USB/Ipod Music Player, Bluetooth handsfree USB/Ipod Music Player ...

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden

Instruction No 31310093

Version 1.3

Part. No. 31285547

USB/Ipod Music Player, Bluetooth handsfree

© Volvo Car Corporation

USB/Ipod Music Player, Bluetooth handsfree- 31310093 - V1.3

Page 1 / 56


Equipment

IMG-242205

A0000162

IMG-239664

IMG-332314

IMG-246925

IMG-333125



Page 2 / 56


IMG-331666



Page 3 / 56


IMG-333126



Page 4 / 56


INTRODUCTION

Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Note! This installation instruction shows the installation of the USB/iPod adapter and Handsfree with Bluetooth on left-hand drive vehicles. When installing in right-hand drive vehicles the steps are performed on the opposite side and/or mirrored. The right-hand drive design is also shown with text and pictures when operations differ. When installing Velcro fasteners/tape the underlying surface must be kept at a temperature of at least +20° C (68°F). The cable between USB/iPod adapter and music player can be ordered for USB, iPod, or both. Wiring A is for vehicles with an internal amplifier that is located in the media player. Wiring B and C are for vehicles with an external amplifier, located on the left-hand side of the cargo compartment. Cars with Performance Sound have internal amplifier. Cars with the High Performance and Premium Sound audio systems have external amplifier. There may be components in the accessories kit that are not used for this installation. Place the manual for this accessory in a suitable place in the vehicle.

Preparations



Page 5 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 1

Preparations

Turn the ignition key to position 0.

Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment.

IMG-245980

2 Open the glovebox. Carefully pry off the panel at the rear of the centre console. Use a plastic weatherstrip tool. The panel is attached by two clips on each of the short sides. Pull the panel away downwards.

J8504532



Page 6 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 3 Apply tape to the center console to protect it during removal and installation of the glove compartment.

IMG-239762

4 Remove the panel.

IMG-240082



Page 7 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 5 Detach the clip holding the vent from the glove compartment.

IMG-244221

6 Remove the rubber mat from the glovebox. Remove the 5 x screws from the opening. Pull the glovebox straight back in the vehicle in order to release the hidden clips, 2 pcs, in the top edge. Remove the outer section of the glovebox.

J8803318



Page 8 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 7 Unplug the connectors on the top.

IMG-222669

8 Remove the screws for the vent. Pull off the vent to the right and place to one side.

IMG-239763



Page 9 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 9 Remove the clips at the rear edge of the soundproofing panel and remove it.

J8504871

10 Remove the surround around the display and media player: Press in the catch at one of the surround's upper corners. Use a small screwdriver. Carefully pry off the surround on the same side. Use a plastic weatherstrip tool.

Note! Do not damage the panel and dashboard.

Repeat the procedure for the other side and then fold the surround backwards into the vehicle. Pull the surround up until it detaches.

J8504893

Hint If the panel is difficult to remove, press the panel on both sides again and repeat the procedure starting at the other side.



Page 10 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 11 Remove the ignition control module (ICM). It is secured by hidden clips, 2 pcs.

Hint Grip with both hands and pull.

Disconnect the two connectors. Put the display to one side.

J8504534

12 Detach the hand brake panel by pulling it carefully sideways.

IMG-263205



Page 11 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 13 Fold up the tunnel console's armrest and remove the cover at the bottom.

IMG-273610

14 Loosen the rear edge of the panel, it should not be completely removed.

IMG-273611



Page 12 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 15 Remove the two screws.

IMG-273630

16

Applies to all models

Remove the two screws along the front edge of the tunnel console.

IMG-270744



Page 13 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 17 Remove the front storage compartment by prying it off at the front edge using a weatherstrip tool and lifting it out.

IMG-263505

18 Carefully lift the catches at the front edge of the tunnel console.

Hint Use special tool, P/N 9995919.

IMG-263586



Page 14 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 19 Hold up the lock catch and at the same time slide the entire tunnel console back 20 mm, so that the two rear screws in the centre console are accessible.

IMG-263587

20 Remove the two screws.

IMG-263589



Page 15 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 21 Applies to cars with manual gearbox

Remove the gear selector lever boot from the center console. First pry it off at the front edge using a weatherstrip tool and then unhook it at the rear edge.

