VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified and TA = 25oC. All static parameters other than IO and VO. are re
Data Sheet No. PD60107 revX
IR2133/IR2135(J&S) & (PbF) IR2233/IR2235(J&S) & (PbF) 3-PHASE BRIDGE DRIVER Features • Floating channel designed for bootstrap operation Fully operational to +600V or+1200V Tolerant to negative transient voltage dV/dt immune • Gate drive supply range from 10V/12V to 20V DC and up to 25V for transient • Undervoltage lockout for all channels • Over-current shut down turns off all six drivers • Independent 3 half-bridge drivers • Matched propagation delay for all channels • 2.5V logic compatible • Outputs out of phase with inputs • All parts are also available LEAD-FREE
Product Summary VOFFSET IO+/VOUT ton/off (typ.) Deadtime (typ.)
600V or 1200V max. 200 mA / 420 mA 10 - 20V or 12 - 20V 750/700 ns 250 ns
Packages
Description The IR2133IR2135/IR2233IR2355 (J&S) are high voltage, high speed power MOSFET and IGBT driver with three independent high side and low side referenced output channels for 3-phase applications. Propri28-Lead SOIC etary HVIC technology enables ruggedized monolithic construction. 28-Lead PDIP Logic inputs are compatible with CMOS or LSTTL outputs, down to 2.5V logic. An independent operational amplifier provides an analog 44-Lead PLCC w/o 12 leads feedback of bridge current via an external current sense resistor. A current trip function which terminates all six outputs can also be derived from this resistor. A shutdown function is available to terminate all six outputs. An open drain FAULT signal is provided to indicate that an over-current or undervoltage shutdown has occurred. Fault conditions are cleared with the FLT-CLR lead. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The floating channels can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which operates up to 600 volts or 1200 volts.
Typical Connection
up to 600V or 1200V
(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout.
www.irf.com
1
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) Absolute Maximum Ratings Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under board mounted and still air conditions. Symbol VB1,2,3 VS1,2,3 VHO1,2,3 V CC VSS VLO1,2,3 VIN
VIN,AMP VOUT,AMP VFLT dVS/dt PD
RthJA
TJ TS TL
Definition High side floating supply voltage
(IR2133/IR2135) (IR2233/IR2235) High side floating supply offset voltage High side floating output voltage Fixed supply voltage Logic ground Low side output voltage Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR)
Op amp input voltage (CA+ & CA-) Op amp output voltage (CAO) FAULT output voltage Allowable offset supply voltage transient Package power dissipation @ TA ≤ 25ºC (28 Lead PDIP) (28 Lead SOIC) (44 lead PLCC) Thermal resistance, junction to ambient (28 Lead PDIP) (28 Lead SOIC) (44 lead PLCC) Junction temperature Storage temperature Lead temperature (soldering, 10 seconds
Min.
Max.
-0.3 -0.3 VB1,2,3 - 25 VS1,2,3 - 0.3 -0.3 VCC - 25 -0.3 VSS - 0.3
625 1225 VB1,2,3 + 0.3 VB1,2,3 + 0.3 25 VCC + 0.3 VCC + 0.3 (VSS + 15) or (VCC + 0.3) whichever is lower VCC + 0.3 VCC + 0.3 VCC + 0.3 50 1.5 1.6 2.0 83 78 63 125 150 300
VSS - 0.3 VSS - 0.3 VSS - 0.3 — — — — — — — — -55 —
Units
V
V/ns W
ºC/W
ºC
Recommended Operating Conditions The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute voltages referenced to COM. The VS offset rating is tested with all supplies biased at 15V differential.
Symbol Parameter Definition VB1,2,3 VS1,2,3 VHO1,2,3 V CC VSS VLO1,2,3 VIN VIN,AMP VOUT,AMP VFLT
High side floating supply voltage High side floating supply offset voltage (IR2133/IR2135) (IR2233/IR2235) High side floating output voltage Fixed supply voltage Low side driver return Low side output voltage Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) Op amp input voltage (CA+ & CA-) Op amp output voltage (CAO) FAULT output voltage
Min.
Max.
VS1,2,3 + 10/12 VS1,2,3 + 20 Note 1 600 Note 1 1200 VS1,2,3 VB1,2,3 10 or 12 20 -5 5 0 VCC VSS VSS + 5 VSS VSS + 5 VSS VSS + 5 VSS VCC
Units
V
Note 1: Logic operational for VS of COM - 5V to COM + 600V/1200V. Logic state held for VS of COM -5V to COM -VBS. (Please refer to the Design Tip DT97-3 for more details). Note 2: All input pins, op amp input and output pins are internally clamped with a 5.2V zener diode.
