www.rollease.com. RollEase West. 7150 West Roosevelt Street, Suite-A-155.
Phoenix, AZ 85043 USA. Office: 623.936.5818 Fax: 623.936.5294. RollEase ...
RollEase Link System Roller Shade Fabrication Instructions A
The RollEase Link System is designed so that up to three shades may be operated simultaneously using one control mechanism. The control mechanism must be properly sized to the total weight of all linked shades. Weight capacity of the system is 40 lbs (18,14 kgs) for the total combined weight of all shades used with the system. To minimize light gap deductions for each shade, individual component measurements are listed in the chart below.
A
INSIDE MOUNT
or
OUTSIDE MOUNT
Measure inside the frame.
Measure across from first bracket to last bracket.
www.AV-Outlet.com
1. CALCULATE THE EXACT WIDTH OF THE COMBINED SHADES Two Shades Use the formula: Cut width = A - (K + 1/2 L) - (1/2 L + P) Shade C1, deduct the the amount of space taken up by the clutch (K) and 1/2 (L) the distance taken up the Link bracket. Shade C2, deduct 1/2 (L) and the space taken up by the Pin End (P) ----------------------------------------------------------------------------------------------------------Three Shades Use the formula: Cut width = A - (K + 1/2 L) - (1/2 L + 1/2 L) - (1/2 L + P) Shade C1: deduct the the amount of space taken up by the clutch (K) and 1/2 (L) the distance taken up the Link bracket. Shade C2: deduct 1/2 (L) twice; once for each end of the center shade Shade C3: deduct 1/2 (L) the space taken up by the Pin End (P).
A
C2
C1
C = A - (K + 1/2 L) - (1/2 L + P)
For simplification one may elect to take the largest deduction for that clutch type (see “ONE CUT” in chart ) and make equal deductions for all shades being linked.
A
The differences between the smallest possible deduction for one shade versus the largest required is often smaller than a fabricators ability to accurately cut tube and shade cloth. Exact deductions for specific shade position is provided for those fabricators requiring the smallest possible light gap achievable, otherwise the “One Cut” dimensions may be used.
C1
C2
C3
C = A - (K + 1/2 L) - (1/2 L + 1/2 L) - (1/2 L + P)
CLUTCH MODEL R8 Clutch
CLUTCH (K) 0.51 13mm
R16 or R24 (no adapters) R16 or R24 (2 inch tube adapters) (50mm tube adapters)
SL-10 or SL-15
0.60
15mm
0.66
16mm
0.64
16mm
14mm
FIRST (–) 0.83
MIDDLE (–) 0.64
LAST (–) 0.89
ONE CUT (OC) (–) 7/8 inch
21mm
16mm
23mm
22mm
0.57
=
(–) 0.92
(–) 0.64
(–) 0.89
(–) 1 inch
14mm
23mm
17mm
23mm
25mm
21mm
16mm
0.63
=
(–) 1.07
(–) 0.81
(–) 1.04
(–) 1 inch
0.62
0.64
0.45
=
(–) 0.94
(–) 0.64
(–) 0.77
(–) 1 inch
0.54
=
(–)0.95
(–) 0.64
(–) 0.86
(–) 1 inch
0.60
=
(–)0.95
(–) 0.81
(–) 1.01
(–) 1 inch
0.63
16mm
SL-20 or SL-30 (2 inch tube adapters) 0.69
(50mm tube adapters) 18mm
0.81
PIN END (P) 0.57 =
17mm 16mm
SL-20 or SL-30 (no adapters)
LINK (L) 0.64
16mm
0.64
16mm
0.81
21mm
11mm
14mm
15mm
27mm
24mm
24mm
24mm
21mm
16mm
16mm
21mm
26mm
20mm
22mm
26mm
25mm
25mm
25mm
C = A - (number of shades x OC) = C For example: If youʼre linking two shades and measurement "A" is 38 inches (965mm), and you're using SL-15 clutches with “One Cut” deduction; "OC" is 1 inch... (38" - (2 x 1") = 36") "C" = 36 inches. "OC" is 25mm... (965mm - (2 x 25mm) = 915mm) "C" = 915 mm
www.rollease.com RollEase Headquarters 200 Harvard Avenue - Stamford, CT 06902-6320 USA Office: 800.552.5100 203.964.1573 Fax: 203.964.0513 Order Fax: 203.358.5865
© 2010 RollEase, Inc.
