Volkswagen Golf V - Front door

20 downloads 12996 Views 1MB Size Report
Removing and installing. 58-1, Outer door plate, removing and installing. ▫ Edge protection. ▫ Between outer door panel and inner door part. Page 4 / 44.
Volkswagen Golf V - Front door

Page 1 / 44

57 - 1

Front door Tools

Special tools, testers and auxiliary items required „

Socket wrench T 10072

„

Assembly tool T 10118

„

Door adjusting wrench 3320

„

Joint for 3320 3320/1

„

Box wrench 3320/2

Front door

„

Box wrench 3320/3

„

Application roller for door insulation foil 3356

„

Torque wrench 550 Nm V.A.G 1331

„

Adjusting gauge 3371

Special tools, testers and auxiliary items required „

Cartridge gun V.A.G 1628

Page 2 / 44

Front door

Page 3 / 44

„

Cartridge heater V.A.G 1939 A

„

Trim removal wedge 3409

„

Assembly tool set T 10237

Materials

DH 009 100 01 1) 2)

1C- window adhesive

„

„

Glass primer/paint primer

„

Cleaning solution

„

Primer applicator

3) Materials 1) Observe

D 009 401 04 3) D 009 500 25 3)

are stored in box D 004 700.

minimum curing time

D 009 200 02 3)

57-1, Minimum curing

time 2) Heat

according to manufacturers instructions using cartridge heater V.A.G 1939 . Door construction, assembly overview

The door consists of inner door part - 6 and outer door plate - 1 - . Parts are joined by the front - 7 - and the rear - 5 - retaining tracks. Retaining tracks are bolted to inner door part and bonded to outer door plate. Inner door part - 6 - undertakes among other things the function of the previously known subframe. Loudspeakers, window regulators, window regulator motors, wires, window guide, exterior mirror and door lock are installed on inner door part. Outer door plate - 1 - is also bolted to inner door part on the lower edge.

Front door

Page 4 / 44

Exterior window shaft seal, insulation and outer door handle are installed on outer door plate. Caution! Various bolts are used to secure the outer door plate. Outer door plate is damaged if not allocated correctly.

„

Outer door plate „

„

Removing and installing 58-1, Outer door plate, removing and installing

Edge protection „

Between outer door panel and inner door part.

Front door

„

„

Screw „

Characteristic: Bolt has point and thinner washer.

„

6 pieces on lower edge

„

2 piece in rear rail area

„

10 Nm

Rear retaining track „

„

„

„

Characteristic: Bolt without point but with thick washer.

„

Qty. 10 for both retaining tracks on 4-door version

„

Qty. 11 for both retaining tracks on 2-door version

„

14 Nm

Inner door part

„

Assembly overview 57-1, Inner door part, assembly overview

Front retaining track „

„

Adhesive: DH 009 100 03

Screw

„

„

Page 5 / 44

Adhesive: DH 009 100 03

Screw „

Characteristic: Bolt has point and thick washer

„

Qty. 1 for front rail area

„

10 Nm

Insulation „

Self-adhesive

Front door

„

„

To adhere, insulation must be preheated and then pressed on firmly

Clip „

„

Page 6 / 44

Qty. 6

Window shaft seal „

Must be installed before installing outer door shell.

Door hinges, assembly overview

Caution! The nut for eccentric pin - 9 - must not be loosened under any circumstances. It cannot be secured again using workshop equipment. Note : „

The description applies to the right side. The left side is derived accordingly from this.

„

Bolts for door hinges must always be replaced after loosening.

„

Hinges are no longer manufactured as separated parts.

