Cisco IPsec Configuration Guide Peplink ... - Cloud Distribution
Recommend Documents
http://www.cisco.com/en/US/docs/ios-xml/ios/iproute_lisp/configuration/15-1mt/irl-15-1mt-book.html. In the meantime, ple
configuration on a Cisco router configured for IPsec VPN, per. baseline (i.e. configuration compliance checking). This. enabled rapid security assessment using ...
such as a router, while the LAC can be a dial-up Network Access Server (NAS) ... over a public IP network without a gate
Document Information. Document Title: Cisco 1700 Series Router Software
Configuration Guide. Part Number: 78-5407-03. On a scale of 1–5 (5 being the
best), ...
The Cisco Video Surveillance IP Camera offers a feature-rich digital camera
solution for a video surveillance system. The camera provides high-definition (HD
) ...
Catalyst 3750G Integrated Wireless LAN Controller Switch 11 ..... Full control of
up to 16 wireless LAN (SSID) policies for Cisco 1000 series access points. Note.
Installing and Setting Up Cisco CP Express Admin View 2-1 ..... ://www.cisco.com/
cisco/software/release.html?mdfid=281795035&flowid=5160&softwareid=2821
.... By default, the HTTP and secure server are enabled for factory fresh routers.
Any use of actual IP addresses in illustrative content is unintentional and
coincidental. Cisco IOS Multiprotocol Label Switching Configuration Guide.
maintenance tasks, the relationship among tasks, or the Cisco IOS commands
necessary to perform particular tasks. The Cisco IOS documentation set is also ...
iii. Cisco IOS XR MPLS Configuration Guide. Preface vii. Document Revision
History for Release 3.2 vii. Obtaining Documentation viii. Cisco.com viii.
Cisco IOS, the Cisco IOS logo, Cisco Systems, Cisco Systems Capital, the Cisco
Systems logo, .... MPLS Commands and Saved Configurations XC-81.
Is the carrier detect (CD) light on the front panel of the Cisco DSL Router on or off
?....................6 ..... Cisco DSL Router Configuration and Troubleshooting Guide.
Configuration Examples for Basic SIP Configuration 54. SIP Register Support ...
Loose-Routing and the Record-Route Header 89. Multiple INVITE Requests ...
Catalyst 3750G Integrated Wireless LAN Controller Switch 1-14. Cisco UWN
Solution ... Enabling Wireless Connections to the GUI and CLI 2-36. CHAPTER. 3
.
Mar 31, 2015 ... Setting a Default Route in the Management Ethernet Interface VRF 36 .... such as
No Service Password Recovery, Multilink PPP Support, and ...
Start Here Cisco IOS Software Release Specifics for IPv6 Features 1. Finding
Feature ... Cisco IOS IPv6 Features and Supported Software Releases 2.
packet. A digital signature (=hash) is computed over the entire packet, with the exception of the mutable fields (fields
between Cisco and any other company. (0201R). Software Configuration Guide
for the Cisco 2600 series, Cisco 3600 Series, and Cisco 3700 Series Routers.
Prerequisites for Basic H.323 Setup and Management 20 ..... T6, is not
configurable and has a default of 120 seconds if the ISUP variant Q.761 is used.
UPnP⢠is a certification mark of the UPnP⢠Implementers Corporation. > ... Apple® and Mac OS® are registered tr
IPsec VPN Guide. Opengear to Shrew Soft VPN Client. This is a guide on how to
create an IPsec VPN tunnel from a local client running. Shrew Soft VPN Client ...
Cisco IPsec Configuration Guide Peplink ... - Cloud Distribution
CISCO IPSEC CONFIGURATION GUIDE Peplink Balance Series
1
Configure IPsec (Main Mode) between Peplink and Cisco
IPsec configuration on Cisco !--- Configure an ISAKMP policy !--- It is belongs to Phase 1 negotiations crypto isakmp policy 10 encr 3des authentication pre-share group 2
!--- Specifies the preshared key "abc123" for Peplink’s WAN1 and WAN2 crypto isakmp key abc123 address 210.9.66.68 crypto isakmp key abc123 address 60.2.2.2
!--- Configure IPsec policies and specify the transform sets !--- It is belongs to Phase 2 negotiations crypto ipsec transform-set 3desset esp-3des esp-sha-hmac
!--- Creates crypto map for IKE establish the IPsec SA !--- It is belongs to Phase 2 negotiations crypto map peplink_map 10 ipsec-isakmp
!--- Sets the IP addresses of the remote Peplink !--- You have to enter the outgoing public IP if Peplink is behind NAT set peer 210.9.66.68 set peer 60.2.2.2
CISCO IPSEC CONFIGURATION GUIDE Peplink Balance Series
!--- Specifies IPsec to use the transform-set “3desset” that configured above set transform-set 3desset !--- Specifies the traffic to be encrypted. match address 100
!--- External Side interface FastEthernet0/0 ip address 90.99.66.99 255.255.255.0 duplex auto speed auto crypto map peplink_map
!--- Internal Side interface FastEthernet0/1 ip address 192.168.227.1 255.255.255.0 duplex auto speed auto ! ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 90.99.66.1 ! ! !--- Define access list for IPsec traffic from subnet !--- 192.168.227.0/24 to 192.168.226.0/24 access-list 100 permit ip 192.168.227.0 0.0.0.255 192.168.226.0 0.0.0.255
CISCO IPSEC CONFIGURATION GUIDE Peplink Balance Series
2
Configure IPsec (Aggressive Mode) between Peplink and Cisco
IPsec configuration on Cisco !--- Define Keyring, pre-shared key with hostname crypto keyring dynkey pre-shared-key hostname vpn@peplink key secret_password
!--- Create an ISAKMP policy for Phase 1 negotiation !--- with 3DES, SHA1, DH Group 2 crypto isakmp policy 10 encr 3des authentication pre-share group 2 !--- Define ISAKMP Profile and include Keyring “dynkey” to this profile !--- Cisco U-FQDN is vpn@cisco !--- Peplink U-FQDN is vpn@peplink crypto isakmp profile dynprofile keyring dynkey self-identity user-fqdn vpn@cisco match identity user vpn@peplink initiate mode aggressive
!--- Part of IPsec phase 2 negotiation !--- Define IPsec transform-set with ESP, 3DES, HMAC_SHA crypto ipsec transform-set 3desset esp-3des esp-sha-hmac
CISCO IPSEC CONFIGURATION GUIDE Peplink Balance Series !--- Add the Transform-set and ISAKMP profile which defined above to this !--- crypto dyanmaic map. !--- Set the PFS Group 2 and include the access list. crypto dynamic-map dynmap 10 set transform-set 3desset set pfs group2 set isakmp-profile dynprofile match address 100
!--- Add the dynamic map into crypto map crypto map crymap 10 ipsec-isakmp dynamic dynmap !--- External side. interface FastEthernet0/0 ip address 90.99.66.99 255.255.255.0 duplex auto speed auto
!--- Apply crypto map to the interface crypto map crymap
!--- Internal side. interface FastEthernet0/1 ip address 192.168.227.1 255.255.255.0 duplex auto speed auto ip route 0.0.0.0 0.0.0.0 90.99.66.1
!--- Define access list for IPsec traffic from subnet !--- 192.168.227.0/24 to 192.168.226.0/24 access-list 100 permit ip 192.168.227.0 0.0.0.255 192.168.226.0 0.0.0.255
