Sensor A,D have problem (E2: 2 damaged sensors). Volume adjustment. PTS400Q1. PTS400Q4. PTS400W1. PTS400T. Self-test fun
Wireless parking assist system PTS400W1 PTS400Q1 PTS400Q4 PTS400T
Think safety think Steelmate
Steelmate Co., Ltd. All rights reserved. The right to change the design and specifications reserved. The trademark, patent and copyright are owned by Steelmate Co., Ltd.
STEELMATE CO., LTD Steelmate Industrial Park, Heping Street, Dongfu Road, Dongfeng Town, Zhongshan City, Guangdong, P.R. China 528425
PRI0775/A
Manual
Contents User Manual
Installation Manual
Important notice ---------------------------------------- 02
Packing list ---------------------------------------------- 15
Disclaimer -----------------------------------------------
02
Installation tools ---------------------------------------- 15
About the product -------------------------------------
03
Sensor installation ------------------------------------- 16
Key features --------------------------------------------
03
ECU installation ---------------------------------------- 20
Specifications ------------------------------------------- 03
Buzzer & display installation ------------------------ 21
Display & Buzzer --------------------------------------
04
Function testing ---------------------------------------- 22
Volume adjustment ------------------------------------ 06
Wiring diagram ----------------------------------------- 23
Self-test function ---------------------------------------
07
Troubleshooting ---------------------------------------- 24
Attention -------------------------------------------------
10
Sensor maintenance ---------------------------------- 10 How does the system work -------------------------
11
01
Important notice
About the product
This parking assist system helps to provide assistance when reversing and parking. Driving skills, such as slowing down, use of mirrors etc. is always essential.
Parking assist system is an ultrasonic distance monitoring system. It electronically detects the area behind your vehicle while reversing, and alerts you with audible tones and display if the system detects an obstacle. The system will show the accurate distance in meters or feet depending on your region.
1. This unit is for vehicles with 12V DC. 2. Unit should be installed by a professional auto technician. 3. Route wiring harness away from heat sources and electrical components.
User Manual
4. It is strongly recommended to check the position of the sensors before the actual drilling of the holes screw. 5. Perform a test after installation.
Key features 4 rear sensor system Wireless from control unit to buzzer/display Easy installation Volume adjustable Self-test function All weather design (-40°C~+85°C/-40°F~+185°F)
PTS400W1/PTS400Q1/PTS400Q4/PTS400T is a 4-sensor rear wireless parking assist system, from control unit to buzzer/display is wireless. Each part of this product has passed the most stringent test before releasing to the market. It is reliable at a wide temperature range (-40°C ~ +85°C/-40°F~+185°F) and becomes very useful when you are parking in poor weather conditions. With the help of parking assist system, you can enjoy a convenient and easy parking experience.
Specifications Input voltage: 12V±3V Detection range: 0.1~2.5m/0.3~8.2ft Alarm range (Buzzer): 0.3~1.5m/1.0~4.9ft
Disclaimer
Alarm range (Display): 0.3~2.5m/1.0~8.2ft
The parking assist system is designed as a driver assistance device, and should not be used as a substitute for safe parking practices. The area into which the vehicle is to be reversed must be constantly visually monitored while parking.
Operating temperature: -40°C~+85°C/-40°F~+185°F
Beep SPL: 70~90 dB
The manufacturer and its distributors do not guarantee or assume liability for collisions or damages while reversing your vehicle. 02
03
Display & Buzzer PTS400Q1 Matrix indication
PTS400W1 Distance Meters/feet Volume adjustable button
LED indicator
Voice on/off button Volume adjustable button Built-in buzzer
Volume adjustable switch
PTS400Q4
Matrix indication
Built-in buzzer
04
PTS400T
Distance Meters/feet
Volume adjustable switch
Matrix indication
Volume adjustable switch
Distance Meters/feet
Built-in buzzer
05
Volume adjustment
Self-test function
PTS400Q4
PTS400Q1 & PTS400Q4 The system will test all the sensors when the reverse gear is engaged. If all the sensors are working normally, the system will beep once and the LED display will flash once. If there is any problem with the sensors, the system will beep three times to indicate that one or more sensors have problems.
PTS400Q1
Damaged sensor locations
Number of damaged sensors
PTS400T
Sensor A has problem(E1:1 damaged sensor)
Sensor A,D have problem (E2: 2 damaged sensors)
PTS400W1
Once the reverse gear is engaged, press and hold " " button for 2 seconds to turn on/off the voice alarm
06
07
PTS400T The system will test all the sensors when the reverse gear is engaged. If all the sensors are working normally, the system will beep once and the LCD display will flash once. If there is any problem with the sensors, the system will beep three times to indicate that one or more sensors have problem with the green backlight turns on. The damaged sensor’s position----A, B, C, or D will be shown on the display. The number after “E” indicates the total number of the damaged sensors .
