This document is a compendium of the basic data relating to resistance
thermometer sensors and thermocouples. *This second edition reflects IEC and
JIS ...
Technical Information
Resistance Thermometer Sensor and Thermocouple Data Collection
Introduction Resistance thermometer sensors (RTSs) and thermocouples are the temperature sensors most widely used in industrial temperature measurement. They have the advantages of simple construction and ease of use, making for convenience in measurement. However, if correct application methods based on the proper standards are not followed, highly accurate measurements cannot be expected. This document is a compendium of the basic data relating to resistance thermometer sensors and thermocouples. *This second edition reflects IEC and JIS revisions (thermocouples) of July 1995. We hope that this document will aid you in comparing the various underlying standards from an international viewpoint, and in deciding which standards to follow. This document also provides information on vital parameters such as operating temperature ranges and tolerances.
Contents 1. RESISTANCE THERMOMETER SENSORS .................................................................................................. 1 1.1
Overview of the IEC Revisions ........................................................................................................................................ 1
1.2
Overview of the JIS Revisions .......................................................................................................................................... 1
1.3
Types of Resistance Thermometer Sensors ...................................................................................................................... 3
1.4
Tolerances vs. Temperature .............................................................................................................................................. 3
1.5
Temperature/Resistance relationships Values in Various Nations ................................................................................... 4
1.6
Copper Resistance Thermometer Sensors ......................................................................................................................... 5
2. THERMOCOUPLES ............................................................................................................................................ 6 2.1
Overview of the JIS '95 Revisions .................................................................................................................................... 6
2.2
Types of Thermocouples ................................................................................................................................................... 7
2.3
Thermal EMF Characteristics ......................................................................................................................................... 10
2.4
Tolerance ......................................................................................................................................................................... 11
2.5
Themocouple Electrical Characteristics .......................................................................................................................... 11
2.6
Thermocouple operating Limits ...................................................................................................................................... 12
2.7
Thermocouple Leadwire Resistances .............................................................................................................................. 13
3. MINERAL INSULATED THERMOCOUPLES ............................................................................................. 14 3.1
Construction ..................................................................................................................................................................... 14
3.2
Tolerances ........................................................................................................................................................................ 15
3.3
Codes and Normal Operating Limits .............................................................................................................................. 16
3.4
Electrical Characteristics ................................................................................................................................................. 17 (Insulation Resistance, Thermocouple Leadwire Resistance) ........................................................................................ 17
4. EXTENTION AND COMPENSATING CABLE ............................................................................................ 18 5. INTERNATIONAL TEMPERATURE SCALE .............................................................................................. 20 5.1
International Temperature Scale Plan ............................................................................................................................. 20
5.2
Essentials of the 1990 International Temperature Scale (ITS-90) ................................................................................. 21
5.3
Influence of ITS-90 on Industrial Thermometers ........................................................................................................... 22
TI 6B0A1-01E Yokogawa Electric Corporation
© Copyright Oct. 1990 (YK) 3rd Edition: May 2003 (YG)
APPENDIX A RESISTANCE THERMOMETER SENSORS APPENDIX TABLE A1
PT100 REFERENCE RESISTANCE TABLE .......................................................................... 24
APPENDIX TABLE A2
JPT100 REFERENCE RESISTANCE TABLE ........................................................................ 26
APPENDIX TABLE A3
RT50 REFERENCE RESISTANCE TABLE ........................................................................... 28
APPENDIX TABLE A4
PT100 REFERENCE RESISTANCE TABLE .......................................................................... 30
APPENDIX TABLE A5
INTERPOLATION EQUATION FOR PT100 REFERENCE RESISTANCE ........................ 32
APPENDIX TABLE A6
INTERPOLATION EQUATION FOR JPT100 REFERENCE RESISTANCE ....................... 32
APPENDIX B THERMOCOUPLES APPENDIX TABLE B1
TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 33
APPENDIX TABLE B2
TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 37
APPENDIX TABLE B3
TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 41
APPENDIX TABLE B4
TYPE N THERMOCOUPLE THERMAL E.M.F. TABLE ..................................................... 45
APPENDIX TABLE B5
TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE ..................................................... 48
APPENDIX TABLE B6
TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 52
APPENDIX TABLE B7
TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE ....................................................... 55
APPENDIX TABLE B8
TYPE T THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 58
APPENDIX TABLE B9
INTERPOLATION EQUATION OF REFERENCE THERMAL E.M.F. of JIS'95 (JIS C1602-1995) ....................................................................................................................... 60
APPENDIX TABLE B10
TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 68
APPENDIX TABLE B11
TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 72
APPENDIX TABLE B12
TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 76
APPENDIX TABLE B13
TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE ..................................................... 80
APPENDIX TABLE B14
TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 84
APPENDIX TABLE B15
TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE ....................................................... 87
APPENDIX TABLE B16
TYPE T THERMOCOUPLE THERMAL E.M.F. TABLE ...................................................... 90
APPENDIX TABLE B17.
INTERPOLATION EQUATION OF REFERENCE THERMAL E.M.F. of JIS'81 (JIS C1602-1981, abolished after July 1995) ............................................................................ 92
APPENDIX TABLE B18
Cu-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE U) ............... 96
APPENDIX TABLE B19
Fe-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE L) ................ 98
APPENDIX TABLE B20
W (W5Re/W26Re) THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE (ASTM E988) ........................................................................................................................... 101
APPENDIX TABLE B21
KP/Au•Fe THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE ......................... 105
APPENDIX TABLE B22
TABLE OF THERMOCOUPLE REFERENCE THERMAL E.M.F. PRACTICED IN TABLES OTHER THAN THOSE DEFINED IN JIS. ........................................................... 106
TI 6B0A1-01E
1. Resistance Thermometer Sensors Resistance thermometer sensors (RTSs) are temperature sensors that make use of the physical property where electrical resistance in metal increases proportionally with an increase in temperature. Since platinum RTSs can be expected to provide the most accurate temperature measurement of all industrial temperature sensors, they are widely used, especially in conditions near room temperature. One of the requirements for an industrial thermometer sensor is that its performance and characteristics be guaranteed by a standard. Platinum RTSs have been standardized under JIS C 1604 ("Resistance Thermometer Sensors") and JIS C 1606 ("Sheathed Resistance Thermometer Sensors") in Japan, and standardized under IEC-751 ("Industrial Platinum Resistance Thermometer Sensors") abroad. These standards were recently revised one after another. This document explains the revisions and summarizes the essential data based on the new standards.
1.1 Overview of the IEC Revisions IEC-751 was revised in July, 1995. The major change in this revision is to revise reference resistance in accordance with the temperatures of the 1990 International Temperature Scale (ITS-90). ITS-90 has adopted as the new International Temperature Scale since January 1, 1990 (Refer to 5. International Temperature Scale of this document). IEC had started study to revise IEC-751 reference resistance immediately after ITS-90 adoption, and finally accomplished.
