See discussions, stats, and author profiles for this publication at: https://www.researchgate.net/publication/225717122
Effect of temperature on soil-water characteristics and hysteresis of compacted Gaomiaozi bentonite Article in Journal of Central South University of Technology · October 2009 DOI: 10.1007/s11771-009-0136-x
CITATIONS
READS
33
175
6 authors, including: WM Ye
Bao Chen
Tongji University
Tongji University
146 PUBLICATIONS 1,307 CITATIONS
39 PUBLICATIONS 411 CITATIONS
SEE PROFILE
SEE PROFILE
Yonggui Chen Tongji University 82 PUBLICATIONS 748 CITATIONS SEE PROFILE
Some of the authors of this publication are also working on these related projects:
hydraulic and mechanical properties of bentonite-based materials View project
Activity excitation of steel slag-metakaolin composite geopolymer and macro-micro behavior of stabilized soft clays View project
All content following this page was uploaded by WM Ye on 01 June 2014. The user has requested enhancement of the downloaded file.
J. Cent. South Univ. Technol. (2009) 16: 0821−0826 DOI: 10.1007/s11771−009−0136−x
Effect of temperature on soil-water characteristics and hysteresis of compacted Gaomiaozi bentonite YE Wei-min(叶为民)1, 2, WAN Min(万 敏)1, CHEN Bao(陈 宝)1, CHEN Yong-gui(陈永贵)1, CUI Yu-jun(崔玉军)3, WANG Ju(王 驹)4 (1. Key Laboratory of Geotechnical and Underground Engineering, Ministry of Education, Tongji University, Shanghai 200092, China; 2. United Research Center for Urban Environment and Sustainable Development, Ministry of Education, Shanghai 200092, China; 3. Ecole des Ponts Paries Tech, Paris, France; 4. Beijing Research Institute of Uranium Geology, Beijing 100029, China) Abstract: Laboratory tests under different constraint conditions were carried out to obtain the soil-water retention curves (SWRCs) of highly-compacted confined/unconfined Gaomiaozi (GMZ) bentonite at 20, 40 and 80 ℃, respectively. The effect of temperature on the soil-water characteristics of the highly-compacted GMZ bentonite was analyzed. The results show that the water retention capacity of the highly-compacted GMZ bentonite decreases as the temperature increases under unconfined and confined conditions. At a certain temperature, the constraint conditions have little influence on the water retention capacity of the compacted bentonite at high suction, but the water retention capacity of the confined specimen is lower than that of the unconfined specimen at low suction. Under unconfined conditions, the hysteretic behaviour of the compacted bentonite decreases with increasing temperature. At high suction (>4 MPa), the hysteretic behaviour of the unconfined bentonite tends to increase with the decrease of the suction. In summary, the hysteretic behaviour of the compacted bentonite is not significant. Key words: Gaomiaoz; bentonite; soil-water characteristic; hysteretic behavior; nuclear waste repository; water retention capacity; temperature
1 Introduction In the design concept of multi-barrier system of deep geological disposal for high-level radioactive waste, the highly-compacted bentonite has been widely used for construction of artificial barrier. Because of the radiogenic heat released from the waste container, the infiltration groundwater from the surrounding rock and the mechanical stress induced by the hygroscopic expansion of the working compacted bentonite, the highly-compacted bentonite experiences coupling of thermo-hydro-mechanical process. In order to ensure the safety and effective operation of high-level radioactive waste repository, it is important to investigate the effect of temperature on hydro-mechanical characteristics of the compacted bentonite used as buffer materials [1]. Soil-water characteristic is one of the key indexes of
hydro-mechanical property of bentonite. Many studies were conducted on the effect of temperature on soil-water characteristics of the highly-compacted bentonite [2−5]. ROMERO et al [6], and VILLAR and LLORET [7] experimentally obtained soil-water retention curves of the compacted BOOM clay and FEBEX bentonite by different temperature experiments, respectively. JACINTO et al [8] measured the retention curves of different dry densities of MX−80 bentonite following the wetting path at different temperatures, and modified the van Genuchten’s model by considering the effect of temperature on the water retention capacity. But the above studies only concerned about the effect of temperature on the soil-water characteristics following single drying/wetting path. In fact, under the influence of gas generation and groundwater infiltration of radioactive waste disposal, the compacted bentonite has a soil-water hysteresis caused by the multi-drying/
