Reconnect wires from side tubes according to wiring shown on page. 9. ... Saturn.
Cutoff LED, scan here. 4. 5. BLACK. Wires from. Side Tube. Cap with. Attached ...
Saturn Cutoff LED and Saturn 2 Cutoff LED Installation Instructions: Post Top Tools Required (not included) 4mm Allen Wrench #10 Spanner Head Driver SAC2L
(shown for reference)
1. Run Feed Cord from Luminaire into top of Pole (fixture does not need to be opened; it ships ready to install). 2. Place Luminaire onto Pole. 3. A im the fixture as intended. Always position Street Side Label at street side (see label next to glass). 4. Level and secure into place by tightening (2) Set Screws with Allen Wrench. 5. L oosen Handhole Screws and remove Handhole Cover. Connect Feed Cord from Luminaire to Line Voltage Feed (by others). See wiring on page 4 for proper installation. Be sure not to pinch wires during installation. 6. Replace Handhole Cover and test fixture.
SACL Luminaire
10 5/16" [262mm] Driver Depth
4 1/8" [105mm] Fitter Depth, Ref
#10 Spanner Head Driver
Set Screws (4mm Allen Wrench)
Pole
Feed Cord (from Luminaire)
Handhole Cover
3 1/8" [79mm] Minimum Pole I.D. Pole
For details and spec sheet for Saturn Cutoff LED, scan here.
CAUTION
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs are exposed.
Only work on de-engergized equipment. Disconnect power before wiring fixture.
Do NOT stare into Beam. Can cause eye damage.
Contact will cause electric shock or burn.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for handling electrostatic sensitive devices.
Page 1 of 5 (Rev. 07/14) SACL_INST_v3.3
Saturn Cutoff LED and Saturn 2 Cutoff LED Gear Tray Maintenance Tools Required (not included) #10 Spanner Head Driver Phillips Head Screwdriver
1. Disconnect Power. 2. Loosen Handhole screws and remove Handhole Cover (not shown). Disconnect luminaire Feed Cord from Line Voltage Feed (not shown). 3. T wist lower cover counter-clockwise to remove cover. 4. Loosen (2) M6 pan head screws (do not remove screws). 5. T urn gear tray counter-clockwise and lift Gear Tray Assembly out of pole, just enough to expose terminal blocks. 6. Disconnect white, black and green wires coming from side tubes. Remove Gear Tray Assembly from pole along with the attached Feed Cord from Luminaire. 7. Run Feed Cord from the new Gear Tray Assembly into Pole. 8. P lace New Gear Tray Assembly partly into pole exposing the terminal blocks. Reconnect wires from side tubes according to wiring shown on page. 9. Reinstall Gear Tray Assembly. Tighten (2) M6 pan head screws. Reinstall lower cover. 10. C onnect the new Feed Cord from Luminaire to Line Voltage Feed. 11. Replace Handhole Cover and test Luminaire.
Connect WHITE Wire from Side Tubes with RED Wire from Gear Tray Assembly Connect BLACK Wire from Side Tubes with BLACK Wire from Gear Tray Assembly Top Terminal Block RED BLACK
WHITE BLACK
Wires going to the rest of the Gear Tray Assembly
GREEN
GREEN
WHITE BLACK GREEN
Wires from Side Tube
Bottom Terminal Block Connect GREEN Wire from Side Tubes with GREEN Wire from Gear Tray Assembly
3 5 4
(Phillips Head) Top Terminal Block Bottom Terminal Block
6
For details and spec sheet for Saturn Cutoff LED, scan here.
CAUTION
Wires from Side Table
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs are exposed.
Only work on de-engergized equipment. Disconnect power before wiring fixture.
Do NOT stare into Beam. Can cause eye damage.
Contact will cause electric shock or burn.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for handling electrostatic sensitive devices.
Page 2 of 5 (Rev. 07/14) SACL_INST_v3.3
Saturn Cutoff LED and Saturn 2 Cutoff LED Light Engine Maintenance Tools Required (not included) #14 Spanner Head Driver Bit Phillips Head Screwdriver
1. Disconnect power. 2. Loosen tamper-resistant screws using spanner head screwdriver. 3. L ift cap off fixture and disconnect red, black, and green wire connections. 4. Loosen (9) MS pan head screws holding light engine to cap (do not remove screws). 5. Remove light engine assembly by using keyhole design. 6. Replace with new light engine, tighten screws and connect red, black and green wires according to wiring shown on page. Ensure gasket is clean and damage-free. 7. Replace top cap making sure not to pinch wires and tighten tamper-resistant screws. 8. Reconnect to power and test luminaire.