IMG-270745

22 Remove the two screws holding the centre console's panel to the dashboard. Loosen the connector to the centre console at the rear. Remove the center console.

IMG-240085



Page 16 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 23 Lift up the tunnel console and pull it back slightly. Unplug the big gray connector at the front.

IMG-268148

24 Lift out the console and turn it upside down

Note! Protect hand brake and gear lever when removing and installing the tunnel console.

IMG-269724



Page 17 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 25 Unplug the connector of the 12V socket.

IMG-263592

26 Carefully bend loose the tunnel console's rear panel using a weatherstrip tool.

IMG-263593

Installing the USB / iPOD cable



Page 18 / 56


Installing the USB / iPOD cable

Get the USB/iPod cable from the kit, insert the straight contact in the trailing edge of the tunnel console and into the storage compartment.

IMG-263595

28 Measure the length of the cable that is to be protrude from the bottom of the storage compartment.

IMG-263597



Page 19 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 29 Clamp in the cable harness to the existing cable harness using cable ties.

IMG-263598

30 Push on the panel, ensuring the cable is not pinched.

IMG-263599



Page 20 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 31 Reinstall the panel.

IMG-263600

32 Connect the connector to the 12V socket.

IMG-263601



Page 21 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 33 Fold the carpet to the right of the center console.

IMG-263604

34 Applies to cars with internal amplifier

Remove cable harness (A) from the kit. Applies to cars with external amplifier

Remove cable harness (B) from the kit. Applies to all cars

Route the cables on the right-hand side of the centre console.

Note!

IMG-273643


The fibre cables must not be bent with a radius less than 25 mm (1"). Make sure the cables are routed so there is no risk of wear.


Page 22 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 35 Applies to cars with internal amplifier

Take the relay and two thick pieces of foam tape from the kit. Connect the connectors from cable harness A to the mute relay. Tape the foam tape pieces around the relay.

IMG-239782

36 Applies to cars with internal amplifier

Place the relay between the white metal bracket (1) and the climate unit, high up on the bulkhead partition.

IMG-273613



Page 23 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 37 Take the adapter and 2 pieces of foam tape from the kit. Bend in the bracket at each end.

IMG-333128

38A Illustration A Illustration B

Remove the protective film on the foam tape and attach as illustrated.

IMG-333130

38B

IMG-262109



Page 24 / 56


39 Connect the USB/iPod connector and the fibre optic cable's connector to the adapter. Clamp the USB/iPod cable at the eyelet on the adapter using a tiestrap.

IMG-263611

40 Place the adapter between the carpet and the climate control unit as illustrated.

Note! Do not damage the fibre optic cable.

IMG-273668



Page 25 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 41 Connect the gray connector (1) in the new cable harness to the corresponding socket in the media player. Connect the gray connector (2) in the new cable harness to the gray connector (3) which was detached from the media player. Plug in the connector (4) on the adapter cable's fibre cable to the media player. Plug in the remaining connectors (5) on the fibre cables to each other. Plug in the remaining connectors that were disconnected from media player. Take a 700 mm (27 9/16") long piece of foam tape and cut into three equal pieces. Tape around the connectors (2) and (3). And a little around the connectors (5). IMG-273669

42 Position the connectors to the left in the opening so that they are not in the way when the media player is installed. Plug the remaining connectors which where detached into the media player. Reinstall the media player and secure it.

IMG-263624

Installing the microphone



Page 26 / 56


Installing the microphone

Unhook the sun shield from the bracket. Do this on both sides.

IMG-253963

44 Remove the locking plug and bracket. Do this on both sides.

IMG-274304



Page 27 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 45 Pull off the driver's weather strip at the A-post and dashboard. Pull off the panel from the A-pillar. The panel is secured by three clips. Unhook the safety clip. Lift the panel upwards and inwards in the vehicle. Remove the panel.

J8504996

46 Remove the interior lighting by grasping the front edge and pulling downward. It is held in place by six catches.

IMG-253982



Page 28 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 47 Remove the three screws.

IMG-253984

48 Take two 700 mm (27 9/16") pieces of foam tape from the kit. Cut one piece of the foam tape in half. Tape one long and one short piece of foam tape on the microphone cable starting 70 mm (2 3/4") from the microphone.

