Auto Day Night Mirror

Accessory

INSTALLATION INSTRUCTIONS

Application

AUTOMATIC DAY/NIGHT MIRROR

PARTS LIST Automatic Day/Night Mirror Kit P/N 08V03-S9A-100B Day/Night mirror

Owner’s Manual

Publications No.

AII 27335-27953 2005 ODYSSEY

Issue Date

OCT 2004

TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver 8 mm Socket Ratchet Tape measure T20 Torx bit Isopropyl alcohol Shop towel Clip remover Illustration of the Day/Night Mirror Installed on the vehicle

Automatic Day/Night Mirror Attachment Kit P/N 08V03-SJA-101 MAIN HARNESS

DAY/NIGHT MIRROR

Wire cover

Mirror harness

Subharness

4321081Y

9 Wire ties

4 EPT seals

5 Cushion tapes

Ground bolt

© 2004 American Honda Motor Co., Inc - All Rights Reserved.

INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.

Make sure you have the anti-theft code for the radio, then write down the radio station presets.

2.

Disconnect the negative cable from the battery.

AII 27335-27953 (0410)

08V03-SHJ-1000-91

1 of 8

3.

Remove the mirror by lifting it up out of the mirror base.

7.

Remove the two retaining tabs and remove the cover from the left sunvisor.

SUNVISOR HOLDERS

MIRROR BASE

VEHICLE CONNECTOR COVER

ROOM MIRROR

RETAINING TAB

LEFT SUNVISOR

4321010Y

4. 5.

Remove the right and left map light lens (four tabs for each lens).

PHILLIPS SCREW

Remove the two 5 mm bolts, ground bolts and pull out the room light.

4301191B

8.

Remove the two phillips screws, pull out the left sun visor, disconnect the vehicle connector, and remove the sunvisor.

9.

Repeat steps 7 and 8 to remove the right sunvisor.

10. Remove the right and left sunvisor holders. 11. Remove the door opening trim from around the left front “A” pillar trim. Remove the left front “A” pillar (two clips).

VEHICLE CONNECTOR

ROOF CONSOLE RETAINING TABS (4) CLIP RETAINING TABS (4) DOOR OPENING TRIM

RIGHT MAP LIGHT LENS GROUND BOLTS (2)

LEFT MAP LIGHT LENS

6.

2 of 8

5 mm BOLTS (2)

LEFT FRONT “A” PILLAR TRIM CLIP

4301182B

Disconnect the two vehicle connectors and remove the room light case. LX model has only one connector.

4310011B

12. Remove the right front “A” pillar the same way.

AII 27335-27953 (0410)


13. Remove the left front door sill trim (three clips).

LEFT FRONT DOOR SILL TRIM

17. Remove the damper arm cover and disconnect the arm. GLOVE BOX

CLIPS (3)

DAMPER ARM

4301210B

COVER

14. Remove the right front door sill trim (three clips).

4324021B

15. Pull out the door opening trim at the left kick panel. Remove the left kick panel (three clips).

GLOVE BOX

18. Open the glove box. Remove the two stoppers by releasing the two retaining tabs for each stopper. Remove the glove box (two screws). Remove cover and rod.

CLIPS (3)

DOOR OPENING TRIM

GLOVE BOX

LEFT KICK PANEL

4301221B

16. Remove the right kick panel the same way. SCREWS (2) STOPPERS (2) RETAINING TAB


AII 27335-27953 (0410)

4219040B

3 of 8

19. Get the automatic day/night mirror, and the subharness. Plug the 7-pin connector from the subharness into the mirror.

Routing the Mirror Harness 23. Get the mirror harness, plug the subharness connector into the mirror harness connector. Be careful not to plug in the subharness into the roof console connector.

20. Install the mirror to the mirror base. TORX SCREW

CONSOLE OPENING

SUBHARNESS CONNECTOR MIRROR BASE


MIRROR HARNESS CONNECTOR

SUBHARNESS 7-PIN CONNECTOR

ROOM MIRROR

4321020Y

4321040Y

21. Secure the automatic day/night mirror to the mirror base by tightening the torx screw. 22. Route the subharness up to the headliner and pull it out through the console opening.

