MINI COOPER S (R 56) ... These installation instructions are primarily designed
for use within the MINI ... Support via the Aftersales Assistance Portal (ASAP).
Original MINI Accessories. Installation Instructions. USB/iPod Interface Retrofit MINI ONE and COOPER (R 56) MINI COOPER S (R 56)
These installation instructions are only valid for cars with SA 6NB (Wave radio). Retrofit kit No.
65 41 0 422 533
USB/iPod interface retrofit kit
Installation time The installation time is approx. 2.0 hours. This may vary depending on the condition of the car and the equipment in it. Important information These installation instructions are primarily designed for use within the MINI dealership organisation and by authorised BMW service companies. In any event the target group for these installation instructions is specialist personnel trained on MINI cars with the appropriate specialist knowledge. All work must be completed using the latest MINI repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. If you experience installation or function problems, limit troubleshooting to approx. 0.5 hours for mechanical or 1.0 hour for electrical work. In order to reduce costs and avoid any additional expense, send a query immediately to the Technical Parts Support via the Aftersales Assistance Portal (ASAP). Specify the following information: - Chassis number - Part number of the retrofit kit - A precise description of the problem - Work steps already carried out Do not archive the hard copy of these installation instructions since daily updates are made by ASAP! Pictograms Denotes instructions that draw your attention to special features.
Denotes the end of the instruction or other text.
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
1
Installation information All pictures show LHD cars; proceed accordingly on RHD cars. Ensure that the cables and/or lines are not kinked or damaged as you install them in the car. The costs thereby incurred will not be reimbursed by BMW AG. Additional cables/lines that you install must be secured with cable ties. If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used. Ordering instructions for cars with SA 493 (storage package) The iPod interface storage tray J is not included in the retrofit kit and must be ordered separately (part no. 65 15 0 428 922). Special tools required 00 9 317 Trim wedge
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
2
Contents Section
Page
1.
Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2.
Preparatory work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
3.
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4.
Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
5.
To install iPod and USB connection cable in cars without SA 493 (storage package) . . . . . . . . . . . . . .
8
6.
To install iPod and USB connection cable in cars with SA 493 (storage package) . . . . . . . . . . . . . . . . .
9
7.
To connect and install the cable kit and iPod interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8.
Concluding work and initialisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9.
Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
3
1.
Parts list
E
C
B
A
F
G
H
D
J
I
R56 0242 Z
Legend A
Cable kit
B
iPod connection cable
C
USB connection cable
D
iPod interface
E
USB holder
F
Black 4-pin socket casing
G
Black 3-pin socket casing
H
Grommet
I
Cable tie (10x)
J
iPod interface storage tray (not supplied with the retrofit kit)
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
4
2.
Preparatory work TIS No. ---
Conduct a brief test Disconnect negative pole of battery
61 20 900
The following components must be removed first of all Trim for the dashboard at the bottom
51 45 180
Trim for the centre console at the side
51 45 ...
Instrument cover
51 45 435
Centre console trim
51 16 160
Instrument cluster complete
62 10 125
Radio receiver
65 11 080
Additionally for cars with SA 493 (storage package) Oddments box (no longer required)
© BMW AG, Munich
51 45 ...
01 29 0 428 688
3/2007
(Z/Z)
5
3.