IMG-253985



Page 29 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 49 Pull down the headlining with the interior lighting frame slightly. Route the microphone cable along the top of the existing cable harness as illustrated.

IMG-253986

50 Route the microphone cable to the front edge of the headlining as illustrated.

Note! Position the cable so that it is not pinched when the sun visor mounting is refitted.

IMG-253989



Page 30 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 51 Make a mark on the foam tape which is attached to the cable, 230 mm (9 1/16") from the microphone. Use a cable tie to fasten the cable at the mark at the existing connector. Install the three trim screws.

IMG-274305

52 Hold the microphone cable straight forward and refit the interior lighting.

IMG-253991



Page 31 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 53 Clean the area on the microphone and headlining panel as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Dry with care, do not rub. Allow to dry.

Note! In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent.

IMG-331708

Remove the backing tape from one side of the Velcro strip and press it onto the microphone.

54 Remove the remaining backing tape from the Velcro strip and press the microphone securely onto the ceiling panel as illustrated.

Note! Direct the microphone towards the driver.

Feed in any cable excess.

IMG-253993



Page 32 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 55 Route the cable to the A-pillar and onwards to the glove compartment. Take three small tie straps from the kit and secure the cable at the A-pillar as illustrated. Refit the sun visor mountings. Reinstall the A pillar panel and weatherstrip.

IMG-253994

Installing the control panel

56

Installing the control panel

Clean the area on the centre console as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Dry with care, do not rub. Allow to dry.

Note! In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent.

IMG-331708



Page 33 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 57A A

Place the control panel cable in the groove as illustrated. B

IMG-331669

57B

IMG-331670

58 Remove the protective film from the tape and secure the control panel edge to edge against the climate panel and according to the dimensions illustrated.

IMG-331707



Page 34 / 56


59 Press the cable securely into the compartment that is in the joint between the front and rear side of the center console. Stop level with the lower edge of the display opening.

IMG-240872

60 Route the cable from the control panel on the right-hand side of the centre console.

IMG-273676



Page 35 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 61 Reinstall the tunnel console, but do not slide it forward so far that it covers the rear screw holes for the centre console's panel. Plug in the connectors at the leading edge.

Note! Protect the hand brake and gear shift when fitting the tunnel console.

IMG-263602

62 Install the centre console, connect the green connector and fit the screws, two at the top and two on the rear edge. Applies to cars with manual gearbox

Install the gear selector boot in the center console starting at the rear edge.

IMG-273679



Page 36 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 63 slide the tunnel console forward so that the locking lug secures it. At the same time, guide in the floor carpet on the left-hand side. Reinstall:

the two screws at the front edge of the tunnel console. the panel at the parking brake.

IMG-263629

64 Reinstall the screws

IMG-263632



Page 37 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 65 File a slot at the rear of the storage compartment's bottom cover for the USB/iPod cable in the position as shown.

IMG-263635

66 Place the USB/iPod cable in the bottom cover's slot and pres it into place.

IMG-263637



Page 38 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 67 Reinstall:

the ignition control module (ICM) with the connectors, screws and frame. front storage compartment inside of the center console.

IMG-263636

Installing the control module

68

Installing the control module

Take the cable harness and control module from the kit. Connect the cable harness to the control module (1). Lock the catch (2).

IMG-250303



Page 39 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 69 Get a thick foam tape from the kit and fasten it on the front of the control module. Fold up the foam tape around the corners and edges of the control module.

IMG-256724

70 Get three small pieces of foam tape from the kit and fasten these on the back of the control module.

IMG-256725



Page 40 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 71 Detach the front sill molding by first pulling it backwards at the front edge and then straight up so that the clips release.

IMG-250923

72 Unscrew the clips holding the floor carpet. Fold aside the floor mat to access the bulkhead panel inside.

Note! Take care not to create folds in the carpet.

J8504868



Page 41 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 73 Place the control module with the thick foam tape forward, against the bulkhead.

IMG-256726

74 Fold aside the cable harnesses (1) so that they do not end up between the control module and floor mat. Route the control module's cable harness under the cable harnesses (2) and on toward the tunnel console. Fold back the carpet.

