SERVICE MANUAL. EG 011620 ... This document is printed on chlorine free (
ECF) paper with soy ink. Guitar .... SILENT GUITARMODEL SLG-100N. OPEN.
Guitar
SLG-100N SERVICE MANUAL
CONTENTS
This document is printed on chlorine free (ECF) paper with soy ink.
SPECIFICATIONS ................................................. 3 PANEL LAYOUT ...................................... 4 CIRCUIT BOARD LAYOUT ................. 6 DISASSEMBLY PROCEDURE .............................. 7 LSI PIN DESCRIPTION .............................. 10 IC BLOCK DIAGRAM .................................... 10 CIRCUIT BOARDS ........................................ 11 INSPECTIONS ............................................................ 12 TUNING ...................................................................... 13 OVERALL CIRCUIT DIAGRAM ........................... 14 PARTS LIST
EG 011620 20011220-62000
HAMAMATSU, JAPAN 1.018K-916
Printed in Japan ’02.01
SLG-100N
IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
WARNING :
Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative.
IMPORTANT :
This presentation or sale of this manual to any individual or firm does not constitute authorization certification, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor’s Service Division.
WARNING :
Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.)
IMPORTANT :
Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
WARNING Components having special characteristics are marked originally installed.
2
and must be replaced with parts having specification equal to those
SLG-100N
SPECIFICATIONS Neck
Mahogany
Body
Maple
Fingerboard
Rosewood
Bridge
Rosewood
Frame Unit
Maple
Strings
Nylon Guitar Strings
Sensors
B-BAND
Connectors/Controls • • • • • • • • • •
AUX IN AUX IN Level Control LINE OUT jack (monaural) PHONES jack (stereo) Volume BASS control TREBLE control REVERB switch (OFF/1/2) PHONES switch (ON/OFF) LINE OUT Jack with POWER Switch (Inserting a plug into the jack switches the power on)
Power Supply
• AC Adaptor/6F22 (S-006P) battery x1 dual power source * Recommended AC Adaptors: PA-D09, PA1E, PA-3B
Battery Life
Continuous Use • Using Manganese battery : approximately 13.5 hours • Using Alkaline battery : approximately 24 hours With the reverb activated • Using Manganese battery : approximately 2 hours • Using Alkaline battery : approximately 7.5 hours
Input/Output Specifications Input Level • AUX IN: -40 dBm/1kHz sine wave (REVERB OFF) Output Level • LINE OUT: -27 dBm/10k Ω • PHONES (L/R): -31 dBm/39 Ω Power Consumption Using AC adaptor (PA-D09) • REVERB OFF: 1.9 W 1- 2 : 2.4 W Using battery • REVERB OFF: 0.2 W 1- 2 : 0.6 W String Length
650 mm (25-9/16”)
Dimensions
965 (L) x 365 (W) x 80 (H) mm 38” (L) x 14-3/8” (W) x 3-1/8” (H) (with the left frame attached and to the end of the strap pin)
Weight
approximately 1.8 kg (3 lbs. 15 oz.)
Accessories
AC adaptor (PA-D09), * May not be in your area. Stereo earphones, Soft case
3
SLG-100N
PANEL LAYOUT
Front
Rear
Tuning peg
Nut
Fingerboard
Neck Frame Attachment Screw 1 (Doubles as the Strap Pin)
Left Frame (Removable)
Right Frame (Fixed)
Horn (Leg Support)
Body OPEN
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDEITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. ¥ THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. ¥ CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME ¸ LA NORME NMB-003 DU CANADA.
D
SILENT GUITAR MODEL SLG-100N ERIFIE AC POWER ADAPTOR : EMC YAMAHA PA-1E OR PA-3B OR PA-D09 SEMKO BATTERY : 9V 6LR61 OR 6F22Y MADE IN TAIWAN V
Saddle
N89
AUX VOL
MIN
LINE OUT
MAX
AUX IN
Pickup (underneath the saddle)
Bridge Controls → See page 5.
Frame Attachment Screw 2 (Doubles as the Strap Pin)
4
SLG-100N
Controls
6F22 (S-006P) 9V battery POWER lamp OPEN
OFF 1 2
REVERB VOLUME
DC-IN jack
VOLUME control
TREBLE control OFF ON
SILENT GUITAR MODEL SLG-100N ERIFIED AC POWER ADAPTOR : EMC YAMAHA PA-1E OR PA-3B OR PA-D09 SEMKO BATTERY : 9V 6LR61 OR 6F22Y MADE IN TAIWAN V
–
TREBLE
+
BASS control
BASS
DC-IN 9~12V
(Power adaptor connector) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDEITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. ¥ THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. ¥ CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME ¸ LA NORME NMB-003 DU CANADA.
