SolidWorks

23 downloads 9694 Views 2MB Size Report
Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by .... Training - SolidWorks Routing: Piping and Tubing – 2 Days .
COURSE OUTLINE OF AVAILABLE TRAINING SESSIONS OFFERED AT SOLIDXPERTS ENSURE YOUR SUCCESS WITH SOLIDWORKS … SolidWorks training courses focus on fundamental skills and concepts. As an Authorized SolidWorks Training Center, SolidXperts provides both basic and advanced training of the highest quality. Our trainers are certified by DS SolidWorks Corp. Each course includes a training book, as well as practice sessions for which each participant is given access to a computer.

Course Outlines for SolidWorks ® SolidXperts, inc. All Rights Reserved.

PRODUCT TRAINING MAIN INDEX SOLIDWORKS TRAINING ................................................................................................................. 3 SOLIDWORKS SIMULATION TRAINING ......................................................................................... 23 SOLIDWORKS PDM TRAINING ....................................................................................................... 37 SOLIDWORKS COMPOSER TRAINING .......................................................................................... 41 SOLIDWORKS ELECTRICAL TRAINING ......................................................................................... 43 SOLIDWORKS ADD-IN TRAINING ................................................................................................... 49

SolidWorks Training Index ENSURE YOUR SUCCESS WITH SOLIDWORKS … ......................................................................... 1 Training - SolidWorks Essentials – 4 days (2 sessions) ................................................................ 3 Training - SolidWorks Drawings – 2 Days ........................................................................................ 5 Training - SolidWorks Sheet Metal – 2 Days .................................................................................. 6 Training - SolidWorks Weldments – 1 Day ....................................................................................... 8 Training - SolidWorks Assembly Modeling – 2 Days ...................................................................... 9 Training - SolidWorks Advanced Part Modeling – 2 Days ............................................................ 11 Training - SolidWorks Surface Modeling – 2 Days ........................................................................ 12 Training - SolidWorks Mold Design – 2 Days................................................................................. 13 Training - SolidWorks Routing: Piping and Tubing – 2 Days ....................................................... 15 Training - SolidWorks What's New – 1 Day .................................................................................... 16 Training - SolidWorks Conceptual Design – 3 Days ...................................................................... 18 Training - SolidWorks Industrial Design – 2 Days ......................................................................... 20

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 2

Course Outlines for SolidWorks Training - SolidWorks Essentials – 4 days (2 sessions) (1ST of TWO sessions)

1. SolidWorks Basics and the User Interface ▪ ▪ ▪ ▪ ▪ ▪

What is the SolidWorks Software? Design intent File references Opening files The SolidWorks user interface Using the Command Manager

2. Introduction to Sketching ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

2D sketching Saving files Sketching Sketch entities Basic sketching Rules that govern sketches Design intent Sketch relations Dimensions Extrude Sketching guidelines

3. Basic Part Modeling ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Basic modeling Terminology Choosing the best profile Choosing the sketch plane Details of the part Boss feature Sketching on a planar face Cut feature View Selector Using the Hole Wizard



Filleting

▪ ▪ ▪ ▪ ▪ ▪

Editing tools Detailing basics Drawing views Center marks Dimensioning Changing parameters

4. Symmetry and Draft ▪ ▪ ▪ ▪ ▪ ▪ ▪

Design intent Boss feature with Draft Symmetry in the sketch Sketching inside the model View options Using model edges in a sketch Creating trimmed sketch geometry

5. Patterning ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Why use patterns? Linear pattern Circular patterns Reference geometry Planes Mirror patterns Using pattern seed only Sketch driven patterns

6. Revolved Features ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Design intent Revolved features Building the Rim Building the Spoke Edit material Mass properties Files properties SolidWorks SimulationXpress

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 3

Course Outlines for SolidWorks Training - SolidWorks Essentials – 4 days (2 sessions) (2ND of TWO sessions)

7. Shelling and Ribs ▪ ▪ ▪ ▪ ▪ ▪ ▪

12. Using Drawings ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Shelling and ribs Analysing and adding draft Other options for draft Shelling Ribs Full round fillets Thin features

More about making drawings Section view Model views Broken view Detail Views Drawing sheets and sheet formats Projected views Annotations

8. Editing: Repairs 13. Bottom-up Assembly Modeling ▪ ▪ ▪

Part editing Editing topics Sketch issues

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

9. Editing: Design changes ▪ ▪ ▪ ▪ ▪ ▪

Part Editing Design changes Information from a model Rebuilding tools Replace sketch entity Sketch contours

14. Using Assemblies

10. Configuration ▪ ▪ ▪ ▪ ▪

Configurations Using configurations Other methods to create configurations Modeling strategies for configurations Editing parts that have configurations

11. Global variables and equations ▪ ▪ ▪ ▪ ▪ ▪

Bottom-up assembly Creating a new assembly Position of the first component FeatureManager design tree and symbols Adding components Mating components Using part configurations in assemblies Sub-assemblies Smart Mates Inserting sub-assembies Pack and go

Using global variable and equations Renaming features and dimensions Design rules using global variables and equations Global variable Equations Using operators and functions

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Using assemblies Analyzing the assembly Checking for clearances Changing the values of dimensions Exploded assemblies Explode line sketch Bill of materials Assembly drawing

Appendix ▪ ▪

Options settings Document templates

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 4

Course Outlines for SolidWorks Training - SolidWorks Drawings – 2 Days

1. Drawing Sheets and Views ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Drawing sheets and views Sheets and Formats Terminology Drawing views Sketching in drawing views View settings Centermarks and Centerlines Model Edges in the view

▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪ ▪ ▪

Dimensions Manipulating dimensions Dimension properties

3. Annotations ▪ ▪ ▪

▪ ▪ ▪ ▪

4. Assembly Drawing Views Assembly drawing views Creating views of assemblies

Reusing a drawing file Changing drawing references Using DrawCompare SolidWorks design checker

Appendix

5. Sheet formats and Templates ▪ ▪ ▪ ▪ ▪ ▪ ▪

Performance and display issues Large assembly mode Lightweight drawings Detached drawings Display issues in drawing views

8. Drawing References and Comparison

Adding annotations Annotation types Blocks

.

▪ ▪

Creating and managing a bill of materials The bill of materials Adding a BOM Modifying the BOM Tabulated bill of materials Balloons Design tables in the drawing

7. Performance and Display Issues

2. Dimensions ▪ ▪ ▪

6. Bill of Materials and Tables

▪ ▪

Preparations for detailing Best practices

Sheet formats and templates Drawing templates Properties in the template User Defined properties Customizing a sheet format Define title block Updating Sheet formats

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 5

Course Outlines for SolidWorks Training - SolidWorks Sheet Metal – 2 Days

1. Basic Flange Features ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

3. Additional Sheet Metal Techniques ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

What are sheet metal parts Sheet metal methods Unique sheet metal items Flange method Base flange/tab Sheet metal parameters Editing sheet metal parameters Sheet metal bend features Flat-pattern feature Additional flange features Edge flanges Editing the flange profile Edge flanges on curved edges Miter flanges Hem features Tab features Cuts in sheet metal

4. Converting to Sheet Metal

2. Working with the Flat Pattern ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Working with the flat pattern Flat pattern settings Feature for Manufacture Corner-trim feature Corners in the formed state Closed corner Corner relief Break corner / Corner trim Producing the flat pattern Sheet metal cut list properties Flat pattern drawing views Flat pattern view properties Drawing documents properties Sheet metal tables Cut list properties as a note Exporting the flat pattern

Additional sheet metal methods Designing from the flat Sketch bend feature Jog feature Adding features in an unfold state Unfold and fold Swept flange Swept flange flat pattern options Lofted bends Lofted bends in the design library

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Sheet metal conversion Insert bend method Imported Geometry to Sheet Metal Adding rips Insert bends Making changes Welded corner Converting cones and cylinders Convert to sheet metal

5. Multibody Sheet Metal Parts ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Multibody sheet metal parts Multibodies with base flange Sheet metal parameters for multibodies Cut list item properties for multibodies Flat pattern drawing views for multibodies Cut list balloon annotations Exporting to DXF/DWG with Multibodies Convert with multibodies Hiding and showing bodies Using split with sheet metal parts Patterning for multibodies Using edge flange to merge bodies Interfering bodies Combining sheet metal with other bodies.