IMG-256727



Page 42 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 75 Connect the connectors for the Bluetooth system as illustrated: Applies to cars with internal amplifier

1. Connect cable harness A to the cable from the control module. Applies to cars with external amplifier

1. Connect cable harness B to the cable from the control module. Applies to all models

2. Connect the microphone 3. Connect the control panel IMG-239778

Take one of the cut pieces of foam tape and tape around the connectors.

76 Place the connectors and the excess wiring inside the center console. Fold back the carpet.

IMG-239781



Page 43 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 77 Take two large tie straps from the kit and secure the cable from the microphone on top of the collision pipe. Applies to cars with external amplifier

Also secure the cable harness B, that is to be later routed back to the external amplifier.

IMG-248570

Steps 78-98 apply to cars with external amplifier

78

Steps 78-98 apply to cars with external amplifier

Grasp the upper edge of the right-hand side cushion. Pull the side cushion forward so that the clip on the reverse releases. Slide the side cushion up. Remove the side cushion. Repeat the operation on the other side.

J8504708



Page 44 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 79 Pull off the rubber strip at the rear of the opening for the righthand rear door. Carefully pry off the lower panel on the C-post on the right-hand side. Carefully pry at the top edge. Use a plastic weatherstrip tool. Pull the panel on the C-post so that the two upper clips release. Then continue down until the last two clips release. Remove the panel on the C-post.

J8504585

80 Pull the top edge of the sill trim panel in the right-hand rear door inwards until the clips on the inside release. Then continue down and pull the panel upwards until the remaining two clips on the underside release.

J8504733



Page 45 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 81 Pull off the rubber mouldings at the rear edge of the right-hand front door and at the front edge of the right-hand rear door. This releases the lower panel on the B-pillar. Pull the bottom edge of the lower panel on the B-pillar until the two bottom clips release.

J8504735

82 Fold the rear seat cushions and backrest forwards.

IMG-240925



Page 46 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 83 Applies to the V50

Remove the cargo compartment carpet.

J8504575

84 Use a weatherstrip tool and pry up one corner of the sill trim panel so that the two clips on the short side release. Pull up the sill trim panel so the remaining six clips release. Remove the panel. Detach the rubber strip where it covers the left and right-hand side panel in the tailgate opening.

IMG-240926



Page 47 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 85 Remove the screw. Pull the panel upwards so that the four clips on the inside release. Remove the panel. This must be carried out on the left-hand side on right-hand drive vehicles.

IMG-240927

86 Fold out the load securing eyelets. Insert a scriber with an angled tip into the holes in the top of the covers (1). Turn the scriber so that the tip engages the reverse of the cover. Pull the covers off. Remove the screws in the load securing eyelets. Remove the screw (2). Pull off the side panel at the top so that the two clips at the rear/bottom of the side window and the clip at the bottom of the D-post release. Disconnect the connector for the 12V socket, if present. This is carried out on the left-hand side on right-hand drive vehicles. J8504570



Page 48 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 87 Applies to S40 (04-)

Remove the cargo compartment carpet.

J8504553

88 Remove the upper floor support on the left and right-hand sides if applicable.

J8504552



Page 49 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 89 Unscrew the two external clips at the front edge/bottom edge of the sill trim panel on the tailgate. Use a weatherstrip tool and pry up one corner of the sill trim panel so that the two clips in that end release. Pull up the sill trim panel at the other end so that the remaining two clips release. Remove the sill trim panel.

J8504554

90A Illustrations A and B

Remove the four clips (1), in illustration A, holding the side panel in the bodywork. Unhook the front edge of the parcel shelf panel at the mounting (2), in illustration A. Pull the side panel away from the parcel shelf panel and the panel on the C-post. Unhook the side panel from the mounting (3), in illustration B, on the underneath of the parcel shelf. Disconnect the connector for the 12V socket, if present. Unhook the side panel from the load securing eyelets (4), in illustration A. Remove the side panel.

J8504584

This is carried out on the left-hand side on right-hand drive vehicles.

90B

IMG-240928



Page 50 / 56


91 Applies to the S40 and V50

Route the cable (B) inside the floor carpets, the lower B-post panel and the insulation panels, back to the rear edge of the right -hand rear wheel arch. Route the cable along the existing cable harnesses in the cargo compartment.

Note! Ensure that the cable is positioned so that there is no risk of it catching or rubbing.