Front door

„

„

Page 7 / 44

Door „

Removing and installing 57-1, Door, removing and installing

„

Adjusting adjusting

57-1, Door,

Guide bolt „

10 Nm

„

Door hinge with door arrester

„

Socket head bolt „

20 Nm + 1 / 4 turn further (90 )

„

Always replace bolts after

Front door

Page 8 / 44

loosening „

Socket head bolt „

Installed from the vehicle interior

„

Remove lower A-pillar trim

Repair Manual, Body Interior, Repair Group 70, Trim panels/insulation; Pillar and side trim „

20 Nm + 1 / 4 turn further (90 )

„

„

Always replace bolts after loosening

Socket head bolt „

20 Nm + 1 / 4 turn further (90 )

„

„

Always replace bolts after loosening

Socket head bolt „

20 Nm + 1 / 4 turn further (90 )

„

„

Guide screws „

„

10 Nm

Nut „

„

Always replace bolts after loosening

For the eccentric pin, must not be loosened. Used for making adjustments during production.

Door hinge

Front door

„

„

Page 9 / 44

Door hinge is no longer manufactured as separated parts.

Socket head bolt „

20 Nm + 1 / 4 turn further (90 )

„

„

Always replace bolts after loosening

Socket head bolt „

20 Nm + 1 / 4 turn further (90 )

„

„

Always replace bolts after loosening

Socket head bolt „

20 Nm + 1 / 4 turn further (90 )

„

Always replace bolts after loosening

Door, removing and installing

Note: „

Removing and installing is described only for the right door. Removing and installing the left door is derived accordingly from this.

Removing

Front door

- Release boots - 6 - by pressing on locking mechanism - arrow a - and remove boots from A-pillar. - Swivel locking lever - 7 - downward arrow b - and disconnect electrical harness connector - 8 - from connector station. - Remove screws - 4, 5 and 11 - using door adjustment wrench 3320 and bit insert 3320/3 from hinge. - Pull door in - direction of arrow - from guide bolts - 2 and 9 - . Installing

Installation is performed in the reverse order of removal. - Torque specification for screws - 4, 5 and 11 - : 20 Nm +

Page 10 / 44

Front door

1

/ 4 (90 „

Page 11 / 44

) additional turn.

Screws - 4, 5 and 11 - must always be replaced.

- Observe gap dimension of front door

Repair Manual, Body Collision Repair, Repair Group 00, Technical data; Body gap dimensions Door, adjusting

Warning! The nut for eccentric pin - 9 - must not be loosened under any circumstances. The nut cannot be secured again using workshop equipment.

Front door

Note : „

The door is properly adjusted when there is an overall even gap dimension when closed, it is not too far inward or outward and contours align.

„

Vehicle must stand on its wheels in order to be able to perform the adjustment.

„

If outer door plate is removed, window frame of inner door part must be adjusted in relation to roof frame and B-pillar, and to rear door.

- Observe gap dimension of front door

Repair Manual, Body Collision Repair, Repair Group 00, Technical data; Body gap dimensions For correct gap dimension adjustment, screws - 5, 7, 12 and 13 - at A-pillar must be loosened. For screw - 5 - , lower A-pillar trim must be removed

Repair Manual, Body Interior, Repair Group 70, Pillar and side trim . Other measures, such as aligning the door upward, are not effective. Excess pressure thereafter will again cause the door to sag. For correct alignment adjustment, screws - 4, 6 and 14 - and guide screws - 2 and 8 - must be loosened. Door adjusting wrench 3320 with bit insert 3320/3 must be used for this. Outer door plate, removing and installing Removing

Page 12 / 44

Front door

- Pry off clips - 3 - beginning at bottom of door - 1 - and remove cover - 2 - .

Page 13 / 44

Front door

- Removing lock cylinder installing - Remove door handle installing

Page 14 / 44

57-1, Housing, removing and 57-1, Door handle, removing and

- Remove screw - 1 - from bearing bracket - 2 - , located behind outer door plate.

- Remove all screws - 2, 3, 4 - . - Carefully remove outer door plate. Installing

Caution! Various bolts are used to secure the outer door plate. Outer door plate is damaged if not allocated correctly.

Front door

Page 15 / 44

- Carefully set outer door plate in. - Start all screws - 2, 3, 4 - . „

Make sure that the various bolts are used correctly. „

Characteristic for bolt - 2 - : Bolt has point and thinner washer.

