Slee Off Road 200 Series Step Sliders (SOF1119) - Toyota Land ...

700 Pine Ridge Road Golden CO 80403 Tel (303) 278 8287 1(888) 4X4 SLEE Fax (303) 278 7182

Slee Off Road 200 Series Step Sliders (SOF1119) - Toyota Land Cruiser 2008+

Qty

Parts Included

Suggested Tool List

Slider Steps - Pair Slider Step Plates - Pair

Hand Tools Pneumatic Tools

27

M8 x 1.25 x 35MM

16

M8 Rivet Nuts

M8 Rivet Nut Tool * Supplied Separately 17/32” Drill Bit

27 24

M10 Thick Washers 10-32 Stainless Counter Sink Bolts

24 24

10-32 Stainless Flat Washers 10-32 Stainless Nylock Nuts

1 1

2 2

1/2” Nut Plate 1/2” Thick Washers

2 2

1/2” Allen Bolts M8 x 20 x 1 Button Head Allen

Thank you for your purchase from Slee Off-Road! If you should you have any questions or concerns, please do not hesitate to contact us immediately at 1 888 4X4 SLEE or at [email protected]. Slee Off Road strives to provide comprehensive installation instructions. However, in some circumstances minor inconsistences may be encountered with instructions and or provided parts. If you encounter such an inconsistency, please notify us, as your input is important. Slee Off-Road guarantees all parts free from defects for one year from the original purchase date.

Copyright © by Slee Off Road and Slee & Company The entire content of this document is property of Slee Off Road and may not be used or reproduced without permission. Slee Off Road (200 Sliders) Rev 1.2 – 6/13

Slee Off Road 200 Series Step Sliders - Toyota Land Cruiser 2008+ - 2 of 6 1. Install the thread plates on the Step Sliders using the 10-32 Counter Sink Bolts, Flat Washers and Nylock Nuts.

Install thread plates to sliders (Step 1)

2. Remove the 8mm bolts on driver and passenger side frame rails that attach the brake cable to the frame.

Remove bolts from brake cable bracket (Step 2)

3. Remove Gas Tank Skid Plate on passenger side.

Remove the Gas Tank Skid Plate (Step 3)

4. Remove four bolts that secure the Hydraulic Line to the frame rail on the driver side.

Remove bolts that secure the Hydraulic Line (Step 4)


Slee Off Road 200 Series Step Sliders - Toyota Land Cruiser 2008+ - 3 of 6 5. Install M8 Rivet Nuts on the driver side frame rail. Tools; M8 Rivet Nut Tool and a 17/32” Drill bit. Hint; it may be necessary to place the slider against the frame rail temporarily to determine all locations for Rivet nuts.

Install Rivet Nuts on driver side for front leg (step 5A)

Install Rivet Nuts on driver side for rear leg (Step 5B)

6. Install the Drivers side Step Slider. Hint; a jack stand may be helpful when installing the sliders.

Front Driver Side leg installed (Step 6A)

Rear Driver side leg shown installed (Step 6B)


Slee Off Road 200 Series Step Sliders - Toyota Land Cruiser 2008+ - 4 of 6

Rear driver side leg shown installed for reference

Rear driver side leg shown installed for refernece

7. Install 1/2” Nut Plate, 1/2” Thick Washer and 1/2” Allen Bolt by removing body mount. Note; shown without slider although previously installed in step six. Also, “A” indicates location of the M8x20x1 Button Head Allen (although shown otherwise). Install one on driver and passenger side. Nut Plate installation process for driver (and passenger) front leg shown (Step 7A)

A

Allen bolt shown installed (Step 7B)


Slee Off Road 200 Series Step Sliders - Toyota Land Cruiser 2008+ - 5 of 6 8. Install Hydraulic line that was removed in step four using supplied hardware. Install Brake Line that was removed in step two. 9. Install M8 Rivet Nuts in the passenger side frame rail. Hint; it may be necessary to place the slider against the frame rail temporarily to determine all locations for Rivet nuts.

Install Rivet Nuts on passenger side for front and rear Slider leg (Step 9A)

10. Install the Passenger Step Slider leaving the holes open where the gas tank skid plate brackets are located. Install the gas tank skid plate (photo 7B).

Front Passenger side leg installed (Step 10A)

Rear passenger side leg shown installed for refernece


Slee Off Road 200 Series Step Sliders - Toyota Land Cruiser 2008+ - 6 of 6

Rear passenger side leg shown installed for refernece

Rear passenger side leg shown with gas tank skid plate (Step 10B)

11. Install 1/2” Nut Plate, 1/2” Thick Washer and 1/2” Allen Bolt by removing body mount. Note; reference step seven. 12. Install Brake Line that was removed in step two. 13. Installation complete.

Installation complete (Step 8)

Thank you for your purchase from Slee Off-Road! Visit us at sleeoffroad.com or email us at [email protected].