1.2 Overview of the JIS Revisions Resistance thermometer sensors JIS was revised in February, 1997. This revision made JIS C 1604 completely conform to IEC-751. The major changes are as follows. (1) JIS for Resistance thermometer sensors is uniformed to JIS C 1604 (Resistance thermometer sensors) and JIS C 1606 (Sheathed resistance thermometer sensors) is abolished. (2) Reference resistance table is revised to conform to IEC standard. In the new JIS, reference resistance table is revised in accordance with the temperatures of the 1990 International Temperature Scale (ITS-90) which is adopted in IEC standard. As for the new resistance reference resistance table, refer to Table A5 Resistance table at the end of this document. Figure 1 shows the difference between reference resistance values of JIS'89 Pt100 and those of JIS'95 Pt100. For example, when the measured temperature is 100˚C, the difference is +0.027˚C, at 300˚C, it is +0.083˚C and at 500˚C, 0.242˚C. This difference is bigger than the temperature difference between the old International Temperature Scale (IPTS-68) and ITS-90 (Refer to 5.3 Influence of ITS-90 on Industrial Thermometers). Comparing the temperature differences to the tolerances at measured value 500˚C, it is about one fifth of the tolerance in class A, and less than one tenth in class B, so their influence can be ignored on a practical industrial use level. However, in using digital device which resolution is 0.1˚C or less than that, the influence cannot be ignored. (3) JPt100, which has used for many years in Japan, is abolished. JPt100, which has unique reference resistance values of Japan, is abolished in the new JIS. With regard to JPt100, it was already announced that it would be abolished in the future at the last time revision (January, 1989). However, considering the
TI 6B0A1-01E
1
situation that they have been used for more than thirty years and many of them are still in use, the 1989 reference resistance table remains in the guide. It is also described in the guide that the characteristics of JPt100 are almost the same as those of Pt100 so that the quality of supplement is guaranteed. This Technical Information provides reference resistance tables of abolished JPt100, JIS'89 Pt100 and JIS'91 50Ω(Pt50) for reference. 0.45 0.40 0.35 0.30 0.25 ∆t/˚C 0.20 0.15 0.10 0.05 0.00 0
50
100
150
200
250
300
350
400
450
500
550
600
650
700
t/˚C
2
TI 6B0A1-01E
1.3 Types of Resistance Thermometer Sensors The types of RTSs specified in JIS C 1604 and JIS C 1606 are standardized, as shown in Table 2, according to the standard resistance element R100/R0 value, Class, rated current, operating temperature range, and lead wire system. Table 1
Resistance Thermometer Sensors (JIS C 1604-1989, JIS C 1606-1989) Operating temperature range
Code
R100/R0 value
Class
Rated current
Lead wire system
Pt100
1.3850
Class A Class B
1mA 2mA 5mA*
L M H
-200 to 100˚ C 0 to 350˚ C 0 to 650˚ C
2-wire* 3-wire 4-wire
(JP100)
(1.3916)
Class A Class B
1mA 2mA 5mA*
L M H
-200 to 100˚ C 0 to 350˚ C 0 to 650˚ C
2-wire* 3-wire 4-wire
Note: 1. R100 is the resistance value at 100° C. 2. R0 is the resistance value of 100 Ω at of ° C. 3. An item in parentheses is discontinued. 4. Items marked with an * do not apply in Class A. 5. Sheathed RTSs operating temperature range H is 0 to +500° C. 6. The 2-wire lead wire system is not applicable to sheathed RTSs.
1.4 Tolerances vs. Temperature Tolerances with respect to temperature must be within the ranges in Table 3 throughout the operating temperature ranges. Table 4 shows samples of tolerance versus measured temperature. If the measured temperature t °C in Table 3 includes a fractional value below the decimal point, the tolerance range includes the smaller value. To avoid the risk of disputes in judgment as a result of exceeding measurement capability, the following guidelines are used for rounding off the tolerances: In Class A the number of valid significant digits below the decimal point is two, rounded down from three. In Class B the number of valid significant digits below the decimal point is one, rounded down from two. Table 2 Units:° C Class
Tolerance
Class A
± (0.15+0.002 |t|)
Class B
± (0.3+0.005 |t|)
Note 1: The error in the measured temperature of the resistance element is the measured temperature subtracted from the temperature computed from the resistance value displayed by the resistance element according to Appendix Table A1 ro Appendix Table A2. Note 2: |t| is the absolute value of the measured temperature (°C), irrespective of the + or – sign. Note 3: Although old JIS Class 0.15 has been discontinued, Yokogawa will sell it, but for the JPt100 only. Tolerance for old JIS Class 0.15 is + (0.15+0.0015 t), and applies over the temperature range of 0 to +350 °C.
TI 6B0A1-01E
3
Table 3 Units:° C Tolerance
Measured temperature
Class A
Class B
-200
±0.55
±1.3
-100
±0.35
±0.8
0
±0.15
±0.3
100
±0.35
±0.8
200
±0.55
±1.3
300
±0.75
±1.8
400
±0.95
±2.3
500
±1.15
±2.8
600
±1.35
±3.3
650
±1.45
±3.6
Note: 1. The error in the measured temperature of the resistance element is the measured temperature subtracted from the temperature computed from the resistance value displayed by the resistance element according to Appendix Table A1 ro Appendix Table A2. 2. |t| is the absolute value of the measured temperature (°C), irrespective of the + or – sign. 3. Although old JIS Class 0.15 has been discontinued, Yokogawa will sell it, but for the JPt100 only. Tolerance for old JIS Class 0.15 is + (0.15+0.0015 t), and applies over the temperature range of 0 to +350 °C.
Table 4
Temperature/Resistance Characteristics of Resistance Thermometer Sensors
Temperature (° C)
JIS'89 JPt100
JIS'89, Pt100
IEC751-1995 Pt100
-200
17.14
18.49
18.52
-100
59.57
69.25
60.26
0
100.00
100.00
100.00
100
139.16
138.50
138.51
200
177.13
175.84
175.86
300
213.93
212.02
212.05
400
249.56
247.04
247.09
500
284.02
280.90
280.98
600
317.28
313.59
313.71
700
345.13
345.28
800
375.51
375.70
Standard Resistance Table
Appandix A2, A6
Appendix A1
Appendix A4, A5
Note: IEC 751 Standard resistance table was revised in July, 1995. To conform to this change, JIS C 1604 will be revised soon.
1.5 Temperature/Resistance relationships Values in Various Nations Table 5 shows a comparison of resistance thermometer characteristics. IEC standards were standardized in Pub 751 in 1983. Due to intensifying international influence, JIS was revised to accept these in January of 1989. Note that there are significant differences between JPt100 and Pt100.
4
TI 6B0A1-01E
1.6 Copper Resistance Thermometer Sensors There are no standards for copper RTSs in JIS, and they have been little used in general industry, but they are found in rotating electrical equipment, primarily to measure temperatures of coils, bearings, etc. The following shows the nominal resistances and the standard resistance element Rt/Ro standardized in JEM 1252 (Japan Electrical Manufacturers’ Association) for RTSs in rotating electrical equipment. Table 5
Nominal Resistance
Type of resistance element Copper RTD
Table 6
TI 6B0A1-01E
Nominal resistance
Standard temperature
10Ω
25° C
25Ω
0° C
Standard Resistance Element Rt/Ro Copper Resistance Thermometer Sensors
Temperature ° C
Rt/Ro
Temperature ° C
Rt/Ro
0
1.0000
90
1.3825
10
1.0425
100
1.4250
20
1.0850
110
1.4675
25
1.1062
120
1.5100
30
1.1275
130
1.5525
40
1.1700
50
1.2125
60
1.2550
70
1.2975
80
1.3400
5
2. THERMOCOUPLES Thermocouples sense temperatures based on the principle that an electrical current is generated when two different metals are combined in a closed circuit and subjected to a temperature difference; they are widely exploited in industry due to their simple construction and excellent reliability. There are many types of thermocouples in use. Those which are the most widely used, whose characteristics are understood, and which have demonstrated their reliability, have become the objects of standardization. This document deals primarily with those thermocouples standardized in the JIS, plus other typically used thermocouples that have been field-proven in particular applications.