„

Characteristic for bolt - 3 - : Bolt without point but with thick washer.

„

Characteristic for bolt - 4 - : Bolt has point and thick washer

- Check whether guide pins for retaining tracks are located in the corresponding guide holes of inner door part. Then

Front door

tighten all screws - 2, 3, 4 - . „

Observe the correct tightening torques for the various bolts.

Tightening torque for bolt - 2 - : 10 Nm. Tightening torque for bolt - 3 - : 14 Nm. Tightening torque for bolt - 4 - : 10 Nm. Further installation is performed in the reverse order of removal. New outer door plate, installing

Caution! Various bolts are used to secure the outer door plate. Outer door plate is damaged if not allocated correctly. Note: „

Observe the chapter of installation notes, bonding new outer door plate 57-1, Installation notes for adhering a new outer door plate

Page 16 / 44

Front door

„

Old (damaged) outer door plate with retaining tracks removed 57-1, Outer door plate, removing and installing

- Install front - 2 - and rear - 6 retaining tracks on inner door part. For this, use the "bolt without point with thick washer" . Torque for bolt - 3 - and - 5 - : 10 Nm. - Screw two guide screws into bottom edge of inner door part.

Page 17 / 44

Front door

The painted outer door plate is fitted first without applying adhesive. The assembly block from the assembly tool set T 10237 is needed to fit the outer door shell. One strip of "Tesa Power Strips large" - 6 - is affixed onto the lowered side. The pin has the minimum dimension for the gap width. The surface without adhesive is placed onto the neighboring component until it makes contact. - Adhere assembly blocks - 3 - to outer door plate. - Guide the outer door plate - 1 - in lower edge of inner door part via the guide bolts. - Using wedges - 4 - from assembly tool set T 10237 , adjust gap dimension to sill panel and outer door shell height.

Page 18 / 44

Front door

- Lay outer door panel with assembly blocks on adjoining components - 2 and 5- . - Check gap dimension with adjustment gauge 3371

Repair Manual, Body Collision Repair, Repair Group 00, Technical data; Body gap dimensions - If gap dimensions can no longer be adjusted, inner door part must be adjusted 57-1, Door, adjusting - Remove outer door plate again.

- Apply adhesive beads - 2 - onto front 1 - and rear - 3 - retaining tracks

Page 19 / 44

Front door

cartridge gun V.A.G 1628 .

The securing block from assembly tool set T 10237 is needed to insert outer door panel. Two strips of "Tesa Power Strips large" - 5 - are affixed onto contact surface. - Guide the outer door plate - 1 - in lower edge of inner door part via the guide bolts. - Bring outer door plate with assembly blocks - 3 - into contact with neighboring components. - Using wedges - 4 - from assembly tool set, adjust gap dimension to sill panel and outer door plate height. - Check gap dimensions with adjustment gauge 3371

Page 20 / 44

Front door

Repair Manual, Body Collision Repair, Repair Group 00, Technical data; Body gap dimensions - Affix short securing blocks - 2 uniformly onto door to be replaced and neighboring components. Note: „

A waiting time of 180 minutes must be observed before performing further work on the affixed door.

- Rest of installation is performed in the reverse order of removal 57-1, Installing Retaining track on outer door plate, removing and installing Removing retaining track

Caution! The following work must be performed very carefully. Since the outer door plate is to be re-used, dents and scratches must be prevented. When cutting through adhesive bead, always hold retaining track and outer door plate together as shown in the illustration. Otherwise, outer door plate flaps off the retaining track and must no longer be used again. Note: „

The following work is to be performed only with a second technician.

Page 21 / 44

Front door

Outer door plate with retaining tracks removed Removing

Page 22 / 44

57-1,

- Store the outer door plate - 1 - on a firm surface and protect outer door plate against scratches. - Secure spooling tool - 2 - . - Secure cord - 5 - onto spooling tool and retainer - 4 - . - Hold retaining track and outer door plate firmly together when cutting through adhesive bead. - Using cord, cut through adhesive bead from retaining track - 3 - and outer door plate - 1 - until slightly out over the center.

