specification guide - Open Plan Systems

SPECIFICATION GUIDE

A QUICK DESIGN & SPECIFICATION REFERENCE TOOL

TABLE OF CONTENTS

To navigate through the manual quickly, click on the teal title to get you where you’d like to be!

PANEL SYSTEMS......................... 3

ELECTRICAL............................ 10

Monolithic Options............................ 3 Segmented Options.......................... 3 Fabric & Glass Stackers..................... 3 Marker Board Stacker........................ 3

V1 and V2 Power Differences.......... 10 Installation Instructions..................... 10 Festoon 19 ..................................... 10 Festoon 23 ..................................... 10 Power in Straight Run....................... 10 Power With 90° Connection............. 10

MODULAR WALLS..................... 3 Modular Wall Options........................ 3

TILE SYSTEM ............................. 4 Tile Finish Options.............................. 4 Base Options..................................... 4

DESKING SYSTEM ..................... 5 Low Storage...................................... 5 Pedestal............................................ 5 Storage Towers.................................. 5 Overhead Storage............................ 5

LEG OPTIONS........................... 5 Square Leg........................................ 5 Post Leg............................................. 5 Column Leg...................................... 5 P-Leg................................................. 5 Docking Leg...................................... 5 T-Leg ................................................. 5 Center Leg........................................ 5 C-Leg................................................ 5 Corner Leg........................................ 5 Arc T-Leg........................................... 5 Square H-Leg.................................... 5 H-Leg ............................................... 5

MULLION OPTIONS................... 6 PGHM Mullions................................... 6 DSH Mullions (Desk Screen Dividers)... 6

ELEVATION SERIES................... 11 VALUE SERIES.......................... 12 CASEGOODS......................... 12 STORAGE............................... 13 Pedestals ........................................ 13 Overheads ..................................... 13 Lateral Files ..................................... 13 Towers............................................. 13

ACCESSORIES........................ 14 Paper Management....................... 14 LED Task Light.................................. 14 Data/Power Unit............................... 14 Keyboard Sets ................................ 14

CONNECTORS....................... 15 2-Way Connectors........................... 15 3-Way Connectors........................... 15 4-Way Connectors........................... 15

PROGRAMS............................ 16 Systems Furniture ............................ 16 All New Signature Series .................. 16 Sustainable Series ........................... 16

PANEL DETAILS.......................... 7 Version 1 and Version 2 Power........... 7 Top Cap............................................ 7 Panel Core, Frame and Faces.......... 7 Hanger Rails...................................... 7 Base.................................................. 7 Panel Options.................................... 7

WORK SURFACE OPTIONS......... 8 Table Tops......................................... 8 Specialty Work Surfaces.................... 9 Counter Caps................................... 9 Wood Grain....................................... 9

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

2

SYSTEMS PANEL SYSTEMS: MONOLITHIC OPTIONS

*Laminate Panels offered in BU, Empire Mahogany, White Frost and Shadow Ridge only for an up-charge

PANEL SYSTEMS

WIDTHS

Heights

*LAMINATE PANELS

FABRIC

FABRIC TACKABLE

12, 18, 24, 30, 36, 42, 48, 60

24, 30, 36, 42, 48, 60

12, 18, 24, 30, 36, 42, 48, 60

12, 18, 24, 30, 36, 42, 48

24, 30, 36, 42, 48

32, 39, 47, 53, 62, 67, 85, 95, 107

53, 62, 67, 85

53, 62, 67, 85, 95, 107

32, 39, 47, 53, 62, 67, 85, 95, 107

67, 85

ACOUSTICAL

PARTIAL GLAZED STACKERS

OPEN

24, 30, 36, 42, 48

24, 30, 36, 42, 48, 60

24, 30, 36, 42, 48

67, 85

53, 67, 85

67, 85

PARTIAL GLAZED

GLAZED

PANEL SYSTEMS: SEGMENTED OPTIONS STACKER

QTY

PANEL

TOTAL

14”

1

fabric, glazed, or marker board

STACKER TYPE

39”

53”

20”

1

fabric or glass

47”

67”

14”

1

fabric, glazed,or marker board

53”

67”

18”

1

fabric, glazed, or marker board

67”

85”

(a) 14”

1

53”

85”

(b) 18”

1

(a) fabric, glazed, or marker board (b) fabric, glazed, or marker board

(a) 14”

2

39”

85”

(b) 18”

1

(a) fabric, glazed, or marker board (b) fabric, glazed, or marker board

Glass Stacker

Fabric Stacker

Panel

FABRIC & GLASS STACKERS

MARKER BOARD STACKER

Note: Segmented with Panel + Glass Stackers only are specified as Partial Glazed Stackers

Note: The standard marker board stacker has marker board material on one side. Marker board material can be requested on both sides for an up-charge.