Wire connection detail for #3 and #6 Wire Connectors
WHITE
RED
BLACK
BLACK
GREEN
GREEN
Wires from Side Tube
Cap with Attached Light Engine
3
2
4
5 For details and spec sheet for Saturn Cutoff LED, scan here.
CAUTION
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs are exposed.
Only work on de-engergized equipment. Disconnect power before wiring fixture.
Do NOT stare into Beam. Can cause eye damage.
Contact will cause electric shock or burn.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for handling electrostatic sensitive devices.
Page 3 of 5 (Rev. 07/14) SACL_INST_v3.3
Saturn Cutoff LED and Saturn 2 Cutoff LED Wiring US: Post Top
HI-LO SWITCHING OPTION (HLxx) WIRING
Hi-Lo Switching Option (HL) Wiring LG3700 and LG3105, 120V, 240V, 277V. When red is energized, light output will be at “Lo” level.
Standard Single Wiring & Dynadim (DMY)
120/240/277V. WHEN RED IS ENERGIZED, LIGHT OUTPUT WILL BE AT "LO" LEVEL. SPECIFY THE "LO" OUTPUT LEVEL BY SELECTING FROM THE TABLE BELOW. FOR OTHER PERCENTAGE OUTPUT LEVELS, CONSULT FACTORY.
SURGE PROTECTOR
SURGE PROTECTOR
BLACK
L1 FROM LINE CORD
L1 N
WHITE
N
GREEN
LIGHT ENGINE
0-10V DIMMING WIRING FOR 120-270V
WHITE GREEN
FROM LINE CORD
L2
0-10V Dimming Option (DM) Wiring LG3700 and LG3105, 120-277V.
BLACK
347/480 V
RED
STANDARD WIRING FOR 347/480V
SURGE PROTECTOR
SURGE PROTECTOR
N
BLACK
L1 FROM LINE CORD
WHITE GREEN
FROM LINE CORD Dim (+)
RED
Dim (-)
ORANGE
RELAY
STANDARD WIRING FOR 347/4800V WITH NO ADDITIONAL OPTIONS
100% LIGHT OUTPUT AT 10V, DOWN TO 10% LIGHT OUTPUT AT 0V.
L1
LIGHT ENGINE
N
LIGHT ENGINE
CAUTION
AUTO TRANSFORMER
BLACK WHITE GREEN
LIGHT ENGINE
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs are exposed.
Only work on de-engergized equipment. Disconnect power before wiring fixture.
Do NOT stare into Beam. Can cause eye damage.
Contact will cause electric shock or burn.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for handling electrostatic sensitive devices.
Page 4 of 5 (Rev. 07/14) SACL_INST_v3.3
Saturn Cutoff LED and Saturn 2 Cutoff LED Shade Replacement Tools Required (not included) #14 Spanner Head Driver Bit Phillips Head Screwdriver 13mm Wrench
Wire connection detail for #3 and #7 Wire Connectors
WHITE
RED
BLACK
BLACK
GREEN
GREEN
Wires from Side Tube
1. Disconnect power. 2. Loosen tamper-resistant screws using spanner head screwdriver. 3. L ift cap off fixture and disconnect red, black, and green wire connections. 4. Remove (2) hex nuts and flat washers, and (2) pan head screws holding shade in place. 5. Remove and replace shade. 6. Reinstall (2) hex nuts and flat washers, and (2) pan head screws to secure the shade. 7. Reconnect red, black, and green wires according to wiring shown on page. Ensure gasket is clean and damage-free. 8. R eplace top cap making sure not to pinch wires and tighten tamper-resistant screws. 9. Reconnect to power and test luminaire.
Cap with Attached Light Engine
3
4
2 5
For details and spec sheet for Saturn Cutoff LED, scan here.
CAUTION
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs are exposed.
Only work on de-engergized equipment. Disconnect power before wiring fixture.
Do NOT stare into Beam. Can cause eye damage.
Contact will cause electric shock or burn.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for handling electrostatic sensitive devices.
Page 5 of 5 (Rev. 07/14) SACL_INST_v3.3