Volkswagen Golf V: Lock carrier

8 downloads 17886 Views 197KB Size Report
Service position 50-1,. Service position. ▫ Screw. ▫ Qty 4. ▫ 8 Nm. ▫ Screw. ▫ Qty. 8 ... Repair Manual, Body Collision Repair, Repair Group 00,. Technical data  ...
Volkswagen Golf V: Lock carrier

Page 1 / 6

50 - 1

Lock carrier Tools

Required special tools, workshop equipment, testing and measuring equipment, and aids „

Guide rod T 10093

„

Torque wrench 550 Nm V.A.G 1331

„

Torque wrench 40200 Nm V.A.G 1332

Lock carrier service position, assembly overview

Lock carrier

„

„

„

Page 2 / 6

Lock carrier with attachments „

Removing and installing 50-1, Lock carrier with attachments, removing and installing

„

Service position Service position

Screw „

Qty 4

„

8 Nm

Screw „

Qty. 8

„

60 Nm

50-1,

Lock carrier

Service position Performing service position

- Remove front bumper 63-1, Front bumper cover, removing and installing - Disengage hood release cable in coupling 55-1, Hood release cable, disconnecting - In vehicles with charge air cooler, disconnect pressure hoses 50-1, Releasing pressure hoses . - Remove signal horn - 4 - with bracket from longmember at right side

Page 3 / 6

Lock carrier

Repair Manual, Electrical Equipment, Repair Group 96, Lights, lamps, interior switch, signal horn, removing and installing - Unscrew bolts - 3 - at left and right longmembers. - Screw in guide rod T 10093 at left and right longmembers. - Remove bolts - 2 - at left and right on top of lock carrier - 1 - . - Lock carrier - 1 - can be pulled toward front approx. 10 cm on guide rod T 10093 . Resetting service position

Installation is performed in the reverse order of removal. - Center lock carrier on side rails and between fenders

Repair Manual, Body Collision Repair, Repair Group 00, Technical data; Body gap dimensions Note: „

Make sure that pressure hoses for charge air cooler are re-engaged correctly.

„

Hoses and lines must not be pinched.

Releasing pressure hoses

- Disengage connector coupling - 1 - and disconnect

Page 4 / 6

Lock carrier

pressure hose - 2 - in - direction of arrow - from coupling. - When re-connecting pressure hoses, make sure that connector couplings engage audibly. Lock carrier with attachments, removing and installing Removing

- Perform service position of lock carrier with attachments - 1 50-1, Performing service position . - Disconnect the electrical harness connectors present. - Drain coolant and disconnect coolant lines

Page 5 / 6

Lock carrier

Repair Manual, 2.0 Liter 4-Cyl. 4V Turbo Engine Mechanical, Fuel Injection Ignition, Engine Code(s): BPY, Repair Group 19, Cooling system parts; draining and filling coolant - Disconnect condenser lines

Repair Manual, Heating Air Conditioning, Repair Group 87, A/C system; removing and installing condenser - With a second technician, unscrew guide rod T 10093 on longmember on left and right sides and lift out lock carrier. Warning! If lines for A/C system and/or for coolant are disconnected, the powertrain aggregate must no longer be started. Note: „

Do not hang condenser and hydraulic oil cooler on hoses.

„

Lines for condenser and hydraulics must not be kinked.

Installing

Installation is performed in the reverse order of removal. „

Make sure that all plug and hose connections are corrected installed when re-assembling.

- Center lock carrier on side rails and between fenders

Repair Manual, Body Collision Repair, Repair Group 00, Technical data; Body gap dimensions

Page 6 / 6