Rev: 4.23.2010
RollEase West 7150 West Roosevelt Street, Suite-A-155 Phoenix, AZ 85043 USA Office: 623.936.5818 Fax: 623.936.5294
25mm
RollEase Link System Roller Shade Installation Instructions R-Series, Skyline Clutch or motor and corresponding 2 inch projection (50mm) Mounting Bracket Primary Shade 1-1/2 inch (38mm) tube
Link System Components Link System Housing
Link J Bracket Infinite Adjuster
Drive Shade Pin End and 2 inch (50mm) projection bracket to match Clutch system used
Bearing Grip Wheel
Driven Shade 1-1/2 inch (38mm) tube Locking Tab Bracket Options Clutch and pin end brackets must have a 2 inch (50mm) Drive projection to match the 2 inch (50mm) projection of the link bracket. R-Series: RB-380, RB-580 www.AV-Outlet.com Skyline: SLB-680, SLNB-680 Figure 1
1. Mount the clutch-side bracket, link bracket(s), and pin end side bracket. Note: This system should always be installed the “J” opening outward or upward, never facing downward and requires the use of clutch and pin end brackets with 2 inch (50mm) projections (RB-380, RB-580, SLB-680, or SLNB-680) (See Figure 1)
Figure 2
2. Insert the clutch (or motor) into one end of the Primary roller shade tube and the housing into the opposite end. (See Figure 2) Note: The Infinite Adjuster can never be used on the same tube as the clutch (or motor).
Figure 4
4. Insert one the end of the triangular shaped drive link through the bearing (See Figure 4)
Figure 5
5. Slide the triangular link and bearing onto the housing. (See Figure 5)
www.rollease.com RollEase Headquarters 200 Harvard Avenue - Stamford, CT 06902-6320 USA Office: 800.552.5100 203.964.1573 Fax: 203.964.0513 Order Fax: 203.358.5865
© 2010 RollEase, Inc.
Rev: 4.23.2010
RollEase West 7150 West Roosevelt Street, Suite-A-155 Phoenix, AZ 85043 USA Office: 623.936.5818 Fax: 623.936.5294
Figure 3
3. Insert the pin end into the furthest end of the Driven shade(s) and the Infinite Adjuster into the other end. The Infinite Adjuster will be horizontally opposed to the housing of its neighboring shade. When three shades are being linked, another housing must be inserted in place of the pin end in the middle shade. The pin end will always be at the end of the third shade. (See Figure 3) Figure 6
6. Slide the Infinite Adjuster end of the neighboring tube onto the drive. When installing three shades, repeat Steps 4 through 6.
RollEase Link System Roller Shade Installation Instructions Primary Shade
7.
8.
9.
For installation of 3 shades, skip ahead to Step 9 TWO SHADE INSTALLATION All the link shades should be connected and installed together treating them as one unit. While the ends of the shades that are being linked are supported, insert the clutch and pin end into their respective brackets. This will cause the shades to bow down in a “V”-like shape. If the shades are large this will require two installers. The shades require support and should not be left to hang by the clutch and pin end alone. (See Figure 7) Slide the assembly up and over into the J-Bracket making sure the curved edge of the bearing faces the matching curve in the J-bracket. (See Figure 8) Skip ahead to Step 11
Figure 7
Figure 8
THREE SHADE INSTALLATION When installing three shades, all tubes must be connected and treated like they are all one shade being installed. While the ends of the shades that are being linked are supported, insert the clutch and pin end into their respective Primary Shade brackets. This will cause the shades to bow down in a “V”-like shape. If the shades are large this will require multiple installers. The shades require support and should not be left to hang by the clutch and pin end alone. (See Figure 9) The clutch and pin end must be inserted before all tubes in the assembly are simultaneously lifted into position in the link brackets. It is not possible to install one shade at a time; unless it is in an outside mount with ample room on either Figure 10 side. www.AV-Outlet.com
Driven Shade
10. Slide the assembly up and over into the J-Bracket making sure the curved edge of the bearing faces the matching curve in the J-bracket. (See Figure 10) 11. Insert the locking tab securely onto the J-Brackets. When properly installed you should hear or feel a latching of the parts. (See Figure 11) 12. Once secured, use the grip wheel on the Infinite Adjuster to adjust the shade on the corresponding tube until it becomes level with the shade on the clutch tube. The level of adjustment is infinitely fine due to RollEaseʼs patented technology. (Figure 12) Figure 12
www.rollease.com RollEase Headquarters 200 Harvard Avenue - Stamford, CT 06902-6320 USA Office: 800.552.5100 203.964.1573 Fax: 203.964.0513 Order Fax: 203.358.5865
© 2010 RollEase, Inc.
Rev: 4.23.2010
RollEase West 7150 West Roosevelt Street, Suite-A-155 Phoenix, AZ 85043 USA Office: 623.936.5818 Fax: 623.936.5294
Driven Shade
Driven Shade
Figure 9
Figure 11