2
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) Dynamic Electrical Characteristics VBIAS (VCC, VBS1,2,3) = 15V, VS1,2,3 = VSS, TA = 25oC and CL = 1000 pF unless otherwise specified. Symbol
Definition
Min. Typ. Max. Units Test Conditions
ton toff tr tf tsd titrip
Turn-on propagation delay Turn-off propagation delay Turn-on rise time Turn-off fall time SD to output shutdown propagation delay ITRIP to output shutdown propagation delay
500 450 — — 500 600
750 700 90 40 750 850
1000 950 150 70 1000 1100
tbl
ITRIP blanking time
—
400
—
tflt
ITRIP to FAULT propagation delay
400
650
900
tfil,in
Input filter time (HIN, LIN and SD)
—
310
—
tfltclr DT SR+ SR-
VIN = 0 & 5V VS1,2,3 = 0 to 600V or 1200V
ns
VIN,VSD = 0 & 5V VIN,VITRIP = 0 & 5V ITRIP = 1V VIN,VITRIP = 0 & 5V VIN = 0 & 5V
FLT-CLR to FAULT clear time
600
850
1100
VIN,VITRIP = 0 & 5V
Deadtime, LS turn-off to HS turn-on & HS turn-off to LS turn-on Amplifier slew rate (positive) Amplifier slew rate (negative)
100
250
400
VIN = 0 & 5V
5 2
10 2.5
— —
V/µs
NOTE: For high side PWM, HIN pulse width must be ≥ 1µ sec
Static Electrical Characteristics VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified and TA = 25oC. All static parameters other than IO and VO are referenced to VSS and are applicable to all six channels (HS1,2,3 & LS1,2,3). The VO and IO parameters are referenced to COM and VS1,2,3 and are applicable to the respective output leads: HO1,2,3 or LO1,2,3. Symbol
Definition
VIH VIL VFCLR,IH VFCLR,IL VSD,TH+ VSD,THVIT,TH+ VIT,THVOH VOL ILK
Logic “0” Input Voltage (OUT = LO) Logic “1” Input Voltage (OUT = HI) Logic “0” Fault Clear Input Voltage Logic “1” Fault Clear Input Voltage SD Input Positive Going Threshold SD Input Negative Going Threshold IITRIP Input Positive Going Threshold IITRIP Input Negative Going Threshold High Level Output Voltage, VBIAS - VO Low Level Output Voltage, VO Offset Supply Leakage Current (IR2133/IR2135) (IR2233/IR2235) Quiescent VBS Supply Current Quiescent VCC Supply Current Logic “1” Input Bias Current (OUT = HI) Logic “0” Input Bias Current (OUT = LO) “High” Shutdown Bias Current “Low” Shutdown Bias Current “High” IITRIP Bias Current “Low” IITRIP Bias Current
IQBS IQCC IIN+ IINISD+ ISDIITRIP+ IITRIPwww.irf.com
Min. 2.2 — 2.2 — 1.6 1.4 470 360 — — — — — — — — — — — —
Typ. Max. Units — — — — 1.9 1.7 570 460 — — — — 50 4 200 100 30 — 30 —
— 0.8 — 0.8 2.2 2.0 670 560 100 100 50 50 100 8 350 250 100 100 100 100
Test Conditions
V
mV
µA mA µA nA µA nA
VIN = 0V, IO = 0A VIN = 5V, IO = 0A VB1,2,3=VS1,2,3 = 600V VB1,2,3=VS1,2,3 = 1200V VIN = 0V or 5V VIN = 0V or 5V VIN = 0V VIN = 5V SD = 5V SD = 0V IITRIP = 5V IITRIP = 0V 3
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) Static Electrical Characteristics — Continued VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified and TA = 25oC. All static parameters other than IO and VO are referenced to VSS and are applicable to all six channels (HS1,2,3 & LS1,2,3). The VO and IO parameters are referenced to COM and VS1,2,3 and are applicable to the respective output leads: HO1,2,3 or LO1,2,3. Symbol Parameter Definition
Min. Typ. Max. Units Test Conditions
I FLTCLR+ “High” Fault Clear Input Bias Current
—
200
350
I FLTCLR- “Low” Fault Clear Input Bias Current
—
100
250
VBSUV+
VBSUV-
VBSUVH
V CCUV+
VCCUV-
V CCUVH
FLT-CLR = 0V µA
FLT-CLR = 5V
VBS Supply Undervoltage Positive Going Threshold (for IR2133/IR2233)
7.6
8.6
9.6
(for IR2135/IR2235)
9.2
10.4
11.6
(for IR2133/IR2233)
7.2
8.2
9.2
(for IR2135/IR2235)
8.3
9.4
10.5
(for IR2133/IR2233)
—
0.4
—
(for IR2135/IR2235)
—
1
—
VBS Supply Undervoltage Negative Going Threshold
VBS Supply Undervoltage Lockout Hysteresis
