47000
12.50 12.66 12.70 13.02 13.08 13.90 14.50 15.10 16.30 17.50 18.10 25.30 27.50 43.50 52.59 63.59 68.09 89.09 99.09 133.09
Page 23
713-849-3366 | www.aaatech.com |
[email protected]
PIPE SHOES FIG. 5200 DOUBLE UPRIGHT PIPE SHOE
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5200 Shoe is to be welded to the pipe along the two top edges. To anchor the shoe, the base can also be welded to the support structure beneath. CONSTRUCTION: The Pipe Shoe is constructed of A-36 steel flat bar or plate welded together. The two side uprights are welded to the middle gusset as well as to the base. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: lengths.
The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different
ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5200 - 4”x12” - S1/GP - T/T - AG
Nominal Actual Pipe Dia. O.D. (in.) (in) 10 12 14 16 18 20 22 24 30 36 42
10.75 12.75 14 16 18 20 22 24 30 36 42
A (in)
BOP to TOS (in)
H (in)
6 8 8 10 10 12 12 12 17 1/2 20 1/2 23 1/2
4 4 4 4 4 4 4 4 4 4 4
9 3/8 10 3/8 11 12 13 14 15 16 19 22 25
* - Weights shown are for 12” long shoes
Load Unit Wt. Capacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
11.89 16.4 20.38 23.7 27.18 30.56 33.9 36.96 43.36 48.46 53.57
BOP to TOS (in)
H (in)
6 6 6 6 6 6 6 6 6 6 6
11 3/8 12 3/8 13 14 15 16 17 18 21 24 27
Load Unit Wt. Capacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
13.67 18.86 23.44 27 31.3 35.15 38.99 41.4 48.56 54.28 60.01
Page 24
AAA Technology & Specialties Co., Inc.
PIPE SHOES FIG. 5201 DOUBLE UPRIGHT PIPE SHOE WITH END GUSSETS
(All slot options are available with each pipe shoe)
APPLICATION: The Fig. 5201 Shoe is to be welded to the pipe along the two top longitudinal edges and on the accessible edges of the gusset to pipe intersections. To anchor the shoe, the base can also be welded to the support structure beneath. CONSTRUCTION: The Pipe Shoe is constructed of A-36 steel flat bar or plate welded together. The two end gussets and two side uprights are all welded on the upright seams as well as to the base. The middle gusset is welded to the side uprights. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5200 - 4”x12” - S1/GP - T/T - AG
Nominal Actual Pipe Dia. O.D. (in.) (in) 10 12 14 16 18 20 22 24 30 36 42
10.75 12.75 14 16 18 20 22 24 30 36 42
A (in)
BOP to TOS (in)
H (in)
6 8 8 10 10 12 12 12 17 1/2 20 1/2 23 1/2
4 4 4 4 4 4 4 4 4 4 4
9 3/8 10 3/8 11 12 13 14 15 16 19 22 25
* - Weights shown are for 12” long shoes
Load Unit Wt. Capacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
11.89 16.4 20.38 23.7 27.18 30.56 33.9 36.96 43.36 48.46 53.57
BOP to TOS (in)
H (in)
6 6 6 6 6 6 6 6 6 6 6
11 3/8 12 3/8 13 14 15 16 17 18 21 24 27
Load Unit Wt. Capacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
13.67 18.86 23.44 27 31.3 35.15 38.99 41.4 48.56 54.28 60.01
Page 25
PIPE SHOES FIG. 5210 DOUBLE UPRIGHT PIPE SHOE w/U-BOLTS
(All slot options are available with each pipe shoe)
APPLICATION: The Fig. 5210 Shoe is to be U-Bolted to the pipe. To anchor the shoe, the base can also be welded to the support structure beneath. Note that U-Bolts will not restrain high anchor loads. CONSTRUCTION: The Pipe Shoe is constructed of A-36 steel flat bar or plate welded together. The two side uprights are welded to the middle gusset as well as to the base and the U-Bolt cradles. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: lengths.
The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different
ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5210 - 4”x12” - S1/GP - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 10 12 14 16 18 20 22 24 30 36 42
10.75 12.75 14 16 18 20 22 24 30 36 42
6 8 8 10 10 12 12 12 17 1/2 20 1/2 23 1/2
D (in)
BOP to TOS (in)
14 1/2 16 1/2 18 20 22 1/4 24 1/4 26 1/4 28 1/4 34 1/4 40 1/4 46 1/4
4 4 4 4 4 4 4 4 4 4 4
* - Weights shown are for 12” long shoes
Load Unit Wt. BOP to H (in) Capacity (lbs.)* TOS (in) (lbs.)