REVERB switch
N89
PHONES
PHONES ON/OFF switch
AUX VOL
Cord hook PHONES jack MIN
LINE OUT
MAX
AUX IN
AUX IN level control
LINE OUT jack
AUX IN jack
5
SLG-100N
CIRCUIT BOARD LAYOUT
Body (rear view) (underneath the panel assembly)
Panel Assembly
MA
PUP
AUX
Jack
6
SLG-100N
DISASSEMBLY PROCEDURE Preparations Make the following preparations; Turn off the power switch. Remove the battery cover and battery.
1. Left Frame (Time required: About 2 minutes) 1-1 Loosen the adjusting bolt (front) marked [E15] and the adjusting bolt (rear) marked [E16]. The left frame can then be removed. (Fig.1) 2.
Bracket Assembly, Bracket, Sleeve (Time required: About 5 minutes each)
2-1 Remove the left frame. (See procedure 1.) 2-2 Bracket Assembly: Remove the two (2) screws marked [D05]. The upper bracket assembly can then be removed from the left frame. (Fig.1) The lower bracket assembly can be removed in the same manner. 2-3 Bracket, Sleeve: Remove the two (2) screws marked [E19]. The upper bracket and the upper sleeve can then be removed. (Fig.1) The lower bracket and the lower sleeve can be removed in the same manner.
3. Right Frame (Time required: About 2 minutes) 3-1 Remove the four (4) screws marked [E22]. The right frame can then be removed with the horn. (Fig.1) 4. Horn, Right Bracket (Time required: About 5 minutes each) 4-1 Remove the right frame. (See procedure 3.) 4-2 Horn: Remove the two (2) screws marked [D08]. The horn can then be removed. (Fig.1) 4-3 Right Bracket: Remove the two (2) screws marked [E21]. The upper right bracket can then be removed. (Fig.1) The lower right bracket can be removed in the same manner. Peg Peg
Bracket
String Panel holder assembly
Bracket assembly
[F02] X 4 [E15]
Panel holder
[E19] [D05]
Spacer
Sleeve
[E22]
PUP Pickup
Left frame Bracket assembly
[E21] Right bracket
Horn
[E19] [D08] Right bracket [D05] [E21]
Sleeve Bracket
Right frame
[E16] [E22]
[D05]: Flat Head Tapping Screw-2 3.0X8 (QC667000) [D08]: Flat Head Tapping Screw 3.5X20 (QC667100) [E15]: Adjusting Bolt, Front M6.0XP1X25 (QC653400) [E16]: Adjusting Bolt, Rear M6.0XP1X12 (QC653500) [E19]: Flat Head Tapping Screw 3.0X14 ZMC2BL (QC699200) [E21]: Flat Head Tapping Screw 3.0X14 ZMC2BL (QC699200) [E22]: Flat Head Tapping Screw-2 3.0X8 (QC667000) [F02]: Bind Head Tapping Screw-1 3.0X10 ZMC2BL (20404200)
Fig.1
7
SLG-100N
5. Peg (Time required: About 5 minutes) 5-1 Remove the three (3) strings in left side (4th-6th strings) and right side (1st-3rd strings) each. (Fig.2) 5-2 Remove the four (4) screws marked [E03] in left and right each. The left and right pegs can then be removed. (Fig.2)
Peg
[E03]
Peg
[E03]
Left side Strings (4th-6th) Right side Strings (1st-3rd)
[E03]: Round Head Wood Screw
Fig.2 6. Panel Assembly (Time required: About 2 minutes) 6-1 Remove the four (4) screws marked [F05] and the four (4) screws marked [F06]. The panel assembly can then be removed. (Fig.3) 7.