V
VCC Supply Undervoltage Positive Going Threshold (for IR2133/IR2233)
7.6
8.6
9.6
(for IR2135/IR2235)
9.2
10.4
11.6
(for IR2133/IR2233)
7.2
8.2
9.2
(for IR2135/IR2235)
8.3
9.4
10.5
VCC Supply Undervoltage Negative Going Threshold
VCC Supply Undervoltage Lockout Hysteresis (for IR2133/IR2233)
—
0.4
—
(for IR2135/IR2235)
—
1
—
—
70
100
Ω
Ron,FLT
FAULT- Low On Resistance
IO+
Output High Short Circuit Pulsed Current
200
250
—
IO-
Output Low Short Circuit Pulsed Current
420
500
—
mA
VOS
Amplifier Input Offset Voltage
—
0
30
mV
CA+=0.2V, CA-=CAO
IIN,AMP
Amplifier Input Bias Current
—
—
4
nA
CA+ = CA- = 2.5V
CMRR
Amplifier Common Mode Rejection Ratio
50
70
—
PSRR
Amplifier Power Supply Rejection Ratio
50
70
—
dB
CA+=0.2V, CA-=CAO VCC = 10V & 20V
5
5.2
5.4
V
CA+ = 1V, CA- = 0V
mV
VOH,Amp Amplifier High Level Output Voltage
—
—
20
I SRC,Amp Amplifier Output Source Current
4
7
—
I SNK,Amp Amplifier Output Sink Current
VOL,Amp
Amplifier Low Level Output Voltage
0.5
1
—
IO+,Amp
Amplifier Output High Short Circuit Current
—
10
—
IO-,Amp
Amplifier Output Low Short Circuit Current
—
4
—
4
VOUT = 0V, VIN = 0V PW ≤ 10 µs VOUT = 15V, VIN = 5V PW ≤ 10 µs
CA+ = 0.1V & 5V, CA- = CAO
CA+ = 0V, CA- = 1V CA+ = 1V, CA- = 0V, CAO = 4V CA+ = 0V, CA- = 1V, CAO = 2V
mA
CA+ = 5V, CA- = 0V, CAO = 0V CA+ = 0V, CA- = 5V, CAO = 5V www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) Functional Block Diagram
Lead Definitions Symbol
Lead Description
HIN1,2,3
Logic inputs for high side gate driver outputs (HO1,2,3), out of phase.
LIN1,2,3
Logic inputs for low side gate driver outputs (LO1,2,3), out of phase.
FAULT
Indicates over-current or undervoltage lockout (low side) has occurred, negative logic.
VCC
Logic and low side fixed supply.
ITRIP
Input for over-current shut down.
FLT-CLR
Logic input for fault clear, negative logic.
SD
Logic input for shut down.
CAO
Output of current amplifier.
CA-
Negative input of current amplifier.
CA+
Positive input of current amplifier.
VSS
Logic ground.
COM
Low side return.
VB1,2,3
High side floating supplies.
HO1,2,3
High side gate drive outputs.
VS1,2,3
High side floating supply returns.
LO1,2,3
Low side gate drive outputs
www.irf.com
5
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) Lead Assignments
ITRIP
FAULT
ITRIP
FAULT
FLT-CLR
LIN3
FLT-CLR
LIN3
CAO
LIN2
CAO
LIN2
CA-
LIN1
CA-
LIN1
CA+
HIN3
CA+
HIN3
SD
HIN2
SD
HIN2
VSS
HIN1
VSS
HIN1
COM
VCC
COM
VCC
LO3
VB1
LO3
VB1
LO2
HO1
LO2
HO1
LO1
VS1
LO1
VS1
VS3
VB2
VS3
VB2
HO3
HO2
HO3
HO2
VB3
VS2
VB3
VS2
28 Lead DIP
44 Lead PLCC w/o 12 Leads IR2133J IR2135J IR2233J IR2235J
IR2133 IR2135
28 Lead SOIC (Wide Body) IR2133S IR2135S IR2233S IR2235S
Part Number
HIN1,2,3
LIN1,2,3
ITRIP
SD FLT-CLR
FAULT
HO1,2,3
LO1,2,3
Figure 1. Input/Output Timing Diagram
6
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
HIN
HIN LIN ton
LIN
toff
tr 90%
50%
50%
50%
50%
tf
LO
90%
50%
50%
HO
HO LO
10%
10%
DT
Figure 2. Switching Time Waveform Definitions
DT
Figure 3. Deadtime Waveform Definitions
FLT-CLR
50%
50%
ITRIP
FAULT 50%
50%
Any Output 50%
tflt
tfltclr titrip
Figure 4. Overcurrent Shutdown Waveform
t in,fil
U
t in,fil
50% HIN/LIN
on off
on
off
on off
high HO/LO
low
Figure 4.5. Input Filter Function
www.irf.com
SD tsd
HO LO
90%
Figure 5. Shutdown Waveform Definitions
7
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
1500 Turn-on Delay Time (ns)
Turn-on Delay Time (ns)
1500 1200 900
M ax.
Typ.
600 M in.
300 0 -50
1200
M ax.
900
Typ.
600
M in.
300 0
-25
0
25
50
75
100
125
10
12.5
Temperature (oC)
1500
1200
Turn-Off Time (ns)
Turn-on Delay Time (ns)
20
Figure 6B. Turn-On Time vs. Voltage
1500
M ax.
900 Typ.
600
M in.
300
2.5
3
3.5
4
4.5
1200 900
M ax.
Typ.
