Switching Basics and Intermediate Routing CCNA 3 Labs and Study ...

Switching Basics and Intermediate Routing CCNA 3 Labs and Study Guide ISBN: 1-58713-171-4 Errata 1st Printing CHAPTER 1 Page 31

Missing figure 1-25 Topology for Lab 1-1

Page 36

Missing figure 1-26 Topology for Lab 1-2

Page 41 Task 11 Configure the IP host statements on router GAD Lab

Step

Error

Corrections

comment

Lab 1.2.3 Review of Basic Router Configuration with RIP

Task 11 Configure the IP host statements on router GAD

GAD(config)#ip host BMH 172.18.0.1 172.17.0.1.

GAD(config)#ip host BHM 172.18.0.1 172.17.0.1.

Change typo from BMH to BHM

CHAPTER 2 Missing several figures or answer figures are in place of empty boxes. Replacement PDF Chapter available online at www.ciscopress.com/title/1587131714 Suggest tearing out entire chapter and replacing with the PDF copy Page 73 74 74 74 75 75 75 76 77 78 79 80 83

Figure # 2-1 2-1a 2-1b 2-1c 2-1d 2-1e 2-1f 2-1g 2-2 2-3 2-4 2-5 2-6

Issue in First Printing Missing figure The answer figure is shown, should be an empty box The answer figure is shown, should be an empty box The answer figure is shown, should be an empty box The answer figure is shown, should be an empty box The answer figure is shown, should be an empty box The answer figure is shown, should be an empty box The answer figure is shown, should be an empty box Missing figure Missing figure Missing figure Missing figure Missing figure

84 84 85 87 91 97 102 106 110 115 122

2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17

The answer figure is shown The answer figure is shown The answer figure is shown Missing figure Missing figure Missing figure Missing figure Missing figure Missing figure Missing figure The answer figure is shown

Page 90 Task 6 Configure OSPF Routing on Router Rome Step

Error

Correction

Comment

Step 1

Rome(config)#router ospf 1 Rome(config-router)#network 192.168.1.0 0.0.0.255 area 0 Rome(config-router)#network 192.168.15.0 0.0.0.3 area 0

Rome(config)#router ospf 1 Rome(config-router)#network 192.168.0.0 0.0.0.255 area 0 Rome(config-router)#network 192.168.15.0 0.0.0.3 area 0

Change typo in the lab book from 192.168.1.0 to 192.168.0.0

Step 3

Rome(config)#router ospf 2

Rome(config)#router ospf 1

Change typo in the lab book from 2 to 1

Page 115 Table 2-14 Lab 2-7 Addressing Scheme Device

Interface

IP Address

Subnet Mask

RTA

Fa0/0 S0/1 S0/0 Lo0 S0/1 Fa0/0 S0/0

192.168.1.1 192.168.1.245 192.168.1.254 209.165.202.129 192.168.1.246 192.168.1.65 192.168.1.249

255.255.255.192 255.255.255.252 255.255.255.252 255.255.255.255 255.255.255.192 255.255.255.192 255.255.255.252

RTB

Correction: Change RTB S 0/0 mask from 255.255.255.192 to 255.255.255.252

CHAPTER 6 Page 229 Figure 6-15 - Figure is up above the beginning of the lab in the middle of the previous lab's text

CHAPTER 8 Page 268 Task 16: Test the VLANs Step 1. Ping from the host in port 0/4 to the host in port 0/8.

Was the ping successful? Why? Step 2. Ping from the host in port 0/8 to the host in port 0/4. Was the ping successful? Step 3. Ping from the host in port 0/4 to the switch IP 192.168.1.2. Was the ping successful? Step 4. Ping from the host in port 0/8 to the switch IP 192.168.1.2. Was the ping successful?

Correction: Port 0/4 should be change to port 0/5

CHAPTER 9 Page 292

Page 294

The switch prompt in Task 5 under the “2900 Switch” should be change from Switch_A(config)#exit To – Switch_A(vlan)#exit TASK 12 Create the ISL Trunk

Error

Correction

Comment

Switch_A(config)#interface fastethernet 0/1 Switch_A(config-if)#switchport mode trunk Switch_A(config-if)#switchport trunk encapsulation isl

Switch_A(config)#interface fastethernet 0/1 Switch_A(config-if)#switchport trunk encapsulation isl Switch_A(config-if)#switchport mode trunk

If you are using 3550 switch, you need to setup encapsultion before setup the port as trunk port.