Connection diagram
A1 A2 A3 A4 A5 A6 A7
F
A
A8 A10 B
A9 B1
G
B2 C C2
C1 Branch/ Item
Designation
Signal
Cable colour / Cross-section
A
Cable kit
A1
Socket contact
AUX L
--SW
A2
Socket contact
AUX R
GE
R56 0243 Z
Connection location in the car
---
---
---
On radio receiver
X13813 PIN 2
On radio receiver
X13813 PIN 7
On radio receiver
X13813 PIN 8
0.35 mm2 0.35 mm2 A3
Socket contact
Shield
TR
Abbreviation / Slot
0.35 mm2 A4
Socket contact
CAN H
GN/OR
On radio receiver
X13812 PIN 11
A5
Socket contact
CAN L
GN
On radio receiver
X13812 PIN 9
A6
Socket contact
Tl. 30
RT/GN
On radio receiver
X13812 PIN 15
A7
Socket contact
Terminal 31
BR
On radio receiver
X13812 PIN 12
A8
Black 4-pin plug casing
A9
Black 3-pin plug casing
On socket casing G
---
A10
Black 12-pin socket casing
To iPod interface D
---
On socket casing F
---
B
iPod connection cable
---
---
B1
White 8-pin socket casing
---
---
To iPod interface D
---
B2
iPod connection plug
---
---
On iPod
---
C
USB connection cable
---
---
C1
USB connection (socket)
In USB holder
---
C2
USB connection (plug)
To iPod interface D
---
F
Black 4-pin socket casing
G
Black 3-pin socket casing
© BMW AG, Munich
---
---
---
---
---
---
With the disconnected cables of plug X13812 of the radio receiver
---
---
---
With the disconnected cables of plug X13813 of the radio receiver
---
01 29 0 428 688
3/2007
(Z/Z)
6
4.
Installation and cabling diagram
1 E* B
E C
D
2 A
R56 0244 Z
Legend A
Cable kit
B
iPod connection cable
C
USB connection cable
D
iPod interface
E
USB holder (for cars without SA 493 (storage package))
E*
USB holder (for cars with SA 493 (storage package))
1
iPod connection plug B2
2
Radio receiver, plugs X13812 and X13813
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
7
5.
To install iPod and USB connection cable in cars without SA 493 (storage package)
19
Drill a hole (1) in the glove compartment (2) using a 17 mm step drill bit according to the dimensions shown.
2
40
Drill a hole (3) in the glove compartment (2) using a 25 mm step drill bit according to the dimensions shown. 10
10
1 3
R56 0253 Z
Install iPod connection cable B as follows: - Route branch B1 through the hole
B1
1
- Push grommet H onto branch B1 and insert it into the glovebox (1)
H
- Route branch B1 to the vicinity of the radio receiver
R56 0208 Z
Insert branch C1 (socket) of USB connection cable C into USB holder E.
C1
E
R56 0205 Z
Install USB holder E as follows:
C2
- Route branch C2 through the hole
2
- Insert USB holder E in the glovebox (1) and screw on from behind using a retaining nut (2)
1
- Route branch C2 to the vicinity of the radio receiver
E
R56 0246 Z
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
8
6.
To install iPod and USB connection cable in cars with SA 493 (storage package) Insert branch C1 (socket) of USB connection cable C into USB holder E.
C1
E
R56 0205 Z
Drill a hole (1) in iPod interface storage tray J using a 25 mm step drill bit according to the dimensions shown.
J
30 mm
1
R56 0206 Z
Install USB holder E as follows: - Route branch C2 through the hole
J
1
- Insert USB holder E into iPod interface storage tray J and screw on from behind using a retaining nut (1).
C2
E
R56 0207 Z
145 mm 37 mm
Mark the holes (1) according to the dimensions shown on the CD changer/oddments box holder (2) and drill through with a 5 mm twist drill bit.
1 2 12 mm R56 0211 Z
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
9
6. To install iPod and USB connection cable in cars without SA 493 (storage package)
J
2
C2 1
Remove screws (3) from iPod interface storage tray J (no longer required). Guide branch B1 through the opening in iPod interface storage tray J and fold lid (2) over. Thread branches B1 and C2 through the opening in the CD changer/oddments box holder (1).
3
Insert iPod interface storage tray J in the CD changer/ oddments box holder (1).
B1
R56 0248 Z
Attach CD changer/oddments box holder (1) to iPod interface storage tray J using screws (2) previously removed.
2 1 J R56 0249 Z
B2
J
0 11
Pull branch B2 out of iPod interface storage tray J as far as dimension shown.
m
m
R56 0250 Z
Route branches B1 and C2 to the vicinity of the radio receiver.
B1 C2 R56 0251 Z
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
10
7.