MODULAR WALL OPTIONS

• • • • •

MODULAR WALLS

Any panels over 85”H are considered Modular Walls Available in Fabric, Acoustic, & Laminate Panels 85H available in monolithic or segmented options Optional ceiling channel trim adds finishing touch to floor-to-ceiling modular walls Note: Modular Walls fall under the Signature Program but utilize V1 rails



Fabric Only



Fabric or Glass

14”

18”

22”

85”

85”

107”

10” 85”

SEGMENTED 95”

95”

MONOLITHIC 95”

85”

SEGMENTED 99”

SEGMENTED 103”

SEGMENTED 107”

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

MONOLITHIC 107”

3

*TILES WIDTHS Frame Heights

TILE SYSTEM

24, 30, 36, 42, 48 39, 53, 67

*Laminate Tiles offered in BU, Empire Mahogany, White Frost and Shadow Ridge only

Panel Widths: 24, 30, 36, 42, 28

TILE FINISH OPTIONS PERFORATED PAINTED METAL (PPMT) Our 18” bottom tile comes standard with perforated paint unless otherwise specified. Perforated painted tiles are available on 18” bottom tile only. FABRIC TACKABLE ACOUSTIC (FTA) Our standard fabric tiles are tackable acoustic. Choose from any of our standard fabric selections. LAMINATE (LAM) Four standard laminate options are available. OPEN/GLAZE TILES All tiles are specified for each side of the frame. When using a glass tile, it is recommended to use open on the inside and glass on the outside. GLASS (G/OT OR G/OM) Our glass tiles come standard with glass on one side and an open frame on the other. Glass on a top tile is denoted G/OT and glass on a middle tile is denoted G/OM. Glass cannot be used on 7” tiles or 8” stacker tiles. PAINTED METAL TILE (PMT) All standard paint options are available. OPEN TILE (O/O) Open tiles consist of open frames on both sides of the tile frame, thus allowing for open access.

BASE OPTIONS B2 BASE

B1 BASE

RAZOR THIN BASE

Programs: STANDARD with All New Signature, Sustainable C2, and 2 Week Quick Ship orders

Programs: STANDARD with 5 Day Lightning

Programs: Optional with all new Signature Program Only

OPTIONAL with other orders (All New Signature, Sustainable C2, 2 Week Quick Ship Programs) Note: B1 Base not offered in WF finish

Recommended for: Those wanting cleaner lines, Lighter Base color options No Rubber Gaskets (OPS Standard)

Recommended for: Heavy Traffic, Telemarketing Stations, Matching up to Existing Stations, Panel Generated Hallways

Recommended for: Modern Look, Chic Design, Streamline Rubber Gaskets (Optional with other programs)

Note: V1 Power and Thin Receptacles required

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

Razor Thin Base (Optional) Note: Base covers are shipped seperately from the panels on Razor Thin Base Orders

4

DESKING SYSTEM LOW STORAGE Widths: 24, 30, 36

TWO DRAWER

OPEN SHELF

SLIDING DOOR

CUSHION AND LAMINATE TOP (OPTIONAL)

PEDESTAL

BOX/FILE STORAGE TOWERS

37”H

51”H

STORAGE CABINET W/ SLIDING DOOR *Recommended for 67”h Panels

UPMOUNT STORAGE CABINET W/SLIDING DOOR *Recommended for 53”h Panels

OVERHEAD STORAGE *Door can be painted or fabric

LEG OPTIONS

SQUARE LEG

POST LEG

COLUMN LEG

P-LEG

CENTER LEG *Shown with Modesty Panel

C-LEG

CORNER LEG *Shown with Modesty Panel

ARC T-LEG

• DOCKING LEG

SQUARE H-LEG

T-LEG

H-LEG

• Use an Extended Docking Leg when laminate top is not specified. www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