H (in)
9 3/8 10 3/8 11 12 13 14 15 16 19 22 25
11 3/8 12 3/8 13 14 15 16 17 18 21 24 27
19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
19.77 33.18 36.98 42.18 50.78 59.76 62.06 64.36 88.96 112.46 129.57
6 6 6 6 6 6 6 6 6 6 6
Load CaUnit Wt. pacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
23.15 36.56 40.36 45.56 54.16 64.86 67.16 69.46 95.76 119.26 136.37
Page 26
AAA Technology & Specialties Co., Inc.
PIPE SHOES FIG. 5211 DOUBLE UPRIGHT PIPE SHOE w/U-BOLTS WITH END GUSSETS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5211 Shoe is to be U-Bolted to the pipe. To anchor the shoe, the base can also be welded to the support structure beneath. Note that U-Bolts will not restrain high anchor loads. CONSTRUCTION: The Pipe Shoe is constructed of two end gussets and two side uprights that are all welded on the upright seams as well as to an A-36 base. The uprights and gussets are also welded to the two U-Bolt cradles. The middle gusset is welded to the side uprights as well. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig. 5210 - 4”x12” - S1/GP - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 10 12 14 16 18 20 22 24 30 36 42
10.75 12.75 14 16 18 20 22 24 30 36 42
6 8 8 10 10 12 12 12 17 1/2 20 1/2 23 1/2
D (in)
BOP to TOS (in)
H (in)
14 1/2 16 1/2 18 20 22 1/4 24 1/4 26 1/4 28 1/4 34 1/4 40 1/4 46 1/4
4 4 4 4 4 4 4 4 4 4 4
9 3/8 10 3/8 11 12 13 14 15 16 19 22 25
* - Weights shown are for 12” long shoes
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
19.77 33.18 36.98 42.18 50.78 59.76 62.06 64.36 88.96 112.46 129.57
6 6 6 6 6 6 6 6 6 6 6
H (in) 11 3/8 12 3/8 13 14 15 16 17 18 21 24 27
Load CaUnit Wt. pacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
23.15 36.56 40.36 45.56 54.16 64.86 67.16 69.46 95.76 119.26 136.37
Page 27
PIPE SHOES FIG. 5220 DOUBLE UPRIGHT PIPE SHOE w/CLAMPS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5220 Shoe is to be clamped to the pipe along the top edges of the shoe. To anchor the shoe, the base can also be welded to the support structure beneath. CONSTRUCTION: The Pipe Shoe is constructed of two braced vertical flat bars or plates welded on a A -36 steel base. The middle gusset is welded to the side uprights as well. To anchor the shoe, the base can also be welded to the support structure beneath. FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different lengths. ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig.5220 - 4”x12” - S1/GP - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in) 10 12 14 16 18 20 22 24 30 36 42
10.75 12.75 14 16 18 20 22 24 30 36 42
6 8 8 10 10 12 12 12 17.5 20.5 23 1/2
D (in)
BOP to TOS (in)
H (in)
17 19 21 23 26 28 31 33 3/4 41 3/4 48 1/2 57 1/2
4 4 4 4 4 4 4 4 4 4 4
9 3/8 10 3/8 11 12 13 14 15 16 19 22 25
* - Weights shown are for 12” long shoes
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
43.49 55.66 66.76 74.58 96.02 111.94 130 147.00 241.64 355.00 510.00
6 6 6 6 6 6 6 6 6 6 6
H (in) 11 3/8 12 3/8 13 14 15 16 17 18 21 24 27
Load CaUnit Wt. pacity (lbs.)* (lbs.) 19000 19000 19000 26000 26000 26000 26000 35000 38000 41000 44000
46.87 59.04 70.14 77.96 99.4 117.04 135.5 152.1 248.44 365.00 525.00
AAA Technology & Specialties Co., Inc.
Page 28
PIPE SHOES FIG. 5221 DOUBLE UPRIGHT PIPE SHOE w/CLAMPS w/ END GUSSETS
(All slot options are available with each pipe shoe) APPLICATION: The Fig. 5221 Shoe is to be clamped to the pipe along the top edge. To anchor the shoe, the base can also be welded to the support structure beneath. CONSTRUCTION: The Pipe Shoe is constructed of two end gussets and two side uprights that are all welded on the upright seams as well as to an A-36 base. The uprights and gussets are also welded to the two bottom pipe clamp halves. The middle gusset is welded to the side uprights as well.
FINISH: The Pipe Shoe can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: lengths.
The Pipe Shoe can be supplied in different BOP to TOS dimensions as well as different
ORDERING: See beginning of this section for ordering instructions. EXAMPLE: 3” - Fig.5221 - 4”x12” - S1/GP - T/T - AG
Nominal Actual Pipe Dia. A (in) O.D. (in.) (in)
D (in)
BOP to TOS (in)
H (in)
Load Unit Wt. BOP to Capacity (lbs.)* TOS (in) (lbs.)