Foundation item: Projects(40772180, 40572161, 40802064) supported by the National Natural Science Foundation of China; Project ([2007]831) supported by Commission of Science, Technology and Industry for National Defense of China; Project(07JJ4012) supported by Hunan Provincial Natural Science Foundation of China; Project(20080430680) supported by China Postdoctoral Science Foundation; Project(08R214155) supported by Shanghai Postdoctoral Scientific Program of China; Project(B308) supported by Shanghai Leading Academic Discipline Project of China Received date: 2008−12−26; Accepted date: 2009−03−24 Corresponding author: YE Wei-min, PhD, Professor; Tel: +86−21−65985086; E-mail:
[email protected]
822
wetting circles in a certain range of suction [9−10]. The studies on the soil-water hysteresis were focused on developing thermo-dynamic models of hysteresis for soil-water characteristic curves, such as the bounding surface model [11−12], and the internal-variable model [13]. Based on the internal-variable theory of capillary hysteresis, XU et al [14] developed a mathematical model to describe the soil-water characteristics of geotechnical media experiencing arbitrary drying-wetting paths. The effect of air entrapment was fully taken into account in XU’s model. Gaomiaozi (GMZ) bentonite was selected as buffer materials of Chinese geological repository for high level radioactive nuclear waste [15]. CHEN et al [16] studied the soil-water characteristic curves of highly-compacted bentonite using the osmotic technique and vapor equilibrium technique to control suction. YE et al [17] studied the swelling pressure characteristics of the GMZ bentonite by the constant volume test, and found that there was an exponential relationship between the swelling pressure and the dry density. QIN et al [18] analyzed the effects of the dry density, the vertical stress and the soaking liquid on the swelling characteristics of the GMZ bentonite. The objective of the present study is to investigate the temperature effect on the soil-water characteristics and hysteretic behaviors of highlycompacted GMZ bentonite under unconfined and confined conditions.
J. Cent. South Univ. Technol. (2009) 16: 0821−0826 Table 1 Properties of GMZ bentonite Property
Description
Specific gravity of soil grain
2.66
pH
8.68−9.86
Liquid limit/%
276
Plastic limit/%
37
Total specific surface area/ (m2·g−1)
570
Cation exchange capacity/ (mmol·g−1)
0.773 0
Main exchanged cation/ (mmol·g−1)
Na+(0.433 6), Ca2+(0.291 4), Mg2+(0.123 3), K+(0.025 1)
Main minerals
montmorillonite(75.4%), quartz (11.7%), feldspar (4.3%), cristobalite (7.3%)
Table 2 Initial state parameters of specimen Parameter
Value
Height/mm
6
Diameter/mm
20
Water content/% −3
Dry density/(g·cm )
10.65 1.7
2 Experimental 2.1 Materials The properties of GMZ bentonite used in the experiment are shown in Table 1, indicating that GMZ bentonite has high cation exchange capacity, great adsorption ability, good dispersion and good hydraulic properties. The GMZ bentonite powder was compacted into a thin cylindrical specimen. A digital frame was employed for the compaction. The compaction was digitally controlled at a vertical velocity of 0.1 mm/min to ensure the specimen uniformity. Even so, it is difficult to achieve the optimum homogenization [19]. The initial state parameters of the specimen are listed in Table 2. 2.2 Apparatus The compaction devices are shown in Fig.1, including a steel mould and a piston. The bentonite powder can be compressed into a thin cylindrical specimen in the steel mould under the universal press. Self-designed cells with small holes in two ends are
Fig.1 Photo of compaction mould
shown in Fig.2, which were employed for suction control test under confined conditions. The holes were designed as channels for moisture exchanges between specimen in the cell and the circulating air around it. For the test under unconfined conditions, the specimen was placed inside an aluminous container as shown in Fig.2. The apparatus using vapour phase technique suggested by YE et al [20], as shown in Fig.3, was placed in the desiccator, and the salt solution was used
Fig.2 Photos of specimen of compacted bentonite: (a) Unconfined specimen; (b) Confined specimen in self-designed cell
J. Cent. South Univ. Technol. (2009) 16: 0821−0826
823
In order to obtain the temperature effect on the soil-water characteristics of highly-compacted GMZ bentonite, soil-water retention (SWR) tests of GMZ bentonite following drying/wetting cycles were carried out under both unconfined and confined conditions at 20, 40 and 80 ℃ respectively, and soil water retention curves (SWRCs) and hysteretic circles were obtained correspondingly.