MA Circuit Board, AUX Circuit Board, Jack (LINE Connector Assembly) (Time required: About 5 minutes each)
7-1 Remove the panel assembly. (See procedure 6.) 7-2 MA Circuit Board: Pull out the three (3) rotary knobs for [VOLUME], [BASS] and [TREBLE]. (Fig.3, 4) Remove the two (2) screws marked [16A]. The MA circuit board can then be removed. (Fig.4) 7-3 AUX Circuit Board: Pull out the AUX knob and remove the screw marked [16B]. The AUX circuit board can then be removed with the jack holder. (Fig.3, 4, 5) Remove the hexagonal nut marked [A]. The jack holder can then be removed from the AUX circuit board. (Fig.5) 7-4 Jack (LINE Connector Assembly): Remove the hexagonal nut marked [10]. The jack (LINE connector assembly) can then be removed. (Fig.3, 4)
8
2.1X8 (03714060)
SLG-100N
8. PUP Circuit Board (Time required: About 5 minutes) 8-1 Remove the panel assembly. (See procedure 6.) 8-2 Remove the four (4) screws marked [F02]. The panel holder assembly can then be removed. (Fig.1) 8-3 Remove the PUP circuit board from the two (2) spacers. (Fig.1) 9. 9-1 9-2 9-3 9-4 9-5
Pickup (Time required: About 5 minutes) Remove the panel assembly. (See procedure 6.) Turn each pegs and loosen the strings. (Fig.1, Photo.1) Remove the bridge saddle. (Photo.1) Remove the pickup from the slot on the bridge. (Photo.1) Disconnect the connector from the PUP circuit board. (Fig.1)
Rotary knob Jack (LINE connector assembly) [TREBLE] [VOLUME] [BASS]
AUX knob [16B]
[A]
AUX
[F05]
[F06]
[F05]: Bind Head Tapping Screw-1 [F06]: Bind Head Tapping Screw-B [10]: Hexagonal Nut [16B]: Bind Head Tapping Screw-B
[10]
Jack holder
[F05]
3.0X10 ZMC2BL (20404200) 3.0X10 ZMC2BL (EP600140)
[A]: Hexagonal Nut
(AA820860)
Fig.5
3.0X10 ZMC2BL (EP600140)
Fig.3
MA
[16A]
Jack (LINE connector assembly)
Bridge saddle
String
Bridge
[16A] [BASS] [TREBLE] [VOLUME] Rotary knob
[16A]: Bind Head Tapping Screw-B
AUX
Pickup
Photo.1
3.0X10 ZMC2BL (EP600140)
Fig.4
9
SLG-100N
LSI PIN DESCRIPTION YSS234 (XN299A00) DSP (Digital Sound Processor) PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
NAME
I/O
MD4 MD3 MD0 MD1 MD2 MCKO XO XI ER0 ER1 ER2 REV0 REV1 REV2 MUTEN ICN PRG MODE VSS AVSS CVA AORL AORR CHL AIL VDD AIR CHR AOFL AOFR AVDD CVB
FUNCTION
I/O I/O I/O I/O I/O O O I I I I I I I I I I I O O I I I I O O I
External RAM interface data
Master clock output Crystal oscillator connection Crystal oscillator connection
Eary refrection preset select
Effect select DC D+5V Initial clear DC D+5V Preset mode (H=DC +5V) Ground Ground N.C. N.C. N.C. Sample hold capacitor connection Lch ADC input DC D+5V Rch ADC input Sample hold capacitor connection Lch DAC output Rch DAC output DC A+5V Rch midpoint voltage
MA: IC01
PIN NO.
NAME
I/O
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
AVDD VDD TST0 TST1 DOEN SDO1 SDO0 WC BCO MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA12 MA14 VSS MA10 MA011 MA09 MA8 MA13 VDD WEN OEN CEN MD7 MD6 MD5
O O O O O O O O O O O O O O O O O O O I I I I/O I/O I/O
IC BLOCK DIAGRAM NJM3404AM (XM527A00) Dual Operational Amplifier
NJM3414AM (XR294A00) Dual Operational Amplifier
MA: IC08-13 PUP: IC15
MA: IC14
Output A Inverting Input A Non-Inverting Input A Ground
10
1
+V
2
-
3 4
7
+ +
-V
8
-
6 5
+DC Voltage Supply Output B Inverting Input B Non-Inverting Input B
Output A Inverting Input A Non-Inverting Input A -DC Voltage Supply
1
+V
2
-
3 4
+ +
-V
-
8
+DC Voltage Supply
7
Output B
6 5
Inverting Input B Non-Inverting Input B
FUNCTION DC A+5Vs bus DC D+5V DC D+5V DC D+5V DC D+5V N.C. N.C. N.C. N.C
External RAM interface address
Ground
External RAM interface address
DC D+5V Write enable Output enable Chip select
External RAM interface data
SLG-100N
CIRCUIT BOARDS MA Circuit Board