2.1 Overview of the JIS '95 Revisions JIS standards related to thermocouples were revised as of July 1, 1995. The major purpose of this revision is to make these JIS standards conform to the international standard IEC 584. Thermocouple codes, thermal EMF, and tolerance classes were revised to match IEC584, so JIS standard data are consistent with the standards used abroad now. The major changes are "N thermocouple is newly stipulated" and "standard thermal EMFs revised". As shown in Figure 1, the difference between JIS'89 and JIS'95 thermal EMFs will have little effect on industrial temperature measurement.
6
Figure 1
Revised Value of Thermal EMF
TI 6B0A1-01E
2.2 Types of Thermocouples In most cases, a thermocouple’s type is indicated by a code. Since the codes specified in JIS conform to the IEC standards, they are shared with other international standards, in particular with DIN (Germany) and ANSI (United States) [See Table 10]. Table 8 shows the codes, component materials, operating limits, and other features of thermocouples standardized in JIS. Table 9 shows representative non-JIS-standard-thermocouples in practical use.
TI 6B0A1-01E
7
Table 7
Code
B
R
Thermocouple Codes, Component Materials, Normal Operating Limits, and Overheat Operating Limits (JIS C 1602-1981)
Component materials
Old code
Class + side
–
Contains 30% Rhodium. PlatinumRhodium alloy
–
Contains 13% Rhodium. Platinum. Rhodium alloy
–
Contains 10% Rhodium. Platinum. Rhodium alloy
– side
Contains 6% Rhodium. PlatinumRhodium alloy
Class 2 Class 3
Platinum
Element diameter (mm)
0.50
Normal operating limits (° C)
1500
Overheat operating limits (° C)
1700
0.50
1400
1600
0.50
1400
1600
0.65
850
900
1.00
950
1000
1.60
1050
1100
2.30
1100
1150
3.20
1200
1250
0.65
650
850
1.00
750
950
1.60
850
1050
2.30
900
1100
3.20
1000
1200
Class 2 S
Alloy, primarily Nickel, Chrome, and Silicon
N
K
E
J
T
8
CA
Alloy, primarily Nickel and Chrome
Alloy, primarily CRC Nickel and Chrome
IC
CC
Iron
Copper
Platinum
Alloy, primarily Nickel, and Silicon
Alloy, primarily Nickel
Alloy, primarily Copper and Nickel
Alloy, primarily Copper and Nickel
Alloy, primarily Copper and Nickel
Class 1 Class 2 Class 3
Class 1 Class 2 Class 3
Class 1 Class 2 Class 3
Class 1 Class 2 Class 3
Class 1 Class 2 Class 3
0.65
450
500
1.00
500
550
1.60
550
650
2.30
600
750
3.20
700
800
0.65
400
500
1.00
450
550
1.60
500
650
2.30
550
750
3.20
600
750
0.32
200
250
0.65
200
250
1.00
250
300
1.60
300
350
Properties Thermal EMF is very small at room temperature. Large differences in characteristics sometimes seen. Otherwise the same as Type R. Very stable. Suitable as standard thermocouple. Suitable for corrosive environments. Sensitive to hydrogen, metal vapors. Small thermal EMF. Very slight secular change. Large extension wire error. Excellent corrosion resistance (several times that of Type K). No error generation due to short-range ordering. Magnetic field influence relatively small. Good EMF linearity. Suitable for corrosine environment. Resistant to metal vapors. Some secular change.
Lower cost than Type K, larger thermal EMF. Non-magnetic. Some drift over time.
Low cost, with fairly large thermal EMF. Good EMF linearity. Suitable for reducing environments. Large sample-to-sample variations in dharacteristics, quality. Rusts easily. Drifts at high temperatures. Low cost, with good low-temperature characteristics. Good linearity, Suitable for reducing environments. Large extension wire error.
TI 6B0A1-01E
Table 8
Non-JIS Thermocouples in practical Use
Component materials Name + side
-side
Contains 20% Rhodium. Platinum-Rhodium alloy
Contains 5% Rhodium. Platinum-Rhodium alloy
300 to 1500° C (1800° C)
Contains 40% Rhodium. Platinum-Rhodium alloy
Contains 20% Rhodium. Platinum-Rhodium alloy
1100 to 1600° C (1800° C)
Contains 5% Rhodium. Platinum-Rhodium alloy
Contains 26% Rhodium. Platinum-Rhodium alloy
Contains 3% Rhodium. Platinum-Rhodium alloy
Contains 25% Rhodium. Platinum-Rhodium alloy
Tungsten
Contains 26% Rhodium. Platinum-Rhodium alloy
Platinel
Alloy, primarily Palladium, Platium, and Gold
Alloy, primarily Gold and Palladium
Chromel/ Gold-Iron
Alloy, primarily Nickel and Chrome o4?0 (Chromel)
Contains 0.07 mole% Iron. 1 to 300K Gold-Iron alloy
PlatinumRhodium
TungstenRhenium
TI 6B0A1-01E
Operating temperature range Overheat limit in ( )
Properties
Standard thermal EMF table, and authority
Usable at high temperatures. Small thermal EMF. Appendix Table B22 Otherwise, same as Type R.
Appendix Tables B20 ASTM E988-84
0 to 2400° C (3000° C)
0 to 1100° C (1300° C)
Suitable for reducing environments, inert gasses, hydrogen gas. Fragile.
Appendix Table B22 ASTM E988-84
High resistance to abrasion. Thermal EMF nearly the same as that of Type K.
Appendix Table B22 NBS Journal of Research, vol. 68C. N08
Thermal EMF relatively large at 20 K and below. Good EMF linearity.
ASTM SPT430 Appendix Table B21
9
2.3 Thermal EMF Characteristics The standard thermal EMFs of the various thermocouple types are shown in Appendix Tables B1 through B19. Because JIS C 1602-1995 was written to be consistent with the standards used in other countries, particularly IEC, ANSI, etc., this is beneficial when importing and exporting. However, attention is required since the DIN standard adopts its own unique specifications for Type U and Type L. Table 10 gives a list of the standard thermal EMF document selections for the individual national and international standards. Equations for interpolation of standard thermal EMFs are provided for reference at the end of this document. Table 9
Thermal EMF Document Selection List Thermocouple standard dexignation
Thermocouple generic name
Standard thermal EMF document number
Standard type JIS
IEC
ANSI
Platinum-Rhodium/6-30 Platinum-Rhodium/Platinum
BS
DIN
TYPE B
Appecdix Table-B1
TYPE R
Appendix Table-B2
TYPE S
Appendix Table-B3
Nichrosil/Nisil (N)
TYPE N
Appendix Table-B4
Chromel/Alumel
TYPE K
Appendix Table-B5
Chromel-Constantan
TYPE E
Appendix Table-B6
TYPE J Iron-Constantan
–
–
Appendix Table-B7 Type L Appendix Table-B19 (Fe-CuNi)
TYPE T Copper-Constantan
Remarks
Appendix Table-B8 Type U Appendix Table-B18 (Cu-CuNi)
Note: 1. A line drawn in the table indicates that the thermocouple in question is not covered in thet standard. Those for which the same document number is given have the same standard thermal EMFs even if their names are different. 2. ASTM'93 is a national standard of the U.S. which regulates thermocouple reference thermal E.M.F.. : ASTM E230-93.