600 M in.
300 0 -50
0 5
-25
0
25
50
75
100
125
Temperature ( C) o
Input Voltage (V) Figure 6C. Turn-On Time vs. Input Voltage
Figure 7A. Turn-Off Time vs. Temperature 1500
1500 1200
Turn-Off Time (ns)
Turn-Off Time (ns)
17.5
Supply Voltage (V)
Figure 6A. Turn-On Time vs. Temperature
M ax.
900
Typ.
600
M in.
1200 M ax.
900 Typ.
600
M in.
300
300
0
0 10
8
15
12.5
15
17.5
20
2.5
3
3.5
4
4.5
Supply Voltage (V)
Input Voltage (V)
Figure 7B. Turn-Off Time vs. Voltage
Figure 7C. Turn-Off Time vs. Input Voltage
5
www.irf.com
250
250
200
200
Turn-On Rise Time (ns
Turn-On Rise Time (ns
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
150 M ax.
100 Typ.
50
M ax.
150 Typ.
100 50 0
0 -50
-25
0
25
50
75
100
10
125
12.5
Fiure 8A. Turn-On Rise Time vs.Temperature
Turn-Off Fall Time
Turn-Off Fall Time
20
150
120 90 60
M ax.
Typ.
30
120 90
M ax.
60 Typ.
30 0
0 -50
-25
0
25
50
75
100
10
125
12.5
17.5
20
Figure 9B. Turn-Off Fall Time vs. Voltage
Figure 9A. Turn-Off Fall Time vs. Temperature
1500 SD to output SD Time (ns)
1500 1200 900
15
Supply Voltage (V)
Temperature (oC)
SD to output SD Time (ns)
17.5
Fiure 8B. Turn-On Rise Time vs.Voltage
150
M ax. Typ.
600 M in.
300 0 -50
1200
M ax.
900
Typ.
600
M in.
300 0
-25
0
25
50
75
100
125
10
12.5
15
17.5
20
Temperature ( C)
Supply Voltage (V)
Figure 10A. SD to Output shutdown Time vs. Temperature
Figure 10B. SD to Output shutdown Time vs. Voltage
o
www.irf.com
15
Supply Voltage (V)
Temperature ( C) o
9
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 1500 ITRIP to FAULT Time (ns
ITRIP to FAULT Time (ns
1500 1200 900
M ax. Typ.
600
M in.
300
1200 M ax.
900 Typ.
600
M in.
300 0
0 -50
-25
0
25
50
75
100
10
125
ITRIP to output SD Time (ns
ITRIP to output SD Time (ns
1800 1500 1200 M ax.
900 Typ. M in.
300 -50
-25
0
25
50
75
100
1500 M ax.
1200 Typ.
900 M in.
600
10
125
12.5
1200 M ax.
Typ. M in.
0
25
50
75
100
125
Temperature (oC) ________ ______ Figure 13A. FLT-CLR to FAULT clear Time vs. Temperature
10
17.5
20
Figure 12B. ITRIP to output shutdow n Time vs. Voltage FLT-CLR to FAULT clear Time (ns
FLT-CLR to FAULT clear Time (ns
1500
-25
15
Supply Voltage (V)
1800
300 -50
20
300
Figure 12A. ITRIP to output shutdow n Time vs. Temperature
600
17.5
1800
Temperature (oC)
900
15
Supply Voltage (V) _____ Figure 11B. ITRIP to FAULT Time vs. Voltage
Temperature (oC) _____ Figure 11A. ITRIP to FAULT Time vs. Temperature
600
12.5
1800 1500 1200
M ax.
900
Typ.
M in.
600 300 10
12.5
15
17.5
20
Supply Voltage (V) ________ ______ Figure 13B. FLT-CLR to FAULT clear Time vs. Voltage
www.irf.com
750
750
600
600 Deadtime (ns)
Deadtime (ns)
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
450 M ax.
300 Typ.
150
450
M ax.
300
Typ.
150
M in.
M in.
0
0 -50
-25
0
25
50
75
100
10
125
12.5
Temperature (oC)
Amplifier slew rate (v/ µs)
Amplifier slew rate (v/ µs)
16 12
Typ.
8 M in.
4
16 12 Typ.
8 M in.
4 0
0 -50
-25
0
25
50
75
100
10
125
12.5
15
17.5
20
Supply Voltage (V)
Temperature (oC) Figure 15A. Amplifier slew rate (+) vs. Temperature
Figure 15B. Amplifier slew rate (+) vs. Voltage
5
5 Amplifier slew rate (v/ µs)
Amplifier slew rate (v/ µs)
20
20
20
4 3 Typ. M in.
1 0 -50
4 3 Typ.
2
M in.
1 -25
0
25
50
75
100
Temperature (oC) Figure 16A. Amplifier slew rate (-) vs. Temperature
www.irf.com
17.5
Figure 14B. Deadtime vs. Voltage
Figure 14A. Deadtime vs. Temperature
2
15
Supply Voltage (V)
125
10
12.5
15
17.5
20
Supply Voltage (V) Figure 16B. Amplifier slew rate (-) vs. Voltage
11
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 6 Logic "0" Input Voltage (V)
Logic "0" Input Voltage (V)
6 5 4 3 M in.
2
5 4 3 M in.