POWER Lamp
Note: See parts list for details of circuit board component parts. GR
REVERB OFF/1/2 VOLUME BASS to LINE OUT Jack
TREBLE
DC-IN 9~12V
ON/OFF PHONES
to Battery terminal
Component side
PUP Circuit Board
Pattern side
AUX Circuit Board AUX IN
AUX VOL MIN/MAX
to Pickup (B-BAND)
Component side ENA-V872950-1, 2
0
Pattern side
Component side
Pattern side 11
SLG-100N
INSPECTIONS 1. Required Equipment High-sensitivity AC voltmeter (level meter) Battery (006P) or power adapter (PA-D09) 2. Noise Level Measurement Load resistance [PHONES] jack: 39Ω (right and left each) [LINE OUT] jack: 10kΩ (1) Turn on the power to the main unit, turn on the [PHONES] switch, and check that the power LED (green) lights up. (2) Connect the level meter to the [PHONES] jack. (3) Turn the [VOLUME], [BASS] and [TREBLE] control dials to the right most position (MAX). (4) Stop the strings vibrating, measure the noise level, and check that the noise levels for both right and left channels are –60dBm or less. (5) Disconnect the level meter from the [PHONES] jack and connect it to the [LINE OUT] jack instead. (6) Stop the strings vibrating, measure the noise level, and check that the noise level is –60dBm or less. 3. Reverberation Inspection (1) Connect a headphone to the [PHONES] jack. (2) Pluck a string, switch the [REVERB] switch from “OFF” to “1” and then to “2”, and check that the following effect is present at both right and left headphone outputs. REVERB 1 2
Mode (reverberating time) HALL (1.0 sec) HALL (3.0 sec)
(3) Turn the [VOLUME] control dial to the left most position (MIN). (4) Disconnect the headphone from the [PHONES] jack.
12
SLG-100N
TUNING Use a tuning meter, pitch pipe, tuning fork, piano, etc., and to the open strings to the pitches shown below. •
If the string’s pitch is high, loosen the string until the string’s pitch is slightly lower than the tuning pitch, then tune while raising the string’s pitch.
Open 1st String's Pitch: E Open 2nd String's Pitch: B Open 3rd String's Pitch: G Open 4th String's Pitch: D Open 5th String's Pitch: A Open 6th String's Pitch: E
Play the standard pitch “lah” (A3: 440Hz) on a tuning fork, etc., and tune the open 5th string to the same pitch. Play the pitch produced by pressing the 5th string at the 5th fret, and tune the open 4th string to the same pitch. Play the pitch produced by pressing the 4th string at the 5th fret, and tune the open 3rd string to the same pitch. Play the pitch produced by pressing the 3rd string at the 4th fret, and tune the open 2nd string to the same pitch. Play the pitch produced by pressing the 2nd string at the 5th fret, and tune the open 1st string to the same pitch. Play the pitch produced by pressing the 6th string at the 5th fret, and tune the pitch at the 5th fret of the 6th string to the pitch produced by the open 5th string.
Open 1st String's Pitch: E
1F
2F
3F
4F
5F
nd
Open 2 String's Pitch: B Open 3rd String's Pitch: G Open 4th String's Pitch: D Open 5th String's Pitch: A Open 6th String's Pitch: E
13
OVERALL CIRCUIT DIAGRAM
PUP CN5 RE-H022SD-1190
MA Note: D7 is not installed.
VOLUME
SRAM 256K OP AMP 22K
PHONES
OP AMP
22K
DSP Note
22K
SYSTEM RESET
22K
SYSTEM RESET
OP AMP LINE OUT
TONE CONTROL
OP AMP
AUX
OP AMP
TREBLE 1K
AUX VOL
1K 0.012u
OP AMP 3.3K
AUX IN
BASS REVERB OFF/1/2
REGULATOR +5V
OP AMP
REGULATOR +8V BATTERY (+9V)
OP AMP
DC-IN 9~12V
+
–
SYSTEM RESET NJU7202U50(X0150A00) REGULATOR +5V
NJM78L08UA(XN00A00) REGULATOR +8V Power Lamp GR
1
2
1 3 1: COMMON 2: INPUT 3: OUTPUT
: Mylar Capacitor
Note : See parts list for details of circuit board component parts.
2
3 1: OUTPUT 2: COMMON 3: INPUT
TO SERVICE PERSONNEL Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.