10
TI 6B0A1-01E
2.4 Tolerance Tolerances with respect to temperature are shown in Table 11: Table 10
Thermocouple Tolerances (JIS C 1602-1995)
Types
Tolerance class 1
Type B Temperature range Tolerance value Temperature range Tolerance value Type R, Type S Temperature range Tolerance value Temperature range Tolerance value
-
Tolerance class 2 600˚ C to 1700° C ±0.0025 • |t|
Tolerance class 3 600° C to 800° C +4˚ C 800° C to 1700° C ±0.005 • |t|
0˚ C to 100° C ±1° C 1100° C to 1600° C ±[1 + 0.003 (t-1100)] ° C
0° C to +600° C ±1.5° C 600˚ C to 1600° C ±0.0025 • |t|
Type K, Type N Temperature range Tolerance value Temperature range Tolerance value
-40° C to 375° C ±1.5° C 375° C to 1000° C ±0.004 • |t|
-40° C to +333° C ±2.5° C 333° C to 1200° C ±0.0075 • |t|
-167° C to +40° C ±2.5˚ C -200° C to -167° C ±0.015 • |t|
Type E Temperature range Tolerance value Temperature range Tolerance value
-40° C to +375° C ±1.5° C 375° C to 800° C ±0.004 • |t|
-40° C to +333° C ±2.5° C 333° C to 900° C ±0.0075 • |t|
-167° C to +40° C ±2.5° C -200° C to -167° C ±0.015 • |t|
Type J Temperature range Tolerance value Temperature range Tolerance value
-40° C to +375° C ±1.5° C 375° C to 750° C ±0.004 • |t|
-40° C to +333° C ±2.5° C 333° C to 750° C ±0.0075 • |t|
Type T Temperature range Tolerance value Temperature range Tolerance value
-40° C to +125° C ±0.5° C 125° C to 350° C ±0.004 • |t|
-40° C to +133° C ±1° C 133° C to 350° C ±0.0075 • |t|
-
-67° C to +40° C ±1° C -200° C to -67° C ±0.015 • |t|
Note: 1. Thermocouple materials are noemally supplied to meet the manufacturing tolerances specified in the table for temperatures above -40˚ C. These materials, however, may not fall within the manufacturing tolerances for low temperatures given under class 3 for types T, E, K and N. If thermocouples are required for meet limits of class 3, as well as those of class 1 or 2 the purchaser shall state this, as selection of materials is usually required.
2.5 Themocouple Electrical Characteristics Electrical characteristics is as shown in Table 12. Insulation resistance is applied to routine unit test. Dielectric strength is applied to type test. Table 11
Electrical Characteristics Item
TI 6B0A1-01E
Characteristics
Insulation resistance (Only applied to thermocouples with protection tube)
Insulation resistance between terminals and protection tube is more than 10MW/500VDC
Dielectric strength (Only applied to thermocouples with protection tube)
500VAC for one minute
11
2.6 Thermocouple operating Limits Normal operating limits are the temperatures that are generally recommended for continuous use in air. Overheat operating limits are the temperatures for short-period use not sharply defined limiting temperatures, but rather those at which operations for the times indicated in Table 13 will not result in thermal EMF changes greater than the values also shown in that table for continuous operation in clean air. Table 12
Thermocouple Continuous-Operation Times Continuous-operation time(h)
12
Code
At normal operating limit
At overheat operating
Thermal EMF change(%) at any temperaturelimit
B R S N K E J T
2000 2000 2000 10000 10000 10000 10000 10000
50 50 50 250 250 250 250 250
±0.5 ±0.5 ±0.5 ±0.75 ±0.75 ±0.75 ±0.75 ±0.75
TI 6B0A1-01E
2.7 Thermocouple Leadwire Resistances Although electronic instruments almost unaffected by thermocouple leadwire resistance, it can cause problems in the case of moving coil instruments and may require compensation, so the user should follow any directions given in the manual for the instrument. Table 14 shows thermocouple resistance R0 at 0˚C, and resistance R20 at 20˚C. Table 15 shows the resistance ratios Rt/R20 and Rt/R0, between resistance values R20 and R0 and resistance value Rt at t˚C. When compensating for this resistance with moving-coil instruments, it is customary to treat half of the thermocouple’s specified length as being at the operating temperature, and the other half as the room temperature. Table 13
Thermocouple Resistances Unit: Ω/m
Code for component materials Old code (reference) Wire diameter in mm 0.32 0.50 0.65 1.00 1.60 2.30 3.20
Table 14
B
R
S
K
E
J
T
N
-
-
-
CA
CRC
IC
CC
-
1.75 -
1.47 -
1.43 -
2.95 1.25 0.49 0.24 0.12
3.56 1.50 0.59 0.28 0.15
1.70 0.72 0.28 0.14 0.07
6.17 1.50 0.63 0.25 -
3.94 1.66 0.65 0.31 0.16
J IC
T CC
N –
Thermocouple Resistance Ratios (Rt/R0 and Rt/R20)
Code Old code Temperature (t) ˚C 0 20 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700
TI 6B0A1-01E
B
R –
S –
K CA
E CRC
Rt/R0 Rt/R20 Rt/R0 Rt/R20 Rt/R0 Rt/R20 Rt/R0 Rt/R20 Rt/R0 Rt/R20 Rt/R0 Rt/R20 Rt/R0 Rt/R20
Rt/R0
1.00 1.03 1.17 1.34 1.50 1.65 1.80 1.95 2.10 2.25 2.39 2.53 2.66 2.79 2.92 3.04 3.16 3.28 3.40
1.00 1.02 1.15
0.97 1.00 1.13 1.29 1.45 1.60 1.74 1.88 2.03 2.17 2.31 2.45 2.57 2.70 2.82 2.94 3.06 3.17 3.29
1.00 1.05 1.24 1.46 1.68 1.94 2.12 2.32 2.52 2.72 2.90 3.04 3.26 3.43 3.59 3.75 3.90
0.95 1.00 1.17 1.40 1.61 1.85 2.02 2.22 2.41 2.60 2.78 2.95 3.12 3.28 3.44 3.59 3.73
1.00 1.05 1.25 1.48 1.71 1.97 2.16 2.37 2.58 2.75 2.97 3.16 3.34 3.52 3.68 3.85 4.00
0.95 1.00 1.17 1.39 1.61 1.83 2.03 2.23 2.43 2.61 2.80 2.97 3.14 3.30 3.46 3.62 3.77
1.00 1.02 1.10 1.18 1.26 1.32 1.37 1.41 1.45 1.50 1.54 1.59 1.64 1.68
0.98 1.00 1.08 1.16 1.23 1.29 1.34 1.38 1.42 1.47 1.51 1.56 1.61 1.65