Front door

- After adhesive bead has been cut up to halfway in the first step, move the spooling tool - 2 - and insert cord - 5 on the side not yet cut. - Hold retaining track - 3 - and outer door plate - 1 - firmly together when continuing to cut through adhesive bead. - Cut through the second half of the adhesive bead. Installing retaining track

- Carefully, cut remaining adhesive bead on outer door plate up to the highest possible minimum without damaging paintwork while doing so. - Further work steps are described in chapter "installing new outer door plate" 57-1, New outer door plate, installing . Note: „

"Installation notes for adhering new outer door plate" are also to be followed to install a new retaining track.

- Install a new retaining track onto inner door part on location of the removed retaining track. - Apply adhesive onto the new retaining track. - Firmly bolt door plate on lower edge and on the retaining track. - Secure outer door panel to new retaining track with securing blocks. Installation notes for adhering a new outer door plate

Note: „

If both outer door plates must be replaced on a side, follow the sequence. First the rear outer door plate and then the front outer door plate is aligned and adhered. For alignment of rear outer door panel to front outer door panel, adhere long securing blocks.

„

If the cataphoretic paint coating of outer door plate is damaged on the inside in the adhesion area, or was damaged there, this area must be primed using glass/paint primer D 009 200 02.

„

1K window adhesive DH 009 100 must be heated for

Page 23 / 44

Front door

Page 24 / 44

20 minutes in cartridge heater V.A.G 1939 A . - Clean application surfaces on retaining tracks with cleaning solution D 009 401 04.

- Apply adhesive material using cartridge gun V.A.G 1628 onto application surfaces at a right angle to the retaining track. Warning! Outer door plate must be installed within 10 minutes, otherwise bonding properties of adhesive will be impaired. „

Place outer door panel on retaining tracks with help of both assembly blocks, center with wedges and adjustment gauge 3371 and press assembly block application surfaces onto surrounding components.

„

Secure outer door panel during curing time with securing blocks.

„

After installing, align outer door plate to the other components and gap dimensions must be uniform.

„

If the adhesive bead has been applied too thickly and the adhesive expands out between retaining track and outer door plate, then the excess adhesive must be removed.

Minimum curing time

Warning! Special requirements must be fulfilled for replacing bonded outer door plates. One of these standards for

Front door

example is, that a freshly bonded outer door plate must comply with the safety elements, even in an accident, once the adhesive has exceeded the prescribed curing time. The minimum curing time for outer door panel with 1K adhesive DH 009 100 is 180 minutes. By minimum curing time, it is meant the time from bonding in the outer door plate up to use in the vehicle, or until further work can be performed. During this time, the vehicle must stand on an even surface at room temperature (at least 15 C). Warning! The vehicle is operationally ready only after the minimum curing time has elapsed. Cleaning when soiled by adhesive sealing material

- It is recommended to use adhesive remover D 002 000 10 as a cleaning solution. Observe safety precautions when processing. Caution! When cleaning the vehicle, outer door plate bonded in immediately beforehand must not be shifted. - First clean paint surface coarsely using a dry rag. Eliminate remaining soiling using adhesive removal solution D 002 000 10. - Clean plastic trim: Allow adhesive sealing material to harden (about 1 hour) and then peel off. Inner door part, assembly overview

Note : „

The description applies to the right side. The left side is derived accordingly from this.

Page 25 / 44

Front door

Page 26 / 44

„

Inner door part

„

Window shaft seal

„

Loudspeaker

„

Window regulator motor „

„

removing 64-2, Window regulator motor, removing and installing

Insulation „

4x

„

20 mm x 40 mm commercially available cloth reinforced adhesive tape

Front door

Page 27 / 44

Door handle and door lock, assembly overview

Note : „

The illustration shows the left side. The right side is similar and can be determined from this.

„

Door lock „

„

Cable „

„

Removing and installing 57-1, Door lock, removing and installing

For disengaging lock of exterior door handle.