STE-GA00P-04
2
SLG-100N
14
to Pickup (B-BAND)
Guitar
SLG-100N PARTS LIST CONTENTS OVERALL ASSEMBLY PANEL ASSEMBLY ELECTRICAL PARTS Notes : DESTINATION ABBREVIATIONS A : Australian model B : British model C : Canadian model D : German model E : European model F : French model H : North European model I : Indonesian model J : Japanese model
.............................................. 2 ......................................... 4 ............................................. 6
M : South African model O : Chinese model Q : South-east Asia model T : Taiwan model U : U.S.A. model V : General export model (110V) W: General export model (220V) N,X: General export model Y : Export model
WARNING Components having special characteristics are marked specification equal to those originally installed.
and must be replaced with parts having
The numbers “QTY” show quantities for each unit. The parts with “--” in “PART NO.” are not available as spare parts. This mark “ } ” in the REMARKS column means these parts are interchangeable. ) part number is O, not zero. The second letter of the shaded ( ) part number is I, not one. The second letter of the shaded (
SLG-100N
OVERALL ASSEMBLY
F05
E01 F06 E03 E01 E03 F04 Panel assembly: See page 4.
E04 Panel holder assembly
F01 E14 E13
E12
F02
A01 E10
E09
F01a
E11 D04 F01b D01
E15
F01d
F01e
E19 E17
F01c E18
D05
F01d F03 F07
F09
D03
E22 F08 E05
E08 D04
D07
E20
E06
E21 D02
E07
E20
D08
D05 E21
D06 E19 E17
E22 E18
2
E16
SLG-100N
Accessories H01 AC Adapter
REF NO.
PART NO.
H02 Stereo Earphones
DESCRIPTION
REMARKS
OVERALL ASSEMBLY Body
--
* * * * * * * *
D01 D02 D03 D04 D05 D06 D07 D08
24173400 QC665900 QC653700 QC655100 QC667000 QC653600 QC655400 QC667100
Nut Nut Left Frame Bracket Assembly Flat Head Tapping Screw-2 Right Frame Horn Flat Head Tapping Screw
S M6.0XP1 L=13 S M6.0XP1 L=10
*
E01 E03 E04 E05 E06 E07 E08 E09 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E21 E22
QC666400 03714060 QC656400 QC655200 20454100 03377460 QC656500 ------QC653400 QC653500 QC693600 QC653300 QC699200 QC653100 QC699200 QC667000
Tuning Machine Assembly Round Head Wood Screw Nut Bridge Oval Head Wood Screw Cap Bridge Saddle String 1 String 2 String 3 String 4 String 5 String 6 Adjusting Bolt, Front Adjusting Bolt, Rear Bracket Sleeve Flat Head Tapping Screw Right Bracket Flat Head Tapping Screw Flat Head Tapping Screw-2
Pingway RM-1388 2.1X8 (Brass) Urea 50mm (White) Indian Rosewood 2.4X16 (Chrome) M5.0 (White) Urea 82mm (White) CG S11 CG S12 CG S13 CG S14 CG S15 CG S16 M6.0XP1X25 (Black) M6.0XP1X12 (Black) (Black) (Blue) 3.0X14 ZMC2BL (Black) 3.0X14 ZMC2BL 3.0X8(Black Chrome)
F01 * F01a * F01b * F01c F01d F01e * F02 F03 F04 * F05 F06 F07 F08 * F09
-QC660000 V8729900 QC662400 --20404200 --20404200 EP600140 QC624400 -QC679000
Panel Holder Assembly Panel Holder Circuit Board Spacer Sponge Connector Assembly Bind Head Tapping Screw-1 Aluminum Sheet Panel Assembly Bind Head Tapping Screw-1 Bind Head Tapping Screw-B Pickup Adhesive Tape Cushion
H01 H01 H01 H02 H03
V8285200 V8285300 V8285400 QC667400 QC666900
ACCESSORIES AC Adapter AC Adapter AC Adapter Stereo Earphones Soft Case
*
* * * * * * * *
* * * * *
: New Parts
QTY
RANK
SLG-100N
A01
* *
H03 Soft Case
#0186130 #0186100
3.0X8(Black Chrome)
2 4
Maple 3.5X20(Black Chrom)
2 (Gold) 1set 8
01
2 2
01 01
(QA33300) (QA33310) (QA33320) (QA25310) (QA25320) (QA25330)
2 2 4 2 4 4
(Black) (Black)
(QC66260) PUP ACBS-2 (PINGOOD) 8X8 t=7 PUP PHR-5P L=70 3.0X10 ZMC2BL
(QC68960) (QC66180) (Black)
2 2 4
(QC66250) (QC66720) 3.0X10 ZMC2BL 3.0X10 ZMC2BL B-Band 29S 12X50 t=0.2 8X12 t=1
(Black) (Black)
PA-D09 J PA-D09 UL PA-D09 CE
J U,C H
4 4
01
(QC66730)
RANK: Japan only
3
SLG-100N
PANEL ASSEMBLY
13
2
16
4
1 6 15
3 16 12
16
18
5 14
8 7
11
19
10 9 18 9a 17
4
16
SLG-100N
REF NO.