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 6

Course Outlines for SolidWorks Training - SolidWorks Sheet Metal – 2 Days (CONTINUED) 6. Forming Tools and Gussets ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪

Sheet metal forming tools Standard forming tools Form tools features in the flat Part document properties Custom form tools Split line Forming tool Form tool in drawing Sheet metal gusset

Tables Customizing Tables K-Factor

9. CutXperts (Tool from SolidXperts)

7. Additional Sheet Metal Functions ▪ ▪ ▪ ▪ ▪ ▪

Appendix A : Sheet Metal Tables

▪ ▪ ▪ ▪

Overview of CutXperts Automatic export in DXF Layers option Options

Additional sheet metal functions Cross-breaks Vent features Mirror part Process plans Sheet Metal Costing

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 7

Course Outlines for SolidWorks Training - SolidWorks Weldments – 1 Day

1. Weldments Features ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

3. Configuring and Detailing Weldments ▪ ▪ ▪ ▪ ▪

Weldments Structural members Groups vs. Structural members Adding plates and holes Gussets and end caps Using symmetry Advantage of a multibody part Limitation of a multibody part

4. Working with Bent Structural Members ▪ ▪

2. Working with Weldments ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Weldment configuration Post-assembly machining features Weldments Drawings Drawing view of individual bodies Representing welds

Working with bent structural members 3D Sketching

Managing the cut list Cut list item names Accessing properties Cut-list properties dialog Structural member properties Adding cut list properties Bounding boxes in weldments Options for generating cut list items Custom structural member profiles Defining material Creating custom profiles Standard of configured profiles Inserting existing parts When to use an assembly

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 8

Course Outlines for SolidWorks Training - SolidWorks Assembly Modeling – 2 Days 1. Advanced Mate Techniques • • • • • • • • • • • • • • • • • •

5. Using Configurations with Assemblies

SolidWorks Assemblies Assembly file structure File references External Reference Search Order Solving Mates Advanced mates Techniques Mate references Design library parts Capture mate references Multiple selection mate references Multiple mate mode Copying multiple components Using Copy with mates Copy with mate options Fixed components Advance mate features Profile center mate Rack and pinion mate

• • • • • • • • • • • •

6. Display states and appearances

2. Top-Down Assembly Modeling • • • • • • • • • • •

Top-down assembly modeling Stage in the process Making changes to dimensions Adding features In-context Inserting a new part into an assembly Building in-context features Propagating changes Saving Virtual parts as external External references Breaking and locking external references Removing external references

3. Assembly Features & Smart Fasteners, and Smart Components • • • •

Assembly features and smart fasteners Assembly features Smart fasteners Smart Components

▪ ▪ ▪ ▪ ▪

Display states Bulk selection tools Advanced select Envelopes Appearances, Materials and scenes

7. Large Assemblies ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Large assemblies Lightweight components Large assembly mode Using SpeedPak Using configurations with large assemblies Defeature Modifying the structure of an assembly Assembly visualisation Large Design Review Tips for faster assemblies Drawing considerations

8. Using SOLIDWORKS Treehouse ▪ ▪ ▪

SOLIDWORKS Treehouse Setting Treehouse instances Exporting Treehouse data

9. Layout-Based Assembly Design

4. Assembly Editing ▪ ▪ ▪ ▪ ▪

Using configurations with assemblies Component patterns Creating configurations manually Configuration properties Using configure component Changing configurations using the context toolbar Assembly evaluation tools Controlling dimensions in an assembly Creating an equality Comments Sensors Using the mate controller

Assembly editing Editing activities Replacing and modifying components Troubleshooting an assembly Replacing components using save as

▪ ▪ ▪ ▪



Layout-based assembly design Blocks Inserting blocks Creating a part from a block Gear and pulley motion in blocks

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 9

Course Outlines for SolidWorks Training - SolidWorks Assembly Modeling – 2 Days (CONTINUED) 1. Advanced Mate Techniques • • • • • • • • • • • • • • • • • •

SolidWorks Assemblies Assembly file structure File references External Reference Search Order Solving Mates Advanced mates Techniques Mate references Design library parts Capture mate references Multiple selection mate references Multiple mate mode Copying multiple components Using Copy with mates Copy with mate options Fixed components Advance mate features Profile center mate Rack and pinion mate

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 10

Course Outlines for SolidWorks Training - SolidWorks Advanced Part Modeling – 2 Days 1. Multibody Solids: How they Work ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Multibody Solids Multibody Techniques Introducing: Solid bodies folder Feature Scope Patterning Bodies Tool Body Introducing: Insert Part Introducing: Move/Copy bodies Combining Bodies

Common Bodies Indent Feature Introducing: Delete Bodies Local Operations Using Cut to Create multibodies Saving solid bodies as parts and assemblies Introducing: Insert into new part Introducing: Save Bodies Splitting a Part into Multibodies Creating an assembly Using split part with legacy data Modelling for Rapid Tooling

3. Sketching With Splines ▪ ▪ ▪ ▪ ▪

Sketching: Splines Introducing: Spline Introducing: Show curvature Combs Sketch Picture Introducing: Sketch Picture

4. Introduction to Sweeping ▪ ▪ ▪

Sweeping Sweep with Guide Curves Sweep Options

5. Working with Curves ▪ ▪ ▪ ▪

Sweeping along a 3D path 3D Sketching Introducing: Helix and Spiral Introducing: Projected Curve

Introducing: Composite curve Introducing: Fit Spline Applying the Label to the Bottle Modeling Threads Sketch Blocks Introducing: Sketch Blocks Equation Driven Curves Introducing: Driven Curve Introducing: Split Line

6. Advance Sweeping

2. Uses of Multi-Body Solids ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪ ▪

Orientation and twist control Align with end faces Sweeping along model edges Sweeping a Tool body

7. Boundary Feature and Lofting ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Why Lofts and Boundary Features How Lofting Works Boundary Feature vs Lofts Using Derived and Copied sketches Copying a sketch Derived sketches Introducing: Insert derived sketch 2-Direction Boundary Feature Layout Sketches Centerline lofting Introducing: Split entities Cleaning up a Model Introducing: Delete face Introducing: Deviation analysis

8. Other Advanced Tools ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Advanced fillets Analyzing Geometry Introducing: Display Curvature Introducing: Intersection Curve Introducing: Zebra Stripes Introducing: Wrap Deform Feature Introducing: Deform Introducing: Knit surface Move face and delete face Introducing: Move Face Performance Consideration

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 11

Course Outlines for SolidWorks Training - SolidWorks Surface Modeling – 2 Days *Training - SolidWorks Advanced Part Modeling is a prerequisite for this class.

1. Understanding Surfaces ▪ ▪ ▪ ▪ ▪

5. Advanced Surface Modeling ▪ ▪ ▪ ▪ ▪

Solids and surfaces Working with surface bodies Why use surfaces Continuity explained Workflow with surfaces

2. Introduction to Surfacing ▪ ▪ ▪

6. Blends and Patches

Similarities between solid and surface modeling Basic surfacing Flattening surfaces

3. Solid-Surface Hybrid Modeling ▪ ▪ ▪ ▪ ▪ ▪ ▪

Stages in the process Ruled surfaces Lofting surfaces Modeling the lower half Design changes

Hybrid modeling Using surfaces to modify solids Interchanging between solids and surfaces Performance implications Surfaces as construction geometry Alternative to Trim Making copies of faces

▪ ▪ ▪ ▪ ▪

Complex blends Smoothing patches Boundary surface Freeform feature Corner blends

7. Master Model Techniques ▪ ▪ ▪ ▪ ▪

Introduction to master models Surface master model technique Working with a solid master model Specialized Features for Plastic Parts SolidWorks Explorer

4. Repairing and Editing Imported Geometry ▪ ▪

Importing data Repairing and editing imported geometry

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 12

Course Outlines for SolidWorks Training - SolidWorks Mold Design – 2 Days *Training - SolidWorks Advanced Part Modeling is a prerequisite for this class. **Training - SolidWorks Surface Modeling is recommended

1. Surface Concepts and Imported Geometry ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪



Importing data 3D Model types Definitions Terminology File translators Modeling systems File translation Why do imports fail? Diagnosis and repair Checking solid bodies Making copies of faces Repairing gaps Repairing faces

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Core and cavity mold design SolidWorks mold tools Mold analysis tools Analyzing draft on a model Draft analysis colors Scale the part to allow for shrinkage Establish the parting lines Manual selection of parting lines Automation Modeling the parting surface Smoothing the parting surface Surface bodies Interlocking the mold tooling Creating the mold tooling

2. Side Cores and EDM Design ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Parting lines and shut-off surfaces Draft analysis options Parting line options Core and cavity surfaces Shut-off surfaces Parting Surface Tooling split Seeing inside the mold

5. Using Surfaces for Model Prep and Interlocks

1. Core and Cavity ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

4. Advanced Parting Lines, Shut-Off Surfaces and Cores

▪ ▪ ▪

Surfaces in mold making Creating new drafted faces Interlock surfaces

6. Using Surfaces for Mold Design Features ▪ ▪

The mixer Mold split folders

7. Alternate Methods for Mold Design ▪ ▪ ▪ ▪ ▪ ▪ ▪

Alternate methods for mold design Using Combine and split Creating a cavity Using surfaces Using the up to surface method Using the split method Manually creating shut-off surfaces

Multiple parting directions Trapped molding areas Side cores Feature Freeze Lifters Core Pins Electrode clearances Keeping the sharp edges

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 13

Course Outlines for SolidWorks Training - SolidWorks Mold Design – 2 Days *Training - SolidWorks Advanced Part Modeling is a prerequisite for this class. **Training - SolidWorks Surface Modeling is recommended

(CONTINUED) 8. Reusable Data ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Reusing data Task pane SolidWorks Resources Design library Files Explorer Library features Configurations in library features Smart component

9. Completing the Mold Base ▪ ▪ ▪ ▪ ▪ ▪



Organizing the Assembly Modifying the lifters Ejector pins Cooling the mold Making the drawing Making changes Completing the process

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 14

Course Outlines for SolidWorks Training - SolidWorks Routing: Piping and Tubing – 2 Days



1. Fundamentals of Routing ▪ ▪ ▪ ▪

6. Creating Routing Components

What is Routing? Routing setup Routing Library manager General Routing settings

2. Piping Routes ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Piping routes Pipes and piping components Routing Assembly Templates Creating a piping route Auto Route Route Specification Template Editing a Route Routing Along Existing Geometry

3. Piping Fittings ▪ ▪ ▪

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Routing library parts Libraries Creating Routing library parts Pipe & Tube Components Copying routing components Routing Library manager Fitting Components Routing functionality points Routing Geometry Part Validity Check Design Table Check Component Attributes Elbow Components Multi-body components Valve components