3 Results and discussion
Fig.3 Setup of vapour phase technique
for suction control. The air pump was used to keep air in circulation. The whole system was placed in a digital oven for temperature control with the resolution of (±0.1) ℃. 2.3 Methods and test procedure 2.3.1 Temperature control In order to investigate temperature effects on soil-water characteristics of the compacted GMZ bentonite, 20, 40 and 80 ℃ were selected for temperature control in the tests. 2.3.2 Suction control The vapour equilibrium method was employed to control the suction. Different saturated salt solutions were used to control the relative humidity of the circulating air in the whole system. Their corresponding imposed suctions at 20, 40 and 80 ℃ are shown in Table 3. The high suctions (>4 MPa) were calibrated by TANG and CUI [21] and the low suctions were controlled by unsaturated NaCl solutions suggested by LYTTON [22]. Table 3 Corresponding suction of salt solution at different temperatures (unit: MPa) Salt solution
20 ℃
40 ℃
80 ℃
LiCl2
309.0
−
−
MgCl2
150.0
162.4
219.5
K2CO3
113.0
122.0
167.4
Mg(NO3)2
82.0
103.1
−
NaNO2
57.0
−
−
NaNO3
39.0
49.5
69.0
NaCl
38.0
40.6
48.0
(NH4)2SO4
24.9
32.2
−
KCl
21.0
27.8
38.4
ZnSO4
12.6
−
−
KNO3
9.0
−
−
K2SO4
4.2
5.1
7.5
3.1 SWRCs of highly-compacted GMZ bentonite The SWRCs of the highly-compacted GMZ bentonite following wetting path at different temperatures under unconfined and confined conditions are shown in Fig.4. It can be seen from Fig.4 that, the water retention capacity under both confined and unconfined compacted bentonite decreases with increasing temperature, and the influence increases with decreasing suction at a certain suction.
Fig.4 Comparison of SWRCs in unconfined/confined wetting paths at different temperatures
The mechanism for the influence of temperature on the water retention capacity of the highly-compacted bentonite can be analyzed in the aspect of the low suction and the high suction, respectively [7]. At high suction ( > 4 MPa), the change of clay fabric and intra-aggregate water plays a significant role in water retention capacity of GMZ bentonite. Much intraaggregate water moves into the macropore with increasing temperature. The excessive water flows out from the macropore, for degree of saturation is invariable in macropores at a certain suction. Therefore, the water retention capacity of bentonite decreases as the temperature increases. At low suction, capillary effect plays a decisive role in the performance of the water retention capacity. The changes of surface tension caused
J. Cent. South Univ. Technol. (2009) 16: 0821−0826
824
by the increase of temperature result in the increase of the water content of bentonite with increasing temperature at a certain suction. The effect of the constraint conditions on the water retention capacity of bentonite can also be analyzed in the aspect of the high and low suctions. At high suction, the influence of constraint conditions on the soil-water retention capacity of bentonite is not significant, which agrees with the result obtained by CHEN et al [16]. But at low suction, the water retention capacity of the confined specimen is clearly lower than that of unconfined specimen. The difference between water content of the compacted bentonite under the confined and unconfined conditions becomes greater with decreasing suction, which suggests that water retention capacity has a close relationship with the changes of the microstructure. Under the unconfined conditions, the inter-aggregate pores of bentonite expand constantly, and water can flow into these pores easily. Therefore, the water retention capacity of the unconfined specimen increases rapidly as the suction decreases. As clay particles can only swell and collapse into the macropores under confined conditions, the increasing rate of water content in the confined specimen is significantly lower than that in the unconfined specimen with the decrease of the controlling suction. In order to analyze the influence of temperature on the water retention capacity, a ratio (kt), which indicates that the water content changes with temperature, is defined as kt =
wt1 − wt2 wt1
×100%
Fig.5 Relationship between kt and suction (t1 is 40 ℃, and t2 is 80 ℃)
(1)