* *
* * *
*
* *
1 2 3 4 5 6 7 8 9 9a 10 11 12 13 14 15 16 17 18 19
PART NO. -QC659900 QC660200 V2300100 QC187700 VC407100 V8729700 V8729800 QC660100 -LB201120 AA820860 AA820850 QC661500 ---EP600140 QC679000 QC689700 --
: New Parts
DESCRIPTION PANEL ASSEMBLY Control Panel Battery Cover AUX Knob Rotary Knob DC Cord Column Circuit Board Circuit Board Jack Holder Connector Assembly Jack Hexagonal Nut Flat Washer Connector Assembly Sponge Adhesive Tape Name Plate Sticker Bind Head Tapping Screw-B Cushion Flat Washer Cushion
REMARKS SLG-100N
QTY
RANK
3
04 05 02
(QC66720)
(Black) (Black) AUX VOL VOLUME,BASS,TREBLE MA AUX LINE PHR-3P JL2B X-G7639 (Black) (Black) BT PHR-2P L=280 20X37 t=4 (Gray) 5X20 t=0.2 3.0X10 ZMC2BL 8X12 t=1 3.0X8X0.5 ZMC2BL 20X20X13 (Black)
(QC66160) LINE OUT
03 01 01
with Battery snap (QC66190) (QC66730) (QC66230) (Black)
2
4
(Black)
01
2 (QC70870)
RANK: Japan only
5
SLG-100N
ELECTRICAL PARTS REF NO.
* * * * * C01 C02 C03 C04 C05 C06 C07 C08 C09 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 -51 C52 -55 CC01 -03 * CC04 * CC05 CC06 CC07 CC08 CC09 CC10 CC11 CC12 CC13
PART NO.
REMARKS
QTY
MA AUX PUP
(V872950)(X2450C0) (V872950)(X2450C0) (V872950)(X2450C0)
V8729700 QC662200 UA654470 UA354120 US145100 US062150 UA654180 UA654100 US063330 US145100 UA653220 UA652560 UA654680 US061220 US061220 US062100 UA654100 UA654220 UA654220 US145100 US063330 UA654220 US145100 UA654220 US063330 US145100 US145100 US062100 US062100 UA654470 UA654470 US145100 UA654100 UA654100 US145100 US145100 UA654220 UA654220 US145100 US063150 US063150 US145100 UA654680 UA654680 US145100 US063470 US145100 US062330 US145100 US062150 US062150 US145100 US145100 UM388100 UM388100 V6796100 V6796100 UN865470 UM398100 UM397100 UM398100 UM406470 UM416100 UM416100 UM397470
MA LEH5-4.5T 0.047u 50V J 0.012u 50V J 0.1u 25V Z 150P 50V J 0.018u 50V J 0.01u 50V J 3300P 50V K 0.1u 25V Z 2200P 50V J 560P 50V J 0.068u 50V J 22P 50V J 22P 50V J 100P 50V J 0.01u 50V J 0.022u 50V J 0.022u 50V J 0.1u 25V Z 3300P 50V K 0.022u 50V J 0.1u 25V Z 0.022u 50V J 3300P 50V K 0.1u 25V Z 0.1u 25V Z 100P 50V J 100P 50V J 0.047u 50V J 0.047u 50V J 0.1u 25V Z 0.01u 50V J 0.01u 50V J 0.1u 25V Z 0.1u 25V Z 0.022u 50V J 0.022u 50V J 0.1u 25V Z 1500P 50V K 1500P 50V K 0.1u 25V Z 0.068u 50V J 0.068u 50V J 0.1u 25V Z 4700P 50V K 0.1u 25V Z 330P 50V J 0.1u 25V Z 150P 50V J 150P 50V J 0.1u 25V Z 0.1u 25V Z 100u 6.3V 100u 6.3V 220u 10V 220u 10V 0.47u 50V 100u 16V 10u 16V 100u 16V 4.7u 25V 1u 50V 1u 50V 47u 16V
(V872950)(X2450C0)
: New Parts
6
DESCRIPTION