1.00 1.01 1.02 1.05 1.08 1.11 1.13 1.16 1.18 1.20
1.00 1.00 1.02 1.05 1.08 1.11 1.13 1.15 1.18 1.20
1.00 1.02 1.10 1.22 1.34 1.55 1.78 2.04 2.35 2.69
0.98 1.00 1.08 1.19 1.34 1.52 1.74 2.00 2.30 2.44
1.00 1.00 1.01 1.02 1.03
1.00 1.00 1.01 1.02 1.03
13
3. MINERAL INSULATED THERMOCOUPLES 3.1 Construction Mineral Insulated thermocouples are filled with a powdered inorganic insulator (Mgo) between the metal sheath and the thermocouple element, and are of a single construction. Table 16 shoes the dimensions of Mineral Insulated thermocouples. Table 15
Mineral Insulated Thermocouple Dimensions Unit: mm
Metal sheath outer diameter D 1.0 ± 0.05 1.6 ± 0.05 3.2 ± 0.05 4.8 ± 0.05 6.4 ± 0.05 8.0 ± 0.05
Figure 2
Thermocouple element diameter d
15% or more of metal sheath outer diameter
14
10% or more of metal sheath outer diameter
Cross Section of Mineral Insulated Themocouple
(1) Longitudinal section of the measuring junction of an earthed thermocouple
Figure 3
Metal sheath thickness t
(2) Longitudinal section of the measuring junction of an insulated thermocouple
Constructions of Measuring Junctions
TI 6B0A1-01E
3.2 Tolerances Table 16 shows tolerances. These are determined in conformance with those for general thermocouples. Table 16
Tolerance classes for thermocouples (reference junction at 0˚C) Type
Tolerance class 1
Tolerance class 2
Tolerance class 3
Type T Temperature range Tolerance value Temperature range Tolerance value
-40° C to +25° C ±0.5° C 125° C to 350° C ±0.004 • |t|
-40° C to +133° C ±1° C 133° C to 350° C ±0.0075 • |t|
-67° C to +40° C ±1° C 200° C to -67° C ±0.015 • |t|
Type E Temperature range Tolerance value Temperature range Tolerance value
-40° C to +375° C ±1.5° C 375° C to 800° C ±0.004 • |t|
-40° C to +333° C ±2.5° C 333° C to 900° C ±0.0075 • |t|
-167° C to +40° C ±2.5° C -200° C to -167° C ±0.015 • |t|
Type J Temperature range Tolerance value Temperature range Tolerance value
-40° C to +375° C ±1.5° C 375° C to 750° C ±0.004 • |t|
-40° C to +333° C ±2.5° C 333° C to 750° C ±0.0075 • |t|
Type K, Type N Temperature range Tolerance value Temperature range Tolerance value
-40° C to +375° C ±1.5° C 375° C to 1000° C ±0.004 • |t|
-40° C to +333° C ±2.5° C 333° C to 1200° C ±0.0075 • |t|
– – – – -167° C to +40° C ±2.5° C -200° C to -167° C ±0.015 • |t|
Note: (1) The tolerance is the maximum limit for the difference calculated by subtracting the measurement junction temperature from the temperature converted from the thermal EMF using the standard thermal EMF table. The tolerance is the larger of ° C or % (2) Thermocouple materials are noemally supplied to meet the manufacturing tolerances specified in the table for temperatures above -40° C. These materials, however, may not fall within the manufacturing tolerances for low temperatures given under class 3 for types T, E, K and N. If thermocouples are required for meet limits of class 3, as well as those of class 1 or 2 the purchaser shall state this, as selection of materials is usually required.
TI 6B0A1-01E
15
3.3 Codes and Normal Operating Limits The code for a Mineral Insulated thermocouple is the same as that for a regular thermocouple with an S added at the beginning . Table 14 shows the normal operating limits for Mineral Insulated thermocouples. The codes for the materials used for the sheath are as follows: A : Austenitic stainless steel (SUS 347, SU S316) B : Nickel-Chromium heat-resistant alloy (Inconel) Table 17
Code SN
Normal Operating Limits for Mineral Insulated Thermocouples (JIS C 16051995) Sheath Outer Diameter mm
Metal Sheath ° C A
0.5
600
1.0, 1.5, (1.6), 2.0
650
3.0, (3.2)
SK
750
4.5, (4.8)
800
4.5, (4.8)
800
900
6.0, (6.4)
800
1000
8.0
900
1050
0.5
600 650 750
4.5, (4.8)
800
900
6.0, (6.4)
800
1000
8.0
900
1050
0.5
600
1.0, 1.5, (1.6), 2.0
650
3.0, (3.2)
SJ
ST
900
1.0, 1.5, (1.6), 2.0 3.0, (3.2)
SE
B
750
4.5, (4.8)
800
900
6.0, (6.4)
800
900
8.0
800
900
0.5
400
1.0, 1.5, (1.6), 2.0
450
3.0, (3.2)
650
4.5, (4.8)
750
6.0, (6.4)
750
8.0
750
0.5
300
1.0, 1.5, (1.6), 2.0
300
3.0, (3.2)
350
4.5, (4.8)
350
6.0, (6.4)
350
8.0
350
Notes: 1. The normal operating limit is the temperature at which the device can be used continuously in air. 2. The normal operating limits differ from those in JIS C 1602 due to the large dependence on the heatresistance of the metal sheath. 3. ( ) will be removed in the future.
16
TI 6B0A1-01E
3.4 Electrical Characteristics (Insulation Resistance, Thermocouple Leadwire Resistance) Insulation resistances and thermocouple leadwire resistances are as shown in Table 19. Table 20 shows sheathed thermocouple leadwire resistances. Due to the large variations in sheathed thermocouple leadwire resistances, no standards are prescribed. Table 20 presents some examples for reference: Table 18
Electrical Characteristics Metal Sheath Outer Diameter (mm)
Item Insulation resistance
0.5, 1.0, 1.5, (1.6), 2.0
Characteristics >20MΩ /100VDC
3.0,(3.2), 4.5, (4.8), 6.0, >100MΩ /500VDC (6.4), 8.0 Dielectric strength
1.0, 1.5, (1.6)
100VAC for one minute
3.0, (3.2), 4.5, (4.8), 6.0, 500VAC for one minute (6.4), 8.0 Notes: (1) These tests should not be applied to earthed thermocouples. (2) For thermocouples with compensating cable, apply the smaller of the above values or insulation resistances regulated in JIS C 1610. (3) ( ) will be removed in the future.