H (in)
Load Unit Wt. Capacity (lbs.)* (lbs.)
10
10.75
6
17
4
9 3/8
19000
43.49
6
11 3/8
19000
46.87
12
12.75
8
19
4
10 3/8
19000
55.66
6
12 3/8
19000
59.04
19000
66.76
6
13
19000
70.14
14
14
8
21
4
11
16
16
10
23
4
12
26000
74.58
6
14
26000
77.96
26000
96.02
6
15
26000
99.4
18
18
10
26
4
13
20
20
12
28
4
14
26000
111.94
6
16
26000
117.04
26000
130
6
17
26000
135.5
22
22
12
31
4
15
24
24
12
33 3/4
4
16
35000
147.00
6
18
35000
152.1
38000
241.64
6
21
38000
248.44
6 6
24
41000
365.00
27
44000
525.00
30
30
17.5
41 3/4
4
19
36
36 42
20.5 23 1/2
48 1/2 57 1/2
4 4
22
41000
355.00
25
44000
510.00
42
* - Weights shown are for 12” long shoes
Page 29
PIPE SADDLES FIG. 5500 HEAVY DUTY PIPE SADDLE
APPLICATION: The Fig. 5500 Heavy Duty Pipe Saddle is used to support large diameter pipe. CONSTRUCTION: The Saddle is constructed of A-36 carbon steel. FINISH: The Saddle can be provided with a black, painted or hot dip galvanized finish. OPTIONAL FEATURES: The Saddle can be supplied in different dimensions upon request. ORDERING: To order, specify pipe size, figure number, desired finish and any non -standard dimensions. EXAMPLE: 20” - Fig.6000 - Painted
Pipe Size
R (IN)
A (IN)
20
10
22
B
C (IN)
T (IN)
T2 (IN)
T3 (IN)
6
14 3/8
1/2
3/8
---
20
6
15 3/8
1/2
3/8
---
23 1/2
20
6
16 3/8
1/2
3/8
---
13
25 1/2
20
6
17 3/8
1/2
3/8
---
14
27
20
6
18 3/8
1/2
3/8
---
30
15
29
20
6
19 1/2
5/8
1/2
1/2
32
16
31
20
6
20 1/2
5/8
1/2
1/2
34
17
32
20
6
20 1/2
5/8
1/2
1/2
36
18
34
20
6
22 1/2
5/8
1/2
1/2
38
19
36
20
6
22 1/2
5/8
1/2
1/2
40
20
38
20
6
24 1/2
5/8
1/2
1/2
42
21
40
20
6
26 1/2
5/8
1/2
1/2
48
24
46
20
6
32 1/2
5/8
1/2
1/2
54
27
52
20
6
36 1/2
5/8
1/2
1/2
60
30
58
20
6
40 1/2
5/8
1/2
1/2
WIDE
STD.
20 1/2
20
11
22
24
12
26 28
AAA TECHNOLOGY & SPECIALTIES CO., INC. 6219 Brittmoore Road ▪ Houston, Texas 77041-5114, U.S.A. Telephone: 713-849-3366 ▪ FAX: 713-849-3654 E-mail:
[email protected] ▪ Website: http://www.aaatech.com
P I P E H A N G E R S , S U P P O RT S , R E S T R A I N T S & FA B R I C AT I O N
EQUAL™ HI-LOAD BOX SPRINGS
EQUAL™ HYDRAULIC SNUBBER ASSEMBLIES
EQUAL™ ENGINEERED CONSTANT SPRING HANGERS
EQUAL™ RIGID SWAY STRUT ASSEMBLIES
EQUAL™ LIMIT STOPS
EQUAL™ DAMPERS & SWAY BRACES
VIBRATION CONTROL HOLD DOWN CLAMPS
EQUAL™ LARGE DIA. ROLLERS
TRI*FOAM & TRI*CAL INSULATED SUPPORTS
HANGER HARDWARE & AN EXTENSIVE INVENTORY OF HANGER COMPONENTS
THREADED HANGER RODS
ADJUSTABLE PIPE STANDS
PIPE SHOES, GUIDES & LINE STOPS
TRI-SLIDE™ LOW FRICTION BEARINGS
FABRICATED TO YOUR SPECIFICATION
CORROSION RESISTANT
Associated Services Offered
Piping Stress Analysis Services - Need to know what pipe supports to select or why the loads on EQUAL™ ENGINEERED VARIABLE SPRING HANGERS
your equipment or the stresses in your piping system are too high? We can perform a TRIFLEX ® piping stress analysis and tell you and we can recommend solutions. Pipe Hanger Fitness for Service Studies - Need to sort out whether the pipe supports and spring hangers in your plant are performing as originally intended or if corrosion has affected their ability to perform? We can help make these determinations and provide you with complete documentation as well as offer recommendations for improvements.