ELECTRICAL PARTS V8729700 Circuit Board V8729800 Circuit Board V8729900 Circuit Board Circuit Board LED Holder Mylar Capacitor Mylar Capacitor Ceramic Capacitor-F (chip) Ceramic Capacitor-SL(chip) Mylar Capacitor Mylar Capacitor Ceramic Capacitor-B (chip) Ceramic Capacitor-F (chip) Mylar Capacitor Mylar Capacitor Mylar Capacitor Ceramic Capacitor-CH(chip) Ceramic Capacitor-CH(chip) Ceramic Capacitor-SL(chip) Mylar Capacitor Mylar Capacitor Mylar Capacitor Ceramic Capacitor-F (chip) Ceramic Capacitor-B (chip) Mylar Capacitor Ceramic Capacitor-F (chip) Mylar Capacitor Ceramic Capacitor-B (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Mylar Capacitor Mylar Capacitor Ceramic Capacitor-F (chip) Mylar Capacitor Mylar Capacitor Ceramic Capacitor-F (chip) Ceramic Capacitor-F (chip) Mylar Capacitor Mylar Capacitor Ceramic Capacitor-F (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-F (chip) Mylar Capacitor Mylar Capacitor Ceramic Capacitor-F (chip) Ceramic Capacitor-B (chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-F (chip) Ceramic Capacitor-F (chip) Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-BP Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS
RANK
SLG-100N
01 01 01 01 01 01 01 01 01 02 02 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02 01 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 01 01 RANK: Japan only
SLG-100N
REF NO.
* * *
*
CC14 CC15 CC16 CC17 CC18 CC19 CN1 CN2 CN3 CN4 D01 D02 D03 -05 D06 D08 -13 FT1 -4 IC01 IC02 IC03 IC04 IC05 IC06 IC07 IC08 -13 IC14 JK1 JK2 LD1 R01 R02 R03 R04 R05 R06 R07 R08 R09 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26 R27 R28 R29 R30 R31 R32 R33 -36 R37 R38 R39 -44
PART NO. UM397470 UU148220 V6796100 V6796100 UM398100 UM397100 VB390100 VB389800 VB389900 VB390000 VT532500 VT532500 VS597600 VS597600 VT332900 VT332900 VT332900 VR043100 VR043100 XN299A00 X2200A00 XT627A00 XZ000A00 XT657A00 X0150A00 XN000A00 XM527A00 XM527A00 XR294A00 LB302260 VJ573000 VR043700 RD356270 RD356100 RD356330 RD356100 RD356680 RD357100 RD356100 RD356820 RD355470 RD356100 RD356820 RD355470 RD358100 RD357100 RD356100 RD356120 RD358100 RD358100 RD357100 RD358100 RD356220 RD359100 RD356470 RD355470 RD356220 RD357270 RD356220 RD350000 RD357470 RD356470 RD356470 RD357470 RD357100 RD357100 RD358100 RD358100 RD356220 RD356220
: New Parts
DESCRIPTION Electrolytic Capacitor-KS Electrolytic Capacitor-FW Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Electrolytic Capacitor-KS Connector Base Post Connector Base Post Connector Base Post Connector Base Post Diode Diode Diode Diode Diode Diode Diode FET FET IC IC IC IC IC IC IC IC IC IC Connector ST Mini Jack LED Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip)
REMARKS 47u 16V 220u 25V 220u 10V 220u 10V 100u 16V 10u 16V 5P B5B-PH-K-S 2P B2B-PH-K-S 3P B3B-PH-K-S 4P B4B-PH-K-S 1SR154-400 (1A) 1SR154-400 (1A) RB160L-40 RB160L-40 1SS355 1SS355 1SS355 2SK208-Y 2SK208-Y YSS234 (SP3) UPD43256BGW-70LL-9 PST594C-MMP4P PST9242NR PST594E-MT NJU7202U50 NJM78L08UA NJM3404AM NJM3404AM NJM3414AM HEC0470-01-630 JC-6 Green GL3EG8 2.7K 63M J 1.0K 63M J 3.3K 63M J 1.0K 63M J 6.8K 63M J 10K 63M J 1K 63M J 8.2K 63M J 470 63M J 1K 63M J 8.2K 63M J 470 63M J 100K 63M J 10K 63M J 1K 63M J 1.2K 63M J 100K 63M J 100K 63M J 10K 63M J 100K 63M J 2.2K 63M J 1M 63M J 4.7K 63M J 470 63M J 2.2K 63M J 27K 63M J 2.2K 63M J 0 63M J 47K 63M J 4.7K 63M J 4.7K 63M J 47K 63M J 10K 63M J 10K 63M J 100K 63M J 100K 63M J 2.2K 63M J 2.2K 63M J