5

MULLION OPTIONS PGHM MULLIONS

Note: *24, 30, 36, 42 and 48 mullions come with two PGHM’s | *60 and 72 mullions come with four PGHM’s Our new PGHM Universal Mullions can be added to work surfaces, table tops, OPS2 Panels and OPS2 tiles to provide a unique look or a sense of privacy! Our standard mullions are offered in clear tempered glass, clear plexiglass or fabric. Frosted, bronzed and smoked mullions are also available at an up-charge. Custom mullion heights are available for fabric or plexiglass mullions in clear, bronzed, frosted or smoked plexiglass at an up-charge. Custom heights are not available for tempered glass mullions.

PAINTED PGHM

FROSTED PLEXIGLASS MULLION USED AS A MODESTY PANEL

FROSTED MULLION ON A PANEL

FABRIC MULLION ON A WORK SURFACE

DSH MULLIONS (DESK SCREEN DIVIDERS)

Our new PGHM Universal Mullions can be added to work surfaces, table tops, OPS2 Panels and OPS2 tiles to provide a unique look or a sense of privacy! Our Desk Screen Dividers compliment the mullion screens and modesty panels at the same time! Choose from our 5 standard paint finishes (not available in nickel finish.)

DESK SCREEN DIVIDER- FRONT

DESK SCREEN HOLDER

DESK SCREEN DIVIDER- BACK

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

6

Top Cop

PANEL DETAILS

Wedge Block

DESCRIPTION The structural panel is fabric covered with a painted top cap, 14 gauge steel hanger frames, cable management side cover and adjustable glides. It is UL listed and has a Class A fire rating for both flame spread and smoke development. The powered panel has a factory installed electrical harness that distributes double-sided, 4 circuit power within a cable management raceway. Electrical components are UL listed.

Wood Screws

Panel Blank

Side Rail *Version 2 Power Shown

Base Kit

Version 1 Power

Top Cap

The 4-circuit power outlets are located 10” from the end of the base on each panel, allowing for two duplex receptacles on each side of 30”-60” panels and one on each side of a 24” panel. Separate jumpers are used to connect power from one panel to another. Version 1 Power is utilized with all Sustainable options and Thin Base.

The top cap is either mold plastic or 25 gauge cold rolled steel.

*Version 2 Power The 4-circuit power outlets are located in the middle of the base on each panel, allowing for two duplex receptacles on each side of a 24”60”W panel. Attached to the power harness are the jumpers for power continuation from panel to panel and panel through connector. Version 2 power is utilized in our Signature program.

Panel Core, Frame and Faces The panel core is constructed from corrugated, honeycombed paperboard. The frame consists of a top rail and bottom rail and stiles (uprights) of 2” timberstrand. The panel faces are glued to the front and back of the core and the frame and shall be a 1/8” medium density fiberboard.

Hanger Rails The 2 hanger rails, which for the vertical frame between panels are made from painted, 14gauge, cold rolled steel. They include slots at 1” increments for hanging components. Phillips head screws attach the hanger rails to the stiles.

Base The 4 5/8” high, 3 ¼” deep base is a galvanized, 24 gauge cold rolled steel base plate, 2 stell support posts and 2 cable management side covers of extruded, fire retardant PVC plastic. The support posts have grooved edges with the groove on the bottom hinging the side cover to the base and the groove on the top hooking the side cover under a plastic lip on the bottom of the panel. Side covers with receptacle locations have snap-in fillers.

PANEL OPTIONS

A - Fabric Panel B - Fabric Tackable Panel C - Acoustic Panel D - Partial Glazed Panel (plexiglass) E - Partial Glazed Stacker Panel (tempered glass) F - Glazed Panel (plexiglass) G - Open Panel

A, B or C

D

E

F

G

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

7

WORK SURFACE OPTIONS Type: Curvilinear Corner Widths: 36”-48” Depths: 24”, 30”

Type: Corner Wedge Dim: 11” x 16” x 11”

Type: Extended Corner (L or R) Widths: 42”-72” Depths: 24”, 30”

Type: Ext. Curv. Corner (L or R) Widths: 42”-72” Depths: 24”, 30”

