PIPING DESIGN & ARRANGEMENT

Institute of Bioproduct Development UNIVERSITI TEKNOLOGI MALAYSIA

MS ISO/IEC 17025 TESTING SAMM NO. 433

PIPING DESIGN & ARRANGEMENT 10 - 12 Sept 2013 or 21 - 23 Oct 2013 IBD, UTM Kuala Lumpur

COURSE OBJECTIVES

This course provides the necessary knowledge for those who are responsible for designing and constructing a new piping system, particularly on offshore environment, and those who oversee and ensure the integrity of existing piping system. The objectives of this course are to enable participants to:

1. Understand Pipe Routing & Arrangement Design Concepts & Requirements. 2. Understand Pipe Support Design Concept, and Pipe Span Requirements. 3. Understand P&ID & PFD for Piping Arrangement Design. 4. Understand Piping Stress Isometric for Pipe Support Design . 5. Understand General Pipe Flexibility and Pipe Stress Requirements. 6. Understand General Piping Material Requirements.

After completing this subject the participants should be able to:

1. Perform piping arrangement and layout design as normal engineering practices & piping code requirements. 2. Perform pipe support design. 3. Generate, review and check of piping isometric drawings. 4. Generate & review piping & valve specifications, piping materials & valve data sheets , piping material take off (MTO). 5. Review & perform general piping material selection. 6. Perform simple pipe flexibility studies and review pipe stress analysis report.

COURSE CONTENT

COURSE DESCRIPTION The course will review the basic requirements of Piping Arrangement & Pipe Support Design with emphasis on pipe routing design practices and requirements on compressor , pump , heat exchanger , air cooler, vessel, flare system piping layout. A general overview of piping material , pipe flexibility and pipe stress requirements will be included in this course. Application of these concepts include practical case studies on offshore piping layout, piping material selection, MTO review , pipe stress studies, and general Piping Fit For Life (FFS ) Study as per ASME B31.3 requirements.

Who Should Attend... Engineer, Senior Piping Designer, Piping Designer, Plant Supervisors & Operator, Piping inspectors and party with involvement on process piping working in Oil & Gas , Chemical Plant, Power industries, etc.

Day 1 : Piping Material 1. General Piping Material . 2. Piping Standard , & Introduction to ASME B31.3. 3. Pipes Fittings & Components 4. Flange Design & Selection 5. Piping Class & Piping Material Specification 6. Pipe Thickness Calculation 7. Valves- Concept, Selection & Data Sheet 8. Piping MTO. 9. Piping System – Fit For Services 10. Case Studies Day 2 : Piping Equipment Layout & Arrangement 1. PFD, P& ID considerations in Piping Design 2. Piping Design & Arrangement Requirement 3. Standard & Special Pipe Support 4. Piping Equipment Layout & Arrangement: Compressor Piping; Pump Piping; Heat Exchanger Piping; Air Cooler Piping; Vertical & Horizontal Vessel Piping 5. Piping Interfaces : Process/ Structure/ Mechanical /Electrical 6. Piping Drawings Piping GA, Pipe Support Location Plan, Isometric, etc. Day 3 : Pipe Stress Analysis 1. Fundamental Theory & Concept of Pipe Stress Analysis 2. Pipe Flexibilities & Calculation 3. Piping Force & Moment, Friction, Stress Intensification Factor, Elbow Flexibilities 4. Pipe Expansion Loop 5. Pipe Failure Theory & Code Requirements 6. Load Cases- Sustain, Operation, Thermal, Occasional 7. Spring Design & Selection 8. Stress Isometric Interpretation 9. Stress Analysis Inputs Parameters & Stress Analysis Report Interpretation : Code Compliance; Restraint Summary; Load Interpretation 10. Case Studies

HRDF CLAIMABLE

Staff from more than 700 local and overseas companies have attended our life-long learning programmes.

For more information please contact us at :Chemical Engineering Pilot Plant INSTITUTE OF BIOPRODUCT DEVELOPMENT UNIVERSITI TEKNOLOGI MALAYSIA

Some of these companies are : PETRONAS, SHELL, BP, SAUDI ARABIA BASIC IND. CORP. (SABIC), QATAR LNG, ALMARAI (SAUDI ARABIA), IDEMITSU, EASTMAN CHEMICALS, BASF PETRONAS, KUWAIT INSTITUTE OF SCIENTIFIC RESEARCH, KHARTOUM REFINERY, LOADSTAR(Sri Lanka) etc.

COURSE TUTOR

81310 UTM Johor Bahru, Johor, MALAYSIA Tel : +607- 553 6485 Fax : +607 - 553 6464 Attn : Ms. Nurul Asrin Email : [email protected] UTM Kuala Lumpur, Jalan Semarak, 54100 Kuala Lumpur, MALAYSIA Tel : +603 - 2615 4406 Fax : +603 - 2693 7921 Attn : Ms. Yatie Email : [email protected]

MR. SAM WEI YEOW | Mr. Sam Wei Yeow is a ASME B31.3 Code Review Committee Member, and a registered professional engineer with BEM ( Board of Engineer) Malaysia. He has 17 years of piping design and project management experiences, and has extensively involved in piping design & construction in many offshore and power plant projects with emphasis on piping equipment layout, piping arrangement & pipe support design and pipe stress analysis. He had also conducted numerous technical talks at Institute of Engineer ( IEM) , Malaysia and Offshore Technical Conference, and public course on engineering topics related to Piping Design. Mr. Sam also has a great passion in using 3D modeling in engineering design, supporting site construction, plant operation and maintenance activities.

We can offer

courses in-house at your company

PIPING DESIGN & ARRANGEMENT Please tick ( x ) where appropriate

[ ] 10 - 12 Sept 2013 IBD, UTM Kuala Lumpur

or

[

] 21 - 23 Oct 2013

Method of payment

Please kindly complete and return the reply form 3 weeks before the commencement date together with :

Job Title Name 2

Local Participants Cheque / Bank draft which are made payable to PHYTO BIZNET SDN. BHD.

Job Title COMPANY INFORMATION

Fee is inclusive of lunch, refreshments and course materials. Accommodation is not included

YES ! I would like to register the following participants Name 1

COURSE FEE

Local Participant RM3500 per participant RM3250 for 2 or more participant from the same company

Company Address Town State Tel

Fax

Email

International Participants Direct Transfer/Bank Draft: IBD Bank details: CIMB Bank Berhad, Universiti Teknologi Malaysia 81310 UTM Skudai, Johor, Malaysia Account No : 0118 - 0004178 - 05 - 7 Swift Code CIBBMYKL

Name

Cancellation & Substitutions

Tel

Fax

Email

A full refund will be promptly made for all written cancellations 2 weeks before the course. 50% refund will be made for written cancellations received 7 days before the course. A substitute may be made at any time. NOTE A) The organiser has the right to make any amendments that they deem to be in the best interest of the course and to cancel the course if insufficient registrations are received a week before course commencements date .

Signature

more info, click

www.ibd.utm.my

EURO1850

Please instruct your bank to remit us the full amount, net of bank charges

Authorised Signatory (*This registration is invalid without signature from an authorised officer)

Job Title

International Participant

B) CERTIFICATE OF ATTENDANCE will be awarded at the end of the course.

UTM Kuala Lumpur is situated about 10 minutes drive from the famous Kuala Lumpur landmark, the PETRONAS TWIN TOWER and KLCC, the prime shopping centre. It is easily accessible by road and major hotels are located nearby.