7. Using P&ID Files

Piping Fittings Drag and Drop a Fitting Creating Custom Fittings

4. Tubing Routes ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Piping Drawings

Tubing routes Tubes and tubing components Flexible tubing with auto route Orthogonal tubing routes with auto route Bend and Spline Errors Starting a tube route on the fly Making Tubes Repairing a Bend Errors Tubing Drawings

▪ ▪ ▪ ▪ ▪

Piping and instrumentation Adding a pipe Pipe with multiple lines Pipe with In-Line Fittings Process drawings

8. Electrical Ducting, Cable Tray, and HVAC Routes ▪ ▪ ▪

Electrical Ducting routes Cable tray routes HVAC routes

9. Piping Skids 5. Piping and Tubing Changes ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Piping and Tubing Changes Pipe Penetrations Flange to flange Connections Pipe Spools Copying Routes Adding Slope Editing Piping Routes Editing for Obstructions

▪ ▪ ▪ ▪ ▪

Piping Skids Grid system feature Weldments Walk-through animations Avatar paths

10. Using SolidWorks content ▪

Using SolidWorks content

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 15

Course Outlines for SolidWorks Training - SolidWorks What's New – 1 Day

1. Welcome to SOLIDWORKS 2016 ▪ ▪ ▪



Highlights Top Enhancements Performance Improvements

2. User Interface ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

User Interface Redesign Improved User Interface Scaling for HighResolution Screens New Icon Style Redesigned Triad Analysis Preparation CommandManager Expandable PropertyManager Input Boxes FeatureManager Design Tree Filter Performance Hiding and Showing Primary Planes Keyboard Input in PropertyManagers Menu Consolidation Moving the Confirmation Corner Options to the Pointer Persistent Context Toolbar When Sketching Selection Breadcrumbs Toolbar and CommandManager Docking Behavior Undo Location on Mate Context Toolbar Visualization Tool for References

3. SolidWorks Fundamentals ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

4. Assemblies

3D ContentCentral 3D Printing Enhancements - Preview 3D Printing Enhancements - Settings Active Content Warnings Application Programming Interface Improved SOLIDWORKS Error Report Dialog Box Property Tab Builder Conditional Lists Quick Tip Removal Replacing Equation References for Deleted Features Saved Dialog Box Modifications Searching MySolidWorks Task Scheduler Print Enhancements

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Choosing a Configuration While Adding a Component Component Selection Enhancements Copying Multiple Components Mates Mirroring Assembly Features Pattern Driven Component Pattern Improvements Performance Evaluation (Formerly AssemblyXpert) Purging Unused Features Remove All Appearances Renaming Components in the FeatureManager Design Tree Replacing Subassemblies with Multibody Parts Subassemblies Temporarily Fix Components with a Separate Tool Toggling the Visibility of Bodies

5. Detailing and Drawings ▪ ▪ ▪ ▪ ▪ ▪

Dimensions Drawing Views Model Detailing Notes and Balloons Performance Sheets

6. Model Display ▪ ▪ ▪ ▪ ▪ ▪

Callout Improvements Cartoon Rendering in RealView PhotoView 360 Rendering Improvements Parallel Tessellation When Regenerating Assembly Graphics Preserving Appearances with Derived Parts Section View Offset Options

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 16

Course Outlines for SolidWorks Training - SolidWorks What's New – 1 Day (CONTINUED) 7. Parts and Features ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Create ANSI Inch Holes with FeatureWorks and Direct Editing Curvature Continuous Edge Fillets Dynamic Preview for Intersect and Mutual Trim Tools Maintain Hole Wizard Settings When Changing Type Options for Modifying Geometry with the Intersect Tool Patterns Reference Geometry Surfaces Sweep Thread Toggling the Visibility of Bodies

8. Sheet Metal ▪ ▪ ▪

9. Sketching

Cuts in Swept Flanges Edge Flanges Using Flattened Mass

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Cap Ends for Offset Entities Converting Entities with Internal Loops Equal Curve Length Parametric Relations Instant2D for Changing Sketch Dimensions Preselection of Entities for Smart Dimensioning Reversing Sketch Offsets Segment Tool Selecting Midpoints with Dynamic Highlighting Show or Hide Sketch Dimensions Style Spline Support for B-Splines Unmerging Sketch Endpoints with Detach Segment on Drag Improvement in Large Sketch Performance

10. Weldments ▪ ▪ ▪ ▪ ▪

Modifying End Cap Positions Using Reference Dimensions Structural Member Feature Names Structural Member Size Lists Total Length for Derived Parts Transferring Material Properties from Library Profiles

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 17

Course Outlines for SolidWorks Training - SolidWorks Conceptual Design – 3 Days 1. Introduction to the 3DEXPERIENCE Platform ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

The 3DEXPERIENCE Platform Accessing the Platform Related Apps Getting Starting with the 3DEXPERIENCE Platform Accessing SOLIDWORKS Mechanical Conceptual Unique Concepts Collaboration Tools Video Tutorials

2. Introduction to the User Interface ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Exploring the SOLIDWORKS Mechanical Conceptual User Interface Compass Top Bar Search 6W Tags Services Tabs Design Tree Action Bar Work Area Task Panel Help Resources

3. Basic Modeling ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Fillets and Rounds Selection Helper Shelling Editing Topics Editing Features and Sketches Hole Thread Importing SOLIDWORKS Files Color Measure

5. Data Management and Option ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Customizing SOLIDWORKS Mechanical Conceptual Preferences Mechanical Conceptual Preferences General Preferences Configure Tool Customizing the Action Bar Managing Data Successful Searching Concept Archives Manage Action Bar Share Services Save with Options Importing 3D XML Files Using Share Lock and Unlock 3DInstant Messaging Export Options Importing Data

6. 2D Motion

Basic Modeling Physical Products Sketching Dimensioning Inferences Sketch Constraints Sketch Booleans Extrude Renaming Objects Saving the Physical Product Product Views Custom Views

4. Adding and Editing Features ▪

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

2D Motion Mechanism Mode Slot Instant Motion Motion Study Traced Path Clash Alert Kinematic Contact Plots Using Mechanical Constraints Make Rigid Sketch Symmetry Rotary and Linear Motion

Adding and Editing Features

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 18

Course Outlines for SolidWorks Training – SolidWorks Conceptual Design – 3 Days (CONTINUED) 7. 3D Motion ▪ ▪ ▪ ▪

10. Top Down Layouts

3D Motion Components in the Design Tree Product Visibility Springs

8. Bottom Up Design - Existing Geometry ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪



Single Modeling Environment Single Modeling Environment Workflows Physical Product Part Bottom Up Assembly Design Top Down Assembly Design Master Model Design Single Modeling Environment Workflow Comparisons Bottom Up Assembly Design Inserting Existing Components Floating and Fixing Components Moving and Rotating Components Adding Mates Auto Mates Component Operations

9. Creating Bottom Up Components ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Creating Bottom Up Components Primitive Components Activating a Component Reference Items Feature Patterns Creating Components Revolve Swept Volume

▪ ▪ ▪ ▪ ▪ ▪

Creating Top Down Layouts Sketch To Components Developing the Components Adding Geometry With Links Creating In-Context Components Insert New Component

11. Using Master Models ▪ ▪ ▪ ▪

Using Master Models Multiple Bodies Merge Settings Master Model

12. Assembly Tools ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Assembly Tools Product Structure Explode View Bill of Materials Component Patterns Interference Detection Replacing Components in an Assembly Replace Component Copy With Mates Traced Drag

13. Direct Editing ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Direct Editing Direct Edit Face Options Direct Editing Constraints and Dimensions Other Direct Edit Tools Using Direct Edit With a Physical Product Mass Properties Sensors Material Palette

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 19

Course Outlines for SolidWorks Training - SolidWorks Industrial Design – 2 Days 1. The 3DEXPERIENCE Platform ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

The 3DEXPERIENCE Platform Accessing the Platform Accessing Apps 3DDashboard: Gateway to the Platform Application User Interface Roles and Related Applications Data within the Tenant 3DSwym Creating a Swym Community Adding Content to a Swym Community Creating a Blog Post Other Swym Functions 3DSpace Creating a Collaborative Space Additional 3DSpace Functions Content on the 3DDashboard Customizing the Dashboard Widget Functions Tab and Dashboard Functions SOLIDWORKS Industrial Design Unique Concepts Putting it All Together

2. SWID User Interface ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Exploring the Industrial Design User Interface Search Filter SWID Service Buttons Product Tabs Work Area Design Tree Bread Crumbs Task Panel Action Bar Context Toolbars and Menus Dialog Boxes Mouse Gestures Mouse Buttons View Manipulation with the Keyboard Swap Visibility

3. Basic Sketching ▪ ▪ ▪

Concept Development Creating New Physical Product What is a Sketch?