24. Attach the mirror harness connector to the vehicle panel with one EPT sealer as far forward as possible. MIRROR HARNESS CONNECTOR

CONSOLE OPENING

VEHICLE PANEL

HEADLINER SUBHARNESS CONNECTOR SUBHARNESS

4321030Y


EPT SEAL

AUTOMATIC DAY/NIGHT MIRROR 4321050Y

4 of 8

AII 27335-27953 (0410)


25. Route the terminal from the mirror harness under the headliner toward the right side of the vehicle.

28. Secure the mirror harness to the vehicle harness using three wire ties.

CONSOLE OPENING

MIRROR HARNESS

HEAD LINER

RIGHT FRONT “A” PILLAR GLOVE BOX VEHICLE HARNESS OPENING

WIRE TIE 4321210Y

4321060Y

DASHBOARD

MIRROR HARNESS TERMINAL

26. Continue routing the mirror harness down the “A” pillar and behind the dashboard.

29. Using isopropyl alcohol on a shop towel, clean the right front “A” pillar area where the mirror harness will attach. Attach the mirror harness to the right front pillar using four cushion tapes.

27. Locate the 22-pin connector below the dashboard at the kick panel area. Disconnect the vehicle 22-pin connector, unlock the connector terminal pin lock, and insert the mirror harness terminal into the vehicle 22-pin connector at the location shown. Reconnect the 22-pin connector.

RIGHT FRONT “A” PILLAR CUSHION TAPE

SRS Do not attach to the SRS mount.

MIRROR HARNESS TERMINAL

MIRROR HARNESS TERMINAL SIDE 4321221Y

VEHICLE 22-PIN CONNECTOR

(View from the harness side)


4321202Y

AII 27335-27953 (0410)

5 of 8

30. Using isopropyl alcohol on a shop towel, clean the headliner area where the mirror harness will attach. Using scissors, cut two EPT sealers in half. Using three halves of EPT sealers, attach the mirror harness to the vehicle panel.

32. Plug the mirror harness 6-pin connector into the 6-pin opening in the fuse box.

MIRROR HARNESS EPT SEAL (cut in half.)

MIRROR HARNESS 6-PIN CONNECTOR

VEHICLE PANEL

EPT SEAL

MIRROR HARNESS HEAD LINER

FUSE BOX

31. Route the ground terminal end from the mirror 4321071Y harness along the headliner and down the left front “A” pillar towards the left fuse box. CONSOLE OPENING

4321020B

FUSE BOX 6-PIN OPENING

NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the 6-pin connector taped to the day/night harness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the day/night harness you just unplugged and plug the day/night harness into the fuse box. FUSE BOX DAY/NIGHT HARNESS 6-PIN CONNECTOR

MIRROR HARNESS GROUND

DUMMY CONNECTOR

OTHER ACCESSORY 6-PIN CONNECTOR

LEFT FRONT “A” PILLAR

4319060B

4321010B

DRIVER’S SIDE

6 of 8

AII 27335-27953 (0410)


33. Remove the bolt from the fuel lid opener. Attach the ground terminal from the mirror harness, and reinstall the fuel lid opener using the ground bolt supplied.

35. Using isopropyl alcohol on a shop towel, clean the vehicle panel. Attach the mirror harness to the vehicle panel using one cushion tape. 36. Along the left front “A” pillar area, secure the mirror harness to the vehicle harness using four wire ties. MIRROR HARNESS

GROUND BOLT

WIRE TIE LEFT FRONT “A” PILLAR

FUSE BOX

FUEL LID OPENER

VEHICLE HARNESS

VEHICLE BOLT (Discard.) MIRROR HARNESS GROUND TERMINAL HOOD OPENER

4321060B

4321040B

34. Secure the mirror harness to the vehicle harness using two wire ties. CUSHION TAPE

37. Using scissors, cut one EPT sealer in half, using isopropyl alcohol on a shop towel, clean the headliner area. Secure the mirror harness to the headliner using three pieces of EPT sealer (one piece was cut in step 30).

VEHICLE HARNESS Half the EPT sealer from step 29.

EPT SEALER

VEHICLE PANEL MIRROR HARNESS

CONSOLE OPENING

HEAD LINER

WIRE TIE

4321050B


AII 27335-27953 (0410)

4321070B

7 of 8

38. Install the wire cover from the mirror to the headliner. CONSOLE OPENING

SUBHARNESS

MIRROR WIRE COVER

4321080B

39. Reinstall all removed parts. 40. Reconnect the negative cable to the battery. 41. Enter the customer’s radio anti-theft code, and reset the radio station presets. 42. Reset the clock. 43. If equipped check the operation of the satellite radio according to the vehicle’s Owner’s Manual. NOTE: Whenever the battery is disconnected, the driver’s AUTO function is disabled. 44. Start the engine. Push down on the driver’s window switch until the window is fully open. 45. Pull up on the driver’s window switch to close the window completely, then hold the switch for 2 seconds or more. 46. Test the AUTO window function.

8 of 8

AII 27335-27953 (0410)