Screw

Front door

„

„

For securing lock to inner door part

„

18 Nm

„

Qty. 2

Mounting bracket „

„

Removing and installing 57-1, Bearing bracket, removing and installing

Screw „

„

Page 28 / 44

For lock cylinder.

Bolt „

Not available on all versions.

„

This screw is installed for additional securing of mounting bracket.

„

Backing

„

Lock cylinder housing

„

„

„

Only on drivers side.

„

Only one housing is installed on front passengers side.

„

Removing and installing 57-1, Housing, removing and installing

Cover cap „

For the lock cylinder housing.

„

Is secured to lock cylinder housing with three tabs.

Key „

Changing battery 57-2, Radio-frequency remote

Front door

Page 29 / 44

control key (foldable) battery - assembly overview „

„

Door handle with backing plate „

„

Not installed in Rabbit/GTI.

Cable „

„

Not installed in Rabbit/GTI.

Angle bracket „

„

Socket wrench T 10072

Expanding rivet „

„

Is a component of door handle.

Torx screw „

„

Removing and installing 57-1, Door handle, removing and installing

Backing „

„

Adapting new/additional keys to remote control and immobilizer 57-2, Adaptation of keys with radio-frequency remote control

To lock release mechanism of door handle.

Cover „

Does not belong to packaged contents of door lock

„

Is secured to door lock with three tabs.

Front door

Housing, removing and installing

Note: „

Removing and installing is described only for the housing. Removing and installing lock cylinder is derived accordingly from this.

Removing

- Pry out cover cap in front of bolt - 1 - . - Pull door handle - 2 - in - direction of arrow - and turn screw - 1 - with socket wrench T 10072 until housing - 3 can be removed. Installing

- Insert housing - 3 - in right angle - arrow - into door handle bearing bracket. Door handle - 2 - must make contact only lightly at door plate. - Install the bolt - 1 - into bearing bracket using socket wrench T 10072 . Door handle - 2 - engages again into housing - 3 - with a

Page 30 / 44

Front door

Page 31 / 44

very audible click. Note: „

During installation, housing must be pressed onto door plate. The door handle rests only lightly against the door panel.

Further installation is in reverse order of removal. „

Then a function test must be performed with door open, since the door cannot be opened if hood release cable is not correctly adjustment or clipped in.

Door handle, removing and installing

Note: „

Removing and installing is described only for the right door handle. Removing and installing the left door handle is derived accordingly from this.

Removing

- Remove housing installing .

57-1, Housing, removing and

- Pry out clip - 2 - from door handle - 1 - . - Swivel door handle - 1 - out of door - arrow - . Installing

Front door

- Guide assembly tool T 10118 into door through opening in inner door plate. - Light the inner part of door using a flashlight for better view. - Hook assembly tool T 10118 into spring - arrow A - . - Engage spring into door lock by pulling assembly tool T 10118 - arrow B - . Release lever is now locked in position. Note : „

Lock is secured by engaging spring in the operating lever. This prevents the cable from subsequently being clipped in at door handle incorrectly.

Page 32 / 44

Front door

Page 33 / 44

- Swivel door handle - 1 - into door. - Pull clip - 2 - into plate cutout and engage clip into door handle - 1 - - arrow - . Note: „

During installation, door handle - 1 - must be pressed onto door plate.

„

Clip - 2 - must engage into door handle - 1 - with a very audibly click.

Install housing „

57-1, Installing .

Then a function test must be performed with door open, since the door cannot be opened if hood release cable is not correctly adjustment or clipped in.

Bearing bracket, removing and installing

Note: „

Removing and installing is described only for the right bearing bracket. Removing and installing the left bearing bracket is derived accordingly from this.