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Creating a New Sketch Sketch Tools Sketch Action Bar Desk Layout Canceling a Sketch Tool Defining a Sketch Sketch Constraints Dimensions Modifying Dimensions Rigid Sketch Objects Information in the Design Tree Sketch Object Propertie Combining Sketch Objects Design Intent Sketch Fillets Construction Geometry Sketching Lines Copying Sketch Objects Completing a Sketch Editing a Sketch Saving Products Publishing Designs to Swym 3D XML FilesCustom Views

4. SWID Options and Data Management ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

SWID Options and Data Management Basics of Assembly versus Part Products Modifying Preferences General Preferences Industrial Design Preferences Customizing Keyboard Shortcuts and Mouse Gestures Managing Data Successful Searching Search Results Window Using 6W Tags Defining Favorites Attributes Sharing to a Collaborative Space Locking and Unlocking Products Save with Options - Part Product Local Save Exporting Products Importing Products Sharing through 3DMessaging Modifying Assembly Components

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 20

Course Outlines for SolidWorks Training – SolidWorks Industrial Design – 3 Days (CONTINUED) 5. Concept Sketching ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

7. Advanced Freeforms

Concept Sketching Changing Curve Appearance Smooth Curves Deleting Curves Using Primitive Lines and Arcs Sketching with Touch Enabled Devices Contour Curves Trim Utility Using Concept Curves for Features Converting Concept to Contour 3D Sketches Trimming Surfaces Extending Surfaces Combining Multiple Surface Bodies Adding Fillets Contour Curves for Mechanical Features Revolve Extrude Feature

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Advanced Freeform Shapes Symmetric Concept Sketches Selection Filters Mesh Cage Aligning Mesh Points Adding and Removing Edge Loops Extending Faces and Creating Holes Sharp Edges Combining Multiple Freeform Shapes Mechanical Features Moving Solid or Surface Bodies Combining the Bodies Additional Freeform Shapes Splitting Subdivision Faces Shell Feature

6. Freeform Shapes ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Subdivision Modeling 2D Freeform Shapes 3D Freeform Shapes Modifying the Shape Finishing the Freeform Applying Material Publishing Images Setting the Lighting Preparing the Output Image Rendering the Image Further Customizing the View Bending a Freeform

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 21

Course Outlines for SolidWorks

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 22

SOLIDWORKS SIMULATION COURSE OUTLINE

Simulation training index Training - SolidWorks Simulation Static – 3 days .................................................................................... 24 Training - SolidWorks Motion – 2 days ...................................................................................................... 25 Training - SolidWorks Simulation Standard – 2 Days .............................................................................. 26 Training - SolidWorks Simulation Professional – 1 Day .......................................................................... 28 Training - SolidWorks Simulation Premium – 2 Days .............................................................................. 29 Training - SolidWorks Simulation Premium Composite – 1 Day ............................................................ 30 Training - SolidWorks Flow Simulation – 2 Days ..................................................................................... 31 Training - SolidWorks Flow Simulation: Electronic Cooling Module – 1 Day ....................................... 32 Training - SolidWorks Flow Simulation: HVAC Module – 1 Day ............................................................. 33 Training - SolidWorks Plastics 1.5, 2 or 3 Days ........................................................................................ 34 Training - SolidWorks Sustainability– 1 Day............................................................................................. 36

Page 23

Course Outline for Simulation Training - SolidWorks Simulation Static – 3 days ▪ ▪ ▪ ▪

1. The Analysis Process ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

The Analysis Process SolidWorks simulation options Preprocessing Meshing Processing Post-processing Multiple studies Reports

8. Mixed Meshing Shells & Solids ▪

2. Mesh Controls, Stress Concentrations and Boundary Conditions ▪



Mesh control Understanding the effect of boundary conditions

3. Assembly Analysis with Contacts ▪ ▪ ▪

Contact analysis Pliers with global contact Pliers with local contact

9. Beam Elements – Analysis of a conveyor frame ▪

Beam and truss elements

10. Mixed Meshing Solids, Beams & Shells ▪ ▪

Mixed meshing Beam Imprint

▪ ▪ ▪

Design study Part 1: multiple load cases Part 2: Geometry modification

12. Thermal Stress Analysis

Shrink fit parts Analysis with soft springs

5. Assembly Analysis with Connectors and Mesh Refinement ▪ ▪ ▪ ▪ ▪ ▪

Mixed meshing solids and shells

11. Design Study

4.Symmetrical and Free Self-Equilibrated Assemblies ▪ ▪

Solid vs. shell Creating shell elements Part 3: shell elements – mid plane surface Results Comparison

Connecting components Connectors Mesh Control in an Assembly Problem statement Part 1: Draft quality coarse mesh analysis Part 2: High quality mesh analysis

▪ ▪ ▪

Thermal stress analysis Examining results in local coordinate systems (optional) Saving models in its deformed shape

13. Adaptive Meshing ▪ ▪ ▪ ▪

Adaptive meshing H-adaptivity study P-Adaptivity study H vs P elements – summary

14. Large Displacement Analysis 6. Compatible/ Incompatible Mesh ▪

Compatible /incompatible meshing

▪ ▪



Small vs Large displacement analysis Part 1: small displacement linear analysis Part 2: Large displacement non-linear analysis

7. Analysis of Thin Components ▪ ▪

Thin components Part 1: Mesh with solid elements



Part 2: Refined solid mesh

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 24

Course Outline for Simulation Training - SolidWorks Motion – 2 days

1. Introduction to Motion Simulation and Forces ▪ ▪ ▪

Basic motion analysis Forces Results

Creating local mates Mates Local mates Power Plotting kinematic results

Contact and friction Contact Contact groups Contact friction Translational spring Translational damper Post-processing Analysis with friction (optional)



Motion Optimisation Sensors Optimisation analysis

Flexible joints System with Flexible Joints

9. Redundancies ▪ ▪ ▪

Redundancies How to check for redundancies Typical redundant mechanisms

10. Export to FEA ▪ ▪ ▪

Exporting results Export of load Direct solution in SolidWorks motion

11. Event Based Simulation

Contact forces STEP function Contact: Solid bodies Geometrical description of contacts Instability points Modifying result plots Precise contact Integrators

5. Curve to Curve Contact ▪ ▪ ▪

▪ ▪ ▪

▪ ▪

4. Advanced Contact ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

CAM’s Trace path Exporting trace path curves

8. Flexible Joints

3. Introduction to Contacts, Springs and Dampers ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪

7. Motion Optimisation

2. Building a Motion Model and Post Processing ▪ ▪ ▪ ▪ ▪

6. CAM synthesis

Contact forces Curve to curve contact Solid bodies vs. Curve to curve contact Solid bodies contact solution

▪ ▪ ▪ ▪

Event based simulation Servo motors Sensors Task

12. Design Projects (Optional) ▪ ▪ ▪ ▪ ▪ ▪

Design Project Self-guided problem – Part 1 Self-guided problem – Part 2 Problem solution – Part 1 Creating the force function Force expression

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 25

Course Outline for Simulation Training - SolidWorks Simulation Standard – 2 Days •

*Training - SolidWorks Simulation Static is a prerequisite for this class.

1. Introduction to Motion Simulation and Forces ▪ ▪ ▪

Basic motion analysis Forces Results

Creating local mates Mates Local mates Power Plotting kinematic results



Motion Optimisation Sensor Optimisation analysis

Flexible joints System with Flexible Joints

9. Redundancies ▪ ▪ ▪

Contact and friction Contact Contact groups Contact friction Translational spring Translational damper Post-processing Analysis with friction (optional)

Redundancies How to check for redundancies Typical redundant mechanisms

10. Export to FEA ▪ ▪ ▪

Exporting results Export of load Direct solution in SolidWorks motion

11. Event Based Simulation

Contact forces STEP function Contact: Solid bodies Geometrical description of contacts Instability points Modifying result plots Precise contact Integrators

▪ ▪ ▪ ▪

Event based simulation Servo motors Sensors Task

12. Design Projects (Optional)

5. Curve to Curve Contact ▪ ▪ ▪

▪ ▪ ▪

▪ ▪

4. Advanced Contact ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

CAM’s Trace path Exporting trace path curves

8. Flexible Joints

3. Introduction to Contacts, Springs and Dampers ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪

7. Motion Optimisation

2. Building a Motion Model and Post Processing ▪ ▪ ▪ ▪ ▪

6. CAM synthesis

Contact forces Curve to curve contact Solid bodies vs. Curve to curve contact Solid bodies contact solution

▪ ▪ ▪ ▪ ▪ ▪

Design Project Self guided problem – Part 1 Self guided problem – Part 2 Problem solution – Part 1 Creating the force function Force expression

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 26

Course Outline for Simulation Training - SolidWorks Simulation Standard – 2 Days (Continued) *Training - SolidWorks Simulation Static is a prerequisite for this class.



13. Fatigue Analysis ▪ ▪ ▪ ▪ ▪ ▪ ▪

Fatigue Stress-life (S-N) based fatigue Thermal study Thermal stress study Fatigue terminology Fatigue study Fatigue study with dead load (optional)

14. Variable Amplitude Fatigue ▪

Fatigue study

15. Trend Tracker ▪ ▪ ▪ ▪ ▪ ▪ ▪

Trend Tracker Overview Trend Journal Tracked Data Graph Trend Tracker Gallery Restoring Trend Tracker Iterations Add Trend Tracker Iterations Delete Trend Tracker Iterations

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 27

Course Outline for Simulation Training - SolidWorks Simulation Professional – 1 Day *Training - SolidWorks Simulation Static is a prerequisite for this class.