Table 19 Sheath Outer diameter (mm)
Mineral insulated Thermocouple Leadwire Resistances SK Standard resistance
SJ
Maximum Standard resistance resistance
Unit: Ω/m
ST Maximum Standard resistance resistance
SE
Maximum Standard resistance resistance
Maximum resistance
219.49
–
–
–
–
–
–
–
1.0
40.32
55.22
23.81
32.44
–
–
–
–
1.6
16.34
19.75
9.65
11.65
7.94
9.61
–
–
3.2
3.15
3.74
1.87
2.2
1.61
1.90
3.77
4.46
4.8
1.40
1.50
0.84
0.93
0.70
0.78
1.70
1.80
6.4
0.79
0.89
0.48
0.54
0.40
0.45
0.94
1.10
8.0
0.66
0.73
0.38
0.44
0.32
0.37
0.77
0.87
2.2
16.31
19.8
–
–
–
–
–
–
3.2
7.72
8.79
4.60
5.20
3.80
4.40
–
–
4.8
3.43
4.08
2.10
2.50
1.70
2.10
–
–
6.4
1.93
2.20
1.20
1.30
0.94
1.10
–
–
8.0
1.24
1.44
0.75
0.82
1.63
0.69
1.48
1.73
Note: Resistance dispersion is ±20%
TI 6B0A1-01E
17
4. EXTENTION AND COMPENSATING CABLE Table 21 shows the types (codes), component materials, operating temperatures, tolerances and colors for compensating cable. In the revision of JIS C1610 (Compensating cable) of July 1995, types (codes), operating temperatures, tolerances, and colors were changed. Especially for the color of the cable cover, Division 1 is newly added to conform to IEC standard. However, the former JIS color regulation still remains as Division 2 so as not to cause accidents due to the color change when expanding or retrofitting existing systems. Use Division 2 as necessary. Usage classification is shown in Table 22. Since operating temperature high limit extended to 200˚C, FEP (teflon) is newly added to insulator types. As usage classification is determined by insulator material, conditions are described in the notes of Table 22. Table 23 shows insulator resistance. Standard values differ according to the materials. Table 20
Compensating Cable Characteristics
Types of TC combined
Compensating Cable Types
Code
Code
Old Code
+ side
- side
B
BC
BX
Copper
Copper
Copper
Alloy, primarily 0 to 100 Copper and 0 to 100 Nickel
R
RCA
RX
Component Materials
RCB
Temp. range Tolerance (for tolerance) (µV) (° C)
Surface Color Code
Class 1
Class 2
Div. 1
Div. 2
–
–
Gray
Gray
–
⫾30
Orange
Black
–
⫾60
0 to 100
–
⫾30
Orange
Black
0 to 200
Pink
–
Green
Blue
0 to 100
S
SCA
–
⫾60
N
NX
–
Alloy, primarily Alloy, primarily – 25 to 200 Nickel and Nickel and Chrome Silicon
⫾60
⫾100
NC
–
Alloy, primarily Alloy, primarily 0 to 150 Copper and Copper and Nickel Nickel
–
⫾100
KX
KX
⫾60
⫾100
KCA
–
– 25 to 200 Alloy, primarily Alloy, primarily Nickel and Nickel Chrome 0 to 150
–
⫾100
KCB
WX
Icon
Alloy, primarily 0 to 150 Copper and Nickel
–
⫾100
KCC
VX
Copper
Alloy, primarily 0 to 100 Copper and Nickel
–
⫾100
E
EX
EX
Alloy, primarily Alloy, primarily – 25 to 200 Nickel and Copper and Chrome Nickel
⫾120
⫾200
Purple
Purple
J
JX
JX
Iron
Alloy, primarily – 25 to 200 Copper and Nickel
⫾85
⫾140
Black
Yellow
T
TX
TX
Copper
Alloy, primarily – 25 to 100 Copper and Nickel
⫾30
⫾60
Brown
Brown
SX
SCB
K
Note: The temperature at the reference-junction compensation point should be within the tolerance of conductors, and as for cable operating temperature range, table 22 usage classification is given a higher priority.
18
TI 6B0A1-01E
Table 21
Usage Classification Unit: ° C
Usage Classfication
Code
Old Code
Materials of Insulator
Operating Temperature
General use
G
G
Vinyl
-20 to +90
1) Not applicable for RCB and SCB 2) Operating temperature range of BC, RCA, SCA, NC, KCA, LCB KCC is from 0° C to +90° C
Middle range
H
H
Glass yarn
0 to +150
Not applicable for BC, RCA, SCA, KCC or TX.
High range
S
–
FEP
-25 to +200
1) Not applicable for compensating conductors. 2) Operating temperature range of TX is from -25° C to +100° C
Table22
Notes
Insulator Resistance Unit: MΩ • km
Usage Classfication
Codes
Insulation Resistance
General use
G
Vinyl
50
Middle range
H
Glassyarn
0.05
High range
S
FEP
1000
Table 23
Extension and Compensating Cable Resistance
Extention cable Copper (BC both sides/ RC, SC, KCC, TX + side) Iron (KCB, JX + side)
Electrical resistance of twisted Electrical resistance (leadwire diameter, 0.65mmat conductors at 20° C Ω /km 20° C, Ω /km) 7 wires 4 wires 55.29 448.0
Copper-Nickel alloy (RC, SC-side)
204.0
Alumel (KX – side)
882.0
Chromel (KX + side)
2141
Copper-Nickel alloy (JX-side)
1597
Chromel (EX + side)
TI 6B0A1-01E
Materials of Insulator
882.0
7.90 65.92 30.02
14.24 115.4 52.53
126.0
220.5
305.8
535.2
233.5
411.2
126.0
220.5
Copper-Nickel alloy (EX-side)
1597
233.5
411.2
Copper-Nickel alloy (TX-side)
1597
233.5
411.2
Copper-Nickel alloy (KCC-side)
1597
233.5
411.2
19
5. INTERNATIONAL TEMPERATURE SCALE 5.1 International Temperature Scale Plan As with other physical quantities, because temperatures must be expressed the same internationally, they are expressed with a temperature scale based on a resolution passed at a general meeting of the International Weights and Measures Committee. The old international temperature scale, the 1968 International Practical Temperatures Scale (IPTS-68), was revised by the 78th International Weights and Measures Commuitee in September of 1989 based on a resolution from the 18th general meeting of the International Weights and Measures Committee which met in 1987. The 1990 International Temperature Scale (ITS-90) was adopted as the new international temperature scale, and has been in effect internationally since January 1,1990. These changes in the international temperature scale solved problems found in IPTS-68 through advances in measurement technology centering on the latest thermodynamic temperature measurements. The international temperature scale plan is guided by the following three principles: (1) The plan specifies repeatable thermal equilibrium states, which are assigned temperatures to define fixed points. (2) The plan assigns a standard thermometer for each temperature range, calibrated to the defining fixed points. (3) The plan establishes interpolation formulas that decide the relationships between temperatures (international temperatures) and standard thermometer indicated temperatures (output values) in order to interpolate between the defining fixed points. Although the temperature concepts are based on thermodynamic temperatures, since absolute measurement of thermodynamic temperatures is not possible, improvements that bring the international temperature scale closer to thermodynamic temperatures are a matter of repetition along with progress in measurement techniques. Gas and radiation thermometers are used as thermodynamically well-defined thermometers in the measurement of thermodynamic temperatures. However, although a gas thermometer in principle determines thermodynamic temperature from a comparison of pressure at ideal states using ideal gasses, in fact since no ideal gas actually exists and an ideal state cannot be perfectly attained, we can only arrange conditions close to the ideal and add corrections to the best of our ability to determine the true values. Thus, in keeping with progress in measurement techniques, corrections are incorporated into the temperatures of the defining fixed points. Previously, a new international temperature scale had been adopted roughly every twenty years. The ITS-90 now in use has been adopted as an attempt to faithfully arrive at the thermodynamic temperatures using state-of-the-art techniques. However, because advanced techniques were required to achieve ITS-90, these endeavors are entrusted to the techniques of specialists at organizations studying temperature measurements.