Type: Cockpit Widths: 36”-96” Depths: 24” & 30”

Type: Depth Transition Corner Widths: 36”-48” Depths: 24” & 30”

Type: Depth Transition Curved Corner Widths: 36”-48” Depths: 24” & 30”

Type: C-Shaped (L or R) Widths: 42”-48” Depth: 24”

Type: Peninsula Widths: 48”-84” Depths: 24”, 30”, 36”

Type: Conference Peninsula Widths: 60”-84” Depth: 30”

Type: Ext Corner Peninsula Widths: 48”-84” Depths: 24”, 30”

Type: Ext Curved Corner Peninsula Widths: 48”-84” Depths: 24”, 30”

Type: 120 Degree Widths: 24”-60” Depths: 24”

Type: 120 Deg Corner Corner Widths: 24”-60” Depth: 24”

Type: 120 Deg Ext Corner Corner Widths: 36”-60” Depth: 24”

Type: Round Widths: 30”-60”

Type: Rect. Conference Widths: 60”-96” Depths: 36”-48”

Type: Training Table Widths: 60”-96” Depths: 18”-30”

12 0

90

Type: Square Dimensions: 30”-60” Square

°

*TABLE TOPS

Type: Corner Widths: 36”-48” Depths: 24”, 30”

°

Type: Rectangular Widths: 18”-96” Depths: 24”, 30”, 36”

Type: Racetrack Conference Widths: 60”-96” Depths: 36”-48

*Table legs must be specified separately from tops

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

8

WORK SURFACE OPTIONS CONT. Type: Quarter Round Inside Widths: 24”-30”

Type: Quarter Round Outside Widths: 24”-30”

Type: Single Round Widths: 31”-79”

Type: Counter Center, End and Mid End Brackets

SPECIALTY WORK SURFACES

Type: D-Tops Widths: 52”-63-3/8” Depths: 26”-31-3/4”

COUNTER CAPS

Type: Rectangular Widths: 24”-72”

Type: Double Round Widths: 64”-88”

Type: Round Corner Widths: 32-7/8”-44-7/8” Depths: 32-7/8”-44-7/8” Center Bracket (CB)- Needed when two counter caps meet Mid End Bracket (MEB)- Needed when a counter cap is located at the end of a panel run where there is a connector instead of an end cap

Type: Square Corner Widths: 32-7/8”-44” Depths: 32-7/8”-44”

Type: 120 Degree Widths: 32-7/8”-44-7/8” Depths: 32-7/8”-44-7/8”

Notes: *V1 rails must be used when you have an in-line panel to panel drop down *Metal end caps must be used when an End Bracket is applied (Plastic will not work) *MEB is required at a wall start location

Type: Cross-Grain D-Top 1% of list up-charge

Type: Standard Pen. Top

Type: Cross-Grain Pen. Top 1% of list up-charge

Type: Diagonal Corner 1% of list up-charge

Type: Standard Ext. Corner

Type: Cross Grain Ext. Corner 1% of list up-charge

WOOD GRAINS

Type: Standard D-Top

Type: Standard Corner

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

9

ELECTRICAL WHAT IS THE DIFFERENCE BETWEEN V1 AND V2 POWER?

While there is no difference in the Power Entry Kit and the 4 circuit wiring in the PEK or ceiling feed, the power harness and connections in the panel base are completely different. On V1 power, the power harness runs almost the length of the base, with the receptacle locations at each end. To connect from one powered panel to an adjacent powered panel, a festoon is required. The festoons are completely separate from the harness and must be snapped into the ends of each power harness in the two panels. Our festoons come in two lengths,19” and 23”. The 19” festoons connect straight running panels and panels at 90 degree angles. On power passing through 3 and 4 way connections, the 23” festoon is required. NOTE: V1 rails the wedge block and slotted channel are always BU. On V2 power, the power harness is shorter and the receptacle locations are in the center of the panel. The flexible harness that connects the adjacent panels together is connected to the power harness. There are not any festoons required to connect the power from panel to panel.

WHAT AMP IS OUR RECEPTACLE?

In keeping with the standards of the major OEM’s, Open Plan Systems’ receptacles are rated at 15 amps and the 8 Wire Harness is rated at 20 amps.