1. Frequency Analysis of Parts ▪ ▪ ▪ ▪

Modal analysis basics Frequency analysis with supports Frequency analysis without supports Frequency analysis with load

2. Frequency Analysis of Assemblies ▪ ▪

All bonded contact conditions Bonded and allow penetration contacts

3. Buckling Analysis ▪

▪ ▪

9. Fatigue Analysis ▪ ▪ ▪ ▪ ▪ ▪ ▪

10. Variable Amplitude Fatigue

4. Load Cases

11. Drop Test Analysis ▪ ▪ ▪ ▪ ▪

Submodeling

6. Thermal Analysis ▪ ▪ ▪ ▪ ▪

Drop test analysis Rigid floor drop test Elastic floor, Elasto-Plastic Material Elasto-plastic material model Drop test with contact (optional)

12. Optimization Analysis

Thermal analysis basics Steady – state thermal analysis Transient thermal analysis Transient analysis with time varying load Transient thermal analysis using a Thermostat

7. Thermal Analysis with Radiation ▪

Fatigue study

Load Cases

5. Submodeling ▪

Fatigue Stress-life (S-N) based fatigue Thermal study Thermal stress study Fatigue terminology Fatigue study Fatigue study with dead load (optional)

Buckling analysis ▪



3D model Microchip Testing Assembly

▪ ▪

Optimization analysis Static and frequency analyses

13. Pressure Vessel Analysis ▪ ▪

Pressure vessel analysis Manhole nozzle flange and cover

Steady state analysis

8. Advanced Thermal Stress 2D Simplification ▪ ▪

Thermal stress analysis Thermal analysis

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 28

Course Outline for Simulation Training - SolidWorks Simulation Premium – 2 Days *Training - SolidWorks Simulation Static and Training - SolidWorks Simulation Professional is a prerequisite for this class.

8. Metal Forming

NON-LINEAR 1. Large Displacement Analysis ▪ ▪ ▪

Linear static analysis Nonlinear static study Linear static study (Large displacement)

2. Incremental ▪ ▪ ▪ ▪

Control Techniques

Incremental control techniques Linear analysis Nonlinear analysis – Force control Nonlinear analysis – Displacement control

3. Non-Linear Static Buckling Analysis ▪ ▪ ▪ ▪

Linear buckling Linear static study Nonlinear symmetrical buckling Nonlinear asymmetrical buckling

4. Plastic Deformation ▪ ▪ ▪ ▪ ▪ ▪

DYNAMIC 1. Vibration of a Pipe ▪ ▪ ▪ ▪

Static analysis Frequency analysis Dynamic analysis (slow force) Dynamic analysis (Fast force)

2. Transient Shock Analysis According to MILS- STD-810G ▪

Model with remote mass

3. Harmonic Analysis of a Bracket ▪

▪ ▪

Harmonic analysis of a bracket

Response Spectrum Analysis Response Spectrum

5. Random Vibration Analysis According to MIL-STD-810G ▪

Hardening rules Isotropic hardening Kinematic hardening

Random vibration analysis according to MIL-STD810G

6. Non-Linear Dynamic Analysis of an Electronic Enclosure

6. Analysis of Elastomers ▪ ▪ ▪ ▪

Bending

4. Response Spectrum Analysis

Plastic deformation Problem statement Linear elastic Nonlinear – von Mises Nonlinear – Tresca’s Non-linear Elastic Material

5. Hardening Rules ▪ ▪ ▪



Two constant Mooney-Rivlin (1 material curve) Two constant Mooney-Rivlin (2 material curves) Two constant Mooney-Rivlin (3 material curves) Six constant Mooney-Rivlin (3 material curves)

▪ ▪

Linear dynamic analysis Nonlinear dynamic analysis

7. Non Linear Contact Analysis



Problem statement

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 29

Course Outline for Simulation Training - SolidWorks Simulation Premium Composite – 1 Day *Training - SolidWorks Simulation Static and Training - SolidWorks Simulation Professional is a prerequisite for this class.

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Introduction to Composites Objectives Composite Materials Composite Lamina Composite Laminate SolidWorks Simulation Premium: Composites Composite Post Processing Case Study: Mountain Board Project Description Stages in the Process Lamina Properties Experimental Measurements Micromechanics

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Required Parameters Strength Parameters Composite Options Composite Orientation Offset Shell Alignment Composite Post Processing Stresses Inter Laminar Shear Failure Criterion Shear Stresses Summary Reference

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 30

Course Outline for Simulation Training - SolidWorks Flow Simulation – 2 Days

1. Creating a SolidWorks Flow Simulation Project ▪ ▪

Model preparation Post-Processing

Computational mesh Basic mesh Initial mesh Geometry resolution Optimize thin wall resolution Result resolution / Level of initial mesh Control planes

3. Thermal Analysis ▪ ▪

▪ ▪

▪ ▪ ▪

9. Parametric Analysis ▪ ▪



Fans Perforated plates

Reynolds number External flow Transient analysis Turbulence intensity Solution adaptive mesh refinement Two dimensional Flow Computational domain Calculation control options Time animation

5. Conjugate Heat Transfer Conjugate Heat Transfer Real Gases

Parametric analysis Steady state analysis

Cavitation

11. Relative Humidity ▪

▪ ▪

Rotating reference frame Tangential faces of rotors Time step

10. Cavitations

4. External Transient Analysis ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Porous media Design modification

8. Rotating Reference Frames

2. Meshing ▪ ▪ ▪ ▪ ▪ ▪ ▪

7. Porous Media

Relative humidity

12. Particle Trajectory ▪

Particle trajectories

13. Supersonic Flow ▪

Supersonic flow

14. FEA Load Transfer ▪

FEA Load Transfer

6. EFD Zooming ▪

EFD zooming

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 31

Course Outline for Simulation Training - SolidWorks Flow Simulation: Electronic Cooling Module – 1 Day *Training - SolidWorks Flow Simulation is a prerequisite for this class.

1. Introduction to Electronics Module ▪ ▪ ▪ ▪ ▪

Objectives Electronic Module Case Study: Computer Box Project Description Conclusions

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 32

Course Outline for Simulation

Training - SolidWorks Flow Simulation: HVAC Module – 1 Day *Training - SolidWorks Flow Simulation is a prerequisite for this class.

1. Introduction to HVAC ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪



Objectives HVAC Module Case Study: Office Project Description Radiation Radiation Transparency Radiation Source Radiative Surface Discussion Comfort Parameters Conclusions

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 33

Course Outline for Simulation

Training - SolidWorks Plastics 1.5, 2 or 3 Days *The SolidWorks Plastics training manual covers all the features and functions of the SolidWorks Plastics application. Lessons 1 through 8 cover the features of SolidWorks Plastics Standard (1.5 day). Lessons 1 through 14 cover the features of SolidWorks Plastics Professional (2 day) Lessons 1 through 19 cover the features of SolidWorks Plastics Premium (3 day).

1. Basic Flow Analysis ▪ ▪ ▪ ▪ ▪ ▪ ▪



7. Detecting Air Traps ▪ ▪ ▪

Basic Flow Analysis Element Types Meshing The PlasticsManager Tree Material Injection Location Running a Flow Analysis Flow Results

8. Gate Blush ▪ ▪

2. Detecting Short Shots ▪ ▪ ▪

Detecting Short Shots Fill Settings Flow Front Central Temperature

▪ ▪ ▪ ▪ ▪ ▪ ▪

Automation Tools Duplicate Study Copying Settings Batch Manager

Injection Locations and Sink Marks Injection Location Rules Sink Marks

5. Materials ▪ ▪ ▪ ▪ ▪ ▪ ▪

Materials Properties User-Defined Database Resin Properties Heat Transfer Properties Viscosity PCT Data Mechanical Properties

6. Mesh Manipulation ▪ ▪ ▪ ▪ ▪ ▪

Local Refinement of Mesh Element Issues Mesh Editing Leader Lines Solid Mesh Solid Mesh types

Pack and Cooling Flow/Pack Switch Pack Stage Pack Analysis Pack Results X-Y Plot CoolingTimes

10. Reducing Cooling Times

4. Injection Locations and Sink Marks ▪ ▪ ▪

Gate Blush Runner Elements

9. Packing and Cooling Times

3. Automation Tools ▪ ▪ ▪ ▪

Detecting Air Traps Air Traps Venting

▪ ▪

Reducing Cooling Time Multiple Injection Locations

11. Multiple Cavity Molds ▪ ▪ ▪ ▪ ▪ ▪ ▪

Multiple Cavity Molds Mold Layouts Channel Design Runner Channel Design Runner Wizard Channel Design Family Mold Layout Using Runner-Balancing

12. Symmetry Analysis ▪ ▪

Symmetry Analysis Symmetry Face

13. Valve Gates and Hot Runners ▪ ▪ ▪

Valve Gates and Hot Runners Hot Runners Valve Gates

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 34

Course Outline for Simulation

Training - SolidWorks Plastics 1.5, 2 or 3 Days (Continued) *The SolidWorks Plastics training manual covers all the features and functions of the SolidWorks Plastics application. Lessons 1 through 8 cover the features of SolidWorks Plastics Standard (1.5 day). Lessons 1 through 14 cover the features of SolidWorks Plastics Professional (2 day) Lessons 1 through 19 cover the features of SolidWorks Plastics Premium (3 day).

