WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES. 1994 Toyota Celica.
1994 WHEEL ALIGNMENT. Toyota - Specifications & Procedures. Celica.
After tran-axial repair on front wheel drive cars. Q. How often should I ... Q. What
is the difference between Tracking and Four Wheel Alignment? A. Tracking is an
...
regional specification data base to be used in the alignment process. ... 4 - Wheel
Split Positioning - Use when the alignment rack is too short for full roll back ...
Two wheel alignment is quickly becoming obsolete and four ... Specific
procedures must be followed to ... for positive caster specifications or 1/2 degree
more for.
Similarly, if the wheel alignment of a vehicle is out of order, the rubbing of tyres
will be more and free movement ... data is entered by potential meters and.
Title: Toyota Sienna Wheel Torque Specs Keywords: Toyota Sienna Wheel Torque Specs Created Date: 11/3/2014 7:39:42 PM
Title: Dodge Ram Front Wheel Bearing Torque Specs Keywords: Dodge Ram Front Wheel Bearing Torque Specs Created Date: 9/5/2014 12:34:00 PM
Suspension type can be obtained from the vehicle data stick- er spare wheel
recess or in the glovebox owner's manual. Table b. Wheel Alignment Data—Front
...
offered in a Camaro, including the original ZL1 engine from 1969. The latest .....
warning lamp and the ABS warning lamp may ... 2007-2008 Chevrolet Impala,
Malibu,. Uplander; Pontiac G6, Montana SV6;. Saturn AURA, VUE; with the 3.5L
V6.
1963-73 MG SPECIFICATIONS & ADJUSTMENTS. TIRE ... Before attempting to
check or adiust wheel alignment, ensure ... procedure and check camber.
Wheel Alignment specifications as an “Actual value with a plus or minus
tolerance”. For example TOE IN = Target data is +2mm +/-. 1mm This means that
the ...
wheels up to 19 1/2". • Level Compensator ... Data Recorder Software. • Wheel
Clamp ... Align where you are! Toll free: 1-800-496-3777. Fax: 360-371-0553.
Steering wheel clamp. 1. Power cord. 1. Alignment data chart. 2. Turn plates. 2.
Base plates. 1. Operators manual. 1. Rim button extension kit 50mm. 1.
Today's wheel alignment inspection systems adopt various computer-vision technologies. ... It involves measuring the geometric alignment among the four wheels of a vehicle ... Camber is defined as an angle forming the centerline of a wheel.
Note: All specs are for both two-wheel drive (4x2) and four-wheel drive (4x4)
unless otherwise noted. 2011 4Runner Product Information. MATRIX.
their vehicle using one of the set ups indicated below. Use factory caster tool to achieve recommended caster settings â
Domestic car Alignment specs 57 - 72 Author: bq1555 Created Date: 12/9/2010 8:58:56 AM ...
TSIO-520 G. TSIO-520 H. TSIO-520 M. TSIO-520 P. TSIO-520 R. LTSIO-520 AE.
0-470 R. O-470 K. O-470 L. O-470 S. O-470 U. IO-470 F. IO-470 N. IO-550 D.
ISO 8434-2. U.S.S.R. Register of Shipping cert. #93.017.260. SAE J514. MIL-F-
18866 MS Sheets. MS51811 - MS51843*. U.S. Coast Guard - meet applicable.
Prior to performing wheel alignment, perform preliminary visual and mechanical inspection of wheels, tires and suspension components. See PRE-ALIGNMENT INSTRUCTIONS in WHEEL ALIGNMENT THEORY/OPERATION article in the GENERAL INFORMATION section.
WHEEL ALIGNMENT PROCEDURES CAMBER ADJUSTMENT 1) Camber angle can be adjusted by altering the fixing bolt hole position for the upper spring strut mount. Remove front nut in spring strut upper retaining plate. Using a soft-faced hammer, remove front press bolt. 2) Loosen rear bolt on retaining plate. Set Wrench (5038) on rear bolt and turn suspension assembly so hole in retaining plate passes hole in suspension tower at least .12" (3 mm). See Fig. 1. Mark position when hole can no longer be seen and turn wrench an additional .12" (3 mm).
Fig. 1: Turning Front Suspension Assembly (960) Courtesy of Volvo Cars of North America. 3) Mark position of new hole with a punch. Tighten rear nut to 35 ft. lbs. (48 N.m) so strut will not move out of position.
4) Drill a new hole in retaining plate, through hole in top of suspension tower. Use care not to damage hole in suspension tower. Install and tighten front press bolt and nut. Tighten bolt in retaining plate. Remove front press bolt and replace with new bolt, nut and lock washer. Tighten bolt to 35 ft. lbs. (48 N.m).
CASTER ADJUSTMENT Caster angle can be adjusted by replacing the control arm strut. A shorter strut reduces caster angle by .8 degrees. A longer strut increases caster angle by .8 degree.
TOE-IN ADJUSTMENT To adjust toe-in, lengthen or shorten tie-rod ends as necessary.
TROUBLE SHOOTING Refer to TROUBLE SHOOTING - BASIC PROCEDURES article in the GENERAL TROUBLE SHOOTING section.
Camber (1) Front .................. .3 .............. -0.2 To 0.8 Caster (1) ............... 5 ............... 4.5 To 5.5 Toe-In (2) Front ............... .18 (4.5) .. .13 To .23 (3 To 6) Toe-In (1) Front .................. .37 .............. .27 To .47 (1) - Measurement is in degrees. (2) - Measurement is in inches (mm).