POWER IN STRAIGHT RUN

POWER WITH 90° CONNECTION

3-WAY

2-WAY

Festoon23

39/12P

Festoon19

39/12P 39/12P

Orders with Version 1 power require festoons (what many installers call jumpers) to connect power from one panel to another. OPS provides 2 different length festoons. One is 19½” long which OPS identifies as a festoon19 and the other being a 23” long festoon which OPS identifies as a festoon23. These will be individually labeled by name and by length.

39/24C

INSTALLATION INSTRUCTIONS

39/12P

FESTOON19

3-WAY

39/24C

4-WAY

39/12P

39/12P 39/12P

Used at all straight panel to panel connections or all powered panels meeting at a 90° connection. This includes all 2-way, 3-way, and 4-way 90° connections.

39/12P

FESTOON23

NOTE: Only 3 festoon19s are required in 4-way 90° applications. Only 2 festoon19s are required in 3-way 90° applications. Using additional festoon19s could cause a short in the electrical system.

39/12P

4-WAY

KEY Festoon19: 19½” Festoon23: 23”

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

39/12P

39/12P

39/12P

Orders are shipped with the required amount of festoon23s. If you are short on festoon23s, make sure they were not used as a 90° connection.

39/12E

39/24C

Used at all 3-way and 4-way connections which have power going straight through the connector to another powered panel. Festoon23 is only used on a straight run.

10

ELEVATION SERIES

13 Swivel Chairs, 3 Guest Chairs, 1 Stool Kit

MESH SEAT OPS-B1

FABRIC SEAT

l

OPS-B1FS

l

OPS-B3

l

MESH BACK

FAUX LEATHER

RATCHET BACK

BACK REST TILT

SEAT HEIGHT /TENSION ADJUSTMENT

ARM PADS IN/ OUT

ARM PADS UP/ DOWN

HEIGHT (Inches)

DEPTH (Inches)

WIDTH (Inches)

WEIGHT (Lbs.)

OPS-B1

39-43

25.5-27

28

46

OPS-B1FS

40-41.5

25.5-27

28

46

l

l

l

l

l

l

l

l

l

l

l

l

OPS-B3

45-56

25.5-27

26

49

OPS-B4

40-45

25.5-27

26

49

Faux Leather Seat Plastic Back

l

l

l

l

l

l

l

l

l

l

l

l

OPS-B6

l

l

l

l

l

l

l

l

OPS-B6-300

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

MODEL

l

l

OPS-B8

FIXED LUMBAR

l

l

OPS-B4

SEAT SLIDER

l

OPS-822A

l

l

l

OPS-822B

l

l

l

OPS-9838A*

l

l

l

l

l

OPS-9838B*

l

l

l

l

l

OPS-9838D

l

OPS-C2

l

l

OPS-C8

l

l

OPS-B1

OPS-B1FS

OPS-B3

OPS-B8

OPS-822A

OPS-822B

OPS-B6

39-44

25.5-27

26.5

44

OPS-B6-300

39-44

25.5-27

29.5

50

OPS-B8

40-43

26-27.5

24

43

OPS-822A

46-48

27

25

52.5

OPS-822B

39-41

28

25

49

OPS-9838A

47-49

25

25.5

56

OPS-9838A.L

47-49

25

25.5

56

OPS-9838B

41-43.5

25

25.5

56

OPS-9838B.L

41-43.5

25

25.5

56

OPS-9838D

40

29

22.5

54

OPS-C2

40

25-26

23.5

42

OPS-C8

41.5

25-26

24

40

OPS-B-CHKIT

22-29

-

-

-

OPS-B4

OPS-B6

OPS-B6-300

OPS-9838A*

OPS-9838B*

OPS-9838D

*Available in leather and vinyl ‡ Available for B1, B4 and B6 chairs only. Comes with: Glides or cast and round ring. Adds 22”-29” to chair height. We will be disconnecting the tilt adjustment lock for safety reasons

OPS-C2

OPS-C8

OPS-B-CHKIT‡

*

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

11

VALUE SERIES

5 Swivel Chairs, 2 Guest Chairs

METAL BASE OPS-900

PLASTIC BASE

l

OPS-5688

l

MESH BACK

l

l

l

l

l

l

l

l

l

l l

OPS-4032

l

OPS-900

FABRIC SEAT

l

OPS-4019

OPS-3119

SQUARE ARMS

l

OPS-4008

OPS-3159

ROUND ARMS

l l

l l

HEIGHT (INCH)