where wt1 and wt2 are the water contents in the SWRCs at temperature t1 and t2 for a given suction, respectively. The relationship between kt and the suction in temperature range from 40 to 80 ℃ is shown in Fig.5, indicating that the influence of temperature on the water retention capacity has a close relationship with the suction. And temperature has a great effect on the water retention capacity in the suction range from 40 to 80 MPa. It can also be seen from Fig.5 that the impact of constraint conditions on kt tends to increase with decreasing suction. 3.2 Hysteretic behaviour of SWRC The hysteretic characteristic curves for unconfined GMZ bentonite following the wetting/drying cycles in high suction at 20 and 40 ℃ are shown in Fig.6(a). It is quite obvious that the hysteresis loop of SWRC at 20 ℃ is larger than that at 40 ℃. That is to say, the hysteretic
Fig.6 Hysteretic characteristics of unconfined compacted GMZ bentonite at high suction and different temperatures: (a) Hysteretic characteristic curves; (b) Relationship between suction and hysteretic coefficient
behaviour of the compacted bentonite is less obvious as temperature increases. The hysteretic coefficient, η, was introduced to quantitatively describe the hysteretic behavior of bentonite of water retention curves following wetting/drying cycles, which can be expressed as
J. Cent. South Univ. Technol. (2009) 16: 0821−0826
η=
wd − ww ×100% ww
825
(2)
where wd and ww are the water contents in the drying and wetting paths at a given suction, respectively. Eq.(2) indicates that the hysteretic behaviour is less significant when η is small. The hysteretic coefficients of unconfined compacted GMZ bentonite changing with suction at 20 and 40 ℃ were calculated using Eq.(2). The results are given in Fig.6(b). Fig.6(b) shows that the hysteretic coefficients are all less than 7%, and decrease as the temperature increases, which indicates that the hysteresis of highlycompacted bentonite is not so significant. The hysteretic behavior of the unconfined compacted bentonite in different of ranges suction at 40 ℃ is shown in Fig.7. Fig.7(a) shows that the hysteretic cycle becomes larger with the decrease of suction. Fig.7(b) also indicates that hysteretic coefficients are lower than 5% at high suction (>4 MPa), and decrease with the increase of suction.
4 Conclusions (1) The water retention capacity of the highlycompacted GMZ bentonite decreases as the temperature increases. At the same time, the impact of temperature on the water retention capacity has a close relationship with the suction. (2) At a certain temperature, the influence of constraint conditions on the water retention capacity of the compacted bentonite is not obvious at high suction, but the water retention capacity of confined specimen is significantly lower than that of unconfined specimen at low suction. (3) The hysteretic behaviour of the compacted bentonite under unconfined conditions decreases as the temperature increases. At high suction (>4 MPa), the hysteretic behaviour of the unconfined bentonite tends to increase with decreasing suction. In summary, the hysteretic behaviour of compacted bentonite is not significant.
References [1]
WERSIN P, JOHNSON L H, MCKINLEY I G. Performance of the bentonite barrier at temperatures beyond 100 ℃: A critical review [J]. Physics and Chemistry of the Earth, 2007, 32(8/14): 780−788.
[2]
ROMERO E, VILLAR M V, LLORET A. Thermo-hydro-mechanical behaviour of two heavily overconsolidated clays [J]. Engineering Geology, 2005, 81(3): 255−268.
[3]
SA´NCHEZ M. Thermo-hydro-mechanical coupled analysis in low permeability media [D]. Barcelona: The Polytechnic University of Catalunya, 2004.
[4]
VILLAR M V, LLORET A. Dismantling of the first section of the FEBEX in situ test: THM laboratory tests on the bentonite blocks retrieved [J]. Physics and Chemistry of the Earth, 2007, 32(8/14): 716−729.
[5]
LLORET A, VILLAR M V. Advances on the knowledge of the thermo-hydro-mechanical
behaviour
of
heavily
compacted
‘‘FEBEX’’ bentonite [J]. Physics and Chemistry of the Earth, 2007, 32(8/14): 701−715. [6]
ROMERO E, GENS A, LLORET A. Temperature effects on the hydraulic behaviour of an unsaturated clay [J]. Geotechnical and Geological Engineering, 2001, 19(3/4): 311−332.