2 1
1 -50
-25
0
25
50
75
100
10
125
12.5
4 3 2 M ax.
0 -50
4 3 2 M ax.
1 0
-25
0
25
50
75
100
125
10
12.5
Temperatre ( C)
17.5
Figure 18A. Logic "1" Input (OUT=HI), Fault Clear Input Voltage vs. Temperature
Figure 18B. Logic "1" Input (OUT=HI), Fault Clear Input Voltage vs. Voltage
3.0
3.0 SD Input TH (+) (V)
SD Input TH (+) (V)
15
2.5 M ax. Typ. M in.
1.5 1.0 -50
20
Supply Voltage (V)
o
2.0
20
5 Logic "1" Input Voltage (V)
Logic "1" Input Voltage (V)
5
2.5 M ax.
2.0
Typ. M in.
1.5 1.0
-25
0
25
50
75
100
Temperatre ( C) o
Figure 21A. SD Input TH(+) vs. Temperature
12
17.5
Figure 17B. Logic "0" Input Voltage (OUT=LO), Fault Clear Voltage vs. Voltage
Figure 17A. Logic "0" Input Voltage (OUT=LO), Fault Clear Voltage vs. Temperature
1
15
Supply Voltage (V)
Temperature ( C) o
125
10
12.5
15
17.5
20
Supply Voltage (V) Figure 21B. SD Input TH(+) vs. Voltage
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 3.0 SD Input TH (-) (V)
SD Input TH (-) (V)
3.0 2.5 M ax.
2.0
Typ.
1.5
M in.
1.0 -50
2.5 M ax.
2.0
Typ.
1.5
M in.
1.0 -25
0
25
50
75
100
125
10
12.5
Temperatre ( C) Figure 22A. SD Input TH(-) vs. Temperature
IITRIP Input TH (+) (mV)
M ax.
600
Typ. M in.
400 200 -50
800 M ax.
600
Typ. M in.
400 200
-25
0
25
50
75
100
125
10
12.5
Temperature ( C) Figure 23A. IITRIP Input TH(+) vs. Temperature
17.5
20
Figure 23B. IITRIP Input TH(+) vs. Voltage 900 IITRIP Input TH (-) (mV)
900 IITRIP Input TH (-) (mV)
15
Supply Voltage (V)
o
700 M ax. Typ. M in.
300 100 -50
700 M ax.
500
Typ. M in.
300 100
-25
0
25
50
75
100
125
Temperature (oC) Figure 24A. IITRIP Input TH(-) vs.Temperature
www.irf.com
20
1000
800
500
17.5
Figure 22B. SD Input TH(-) vs. Voltage
1000 IITRIP Input TH (+) (mV)
15
Supply Voltage (V)
o
10
12.5
15
17.5
20
Supply Voltage (V) Figure 24B. IITRIP Input TH(-) vs. Voltage
13
0.5 0.4 0.3 0.2 0.1
M ax.
0.0 -50
-25
0
25
50
75
100
125
Temperature (oC)
High Level Output Voltage (V)
High Level Output Voltage (V)
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
0.5 0.4 0.3 0.2 M ax.
0.1 0.0
10
0.3 0.2 0.1
M ax.
0 -50
-25
0
25
50
75
100
125
Temperature (oC)
300 200 100 M ax.
0 -50 -25
0
25
50
75 100 125
Temperature (oC)
Figure 27A. Offset Supply Leakage Current vs. Temperature
14
Offset Supply Leakage Current (µA)
Offset Supply Leakage Current (µA)
400
20
0.5 0.4 0.3 0.2 M ax.
0.1 0 10
12.5
15
17.5
20
Supply Voltage (V)
Figure 26B. Low Level Output vs. Voltage
Figure 26A. Low Level Output vs. Temperature
500
17.5
Figure 25B. High Level Output vs. Voltage
Low Level Output Voltage (V)
Low Level Output Voltage (V)
0.4
15
Supply Voltage (V)
Figure 25A. High Level Output vs. Temperature
0.5
12.5
500 400 300 200 100
M ax.
0 0
100
200
300
400
500
600
Supply Voltage (v)
Figure 27B. Offset Supply Leakage Current vs. Voltage
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 250 V Supply Current (µΑ)
V Supply Current (µΑ)
250 200 150 100 50
M ax.
Typ.
0 -50
200 150 100 M ax.
50
Typ.
0 -25
0
25
50
75
100
125
10
12.5
Temperature ( C) Figure 28A. VBS Supply Current vs. Temperature
V cc Supply Current (µA)
V cc Supply Current (µA)
12 8
M ax.
4
Typ.
0 -50
16 12 8
M ax.
4
Typ.
0 -25
0
25
50
75
100
125
10
12.5
Temperature ( C) Figure 29A. V cc Supply Current vs. Temperature Logic "1" Input Current (µA)
600 400 M ax. Typ.
-25
0
25
50
75
17.5
20
Figure 29B. V cc Supply Current vs. Voltage
800
0 -50
15
Supply Voltage (V)
o
Logic "1" Input Current (µA)
20
20
16
100
125
Temperature (oC) Figure 30A. Logic "1" Input Bais Current vs. Temperature
www.irf.com
17.5
Figure 28B. V BS Supply Current vs. Voltage
20
200
15
Supply Voltage (V)
o
800 600 400 M ax.