14. Reaction Injection Molding ▪

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Reaction Injection Molding

15. Using Inserts ▪ ▪ ▪

Using inserts Cavities and Inserts Materials for Inserts

16. Multi Shot Mold ▪

Multi Shot Mold

Using Inserts Gas Assist

Cooling Analysis Cooling Cooling Channels and Mold Bodies Coolant Mold Cool Settings Cooling Simulations Cool Analysis Cool Results Baffle Bubbler

19. Warpage Analysis

17. Gas Assistance Molding ▪ ▪

18. Cooling Analysis

▪ ▪ ▪ ▪ ▪

Warpage Analysis Shrinkage Warpage Warp Settings Flow, Pack and Warp Analysis

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 35

Course Outline for Simulation

Training - SolidWorks Sustainability– 1 Day

1. SustainabilityXpress ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Evaluating the Environmental Impact of a Part Selecting a Material Using the Find Similar Material Tool Setting the Manufacturing Options Setting Use Options Using the Environmental Impact Dashboard Impact Assessment Methodologies Creating a Report Exporting Settings for a SolidWorks Sustainability Study Adding Materials Updating the Materials Database

2. SolidWorks Sustainability ▪ ▪ ▪ ▪ ▪ ▪ ▪

SolidWorks Sustainability Overview Sustainability Task Pane Views Evaluating the Environmental Impact of a Part Selecting a Material Using the Find Similar Material Tool Setting the Manufacturing Options Setting Use Options

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Using the Environmental Impact Dashboard Impact Assessment Methodologies Creating a Report Exporting Settings for a SolidWorks Sustainability Study Evaluating the Environmental Impact of an Assembly Preparing the Assembly to Be Evaluated Defining the Assembly Process Specifying Assembly Use Parameters Modifying Transportation Defaults Modifying End of Life Disposal Defaults Specifying Duration of Use Modifying Components Adding Materials Adding Sustainability Data to a Custom Material Assigning Financial Impact to a Custom Material Updating the Materials Database Requesting Materials Visualizing Sustainability Properties

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 36

DATE MANGEMENT COURSE OUTLINE

PDM training index Training - PDM Administration – 2 Days ........................................................................................ 38 Training - Using SolidWorks PDM – 1 Day ..................................................................................... 39 Training - PDM API Fundamentals – 2 Days .................................................................................. 40

Page 37

Course Outline PDM Training - PDM Administration – 2 Days

1. Installation planning ▪ ▪ ▪ ▪

6. Column and Bill of Materials

Planning for SolidWorks PDM The planning process Training scenario The installation process

2. The Administration Tool ▪ ▪ ▪ ▪

SolidWorks Enterprise PDM administrative tool Creating a SolidWorks file Vault Create a local file vault view Setup overview

▪ ▪

Columns Bill of materials

7. Workflow ▪ ▪ ▪

Workflows Categories Revisions

8. Notifications and Task ▪ ▪

Notifications Tasks

3. Users and Groups ▪ ▪

Users Groups

4. Folder Card creation ▪ ▪

Data Cards Anatomy of a Data Card

5. File and Search Cards ▪

Importing data cards

9. Folder Templates ▪

Templates

10. File Templates ▪ ▪

File Templates Templates with Other File Types

11. Data Migration ▪ ▪

Migrating Legacy Data Migrating Revisions

12. Vault Backup ▪

Backing Up File Vaults

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 38

Course Outline PDM Training - Using SolidWorks PDM – 1 Day

1. SolidWorks Enterprise PDM Concepts ▪ ▪ ▪ ▪ ▪

The fundamentals of PDM What is SolidWorks PDM? SolidWorks PDM Overview SolidWorks PDM Modules SolidWorks PDM Components

2. SolidWorks Enterprise PDM User Interface

5. File references ▪

6.Searching ▪

Searching SolidWorks PDM

7. Workflow and notification ▪



File references

SolidWorks PDM Workflow

SolidWorks PDM user interface

8. Working in SolidWorks 3. Document Creation and Check In ▪ ▪

Document creation and check in Advanced document check in

▪ ▪

Versioning SOLIDWORKS files Managing local cache

9. Appendix A 4. Versioning files ▪



Bill of materials (BOM)

Versioning files

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 39

Course Outline PDM Training - PDM API Fundamentals – 2 Days

1. Connecting to a Vault ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

5. Add-In Applications

COM Programming Application Types Namespaces The IEdmVault Interface Debugger feedback Logging into a Vault Handling HRESULT Return Values SOLIDWORKS PDM Pofessional API Help Interface Versioning

2. Files, Folders, Items and References ▪ ▪ ▪ ▪ ▪ ▪ ▪

The IEdm Object Interface The IEdm File Interface The IEdm Folder Interface The IEdm Pos Interface File References The IEdm Batch-Listening Interface The IEdm Clear-Local Cache Interface

3. Users and Groups ▪ ▪ ▪

The IEdm User Interface The IEdm User Group Interface The IEdm UserMgr Interface

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

SolidWorks Enterprise PDM Add-Ins The IEdm AddIn Interface The Implements Statement Simple Implementation COM Registration Get AddIn Info Minimum Version Required Additional Add-In Information Installing an Add_in Debugging a DLL The IEDm Vault Argument The IEDm CmdMGR Argument The IEDm AddIn 5. OnCmd EdmCmdData Members for EdmCmd EdmCmdData Members for EdmCmd_Serial No

6. Task Add-In Applications ▪ ▪ ▪ ▪ ▪ ▪

SolidWorks Enterprise PDM Task Add-Ins Task Interfaces Task Hooks The IEdm Search Interface The IEdm Workflow Mgr Interface The IEdm Workflow Interface

4. Card Variables, Versions and Revisions ▪ ▪ ▪ ▪

Card Variables File Versions File Revisions The IEdm Dictionary Interface

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 40

SOLIDWORKS COMPOSER COURSE OUTLINE

Composer training index Training - SolidWorks Composer – 3 Days .................................................................................... 42

Page 41

Course Outline for Composer Training - SolidWorks Composer – 3 Days

1. Getting started ▪ ▪ ▪ ▪ ▪ ▪

6. Creating a Marketing Image

What is the Composer application? Starting Composer SolidWorks Composer terminology SolidWorks Composer user interface Preferences and Document Properties Creating 2D output

2. Creating Cover and Detail Images ▪ ▪ ▪ ▪ ▪ ▪

Views Rendering tools Navigation Tools Camera and Alignment tools Create 2D output Digger

Selections Textures Lighting High Resolution

7. Creating an Animations ▪ ▪

Timeline Pane Position Key

8. Creating Interactive Content

3. Creating an Exploded View ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪ ▪

Visibility tools Exploded View Collaborative Actors Styles Vector Graphics Output

▪ ▪ ▪ ▪ ▪ ▪

Selections in the Key Track Position and Property Keys Filters Animating and Collaborative Actors Digger keys Events

9. Creating a Walkthrough Animation ▪ ▪ ▪

Camera Keys Adding Views to the Timeline Grids

4. Creating Additional Exploded Views ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Paper Space Importing Files File Types Update views With Selected Actors Align Actors Explode Lines Custom Views Linking Between Views

5. Creating Bill of Materials ▪ ▪ ▪

Bill of Materials Vector Graphic Output Another BOM Table

10. Creating an Explode and Collapse Animation ▪ ▪

Assembly Selection Mode Scenarios

11. Updating Composer Files ▪ ▪

Update an Entire Assembly Changing the Geometry of an Actor

12. Publishing from Composer ▪

Preparing a File for Publishing

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 42

SOLIDWORKS ELECTRICAL COURSE OUTLINE

Electrical training index Training - SolidWorks Electrical: Schematic – 2 Days .................................................................. 44 Training - SolidWorks Electrical: 3D – 1 Day ................................................................................. 46 Training – SolidWorks Electrical Advanced – 1 Day ..................................................................... 47 Training - SolidWorks Routing: Electrical – 1 Day ........................................................................ 48

Page 43

Course Outline for Electrical Training - SolidWorks Electrical: Schematic – 2 Days

1. Project Templates ▪ ▪ ▪ ▪ ▪ ▪ ▪

6. Wires and Equipotentials

SolidWorks Electrical Stages in the Process Starting SolidWorks Electrical What are Projects Project Templates Project Configurations How is a Project Structured

▪ ▪ ▪ ▪ ▪ ▪

Equipotentials and wires Wire style manager Replacing wire Equipotential numbering results Wire numbering results Using nodal indicators

7. Cabling 2. Modifying Project Templates ▪ ▪

▪ ▪ ▪ ▪ ▪ ▪

What are environments? Draw multiples wires

3. Drawing Types ▪ ▪ ▪ ▪ ▪ ▪ ▪

What are drawing types? Existing and Archived Projects Line Diagram Symbols Adding Cables Symbols Panel Schematic Symbols Symbol Properties

4. Symbols and Components ▪ ▪

What is a Component? Symbol component association

8. Symbol Creation ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Symbols and standards Symbols manager Symbol properties Circuits, terminals, types Multiple attribute Splitting attribute data Add to library Copy, paste symbol

9. Macros

5. Manufacturer’s parts ▪ ▪ ▪

What is cabling? Cables Detailed cabling Terminal strip Pin to pin connections Copy and paste

What are manufacturer’s parts? Circuits and terminals Finding manufacturer parts

▪ ▪

What are Macros Creating and Adding Macros

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 44

Course Outline for Electrical Training - SolidWorks Electrical: Schematic – 2 Days (CONTINUED)

10. Cross Referencing ▪ ▪ ▪ ▪ ▪ ▪

14. Connectors

What is cross Referencing? Cross Referencing List Cross Referencing State colors Cross Referencing Text coding Cross Referencing Types Cross Referencing Location List

11. Managing Origin-Destination Arrows ▪ ▪

What are Origin-Destination Arrows? Origin-Destination Arrows

12. Dynamic Programmable Logic Control ▪ ▪ ▪ ▪ ▪

What is a PLC? Adding a new scheme Adding a PLC Mark Inserting a PLC Editing a PLC