QTY
RANK
01
to PUP-CN6 to Battery 9V to LINE OUT to AUX-CN7
DSP SRAM 256K SYSTEM RESET SYSTEM RESET SYSTEM RESET REGULATOR +5V REGULATOR +8V OP AMP OP AMP OP AMP DC-IN 9-12V PHONES POWER lamp
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 11 03 01 03 03 01 03 03 02 02 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 RANK: Japan only
7
SLG-100N
R45 R46 R47 -49 R50 R51 R52 R53 R54 R55 R56 R57 R58 R59 R60 R61 R62 -65 R66 R67 R68 R69 R70 R71 R72 R73 R74 R81 SW1 SW2 TR1 VR1 VR2 VR3 X1
PART NO. RD359100 RD356220 RD358100 RD358100 RD356100 RD357220 RD357220 RD356330 RD356330 RD357180 RD356330 RD356330 RD357180 RD357220 RD357220 RD357100 RD357220 RD357220 RD356100 RD357100 RD154470 RD154470 RD357100 RD357100 RD154470 RD356100 RD358100 RD357100 V8350200 V8190000 VQ986700 V8349900 V8349900 V8349800 VY891500
Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Slide Switch Slide Switch Transistor Rotary Variable Resistor Rotary Variable Resistor Rotary Variable Resistor Quartz Crystal Unit
1M 63M J 2.2K 63M J 100K 63M J 100K 63M J 1K 63M J 22K 63M J 22K 63M J 3.3K 63M J 3.3K 63M J 18K 63M J 3.3K 63M J 3.3K 63M J 18K 63M J 22K 63M J 22K 63M J 10K 63M J 22K 63M J 22K 63M J 1K 63M J 10K 63M J 47 1/4W J 47 1/4W J 10K 63M J 10K 63M J 47 1/4W J 1K 63M J 100K 63M J 10K 63M J SSSU124900 SSSU141800 2SC4081 B10K RK09L1120 B10K RK09L1120 A10Kx2 RK09L12B0 12.288MHz SMD-49
C61 C62 CN7 JK4 VR4
V8729800 US062100 US062100 -VC310700 V3175800
Circuit Board Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Connector Assembly Jack Rotary Variable Resistor
AUX 100P 50V J 100P 50V J AUX 4P L=100 ST. HSJ0912-01-040 A10Kx2 RK14K12D0A6
C56 C57 C58 C59 C60 CC20 * CN5 CN6 FT5 IC15 R75 R76 R77 R78 R79 R80 R82 R83
V8729900 UA654100 UA654470 US062100 US062680 US145100 UI337100 V9083500 VB858400 VR043100 XM527A00 RD357100 RD356470 RD356100 RD358100 RD357220 RD357220 RD359470 RD359470
Circuit Board Mylar Capacitor Mylar Capacitor Ceramic Capacitor-SL(chip) Ceramic Capacitor-SL(chip) Ceramic Capacitor-F (chip) Electrolytic Capacitor Connector Base Post Connector Base Post FET IC Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip)
PUP 0.01u 50V J 0.047u 50V J 100P 50V J 680P 50V J 0.1u 25V Z 10u 16V 2P MB2P-90H 5P S5B-PH-K-S 2SK208-Y NJM3404AM 10K 63M J 4.7K 63M J 1K 63M J 100K 63M J 22K 63M J 22K 63M J 4.7M 63M J 4.7M 63M J
REF NO.
* * * * *
*
*
*
DESCRIPTION
LB201120 Jack QC624400 Pickup
: New Parts
8
REMARKS
JL2B X-G7639 B-Band 29S
QTY
RANK
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 REVERB(OFF/1/2) PHONES(OFF/ON) 01 TREBLE BASS VOLUME 03 (V872950)(X2450C0) 01 01 to MA-CN4 AUX IN AUX VOL
(V875540) 03
(V872950)(X2450C0) 01 01 01 01 01 01 to Pickup (B-Band) to MA-CN1 OP AMP
LINE OUT
01 01 03 01 01 01 01 01 01
03
RANK: Japan only