200
Typ.
0 10
12.5
15
17.5
20
Supply Voltage (V) Figure 30B. Logic "1" Input Bais Current vs. Voltage
15
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 800 Logic "0" Input Current (µA)
Logic "0" Input Current (µA)
800 600 400 200
M ax. Typ.
0 -50
-25
0
25
50
75
100
600 400 200
M ax. Typ.
0
125
10
12.5
Temperature ( C) Figure 31A. Logic "0" Input Bais Current vs. Temperature
"High" SD Bais Current (µA)
"High" SD Bais Current (µA)
200
M ax. Typ.
0 -50
-25
0
25
50
75
100
300 200 100
M ax.
Typ.
0 10
125
500 400 300 200 M ax.
-25
0
25
50
15
17.5
20
Figure 32B. "High" Shutdow n Bais Current vs. Supply Voltage "Low" SD Bais Current (nA)
"Low" SD Bais Current (nA)
Figure 32A. "High" Shutdow n Bais Current vs. Temperature
0 -50
12.5
Supply Voltage (V)
Temperature ( C) o
75
100
Temperature ( C) o
Figure 33A. "Low" Shutdow n Bais Current vs. Temperature
16
20
400
300
100
17.5
Figure 31B. Logic "0" Input Bais Current vs. Supply Voltage
400
100
15
Supply Voltage (V)
o
125
500 400 300 200 100
M ax.
0 10
12.5
15
17.5
20
Supply Voltage (V) Figure 33B. "Low " Shutdown Bais Current vs. Supply Voltage
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
"High" IITRIP Bias Current (µA)
"High" IITRIP Bias Current (µA)
400 300 200 100 M ax. Typ.
0 -50
-25
0
25
50
75
100
400 300 200 100
M ax.
Typ.
0 10
125
12.5
Figure 34A. "High" IITRIP Bais Current vs. Temperature
"Low" I ITRIP Bais Current (nA)
"Low" I ITRIP Bais Current (nA)
400 300 200 M ax.
-25
0
25
50
75
100
500 400 300 200 100
M ax.
0
125
10
12.5
Figure 35A. "Low" IITRIP Bais Current vs. Temperature
Figure 35B. "Low " IITRIP Bais Current vs. Supply Voltage
400 M ax. Typ.
-25
0
25
50
75
100
125
Temperature ( C) o
Figure 36A. "High" Fault Clear Input Bais Current vs. Temperature
"High" Fault Clear Input Current µ( A)
"High" Fault Clear Input Current µ( A)
600
www.irf.com
17.5
Supply Voltage (V)
800
0 -50
15
Temperature ( C) o
200
20
Figure 34B. "High" IITRIP Bais Current vs. Supply Voltage
500
0 -50
17.5
Supply Voltage (V)
Temperature (oC)
100
15
20
800 600 400 M ax.
200
Typ.
0 10
12.5
15
17.5
20
Supply Voltage (V) Figure 36B. "High" Fault Clear Input Bais Current vs. Supply voltage
17
800 600 400 200
M ax. Typ.
0 -50
-25
0
25
50
75
100
125
"Low" Fault Clear Input Current (µA)
"Low" Fault Clear Input Current (µA)
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 800 600 400 200
M ax. Typ.
0 10
12.5
Temperature ( C) Figure 37A. "Low" Fault Clear Input Bais Current vs. Temperature
V BS UV Th (+) (V)
V BS UV Th (+) (V)
M ax.
M in.
8 6 -50
-25
0
25
50
75
100
11 M ax.
9 8
Typ. M in.
6 -50
125
-25
0
Figure 38A. IR2135/IR2235 VBS Undervoltage Threshold (+) vs. Temperature
75
100
125
Figure 38B. IR2133/IR2233 V BS Undervoltage Threshold (+) vs. Temperature
14
12 V UV TH (+) (V)
V UV TH (+) (V)
50
Temperature ( C)
Temperature ( C)
12 M ax. Typ. M in.
8 6 -50
-25
0
25
50
75
100
Temperature ( C) o
Figure 39A. IR2135/IR2235 VBS Undervoltage Threshold (-) vs. Temperature
18
25
o
o
10
20
12
Typ.
10
17.5
Figure 37B. "Low" Fault Clear Input Bais Current vs. Supply Voltage
14 12
15
Supply Voltage (V)
o
125
11 M ax.
9 M in.
8
Typ.
6 -50
-25
0
25
50
75
100
125
Temperature ( C) o
Figure 39B. IR2133/IR2233 V BS Undervoltage Threshold (-) vs. Temperature
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 12 V cc UV TH (+) (V)
V cc UV TH (+) (V)
14 13 M ax.
11
Typ.
10
M in.
8 -50
-25
0
25
50
75
100
11 M ax.
9
Typ.
M in.