13. Automated Programmable Logic Control ▪ ▪ ▪

How are PLCs automated? PLC mark, part IO manager

▪ ▪

Connectors Insert connector

15. 2D Cabinet Layouts ▪ ▪ ▪ ▪ ▪

What are Cabinet layouts? Creating a 2D Layout Inserting Ducts and rails Inserting Components Wire cabling order

16. Design Rule Checks ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

What are design rule checks? Unconnected pins Equipotential conflicts Max. terminal wires Duplicated parent symbols Child symbols without parent Empty terminal strip Duplicated terminals

17. Reports ▪ ▪ ▪ ▪ ▪ ▪

What are Reports Report Manager Report columns Column formula SQL query column variable Sort and break

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 45

Course Outline for Electrical Training - SolidWorks Electrical: 3D – 1 Day

1. Adding a Cabinet ▪ ▪ ▪ ▪ ▪ ▪ ▪

4. Propagating 2D Changes to 3D ▪ ▪ ▪

Adding a Cabinet Un-archiving a Project SolidWorks Cabinet Layout Insert Component Inserting Rails Inserting Ducts Mates

5. Routing Wires

2. Inserting Components in the Cabinet ▪ ▪ ▪

Inserting Electrical Components Converting to an Electrical Component Inserting Terminals

3. Adding Door Components ▪ ▪ ▪

Adding Door Components Smart Components Inserting Smart Features

Propagating Schematic Changes to 3D Changes in SolidWorks Electrical Schematic Changes at the Assembly Level

▪ ▪ ▪

Routing Wires Routing Path Route Wires

6. Routing Cables ▪ ▪ ▪ ▪ ▪ ▪

Routing Cables Inserting Components Associate Component Adding Cable Glands Set Origin/Destination of Cables Route Cables

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 46

Course Outline for Electrical Training – SolidWorks Electrical Advanced – 1 Day

1. Library/Classification Management ▪ ▪

Creating a Library Library Filters

6. Connectors ▪ ▪ ▪

Connectors Insert Connector Connector Insertion

2. Importing DWG files ▪ ▪ ▪ ▪ ▪ ▪

Import DWG Files File Definition Symbol and Title Block Mapping Convert Attributes Configuration Files Review Results

3. Import Manufacturers Parts ▪

7. 3D Error Analysis ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Design Rule Checks Manufacturer Part Not Inserted Manufacturer Part Inserted Twice Missing Connection Point Incorrect CPoint Route Type Missing “,” Connection Point No Valid Path Wrong Wire Properties

Import Parts

8. Report Creation 4. ERP Database Connection ▪ ▪ ▪ ▪ ▪

ERP Database Connection ERP Connection Customize User Data ERP Data Flow Update Data

5. Export/Import From/To Excel ▪ ▪ ▪ ▪ ▪

Import/Export to Excel Excel Export/Import Configuration Export to Excel Import from Excel Replace Data

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Reports Lesson Structure Warning Basic Query Adding Fields Filtering Fields Writing a Complex Query Table Aliases User Data Counter Part Descriptions Can Sum Location Parts

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 47

Course Outline for Electrical

Training - SolidWorks Routing: Electrical – 1 Day 1. Fundamentals of Routing ▪ ▪ ▪

5. Standard Cables and Reusing Routes

What is Routing? Routing Setup General Routing Settings

2. Basic Electrical Routing ▪ ▪ ▪ ▪ ▪

Basic Electrical Routing Adding Routing Components Start by Drag and Drop Connector Auto Route Save to External Files

3. Routing with Clips ▪ ▪ ▪ ▪ ▪ ▪ ▪

Routing with Clips Routing Through Existing Clips Adding Clips while Auto Routing Editing a Route Working with Clips Splitting a Route Adding a Splice

4. Electrical Routing Components ▪ ▪ ▪ ▪ ▪ ▪ ▪

Routing Library Parts Introduction Electrical Routing Library Parts Libraries Routing Component Wizard Routing Component Attributes Electrical Libraries

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Using Standard Cables Standard Cable Excel File Modifying Standard Cables Creating a standard Cable Reuse route Delink harness Routing Templates

6. Electrical Data Import ▪ ▪ ▪ ▪ ▪ ▪

Importing Data Routing Library Manager From/To Lists Route Properties Route Guidelines Using Guidelines and Clips

7. Electrical Drawings ▪ ▪ ▪ ▪

Route Flattening and Detailing Annotation Flattening Flatten Route Manufacture Flattening

8. Electrical Conduits ▪ ▪ ▪ ▪ ▪ ▪

Electrical Conduits Rigid Conduit Orthogonal Routing with Auto Route Electrical Data in Conduits Manual Sketch Routing Flexible Electrical Conduit

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 48

SOLIDWORKS ADD-IN COURSE OUTLINE

Add-in training index Training - Introduction to Visual Basic.net – 2 Days ................................................................................................................................. 50 Training - SolidWorks API Fundamentals – 2 Days................................................................................................................................... 51 Training - SolidWorks Inspection – 1 Day.................................................................................................................................................. 52 Training - SolidWorks MBD – 1 Day ........................................................................................................................................................... 53 Training - SolidWorks Tolanalyst – 1 Day .................................................................................................................................................. 54 Training - DriveWorks Solo – 3 Days ......................................................................................................................................................... 55 Training - DriveWorks Adminisatrator – 4 Days ........................................................................................................................................ 56 Training - DraftSight – 1 Day ...................................................................................................................................................................... 57 Training - Power Surfacing – 1 Day ............................................................................................................................................................ 58 Training - MarkForged – 1 Day ................................................................................................................................................................... 59

Page 49

Course Outline for Add-Ins

Training - Introduction to Visual Basic.net – 2 Days 1. Introduction

12. Conventions

2. The basic interface

▪ ▪

3. Code



▪ ▪ ▪

Variable names Method names Argument names

13. Variables list

Types of variables Definition of variables The message box

▪ ▪

The array Collection

4. Compilation

14. The Timer control

5. VB Tools

15. Operators

▪ ▪ ▪

Benchmarks Breakpoints Keyboard Shortcuts

16. The text file ▪ ▪

Reading a text file Writing to a text file

6. Loops ▪ ▪ ▪

17. File Manager For ... Next Do ... Loop Force output

▪ ▪

18. Creating a method

7. If Statement 8. The Select Case statement 9. The interface of your programs ▪ ▪ ▪

Interface Language Activation checks Other interface parameters

10. Posts ▪ ▪

▪ ▪

Sub-type method The method of type Function

19. Manipulate the registry ▪

Management options in the registry of

20. Windows 21. Operations on the text

Simple message Message to capture the response

11. Goto

File Operations Operations on files

▪ ▪ ▪ ▪ ▪ ▪

Text comparison Conversion values Extracting a portion of text Extracting data from a file path Splitting text Replacement values

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 50

Course Outline for Add-Ins

Training - SolidWorks API Fundamentals – 2 Days *Training - Introduction to Visual Basic.net is a prerequisite for this class.

1. Using the Macro Recorder ▪ ▪ ▪ ▪ ▪ ▪ ▪

Macro Recording Macro Toolbar Understanding How Macro Code Works Understanding How to Call Members on API interfaces Passing Parameters Cleaning Up Code Adding Forms to a Macro

2. The API Object Model ▪ ▪

SolidWorks API Object Model Application Objects

3. Setting System Options and Document Properties ▪ ▪ ▪ ▪ ▪

User Preferences – System Option User Preferences – Document Properties Locating the Correct APIs and Enumeration Values User Preferences Tables For System Option, Document Properties and Menu Items

4. Automating Part Design ▪

Automation Tool for Parts

5. Assembly Automation ▪

7. Selection and Traversal Techniques ▪

The SolidWorks BREP Model

8. Adding Custom Properties and Attributes ▪ ▪ ▪ ▪ ▪ ▪

Custom Properties Configurations with Custom Properties File Summary Information Document Attributes The Attribute Objects Case Study: Face Attributes

9. The SolidWorks API SDK ▪ ▪

The API SDK Choosing a Programming Language

10. Customizing the SolidWorks User Interface ▪ ▪ ▪ ▪ ▪

Understanding The Add-in Code Property Pages Property Page Groups and Controls Removing Menus and Toolbars Other Areas of Customization

11. Notification ▪ ▪ ▪

Notification Notification in VBA Replacement values

Automation Tool for Assemblies

6. Drawing Automation ▪

Automating Drawing Creation

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 51

Course Outline for Add-Ins

Training – SolidWorks Inspection – 1 Day 1. Inspection Add-in ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Overview Inspection project Extraction settings Tolerance settings Project templates Characteristic tree Characteristic properties Balloon location Multiple characteristic instances Multi-line notes Exporting Design revision Manual Ballooning

2. Standalone Application ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Overview User interface Inspection project Extracting characteristics General characteristic tools Table manager Managing bill of characteristics Grids Multiple drawings Publishing reports Drawing revisions

3. SolidWorks Inspection Professional ▪ ▪ ▪ ▪ ▪

Overview Loading the inspection professional Add-in Measurements Input Publishing reports with inspection results CMM data import

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 52

Course Outline for Add-Ins

Training – SolidWorks MBD – 1 Day 1. Introduction to SOLIDWORKS MBD ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

What is SOLIDWORKS MBD? Course Layout MBD Using Feature Dimensions 3D PDF Capabilities MBD in SOLIDWORS MBD Using DimXpert DimXperts Capabilities STEP 242 Files MBD and Assemblies

2. Using Feature Dimension and Annotation Views ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Default Annotations Views Optimizing Settings Adding and Organizing Annotations Adding Reference Dimensions Modifiying Dimensions Creating a Section Annotation View Editing an Annotation View Unassigned Items Creating an Annotation View Note Area

▪ ▪ ▪ ▪ ▪ ▪

Areas of the Template Text Types Other Template Aspects Building a Custom Template Saving and Storing Custom Templates Testin Templates

5. Using DimXpert ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

DimXpert Settings DimXpert Block Settings DimXpert Dimension Settings How DimXpert works Auto Dimension Scheme DimXpertManager Show Tolerance Status Modifying DimXpert Annotations Combining Dimensions Publish Using Default Views Creating Multiple Schemes Manual DimXPert Annottions

6. MBD and Assembly Models

3. Capturing 3D Views ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

4. 3D PDF Template Editor

3D Views 3D Views Tab Capture 3D View Activating and Modifying 3D Views Using Multiple Annotation Views Publishing PMI Special 3D View Types Model Break View Publishing eDrawing File

▪ ▪ ▪ ▪ ▪ ▪ ▪

Assembly Models and MBD Assembly Level Dimensions Optimizing Settings in Assemblies Adding Assembly Annotations BOM Tables and Balloons Publishing Assembly PMI Additional MBD Tools

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 53

Course Outline for Add-Ins

Training - SolidWorks Tolanalyst – 1 Day The duration of training is about half a day but we will complete it with an example on one of your models or coaching on your examples. *There is no book for this class.