Removing

Front door

- Remove lock cylinder housing Housing, removing and installing

Page 34 / 44

57-1,

- Remove door handle 57-1, Door handle, removing and installing - Remove outer door panel 58-1, Outer door plate, removing and installing - Pull retaining rubber - 4 - upward from guide pin. - Pull bearing bracket - 1 - in - direction of arrow - with guide pin - 2 - out of mounts - 3 - . Installing

Front door

- Slide bearing bracket - 1 - with guide pin - 2 - into mounts - 3 - . - Secure retaining rubber - 4 - on guide pin and mounting pin on bearing bracket mount. Further installation is in reverse order of removal. Door lock, removing and installing

Note: „

Removing and installing is described only for the right door lock. Removing and installing the left door lock is derived accordingly from this.

Removing

Page 35 / 44

Front door

- Remove outer door panel 58-1, Outer door plate, removing and installing - Remove mounting bracket 57-1, Bearing bracket, removing and installing - Disconnect connector - 5 - . - Remove bolts - 6 - . - Disengage cable - 1 - from actuator lever - 8 - and remove door lock - 4 - . Cover - 3 - is not supplied with delivery casing of door lock. Installing

Installation is performed in the reverse order of removal. Tightening torques for bolts: 18 Nm.

Page 36 / 44

Front door

„

Page 37 / 44

Then a function test must be performed with door open, since the door cannot be opened if hood release cable is not correctly adjustment or clipped in.

Side impact protection, assembly overview

Caution! The side impact member screws and nuts are painted during production. That means that the threads could shear off during removal with significant force. Loosening of screws and nuts should be avoided when possible

„

Side impact protection

„

Screw „

4x

Front door

„

Page 38 / 44

20 Nm

„

Insulation

„

Nut „

Qty. 2

„

20 Nm

Inner door seal

Inner door seals are equipped at the factory with sealant, applied to door flange and then rolled on. Note: „

During removal of the seal, sealant is distributed on interior side of seal and flanks are bent up easily. If the seal is re-installed, the sealing performance and proper seating are no longer guaranteed.

„

For this reason, every completely removed seal must be replaced with a so-called "hammer-stroke seal" .

„

For partially removed seals, seal flanks must be pressed together before installation.

Inner door seal, removing and installing

Note: „

Removing and installing is described only for the left inner door seal. Removing and installing the right inner door seal is derived accordingly from this.

Removing

Front door

- Pull off inner door seal from body flange. Installing

Page 39 / 44

Front door

- Align inner door seal with vulcanized point - arrow b - at the height of the lower hinge. - Start installation of inner door seal in upper radius - arrow a - of door opening. Outer door seal, removing and installing

Note: „

Removing and installing is described only for the right outer door seal. Removing and installing the left outer door seal is derived accordingly from this.

„

Remove protective foil only immediately prior to assembly. Processing temperature approx. 20 C.

„

Adhesive remover D 002 000 10 is to be used

Page 40 / 44

Front door

exclusively. „

The outer door seal must be applied immediately after cleaning.

„

After 10 minutes, check the seal for a secure fit.

Removing

- Pull off outer door seal from door. Installing

Page 41 / 44

Front door

- Remove any adhesive residue still present using radial disc for streak remover Z 432 290 TE - Thoroughly clean the adhesion surface with adhesive remover D 002 000 10 immediately before adhering the outer door seal. „

Adhesion surfaces must be free of dust and grease and there must be no residual adhesive present.

- Align outer door seal with cut-out arrow b - with door lock securing screw. - Vulcanized point - arrow c - of outer door seal is then located in center area of door entry sill. - Pull off foil cover and apply seal onto

Page 42 / 44

Front door

door. Do not stretch outer door seal excessively so that the seal is not too long at the end. - Press entire adhesive area of seal all around onto door using application roller 3356 , starting in upper radius - arrow a - of door. Note : „

Part numbers are for reference only. Always check with your Parts Department for the latest part number information

Checking seal for secure seating

Check seal for firm setting 10 minutes after adhering the seal. - Place seal - 1 - facing outward by

Page 43 / 44

Front door

hand. - If adhered area does not pull off in any areas, press seal on further once more using application roller 3356 .

Page 44 / 44