8
6 -50
125
-25
0
25
Temperature (oC) Figure 40A. IR2135/IR2235 Vcc Undervoltage Threshold (+) vs. Temperature
V cc UV TH (+) (V)
V cc UV TH (+) (V)
100
125
12 M ax.
11
Typ.
9 M in.
8 6 -50
-25
0
25
50
75
100
11 M ax.
9 Typ.
8
M in.
6 -50
125
-25
0
25
Temperature ( C) Figure 41A. IR2135/IR2235 V cc Undervoltage Threshold (-) vs. Temperature FAULT-Low On Resistance (Ω )
150 100 M ax. Typ.
50
-25
0
25
50
75
100
125
Figure 41B. IR2133/IR2233 Vcc Undervoltage Threshold (-) vs. Temperature
200
0 -50
50
Temperature (oC)
o
FAULT-Low On Resistance (Ω)
75
Figure 40B. IR2133/IR2233 V cc Undervoltage Threshold (+) vs. Temperature
12
75
100
Temperature ( C) o
Figure 42A. FAULT- Low On Resistance vs. Temperature
www.irf.com
50
Temperature ( oC)
125
150 120
M ax.
90
Typ.
60 30 0 10
12.5
15
17.5
20
Supply Voltage (V) Figure 42B. FAULT- Low On Resistance vs. Supply Voltage
19
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 500 Output Source Current (mΑ)
Output Source Current (mΑ)
500 400 Typ.
300
M in.
200 100 0 -50
-25
0
25
50
75
100
400 300 Typ.
200
M in.
100 0 10
125
12.5
Temperature ( C) o
Output Sink Current (mΑ)
Output Sink Current (mΑ)
1000
800 600
Typ. M in.
400 200 0 -50
800 600 Typ.
400
M in.
200 0
-25
0
25
50
75
100
125
10
12.5
Figure 44A. Ourput Sink Current vs. Temperature
Figure 44B. Ourput Sink Current vs. Supply Voltage
70 50 M ax.
Typ.
-25
0
25
50
75
100
Temperature ( C) o
Figure 45A. Amplifier Input Offest Voltage vs. Temperature
125
Amplifier Input Offset Voltage (mV)
Amplifier Input Offset Voltage (mV)
17.5
Supply Voltage (V)
90
-10 -50
15
Temperature ( C) o
20
20
Figure 43B. Output Source Current vs. Supply Voltage
1000
10
17.5
Supply voltage (V)
Figure 43A. Output Source Current vs. Temperature
30
15
20
90 70 50 30 10
M ax.
Typ.
-10 10
12.5
15
17.5
20
Supply Voltage (V) Figure 45B. Amplifier Input Offest Voltage vs. Supply Voltage
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF) 150 Amplifier CMRR (dB)
Amplifier CMRR (dB)
150 120 90 Typ.
60
M in.
30 0 -50
120 90 Typ.
60
M in.
30 0
-25
0
25
50
75
100
125
10
12.5
Temperature (oC) Figure 46A. Amplifier Common Mode Rejection Ratio vs. Temperature
Amplifier PSRR (dB)
Amplifier PSRR (dB)
75
Typ. M in.
50 25 0 -50
100 75
Typ. M in.
50 25 0
-25
0
25
50
75
100
125
10
12.5
Temperature ( C)
15
17.5
20
Supply Voltage (V)
o
Figure 47A. Amplifier Pow er Supply Rejection Ratio vs. Temperature
Figure 47B. Amplifier Power Supply Rejection Ratio vs. Supply Voltage 50
6.0 5.7
Amplifier V OL (V)
Amplifier V OH (V)
20
125
100
M ax. Typ.
5.1
M in.
40 30 20
M ax.
10
4.8
0
4.5 10
12.5
15
17.5
20
Supply Voltage (V) Figure 48. Amplifier High Level Output Voltage vs. Supply Voltage
www.irf.com
17.5
Figure 46B. Amplifier Common Mode Rejection Ratio vs. Supply Voltage
125
5.4
15
Supply Voltage (V)
10
12.5
15
17.5
20
Supply Voltage (V) Figure 49. Amplifier Low Level Output Voltage vs. Supply Voltage
21
15
Amplifier ISNK (V)
Amplifier ISRC(V)
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
12 9 6
Typ.
3
M in.
0
2.5 2.0 1.5 1.0 0.5
Typ. M in.
0.0 10
12.5
15
17.5
20
10
12.5
Supply Voltage (V)
20
Amplifier IO- (V)
Amplifier IO+ (V)
20
Figure 51. Amplifier Output Sink Current vs. Supply Voltage
16
Typ.
4 0
20 16 12 8 4
Typ.