[7]
VILLAR M V, LLORET A. Influence of temperature on the hydro-mechanical behaviour of a compacted bentonite [J]. Applied Clay Science, 2004, 26(1/4): 337−350.
[8]
JACINTO A C, VILLAR M V, ROBERTO G E, LEDESMA A. Adaptation of the van Genuchten expression to the effects of temperature and density for compacted bentonites [J]. Applied Clay
Fig.7 Hysteretic behaviors of unconfined compacted GMZ bentonite in different suction ranges at 40 ℃ (B1 stands for hysteretic cycle at high suction and B2 stands for hysteretic cycle at low suction): (a) Hysteretic characteristic curves; (b) Relationship between suction and hysteretic coefficient
Science, 2009, 42(3/4): 575−582. [9]
ALONSO E E. Gas migration through barriers [J]. Chinese Journal of Rock Mechanics and Engineering, 2006, 25(4): 693−708.
[10]
PHAM H Q, FREDLUND D G, BARBOUR S L. A study of hysteresis models for soil-water characteristic curves [J]. Canadian Geotechnical Journal, 2005, 42(6): 1548−1568.
J. Cent. South Univ. Technol. (2009) 16: 0821−0826
826 [11] [12]
LI X S. Modelling of hysteresis response for arbitrary wetting/drying
pressure of densely compacted Gaomiaozi bentonite GMZ01 [J].
paths [J]. Computers and Geotechnics, 2005, 32(2): 133−137.
Chinese Journal of Rock Mechanics and Engineering, 2007, 26(S2):
NUTH M, LALOUI L. Advances in modeling hysteretic water
2861−3865. (in Chinese)
retention curve in deformable soils [J]. Computers and Geotechnics,
[18]
2008, 35(6): 835−844. [13]
Swelling-shrinkage behaviour of Gaomiaozi bentonite [J]. Chinese
LIU Y, ZHAO C G. Modeling the hysteresis for soil-water
Journal of Geotechnical Engineering, 2008, 30(7): 1005−1010. (in
characteristic curves [C]// New Frontiers in Chinese and Japanese
Chinese)
Geotechniques. Beijing: China Communications Press, 2007:
[19]
CUI Y J, DELAGE P. Yielding and plastic behavior of an unsaturated
[20]
YE Wei-min, TANG Yi-qun, CUI Yu-jun. Measurement of soil
383−392. [14]
XU Yan-bing, WEI Chang-fu, CHEN Hui, LUAN Mao-tian. A model
compacted silt [J]. Geotechnique, 1996, 46(2): 291−311.
of soil-water characteristics for unsaturated geotechnical materials
suction in laboratory and soil-water characteristics of Shanghai soft
under arbitrary drying/wetting paths [J]. Chinese Journal of Rock
soil [J]. Chinese Journal of Geotechnical Engineering, 2005, 27(3):
Mechanics and Engineering, 2008, 27(5): 42−45. (in Chinese) [15]
[16]
LIU Yue-miao, WEN Zhi-jian. Study on clay-based materials for the
347−349. (in Chinese) [21]
TANG A M, CUI Yu-jun. Controlling suction by the vapour
repository of high level ratioactive waste [J]. Journal of Mineralogy
equilibrium technique at different temperatures and its application in
and Petrology, 2001, 28(12): 19−21. (in Chinese)
determining the water retention properties of MX80 clay [J].
CHEN Bao, QIAN Li-xin, YE Wei-min, CUI Yu-jun, WANG Ju. Soil-water characteristic curves of Gaomiaozi bentonite [J]. Chinese Journal of Rock Mechanics and Engineering, 2006, 25(4): 788−793. (in Chinese)
[17]
QIN Bing, CHEN Zheng-han, LIU Yue-miao, WANG Ju.
YE W M, SCHANZ T, QIAN L X. Characteristics of swelling
View publication stats
Canadian Geotechnical Journal, 2005, 42: 1−10. [22]
LYTTON L. Isothermal water movement in clay soils [D]. Austn: University of Tekas, 1967. (Edited by CHEN Wei-ping)