when listening to music at all volumes. ... spacing is changed, all station presets are erased. Up to 18 FM stations and
MXD45
INSTALLATION/OWNER’S MANUAL AM/FM/CD Marine Receiver
MARINE
MXD45 INSTALLATION
Preparation Please read entire manual before installation.
Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. (consult a qualified technician if you are unsure) • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place.
TYPICAL FRONT-LOAD DIN MOUNTING METHOD 2
MXD45 INSTALLATION
Wiring Diagram
FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The MXD45 uses one 5 amp AGC fuse (Battery) located in-line.
* CAUTION - Do not attach any speaker leads to ground as severe damage will occur.
3
MXD45 OPERATION
Control Locations 1
2
3
20
4
19
4
18
17
5
16
15
14
13
7
8
11
10
6
12
1
Release
11
Auto Store/Preset Scan
2
Power
12
Display
3
Volume Up/Down
13
Scan
4
Audio
14
Local/Distance
5
Play/Pause
15
Preset 6
6
Bass Boost/Mono/Stereo
16
Preset 5
7
Tune/Track Up/Down
17
Preset 4
8
Band
18
Preset 3/CD Intro
9
Eject
19
Preset 2/CD Random
10
Mute
20
Preset 1/CD Repeat
9
MXD45 OPERATION
General Operation Faceplate Removal
Semi-permanent Faceplate Installation Power On/Off
CD Mode
Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Press PWR or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press PWR to turn the unit off. Insert a CD or press
l/ II to begin or resume playback.
Tuner Mode
Press PWR or BAND to begin or resume tuner operation.
Bass Boost
Press BASS to activate and deactivate bass boost curve. Activating this feature will enhance the bass frequencies when listening to music at all volumes.
Volume
Adjust volume using VOL t / VOL s (00-46).
Mute
Press MUTE to silence the audio. “MUTE” will appear in the display. Press MUTE again to cancel.
Display
Press DISP to display the clock. The radio frequency (tuner mode) or CD track/elapsed time (CD player mode) show by default.
Set the Clock
Press DISP to display the clock, then release. Press and hold DISP for 2 seconds, the clock will begin to flash. Press TUNE > to adjust the minutes. Clock settings will be saved after 5 seconds.
12/24-hour Clock
The clock will display 12-hour AM/PM time in U.S. frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00).
5
MXD45 OPERATION
General Operation Reset
Press and hold for more than 2 seconds to RESET the unit upon initial installation. The RESET button is located behind the faceplate. Refer to page 2 for details.
Audio
Press AUD to select between Volume (default), Bass, Treble, Balance & Fader. VOLUME
TREBLE
Bass
Press AUD until BA appears Press VOL t or s to adjust ( -7 minimum / 7 maximum)
Treble
Press AUD until TR appears Press VOL t or s to adjust ( -7 minimum / 7 maximum)
Balance
Fader
6
BASS
BALANCE
Press AUD until B appears Press VOL t (LEFT) or s (RIGHT) to adjust (BL 15/BR 15) BAL 00 represents equal balance.
Press AUD until F appears Press VOL t (FRONT) or s (REAR) to adjust (FF 15/FR 15) F 00 represents equal balance.
FADER
MXD45 OPERATION
Tuner Operation Seek Tuning Manual Tuning
Scan Tuning
Press TUNE > momentarily to seek the next strong station. Press TUNE > for more than 2 seconds, then release. “MANU” will momentarily appear in the display. Press TUNE > momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). “AUTO” will momentarily appear in the display. Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCAN again to cancel.
FM Local/Distance
Press LOC to activate local tuning for strong FM station reception only. Press LOC again to cancel and resume distance tuning (default).
FM Mono/Stereo
Press MO/ST for more than 2 seconds during FM tuner operation to select mono or stereo (default) reception of the broadcast signal.
Band Frequency Spacing
Storing and Recalling Station Presets
Press BAND to select between FM1, FM2, FM3 and AM1, AM2 bands. Press and hold BAND then press TUNE > to select U.S. frequency spacing (default). Anytime frequency spacing is changed, all station presets are erased. Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button for more than 2 seconds. When stored, the preset number will appear in the display. The station can be recalled anytime by pressing the corresponding preset button.
Automatically Store Stations
Press AS/PS for more than 2 seconds to automatically store the six strongest stations in the current band.
Preset Scan
Press AS/PS for less than 2 seconds to scan presets 1-6 on the current band, pausing for 5 seconds at each. Press AS/PS again to cancel.
7
MXD45 OPERATION
CD Player Operation Insert CD
With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback.
Eject CD
Press EJECT to eject the CD. The unit will change to tuner mode. If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD.
Track Select
Press TRACK >> to skip to the beginning of the next track. Press TRACK or TRACK 92dB Frequency response: 10Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit
FM Tuner
Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz
General
Total power output: 120 Watts Peak Power output: 30Wx4 @ 4 ohm, 14.4 VDC Operating voltage: 11-16 VDC, negative ground Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm) Design and specifications subject to change without notice.
11
www.dualav.com ©2005 Dual Electronics Corp. NSA1005-V01