DEPTH (INCH)

WIDTH (INCH)

WEIGHT (LBS)

37-40

25

24

41

40-47

25

27

45.5

48-53

27

26

44

l

41-44

27

26.5

34

l

l

41-45

22.5

25

26.5

l

l

l

31

23

21.5

16.5

l

34

27

24.5

19

l

OPS-4008

CASEGOODS, LAMINATE SERIES

OPS-5688

SEAT SLIDER

RATCHET BACK

GUEST CHAIR

l

l

OPS-4019

Features • Reeded Profile with 1-1/8” Edge • Silver or Black hardware • Freestanding shells and reversible returns • Recessed modesty panels • Hutch tops with wood doors or frosted glass doors • Bow-front or standard desktops • Hanging or full pedestals, fully-locking • Wire-management grommets • File drawers with adjustable metal bars for hanging folder • Adjustable levelers for uneven floor surfaces

OPS-4032

OPS-3159

WARM CHERRY

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

OPS-3119

ESPRESSO

12

STORAGE SQUARE PULL*

FULL PULL*

A-STYLE

B-STYLE *Square Pull Pedestals available in BU, HF, LT and MT Finishes *Full Pull Pedestals available in BU, HF, MT and WF Finishes

PEDESTALS

OVERHEADS SQUARE PULL

FULL PULL

A-STYLE

B-STYLE

B-STYLE PAINTED

BBF

TYPE

X

X

Flipper Door

X

X

X

FF

X

X

Open Shelf

X

X

Mobile BBF

X

X

Half Height Shelf

X

X

Mobile FF

X

X

Storage Cabinet w/ Sliding Door (Painted or Fabric Door Options)

X

Upmount Storage Cabinet w/Sliding Door (Painted or Fabric Door Options)

X

21”D BBF

X

21”D FF

X

Budget Mobile

X

Hanging BF

X

Box/File (Desking)

X

TYPE

*Seat cushions available for square pull and full pull pedestals. Budget mobile cushion is the only one that will fit under a work surface.

BBF FULL PULL

FF SQUARE PULL

2 Drawer

SQUARE PULL

FULL PULL

X (30”w only)

X

3 Drawer

X

4 Drawer

X

5 Drawer

X

2 DRAWER

OPEN SHELF

STORAGE CABINET W/ SLIDING DOOR

UPMOUNT CABINET W/ SLIDING DOOR

HALF HEIGHT SHELF

BUDGET MOBILE W/ SEAT CUSHION

LATERAL FILES Widths: 36, 42, 48 TYPE

FLIPPER DOOR

TOWERS FULL PULL

COMES W/ LAMINATE TOP

PART OF DESKING SYSTEM

37”h

X

X

X

51”h

X

X

X

63”h

X

X

TYPE

HANDED (L OR R)

X

4 DRAWER

*Full Pull lateral files available in BU, HF, MT and WF finishes *Square Pull 30”W 2 Drawer Lateral File available in BU, HF, LT and MT finishes

37”H

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

51”H

63”H 13

ACCESSORIES Additional Accessories Available TYPE

ADDITIONAL NOTES

Paper Management

Diagonal & vertical paper trays, binder holders

16”H Tackboards

A-Style, B-Style or Powered

12”H Tackboards

A-Style or B-Style

LED Task Light

Connection Cords available

TLN Task Light

UL Listed

Cord Manager

Hides Task Light Cords

Marker Boards

Standard with Trays

Coat Hooks

Plastic or Metal

Data/Power Unit

UL approved and can be surface mounted

Monitor Arms

Single or Dual, Clamp or Grommet Mount

Pencil Drawer

Black Only

Computer Case Holder

Strap supported CPU under desk top

Metal CPU Holder

Metal supported CPU under desk top

PAPER MANAGEMENT

LED TASK LIGHT

DATA/POWER UNIT

KEYBOARD SETS- 6 OPTIONS ARM TRACK

HEIGHT ADJUSTMENT

10.5"

17"

Varies*

No

Varies*

11"

21"

5.25"

Yes

+/- 15°

20"

11"