1. DimXpert ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

DimXpert Overview Auto Dimension Scheme Datums Size Dimensions Location Dimensions Geometric Tolerances Tolerance Status DimXpert Options Using DimXpert Information in Drawings Pattern Feature

2. TolAnalyst ▪ ▪ ▪ ▪ ▪ ▪

TolAnalyst Overview Establishing the Measurement Assembly Sequence Assembly Constraints Analysing the Results Fixed/Floating Fasteners

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 54

Course Outline for Add-Ins

Training - DriveWorks Solo – 3 Days

Lesson 1 ▪ ▪

Lesson 7 ▪

Basic Setup Capturing your Models

Form Navigation

Lesson 8 Lesson 2 ▪

▪ ▪

Project Designer

Lesson 3 ▪

Lesson 9 ▪

Building Rules

Lesson 4 ▪

Driving Custom Properties

Lesson 10 ▪

Improving your Project

Lesson 5 ▪

Enhancing your Forms Dynamic Replacement Files

Documents

Lesson 11

Static Replacement Files



Drawings

Lesson 6 ▪

Tables

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 55

Course Outline for Add-Ins Training - DriveWorks Adminisatrator – 4 Days Lesson 1 ▪

Lesson 11

Creating a Group and Capturing Models

Lesson 2 ▪

Building a user interface in DriveWorks Administrator



Building Rules



Running your Project

File Name and Relative Path Rules

Specification control



Linking to data

Lesson 16 (Advanced) ▪

Tables

Lesson 7 ▪ ▪ ▪ ▪

Advanced form controls

Lesson 15 (Advanced)

Lesson 6 ▪

Specification flow Preparing your models for automation

Lesson 14 (Advanced)

Lesson 5 ▪

▪ ▪

Lesson 13 (Advanced)

Lesson 4 ▪

Drawings

Lesson 12

Lesson 3 ▪



Rollup data tables

Lesson 17 (Advanced)

Form navigation Form templates Static and dynamic control properties Advanced form controls



Hierarchical properties

Lesson 18 (Advanced) ▪

Macro buttons

Lesson 8 ▪

Dynamic replacement files

Lesson 19 (Advanced) ▪

Generation tasks

Lesson 9 ▪

Data management

Lesson 10 ▪

Documents

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 56

Course Outline for Add-Ins Training - DraftSight – 1 Day 1. User Interface ▪ ▪ ▪ ▪ ▪ ▪

6. Drawing Files

Pointing Device -DraftSight Window Title Bar - Pull-Down Menu Toolbars - Graphic Windows Commande Line - Status Bar Shortcut Menus - Dialog Boxes Keyboard Options - Help Menu

2. Creating a Simple Drawing ▪ ▪ ▪ ▪ ▪

New - Line Delete Command - Rectangle Circle -Drafting Settings Arc - Undo and Redo Polygon- Drawing Setup

3. Coordinates ▪ ▪ ▪ ▪

Coordinated System- CCS Icon Inquiry - Units Coordinate Entry - Snap from Entity Snap Drawing Boundary

▪ ▪ ▪ ▪

7. Advanced Commands ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

Point - Point Format Mark Divisions - PolyLine Explode- Edit PolyLine Blocks -Insert Block Clean -ExportDrawing Hatch - Pattern Stretch - Change Length Split - Fillet- Chamfer EntityGrips- Egrip Settings

▪ ▪ ▪ ▪

Dynamic Pan - Dynamic Zoom Zoom Window - Zoom Previous Zoom Options - Rebuild Named Views - Multiple ViewTiles

9. Text and Dimensions

Selecting Entities Move Command - Copy Command Offset Command - Mirror Command Rotate Command - Scale Command Trim Command - Extend Command

5. Properties and Layers Toolbars ▪ ▪

New – Save - Open File Management - File Utilities

8. View Commands

4. Modify Commandes ▪ ▪ ▪ ▪ ▪

▪ ▪

Layer Control - Activate Layer Command Color Control Command - LineStyle Control Command LineWeight Control Command Layers Manager Command Property Painter Properties Command

▪ ▪ ▪ ▪ ▪ ▪

Simple Note – Note Text Style – Edit Annotation Find and Replace – Spell Check Dimensions – Dimensions Style Edit Dimension Location - Edit Dimension Text Edit Dimension Properties

10. Drawing Output and Layout ▪ ▪

Drawing Layout – View Tiles Working with Viewports on Sheets- Print

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 57

Course Outline for Add-Ins Training – Power Surfacing – 1 Day 1. Basic Operations ▪ ▪ ▪

Basic Manipulations Extrude Insert loops

2. Operations (Continued) ▪ ▪

Hard Line Define Boundary

3. SolidWorks Body References ▪ ▪ ▪

Import References Constrain to… Auto Update All Constrains

4. Spatial Constrains ▪ ▪

Retain Offset Constrain Retain Ratio Constrain

5. Advance Operations ▪ ▪ ▪

Advance Manipulations Thicken Symmetry

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 58

Course Outline for Add-Ins Training – MarkForged– 1 Day 1. Preparation ▪ ▪ ▪ ▪

5. Advance Operations

Unboxing Verifying Boxes Content Printer Installation Plugging the Printer on the Network

2. Introduction ▪ ▪ ▪ ▪ ▪ ▪

SolidXperts Introduction Good Use of 3D Printing Comparison Against ABS Useful Web Pages Eiger Account Creation Introduction to STL files

▪ ▪ ▪ ▪

3. Maintenance and Calibration ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪

3D Printer Components The Use of USB Key Leveling Technic Fiber Nozzle Adjustment Test Prints Nozzle Cleaning Plastic and Fiber Nozzle Replacement Wet Plastic Purge XY Adjustment Strap Tensioning

Menu Options Fiber / Sandwich Technic Type of Fiber Filling Part View and Internal View Visibility Options Completely Filling a Part of Fiber Completely Filling a Part of Plastic Helping the Fiber Pathing by Changing the Geometry Helping the Fiber Pathing by Changing the orientation of the Part Brim Opening a Request to MarkForged Saving the Logs

6. Question ▪ ▪

Questions Starting a Print with a Custom Part

4. Information ▪ ▪ ▪

Part Glue Print Information Mechanical Properties

Course Objectives: At the end of the course, the student will know the capabilities of the software and will be able to use the features. Training Course: Training is held in a laboratory class and each student has their own station. Methodology: Training is based on case studies demonstrated by the instructor. At the end of each lesson, time will be given for exercises. Competences Evaluation: During the class work, the instructor will show the exercises and explain the solutions to the entire class. Instructor: SolidXperts trainers are Certified SolidWorks Instructors (CSWI) and authorized by Emplois Québec. Course Materials: One or more training manuals are included with the training course (Exceptions apply to teachers and students from educational institutions). Attestation: A certificate will be given to the student at the end of the course to attest the successful completion of the requirements for the course.

® SolidXperts, inc. All Rights Reserved.

Page 59

SolidWorks Training Courses Focus on Fundamental Skills and Concepts that are Key to Ensuring your Success with SolidWorks. SolidXperts provides both basic and advanced training of the highest quality. Our trainers are certified by DS SolidWorks Corp. Select your training requirements by viewing the courses available for SolidWorks products, including SolidWorks, SolidWorks Simulation, SolidWorks PDM, and SolidWorks Composer. Each course includes a training book, as well as practice sessions for which each participant is given access to a computer. We recommend this course to people who have previous experience with SolidWorks.

SolidXperts (Nashua, NH)

SolidXperts (Montréal)

SolidXperts (Québec)

98 Spit Brook Road, Suite #304 Nashua, NH 03062

2650 Marie Curie Ave. Saint-Laurent, QC, H4S 3C3

1173 Charest blvd. West, Suite #350 Québec, QC, G1N 2C9

Telephone: 877.876.5439 Fax: 877.876.5431 Email: [email protected]

Telephone: 877.876.5439 Fax: 877.876.5431 Email: [email protected]

Telephone: 877.876.5439 Fax: 877.876.5431 Email: [email protected]

Tech Support: 877.824.3379 Tech Email: [email protected]

Tech Support: 877.824.3379 Tech Email: [email protected]

Tech Support: 877.824.3379 Tech Email: [email protected]