IMG-243266

92 Applies to the S40 and V50 (not right-hand drive)

Continue routing the cable harness to the amplifier. Position the cable harness at the existing cable harness to the side and at the rear edge of the cargo compartment, all the way from the right-hand wheel arch to the amplifier. Take a short tie strap from the kit and secure the cable harness at the existing cable harness.

IMG-240929



Page 51 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 93 Applies to the V50

Remove the clips and the insulation panel.

J8504639

94 Disconnect the rear connector (1) on the amplifier.

IMG-240930



Page 52 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 95 Remove cable harness (C) from the kit. Connect the cable harness to the amplifier as follows: Connector (1) which is disconnected from the amplifier is connected to the female connector (2) on the cable harness. Connector (3) on the cable harness is connected to the amplifier. Tape one section of the cut piece of foam tape around connectors (1) and (2). Secure the excess cable using one of the cut up parts of foam tape and two short tie straps, on the existing cable harness of the vehicle

IMG-240931

96 Applies to the V50

Reinstall the insulation panel on the left-hand side. Applies to the S40 and V50

Take the relay and 2 thick pieces of foam tape from the kit. Connect the connector from cable harness C and the routed cable harness connector to the relay. Fit 2 pieces of tape around the relay.

IMG-239782



Page 53 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 97 Place the relay behind the existing cable harness.

IMG-240932

98 Reinstall the connectors to the rear section of the glove box. Note the color marking on the cable for the right-hand connector.

IMG-231504

Reinstall:



Page 54 / 56


Reinstall:

Dashboard

the lower vent. the sound proofing. the rear section of the glovebox by guiding it in diagonally inside the center console. Then straight forward. The rear section must be positioned on the outside of the remaining inner section. the clip for the vent on the glovebox. the panel on the dashboard end face. Remove the tape. IMG-228142

the panel above the centre console. Check that the cable to the control panel is not pinched. Passenger compartment

the B-pillar panel. the sill trim panels. the C-pillar panel. the rubber strips in the door openings. side cushions. Position the backrest and seat cushions back into place. Cargo compartment

the side panels. the screws in the load securing eyelets. Tighten to 24 Nm (18 lbf.ft.) (applies to the V50). the sill trim panel for the tailgate. the upper floor support if applicable (applies to the S40). the cargo compartment carpet.



Page 55 / 56

Installation instructions, accessories Volvo Car Corporation Gothenburg, Sweden 100 Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.

IMG-242268

101 Turn the ignition key to position I. Turn on the radio. Check that the control panel for Bluetooth lights up. Press the button (1) in the middle of the control panel. The radio should mute and a voice should be heard. Press the button (2). The voice should now stop and the audio from the radio returns.

IMG-331671



Page 56 / 56

USB/Ipod Music Player, Bluetooth handsfree USB/Ipod Music Player ...

USB/Ipod Music Player, Bluetooth handsfree USB/Ipod Music Player ...

Suggest Documents

IRJET- EMO Player: Emotion based Music Player

Cheap Music Player Music Digitizer Record Analog Music In Usb ...

Handsfree & Music Streaming

Handsfree & Music Streaming

SeeedStudio Arduino Music Player Shield - datasheet-int109b2p.pdf ...

AGPTek Longevity Music Player A02 User Manual

AGPTek Longevity Music Player A02 User Manual

Mechanical Music Digest - Archives - Player-Care.com

Personalized affective music player - UT Research Information

SmartDJ, An Interactive Music Player for Music ...

The Jazz Piano Player - Faber Music

## Player ## Player

FISCON Bluetooth Handsfree - Bilkomponenter.no

PDF DOWNLOAD Music Theory for the Bass Player - Google Sites

James Brown Bass Player Now Accepts New Music ... - Newswire.net

iPod Distraction: Effects of Portable Music-Player ... - Computer Science

The Prevalence of Using Personal Music Player and ...

A location based music player for sports 1

Cheap Usb Cassette Audio Music Player And Converter Convert Old ...

An HTML5 Interactive (MPEG-A IM AF) Music Player

XPOD - A human activity and emotion aware mobile music player

Linn Klimax DS digital music player installation - Clever Home ...

[PDF] Download Music Theory for the Bass Player - Google Sites

PDF Music Theory for the Bass Player: A ... - Google Sites