20
TI 6B0A1-01E
5.2 Essentials of the 1990 International Temperature Scale (ITS-90) ITS-90 is intended to solve certain problems found in the 1968 International Practical Temperature Scale (IPTS-68). The main corrections are as follows: (1) The low temperature range is expanded, and is defined to 0.65K. (2) The range previously defined by thermocouples (630.74 to 1064.43˚C) is replaced by a range up to 961.78˚C defined using a platinum resistance thermometer, while the range above 961.78˚C is defined using a radiation thermometer. (3) The defining fixed points have been changed, with the boiling points of oxygen, water, and neon being eliminated and replaced by several triple points and freezing points, and the temperatures at the defining fixed points overall have been changed. The relationship between the defining fixed points of the ITS-90 and the instruments for interpolation is shown in Table 25. Because the temperatures for the defining fixed points have changed overall, the t90-t68 Temperature Difference shown in Table 26 has been changed based on these definition changes Table 24
Comparison of IPTS-68 and ITS-90
Interpolation instruments
T68/K
T90/K
t90/˚C
Interpolation instruments
0.65 Helium vapor pressure scale He (V)
3 to 5
e - H2 (T) (B)e - H2 (V) (B)e - H2 (V) Ne (T) Ne (B) O2 (T) Ar (T) O2 (C) Hg (T) H2O (T) Ga (M) H2O (V) In (F) Sn (F) Zn (F) Al (F)
13.8033 to 17 to 20.3 24.5561
-248.5939
54.3584 83.8058
-218.7916 -189.3442
234.3156 273.16 302.9146
-38.8344 0.01 29.7646
429.7485 505.078 692.677 933.473
156.5985 231.928 419.527 660.323
1234.93 1337.33 1357.77
961.78 1064.18 1084.62
Gas thermometer 13.81 17.042 20.28 27.102 54.361 83.798 90.188 Platinum resistance thermometer 273.16 373.15 505.1181 692.73
S thermocouple Plank's law of radiation
903.9 1235.58 1337.58
Ag (F) Au (f) Cu (F)
-29.3467
Platinum resistance thermometer
Plank's law of radiation
Note: Descriptions of defining fixed-point states: B: Boiling point (state of equilibrium between the liquid phase and gas phase at one atmosphere of pressure) C: Condensation point (state of equilibrium between the liquid phase and gas phase at one atmosphere of pressure at which the liquid phase condenses) F: Freezing point (state of equilibrium between the liquid phase and solid phase) M: Melting point (state of equilibrium between the solid phase liquid phase) T: Triple point (state of equilibrium between the solid phase, liquid phase, and gas phase) V: Vapor pressure point (state of equilibrium between the liquid phase and gas phase)
TI 6B0A1-01E
21
5.3 Influence of ITS-90 on Industrial Thermometers Because industrial thermometers conform to JIS, the temperature differences due to definition changes, and their relationship to JIS, are matters of importance. Since the temperature differences accompanying definition changes are small, on a practical level their influence can be ignored (see Figure 4). The areas where the effects of ITS-90 become a problem for the temperature related JIS standards are in the standard thermal EMF tables for thermocouples, and the standard resistance are in the standard thermal EMF tables for thermocouples, and the standard resistance tables for resistance thermometers sensors. Because the temperatures for the current standard tables are regulated by IPTS-68, the switch to ITS-90 requres that these be changed by the temperature difference (t90 - t68). Because the JIS tolerances for temperature sensors are specified with respect to the standard tables, the influence of ITS-90 becomes clear when the temperature differences due to definition changes are compared to the tolerances. The maximum temperature difference due to a definition change in the region up to 1100˚C is + 0.36˚C at 780˚C. The value of this corresponds to 11% of the tolerance (3.1˚C) of a Class 0.4 thermocouple, and can, in practice, be ignored. Although for a Class 0.25 thermocouple the change at 780˚C reaches nearly half of the tolerance, this presents no problems because Class 0.25 applies only to Types R and S thermocouples, and these are usually used at 1000˚C and above. The operating limits for RTSs are 650˚C for Pt100, and 500˚C for JPt100. The largest change in the range up to 650˚C is 0.115˚C at 600˚C; this value is 10% of the tolerance of + 1.35˚C for a Class A type, and can be ignored in practice.
accuracy ˚C
Although as explained above there is no problem in viewing the transition to ITS-90 as having no practical effect on industrial thermometry, there are instances in which the application of ITS-90 required for precision measurements such as temperature measurement in scientific research for determining physical constants. In such cases, temperature measurements should be converted according to the values in Table 26.
Figure 4
22
Temperature Difference in International Temperature Scales, and JIS Tolerances
TI 6B0A1-01E
Table 25
TI 6B0A1-01E
Differences Between ITS-90 and IPTS-68
23
APPENDIX TABLE A1-1 PT100 REFERENCE RESISTANCE TABLE This table shows values specified by JIS C 1604-1989 and JIS C1606-1989. ■ Pt100 Resistance thermometer sensor (JIS C1604-1989) (JIS C1606-1989)
24
TI 6B0A1-01E
APPENDIX TABLE A1-2 PT100 REFERENCE RESISTANCES
The reference resistances in Appendix Table A1 are calculated in the following equations: -200˚C to 0˚C range: Rt = R0 [1 + At + Bt2 + C (t - 100) t3] 0˚C to + 650 ˚C range: Rt =R0 (1 + At + Bt2) Where: A = 3.90802 x 10-3˚C -01 B = -5.802 x 10 - 7˚C - 2 C = -4.2735 x 10 - 12˚C - 4 Notes: 1. R0 is 100Ω, and Rt represents the resistance at t˚C. 2. The above expressions were used to calculate the reference resistances for this standard, and are not intended to be used to determine the characteristics of any individual RTS.
TI 6B0A1-01E
25
APPENDIX TABLE A2-1 JPT100 REFERENCE RESISTANCE TABLE This is the JPt100 reference resistance table defined in JISC1604 and JISC1606. ■ JPt 100RTS (JISC1604-1989) (JISC1606-1989)
26
TI 6B0A1-01E
APPENDIX TABLE A2-2 JPT100 REFERENCE RESISTANCE TABLE ■ JPT100RTS continued from the previous page.
TI 6B0A1-01E
27
APPENDIX TABLE A3-1 RT50 REFERENCE RESISTANCE TABLE Abolished after January 1, 1989. ■ Pt 50 Ω RTS.
28
TI 6B0A1-01E
APPENDIX TABLE A3-2 PT50 REFERENCE RESISTANCE TABLE Abolished after January 1, 1989. ■ Pt 50 Ω (Continued from the previous page)
TI 6B0A1-01E
29
APPENDIX TABLE A4-1 PT100 REFERENCE RESISTANCE TABLE This is the reference resistance table defined in IEC Pub 751-1995. JIS C 1604-1997.
30
TI 6B0A1-01E
APPENDIX TABLE A4-2 PT100 REFERENCE RESISTANCE TABLE
TI 6B0A1-01E
31
APPENDIX TABLE A5 INTERPOLATION EQUATION FOR PT100 REFERENCE RESISTANCE The reference resistances in Appendix A4 Pt100 reference resistance table (IEC 7511995) are calculated in the following equations; -200˚C to 0˚C range: Rt = Ro [1 + At + Bt2 + C(t - 100)t3] 0˚C to 850˚C range: Rt = Ro (1 + At + Bt2) Where; A = 3.9083 x 10-3˚C-1 B = -5.775 x 10-7˚C-2 C = -4.183 x 10-12˚C-4 Notes: 1. Ro is 100Ω, and Rt represents the resistance at t˚C. 2. The above expressions were used to calculate the reference resistances for this standard, and are not intended to be used to determine the characteristics of any individual RTS.
APPENDIX TABLE A6
INTERPOLATION EQUATION FOR JPT100 REFERENCE RESISTANCE
The reference resistances in Appendix A2 JPt100 reference resistance table (JIS C 1604-1989) are calculated in the following equations: For 0°C to 630°C range, Rt = Ro (1 + At1 + Bt12) Where; A = 0.3974973 x 10-2 B = -0.58973 x 10-6 t' is obtained in equation (2) t' = t - 0.045 ( t' ) ( t' - 1) ( t' - 1) ( t' - 1) 100 100 419.58 630.74
(1)
(2)
For -200°C to 0°C range, =7 ∑ ai ti i=0 i
Rt = Ro
(3)
Where; a0 = 0 a1 = 3.971686 x 10-3 a2 = -1.157433 x 10-6 a3 = -2.051844 x 10-8 a4 = -3.629438 x 10-10 a5 = -3.157615 x 10-12 a6 = -1.369914 x 10-14 a7 = -2.303654 x 10-17 Notes: 1. R0 is 100Ω, and Rt represents the resistance at t°C. 2. The tolerance of calculation error in the equation (2) is less than 0.000019°C. 3. The tolerance of calculation error in the equation (3) is less than 0.0035°C.