To connect and install the cable kit and iPod interface
F
Disconnect the following cables from plug X13812 (black 16-pin) of the radio receiver and connect to socket casing G:
A8
- Brown cable from PIN 12 to socket casing F PIN 1 - Red/green cable from PIN 15 to socket casing F PIN 2
X13812
- Green cable from PIN 9 to socket casing F PIN 3
A6
A4
A7 A5
R56 0182 Z
- Green/orange cable from PIN 11 to socket casing F PIN 4 Connect branches A4 - A7 as follows to plug X13812: - Branch A4, green/orange cable, to PIN 11 - Branch A5, green cable, to PIN 9 - Branch A6, red/green cable, to PIN 15 - Branch A7, brown cable, to PIN 12 Connect branch A8 to socket casing F. Disconnect the following cables from plug X13813 (black 12-pin) of the radio receiver and connect to socket casing G:
G
A9
- Yellow cable from PIN 7 to socket casing G PIN 1 - Black cable from PIN 2 to socket casing G PIN 3 - Transparent cable from PIN 8 to socket casing G PIN 2 If the cable colours in the car do not match, the pin assignment must be observed.
A1-A3
Connect branches A1 - A3 to plug X13813 as follows:
X13813
R56 0186 Z
- Branch A1, black cable, to PIN 2 - Branch A2, yellow cable, to PIN 7 - Branch A3, transparent cable, to PIN 8 Connect branch A9 to socket casing G.
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
11
7. To connect and install the cable kit and iPod interface Connect branches A10, B1 and C2 to iPod interface D.
A10
D B1 C2 R56 0169 Z
Secure iPod interface D to the support (1) using two cable ties I from underneath.
D 1 I R56 0252 Z
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
12
8.
Concluding work and initialisation
This retrofit system does not require coding. - Connect the battery - Conduct a brief test - Initialise the iPod as follows 1. Disconnect the iPod if it is connected 2. Switch on the ignition 3. Switch on the radio 4. Change to AUX mode 5. Press and hold station button 2 until MINI appears on the radio display 6. Switch off the ignition - Conduct a function test - Re-assemble the car
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
13
3/2007 VB CAN_H
X10953
(Z/Z)
14
11
A4*
0,35 GN/OR
VB CAN_L
0,35 GN
CAN_H
CAN_L
A5*
8
9
0,35 GN/OR
CAN_H
X10952
0,35 GN
CAN_L
7
0,75 RT/GN
01 29 0 428 688
R56 0185 Z 30
© BMW AG, Munich
N9 VB 30
X3206
15
A6*
30
VB 31
X1091
0,5 RT/GN
1
31
0,75 BR
12
A7*
31
2
0,5 BR
X13812 D*
3
3
4
4 2
2
1
1
0,75 BR
31
0,75 RT/GN
30
0,35 GN
CAN_L
0,35 GE/GN
CAN_H
A8* F* 1
1
3
3
2
2
AUX IN L
0,35 GE
AUX IN R
11
3
0,35 SW
Schirm
0,35 TR
4
0,35 SW
0,35 TR
A9* G*
AUX_NF_R
N9
AUX_NF_L 5
2
A1*
A2*
7
0,35 GE
6
0,35 SW
8
A10 *
X13813*
A3*
Schirm
12
0,35 TR
7.
Circuit diagram
7. Circuit diagram Legend A1*
Socket contact
A2*
Socket contact
A3*
Socket contact
A4*
Socket contact
A5*
Socket contact
A6*
Socket contact
A7*
Socket contact
A8*
Black 4-pin plug casing
A9*
Black 3-pin plug casing
D*
iPod interface
E*
USB-AUX in jack
F*
Black 4-pin socket casing
N9*
Radio receiver
X1091*
Terminal 31 connector
X3206*
Terminal 30 connector
X10952
CAN L connector
X10953
CAN H connector
X13812
16-pin radio plug
X13813
Black 12-pin socket casing
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours BR
Brown
SW
Black
GN
Green
TR
Transparent
RT
Red
WS
White
© BMW AG, Munich
01 29 0 428 688
3/2007
(Z/Z)
15