0 10
12.5
15
17.5
Supply Voltage (V)
Figure 52. Amplifier Output High Short Circuit Current vs. Supply Voltage
22
17.5
Supply Voltage (V)
Figure 50. Amplifier Output Source Current vs. Supply Voltage
12 8
15
20
10
12.5
15
17.5
20
Supply Voltage (V)
Figure 53. Amplifier Output Low Short Circuit Current vs. Supply Voltage
www.irf.com
480V 320V 160V 0V
1E+3
1E+4
Ju n tio n T e m p e ratu re (°C )
120 110 100 90 80 70 60 50 40 30 20 1E+2
1E+5
120 110 100 90 80 70 60 50 40 30 20 1E+2
480 320V 160 0V
1E+3
1E+4
1E+5
Frequency (Hz)
Frequency (Hz)
Figure 7. IR2133J Junction Temperature vs Frequency Driving (IRGPC20KD2) Rgate = 5.1Ω @ Vcc = 15V
Figure 8. IR2133J Junction Temperature vs Frequency Driving (IRGPC30KD2) Rgate = 5.1Ω @ Vcc = 15V
120 110 100 90 80 70 60 50 40 30 20 1E+2
150 140 130 120 110 100 90 80 70 60 50 40 30 20 1E+2
480V 320V 160V 0V
1E+3
1E+4
1E+5
Ju n ctio n T e m p e ratu re (°C )
Ju n ctio n T e m p e ratu re (°C )
Ju n tio n T e m p e ratu re (°C )
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
480V
320V
160V 0V
1E+3
1E+4
1E+5
Frequency (Hz)
Frequency (Hz)
Figure 9. IR2133J Junction Temperature vs Frequency Driving (IRGPC40KD2) Rgate = 5.1Ω @ Vcc = 15V
Figure 10. IR2133J Junction Temperature vs Frequency Driving (IRGPC50KD2) Rgate = 5.1Ω @ Vcc = 15V
www.irf.com
23
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
500
300V
0V
1E+3
1E+4
Ju n ctio n T e m p e ratu re (°C )
Ju n ctio n T e m p e ratu re (°C )
900V 120 110 100 90 80 70 60 50 40 30 20 1E+2
1E+5
1120 1110 1100 90 80 70 60 50 40 30 20 1E+2
900V 500V
300
0V
1E+3
1E+4
Frequency (Hz)
Frequency (Hz)
Figure 11. IR2233J Junction Temperature vs Frequency Driving (IRG4PH30KD) Rgate = 20Ω @ Vcc = 15V
Figure 12. IR2233J Junction Temperature vs Frequency Driving (IRG4PH40KD) Rgate = 15Ω @ Vcc = 15V
900V 500V 300V
120 110 100 90 80 70 60 50 40 30 20 1E+2
300V
0V
1E+3
1E+4
1E+5
Ju n ctio n T e m p e ratu re (°C )
Ju n ctio n T e m p e ratu re (°C )
900V 500V
24
1E+5
120 110 100 90 80 70 60 50 40 30 20 1E+2
0V
1E+3
1E+4
1E+5
Frequency (Hz)
Frequency (Hz)
Figure 13. IR2233J Junction Temperature vs Frequency Driving (IRG4PH50KD) Rgate = 10Ω @ Vcc = 15V
Figure 14. IR2233J Junction Temperature vs Frequency Driving (IRG4ZH71KD) Rgate = 5Ω @ Vcc = 15V
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
Package Dimensions
28-Lead PDIP (wide body)
01-6011 01-3024 02 (MS-011AB)
NOTES
28-Lead SOIC (wide body) www.irf.com
01-6013 01-3040 02 (MS-013AE)
25
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
44-Lead PLCC w/o 12 leads
26
01-6009 00 01-3004 02(mod.) (MS-018AC)
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S)&(PbF)
LEADFREE PART MARKING INFORMATION Part number
Date code
IRxxxxxx YWW?
Pin 1 Identifier ? P
MARKING CODE Lead Free Released Non-Lead Free Released
IR logo
?XXXX Lot Code (Prod mode - 4 digit SPN code)
Assembly site code Per SCOP 200-002
ORDER INFORMATION Basic Part (Non-Lead Free) 28-Lead PDIP IR2133 order IR2133 2 8-Lead SOIC IR2133S order IR2133S 28-Lead PDIP IR2135 order IR2135 28-Lead SOIC IR2135S order IR2135S 28-Lead PDIP IR2233 not available 28-Lead SOIC IR2233S order IR2233S 28-Lead PDIP IR2235 not available 28-Lead SOIC IR2235S order IR2235S 44-Lead PLCC IR2133J order IR2133J 44-Lead PLCC IR2135J order IR2135J 44-Lead PLCC IR2233J order IR2233J 44-Lead PLCC IR2235J order IR2235J
Leadfree Part 28-Lead PDIP 28-Lead SOIC 28-Lead PDIP 28-Lead SOIC 28-Lead PDIP 28-Lead SOIC 28-Lead PDIP 28-Lead SOIC 44-Lead PLCC 44-Lead PLCC 44-Lead PLCC 44-Lead PLCC
IR2133 IR2133S IR2135 IR2135S IR2233 IR2233S IR2235 IR2235S IR2133J IR2135J IR2233J IR2235J
order order order order order order order order order order order order
IR2133PbF IR2133SPbF IR2135PbF IR2135SPbF IR2233PbF IR2233SPbF IR2235PbF IR2235SPbF IR2133JPbF IR2135JPbF IR2233JPbF IR2235JPbF
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 This product has been qualified per industrial level Data and specifications subject to change without notice. 9/22/2005
www.irf.com
27