32
TI 6B0A1-01E
APPENDIX TABLE B1-1 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
TI 6B0A1-01E
33
C 1602-1995
APPENDIX TABLE B1-2 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE
34
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B1-3 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
35
C 1602-1995
APPENDIX TABLE B1-4 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C
36
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B2-1 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995
TI 6B0A1-01E
37
C 1602-1995
APPENDIX TABLE B2-2 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE
38
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B2-3 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
39
C 1602-1995
APPENDIX TABLE B2-4 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at reference-junction compensation point is set at 0˚C.
40
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B3-1 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
TI 6B0A1-01E
41
C 1602-1995
APPENDIX TABLE B3-2 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE
42
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B3-3 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
43
C 1602-1995
APPENDIX TABLE B3-4 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
44
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B4-1 TYPE N THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
TI 6B0A1-01E
45
C 1602-1995
APPENDIX TABLE B4-2 TYPE N THERMOCOUPLE THERMAL E.M.F. TABLE
46
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B4-3 TYPE N THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C. TI 6B0A1-01E
47
C 1602-1995
APPENDIX TABLE B5-1 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
48
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B5-2 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
49
C 1602-1995
APPENDIX TABLE B5-3 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE
50
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B5-4 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
51
C 1602-1995
APPENDIX TABLE B6-1 TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
52
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B6-2 TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
53
C 1602-1995
APPENDIX TABLE B6-3 TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
54
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B7-1 TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
TI 6B0A1-01E
55
C 1602-1995
APPENDIX TABLE B7-2 TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE
56
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B7-3 TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
57
C 1602-1995
APPENDIX TABLE B8-1 TYPE T THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JIS C1602-1995.
58
TI 6B0A1-01E
C 1602-1995
APPENDIX TABLE B8-2 TYPE T THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
59
C 1602-1995
APPENDIX TABLE B9
INTERPOLATION EQUATION OF REFERENCE THERMAL E.M.F. of JIS'95 (JIS C1602-1995)
These equations are applied to Appendix Tables B1 to B8. E: Reference thermal e.m.f. t: Temperature (˚C)
Remarks: This table is applied to calculate Appendix table B1 type B thermocouple thermal e.m.f..
60
TI 6B0A1-01E
C 1602-1995
Remarks: This table is applied to calculate Appendix table B2 type R thermocouple thermal e.m.f..
TI 6B0A1-01E
61
C 1602-1995
Remarks: This table is applied to calculate Appendix table B3 type S thermocouple thermal e.m.f..
62
TI 6B0A1-01E
C 1602-1995
Remarks: This table is applied to calculate Appendix table B4 type N thermocouple thermal e.m.f..
TI 6B0A1-01E
63
C 1602-1995
Remarks: This table is applied to calculate Appendix table B5 type K thermocouple thermal e.m.f..
64
TI 6B0A1-01E
C 1602-1995
Remarks: This table is applied to calculate Appendix table B6 type E thermocouple thermal e.m.f..
TI 6B0A1-01E
65
C 1602-1995
Remarks: This table is applied to calculate Appendix table B7 type J thermocouple thermal e.m.f..
66
TI 6B0A1-01E
C 1602-1995
Remarks: This table is applied to calculate Appendix table B8 type T thermocouple thermal e.m.f..
TI 6B0A1-01E
67
APPENDIX TABLE B10-1 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981.
68
TI 6B0A1-01E
APPENDIX TABLE B10-2 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
69
APPENDIX TABLE B10-3 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE
70
TI 6B0A1-01E
APPENDIX TABLE B10-4 TYPE B THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
71
APPENDIX TABLE B11-1 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981.
72
TI 6B0A1-01E
APPENDIX TABLE B11-2 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
73
APPENDIX TABLE B11-3 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE
74
TI 6B0A1-01E
APPENDIX TABLE B11-4 TYPE R THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
75
APPENDIX TABLE B12-1 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981.
76
TI 6B0A1-01E
APPENDIX TABLE B12-2 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
77
APPENDIX TABLE B12-3 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE
78
TI 6B0A1-01E
APPENDIX TABLE B12-4 TYPE S THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
79
APPENDIX TABLE B13-1 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981 (Type K) JISC16051982 (Type SK).
80
TI 6B0A1-01E
APPENDIX TABLE B13-2 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
81
APPENDIX TABLE B13-3 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE
82
TI 6B0A1-01E
APPENDIX TABLE B13-4 TYPE K THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
83
APPENDIX TABLE B14-1 TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981 (Type E) and JISC1605-1982 (Type SE).
84
TI 6B0A1-01E
APPENDIX TABLE B14-2 TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE
TI 6B0A1-01E
85
APPENDIX TABLE B14-3 TYPE E THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
86
TI 6B0A1-01E
APPENDIX TABLE B15-1 TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981 (Type J) and JISC1605-1982 (Type SJ).
TI 6B0A1-01E
87
APPENDIX TABLE B15-2 TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE
88
TI 6B0A1-01E
APPENDIX TABLE B15-3 TYPE J THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
89
APPENDIX TABLE B16-1 TYPE T THERMOCOUPLE THERMAL E.M.F. TABLE This is the reference thermal e.m.f. table defined in JISC1602-1981 (Type T) and JISC1605-1982 (Type ST).
90
TI 6B0A1-01E
APPENDIX TABLE B16-2 TYPE T THERMOCOUPLE THERMAL E.M.F. TABLE
Remarks: The temperature at the reference-junction compensation point is set at 0˚C.
TI 6B0A1-01E
91
APPENDIX TABLE B17.
INTERPOLATION EQUATION OF REFERENCE THERMAL E.M.F. of JIS'81 (JIS C1602-1981, abolished after July 1995)
These equations are applied to Appendix Table B10 to 16. E: Reference thermal e.m.f t: Temperature (˚C)
92
TI 6B0A1-01E
TI 6B0A1-01E
93
94
TI 6B0A1-01E
TI 6B0A1-01E
95
APPENDIX TABLE B18-1 Cu-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE U)
96
TI 6B0A1-01E
APPENDIX TABLE B18-2 Cu-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE U)
TI 6B0A1-01E
97
APPENDIX TABLE B19-1 Fe-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE L)
98
TI 6B0A1-01E
APPENDIX TABLE B19-2 Fe-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE L)
TI 6B0A1-01E
99
APPENDIX TABLE B19-3 Fe-CuNi THERMOCOUPLE THERMAL E.M.F. TABLE (DIN 43710 TYPE L)
100
TI 6B0A1-01E
APPENDIX TABLE B20-1 W (W5Re/W26Re) THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE (ASTM E988)
TI 6B0A1-01E
101
APPENDIX TABLE B20-2 W (W5Re/W26Re) THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE (ASTM E988)
102
TI 6B0A1-01E
APPENDIX TABLE B20-3 W (W5Re/W26Re) THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE (ASTM E988)
TI 6B0A1-01E
103
APPENDIX TABLE B20-4 W (W5Re/W26Re) THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE (ASTM E988)
104
TI 6B0A1-01E
APPENDIX TABLE B21
TI 6B0A1-01E
KP/Au•Fe THERMOCOUPLE REFERENCE THERMAL E.M.F. TABLE
105
APPENDIX TABLE B22
106
TABLE OF THERMOCOUPLE REFERENCE THERMAL E.M.F. PRACTICED IN TABLES OTHER THAN THOSE DEFINED IN JIS.
Subject to change without notice. Printed in Japan, 703/b(YG)
TI 6B0A1-01E