All sensors are working
AB
CD
ft m Beep once
AB
CD
ft m
The total number of the damaged sensors
PTS400W1 The system will test all the sensors when the reverse gear is engaged. If all sensors are working normally, the buzzer will beep once. If a damaged or defective sensor is detected, then the system will: Beep three times Other sensor will continue to work normally.
1. All sensors are working normally
Be--The damaged sensor’s position
AB
CD
ft Sensor A has problem m (E1: 1 damaged sensor)
AB
CD
ft m
Sensors A and D have problems (E2: 2 damaged sensors)
2. Damaged sensor is detected Be---Be---Be---
08
09
Attention False detection may occur in the following situations:
Sensor maintenance
How does the system work PTS400W1 & PTS400Q1 & PTS400Q4
Do not wash the sensor with a pressure washer of scrub them forcibly.
Matrix zone
Buzzer
Please wash car with lowpressure water.
Be Please melt the ice with water when the sensors are covered by ice.
* After installation, please fully test the system before use. * Heavy rain, dirty or damanged sensors may cause false warning occasionally. * Ensure that the self-test procedure is completed and all sensors are functioning before using the system. 10
Please clean the sensors with cloth or low-pressure water when the sensors are covered by dirt or snow.
Be
2.5m/8.2ft
AB
CD
ft m
The obstacle distance is >2. 5m/8.2ft, the white backlight will turn on with the 1st stage flashing.
12
Distance: 2.5m/8.2ft ~1.5m/4.9ft
AB
CD
ft m
The obstacle distance is 2.5m/8. 2ft ~1.5m/4.9ft, the blue backlight will turn on with the 1st stage flashing.
Distance: 1.5m/4.9ft ~ 1.0m/3.3ft
AB
CD
ft m
The obstacle distance is 1.5m/4.9ft ~ 1.0m/3.3ft, the green backlight will turn on with 1st ~3rd stage flashing.
Distance: 1.0m/3.3ft ~ 0.6m/2.0ft
AB
CD
ft m
The obstacle distance is: 1.0m/3. 3ft ~ 0.6m/2.0ft, the orange backlight will turn on with 1st~5th stage flashing.
Distance: 0.6m/2.0ft ~ 0.3m/1.0ft
AB
CD
ft m
When the obstacle distance is 0.6m/2.0ft ~ 0.3m/1.0ft, the red backlight will turn on with 1st~7th stages flashing.
Distance: < 0.3m/1.0ft
AB
CD
ft m
When the obstacle distance is less than < 0.3m/1.0ft, the red and white backlight will flash alternately. All 7-stage will flashing.
13
Packing list
PTS400Q4
PTS400Q1
PTS400T
PTS400W1
Installation Manual Manual
The actual sensor may vary from the image shown above
Installation tools
45' ~ 60' 14
15
Sensor installation Pls adjust the sensor angle according to sensor height and bumper angle, avoid detecting to ground.
2
H > 0.45m/1.5ft H < 0.65m/2.1ft
< 0.45m/1.5ft
< 0.45m/1.5ft
< 0.45m/1.5ft
1
H > 0.65m/2.1ft
16
0.45m/1.5ft < H < 0.65m/2.1ft
H < 0.45m/1.5ft
c
b
a
a = 1/8L b = 2/8L c = 1/8L
a
b
c
Check the size of the hole saw packed in the product matches the diameter of the sensors before drilling any holes.
17
3
4
6
D A
B
C
5
18
D
D
C
C
B
B
A
A
19
ECU installation
Buzzer & display installation
12V PARKING ASSIST SYSTEM
A
20
B
C
D
And
21
Function testing
Wiring diagram
Red
12V
PARKING ASSIST SYSTEM
Reversing light
Display
Buzzer Black
.9ft 1.5m/4
ACC GND
GND
Function test is performed by holding a wooden board (0.3 x 1m/1.0 x 3.3ft) standing at the back of the car, and reverse the car slowly to test each function respectively as shown in this manual.
22
23
Troubleshooting After installation, the buzzer & display doesn’t work a) Are all wires connected properly? b) Is the vehicle’s ignition ON? c) Is the reversing gear engaged (the reversing light should be turned on)? Damaged sensor detected a) Are all sensors plugged into the ECU correctly and tightly? b) Is the sensor faulty? c) Is the sensor covered by dirt or snow? d) Is the sensor damaged? False warning a) Are all sensors plugged into the ECU in the correct position tightly? b) Does any sensor detect the ground? c) Does rubber ring in the sensor come out (14D sensor)? Warning sound is too low or too high a) Press the volume button to adjust the volume to a suitable level. If the problem persists, please follow these steps a) For consumer: contact your dealer or nearby service centre. b) For installer or dealer: 1) Test the sensors with certified ECU by using a flat wooden board. 24
2) Replace the ECU and recheck the system. 3) Plug the certified sensors into the ECU and recheck. 4) Email your question to us and we will reply ASAP.