21"

8.25"

Yes

+/- 15°

27"

11.5"

21"

12.5"

No

+/- 15°

AKAMINICOBRASLIMFORM

20"

10.5"

21"

8"

Yes

+10° / -20°

AKACOBRASLIMFORM

20"

10.5"

23"

12.5"

Yes

+10° / -20°

SET NAME

SET SKU

AKA/Refurb Set Value Set Value Set Extended Better Set Best Set Best Set Extended

TRAY WIDTH

TRAY DEPTH

AKAREFURB

23"

AKAVALUE

20"

AKAVALUEEXT AKANEW2

AKA/REFURB SET

VALUE SET

BEST SET

BEST SET EXTENDED

VALUE SET EXTENDED

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

MOUSE TRAY

TILT

BETTER SET

14

CONNECTORS Type: 2 Way 90

Type: 3 Way 90

Type: 4 Way 90

Type: Panel to Panel (Draw Rod)

Type: Wall Start (TC)

Type: Wall Track

Description: These connectors join two panels of equal or unequal heights at a 90 degree angle. If connecting panels of unequal heights, connector height should equal height of higher panel.

Description: This draw rod connects panels of equal or unequal heights in a straight line. Unequal heights in a straight line also require a Change of Height connector. (COH)

Description: These connectors join three panels of equal or unequal heights at a 90 degree angle. If connecting panels of unequal heights, connector height should equal height of higher panel.

Description: Wall starts are used to connect a panel to an architectural wall or column. They do not include the 5” base height.

Description: These connectors join four panels of equal or unequal heights at 90 degree angles. If connecting panels of unequal heights, connector height should equal height of higher panel.

Description: These wall strips attach to a structural wall for the purpose of hanging components.

Wall Track

Type: Variable Height Filler (VHF)

Description: When two panels of unequal heights are joining at a connector, a VHF is used to cover the exposed end of the panel.

Type: Change of Height (COH)

Description: When two panels of unequal heights are joining in a straight line, a COH is used to cover the exposed end of the panel. COH height is equal to the height of the lower panel.

2-WAY CONNECTORS

Left

COH (Change of Height) When two panels of unequal heights are joining in a straight line, a COH is used to cover the exposed end of the panel.

Right

3-WAY CONNECTORS

VHF (Variable Height Filler) When two panels of unequal heights are joining at a connector, a VHF is used to cover the exposed end of the panel.

Left

Right

Bottom

4-WAY CONNECTORS Top

Left

Right Bottom

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

15

PROGRAMS Programs are defined by the fabric and finish trim selected for panels.

SYSTEMS FURNITURE PROGRAM

FABRIC OPTIONS

WORK SURFACE OPTIONS

BASE COLOR OPTIONS

TRIM OPTIONS

RAILS

ELECTRIC

TOP CAP

SHIPPING TIME

‡ All New Signature

250+

16

4

6

V2

V2

Aluminum

3 weeks

Sustainable C2

31

4

2

3

V1

V1

Plastic

3 weeks

º 2 Week Quick Ship

6

4

2

2

V1

V1

Plastic

2 Weeks

º 1 Week Lightning

4

3

2

2

V1

V1

Plastic

1 week

250+

16

4

6

V1/V2

V1/V2

Plastic/Alum

10 Weeks

*10 Week

‡ Our Modular Walls fall under the Signature Program but utilize V1 Rails and V2 Power ‡ Our Thin Base option fall under the Signature Program but utilize V1 Power ºLimited Selection; Please see Lightning Brochure and Quick Ship flyer for more information * 10 Week Program has full access to all Signature and Sustainable programs- reduced pricing because of longer lead times

ALL NEW SIGNATURE SERIES

*Encompasses the largest selection of fabrics, paints and laminates using all new product.  *Included under the OPS2 Signature Series are the following lines: Panels, Tiles, Modular Walls, and Desking ÌÌ Save up to 35% off the cost of comparable

SUSTAINABLE SERIES

The OPS2 Sustainable Series, shows our proud roots in remanufacturing. *Panel core, connector core and overhead core are remanufactured. Everything else is new! *Included in the Sustainable Series are our C2, Lightning, and Quick Ship Programs. ÌÌ Save up to 40% off the cost of comparable

www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.06.15

16