User Manual - my doorbots

User Manual

Table of Contents DoorBot Features.................................................2 In the Box.............................................................5 Technical Specifications........................................6 Technical Requirements........................................7 Wi-Fi Setup..........................................................8 Removing DoorBot from a Network......................11 Installation............................................................12 Charging the Battery.............................................19 Camera Rotation...................................................20 Mobile Application..................................................21

1

DoorBot Features 1

1. Microphone 2. Night Vision LED’s

2

3. VGA Camera (640x480)

3 4

4. Adjustable Camera Housing 5. Brushed Aluminum Faceplate

5

6. LED Ring 7. Button

6 7

8. Speaker

8

2

DoorBot Features 9 10 11

9. Reset Button

12

10. Micro-USB Charging Port 11. Bracket Contacts 12. Camera Rotation Port 13. Security Screw

13

3

DoorBot Features 14 15

14. Bracket Coupler

16

15. Conductive Gasket

17

16. Terminal 17. Installation Screw port 18. Wire Management Track

18

19. Doorbell Wiring (not provided)

19

4

In the Box Drill Bit

Level

Double-End Screw Bit

DoorBot

Mounting Bracket

Screwdriver

Additional Components: Micro-USB Charging Cord, Sealing Tape, Threaded Screws, Aluminum Siding Screws, Wall Anchors, Quick Install Guide

5

Technical Specifications 2.39”

1.30”

5.68” Weight: 8.1oz Battery: 3500 mAh Power Input: 8-24 VAC (wired) 5 VDC @ 500mA (micro-USB) Video: 640 x 480 VGA Operating Temperature: 5-122 °F Weather Resistant

6

Technical Requirements High Speed Internet: DSL, Cable or FiOS (for optimal performance)

Wi-Fi: 802.11b 2.4 GHz Web Browser: Internet Explorer 7+ Google Chrome Firefox 3+ Safari 3+

Setup:

iOS 6+

Android 2.3+

Session Processing:

iOS 6+

Android 2.3+

Note: DoorBot may work with legacy software as long as the user’s smart device is connected to a W-Fi network. Certain functionality may be limited without connection to a Wi-Fi network.

7

Connecting DoorBot to a wireless network Choose a descriptive name for your DoorBot (e.g. Eric’s Front Door).

Choose the timezone in which your DoorBot will be located in.

STEP 1 Press the DoorBot to begin setup.

8

STEP 2 Connect to the DoorBot Network.

STEP 3 Choose a network for your DoorBot to connect to.

NETWORK NAME

SIGNAL STRENGTH

User’s Wi-Fi Network Another Network Another Network

9

SECURE

REFRESH

STEP 4 Now that you've established a connection for DoorBot, go ahead and reconnect to your personal Wi-Fi network.

User’s Wi-Fi Network

SUCCESS! The setup process is complete once you've connected back to your personal Wi-Fi network.

10

Removing DoorBot from a Wi-Fi Network To change the Wi-Fi network that your DoorBot is connected to, press the reset button on the back of the device. Once reset, you'll need to follow the steps in the Quick Install Guide before you can continue using your DoorBot.

RESET BUTTON

11

Installation DoorBot can be mounted to wood, stucco, brick, concrete, or aluminum siding. Included in the package are all of the tools necessary to mount your DoorBot. If you plan on connecting DoorBot to your wired doorbell, follow the instructions labeled Wired, otherwise follow the Wireless steps to complete installation.

STEP 1 First, you want to make sure that you have WiFi at your door. Place your smartphone or tablet on the exterior wall that you intend to mount DoorBot. If you see a Wi-Fi connection then proceed with the installation. JUMP TO STEP 4 TO CONTINUE WITH WIRELESS INSTALLATION

12

STEP 2 (WIRED INSTALLATION ONLY) Now find the outlet or circuit breaker to turn off power to your wired doorbell.

STEP 3 (WIRED INSTALLATION ONLY) Unscrew the doorbell button and detach the wires from the back of the doorbell.

13

STEP 4 Press the mounting bracket against the wall ensuring it is level with the included level attachment and mark off screw holes. If wiring your DoorBot, you'll want to make sure the doorbell wires are near the center of the bracket.

JUMP TO STEP 6 TO CONTINUE WITH WIRELESS INSTALLATION

STEP 5 (WIRED INSTALLATION ONLY) Create a small slit in the center of the provided sealing tape. Then gently pull the pre-existing wiring out from your wall and through the slit in the sealing tape.

1

2

14

3

STEP 6 - ON BRICK/STUCCO/CONCRETE Once you have your mounting bracket marked off, drill 4 holes into the wall with the provided drill bit.

2

1

CONTINUED Screw the provided threaded screws into the wall anchors until they're completely in the wall and the mounting bracket is flush against the wall.

3


15

ON ALUMINUM SIDING Screw in the provided aluminum siding screws into the screw holes on the mounting plate, through the aluminum siding, and into the wood backing.


ON WOOD Screw in the provided threaded screws into the screw holes on the mounting plate, and through the wood surface.


16

STEP 7 (WIRED INSTALLATION ONLY) Take the doorbell wires and attach them to the terminals mounted at the top of the mounting bracket by tightly winding the wire around the exposed screw shaft. It does not matter which wire goes to which terminal.

STEP 8 Prior to mounting DoorBot, take the included screwdriver and place it in the camera rotation port located on the back of the device. Using the screwdriver like a joystick, adjust the camera angle as needed.

1

2

17

STEP 9 Mount your DoorBot on the bracket by hooking it over the bracket coupler.

Use the provided screwdriver and proprietary bit to secure the screw at the bottom of the DoorBot. At this point you may now restore power to your doorbell circuit. (wired installation only)

18

1

2

Charging the Battery Your DoorBot should come fully charged and last for over a year. You can view the battery life through the mobile app. To recharge your DoorBot, simply remove it from the mounting bracket and use the included micro-USB charging cord. The LED ring will blink as it charges, and then stop once fully powered.

MICRO-USB CHARGING PORT

is not necessary to charge * ItDoorBot when connected directly to a wired doorbell.

19

Camera Rotation Prior to mounting DoorBot, take the included screwdriver and insert it in the camera rotation port located on the back of the device. Using the screwdriver like a joystick, adjust the camera angle as needed.

30° END-TO-END CAMERA ROTATION AND

123° FIELD OF VIEW

20

Mobile Application SETUP A DOORBOT Choose a descriptive name for your DoorBot (e.g. Eric’s Front Door) and which timezone it will be in.

21

SETUP A DOORBOT - STEP 1 Press the DoorBot button to begin setup.

22

SETUP A DOORBOT - STEP 2 Exit out of the app and connect to the DoorBot network.

23

SETUP A DOORBOT - STEP 3 Launch the app and select your Wi-Fi network to complete setup.

24

MY DOORBOTS The My DoorBots page displays each DoorBot that you own and is connected to a Wi-Fi network. Here you can monitor multiple components and features of DoorBot.

ON

DoorBot is live.

OFF

DoorBot is inactive and will not notify you when you have arriving guests. You can turn your DoorBot on by pressing this button.

LOW BATTERY

Notifies you when the battery is running low. You will also be notified via email.

ACCOUNT SETTINGS

Manage your password, log out of the app, or add a new DoorBot to your account.

DOORBOT DASHBOARD

Access specific information for each DoorBot.

25

DOORBOT HISTORY The DoorBot History page shows you the list of calls that were both answered and missed.

ANSWERED CALL

The call was answered by someone connected to that DoorBot.

MISSED CALL

The call was either never answered, or it was rejected.

RETURN

Return to My DoorBots Page.

26

DOORBOT SETTINGS Manage settings specific to that DoorBot.

27

ANSWERING DOORBOT DoorBot will send a push notification when you have a visitor. You'll be able to see your guests prior to accepting/declining the call.

28

ANSWERING DOORBOT If you choose to answer the call, you'll see some options/features within the app screen.

END CALL

MUTE SPEAKER

29