Evaluation of Microstructures and Mechanical Properties of ... - Core
Recommend Documents
Feb 15, 2016 - Keywords: stainless steel; austempering; bainite; mechanical properties. 1. ... Austempering heat treatment can produce excellent mechanical ...
Feb 15, 2016 - Keywords: stainless steel; austempering; bainite; mechanical properties. 1. Introduction. SUS440 is a high-chrome and carbon martensite ...
Abstract. Nano-structured TiN/VN coatings with a range of bi-layer periods from 3.4 to 11.0 nm were deposited on ferromagnetic 410 stainless steel (410SS) and ...
Nov 18, 2013 - Institute of Nanomaterials, Chinese Culture University, Taipei 111, ..... 316-L femoral implants by deposition of thin films. Surf. Coat. Tech. 2001 ...
Mar 2, 2018 - Nano and Heterogeneous Structural Materials Center, School of ... strength and uniform elongation, which may be attributed to the high density .... on a scanning electron microscope (SEM, Quant 250 FEG, FEI, Hillsboro, OR, ...
May 21, 2018 - in comparison with common clay. In general, most red- layers have high water content, high plasticity, large pore ration, and low density, the ...
Feb 25, 2018 - high-energy-density, low-heat-input electron beam (EB) welding and low-energy-density ... have properties similar to those of intermetallics (i.e..
Published Online October 2012 (http://www.SciRP.org/journal/jmmce) ... were used on the cast alloy to influence its mechanical properties. The selected heat .... barrier in the course of casting, sand casting was selected as a the best means of ...
mechanical properties of Nb-silicide in situ composites[17â20]. Therefore, Nb-Si alloys are prepared by directional solidification in an optical floating zone.
severely by equal-channel angular pressing and high pressure torsion ... of the tensile strength was promoted with admissible penalization on ductility.
widely used e.g. in the chemical, energy and biomedical industries [6]. ..... [9] R.H. Morgan, A.J. Papworth, C. Sutcliffe, P. Fox, W. O'Neill, High density net shape.
Materials Science and Engineering A247 (1998) 229â238 ... FAMU-FSU College of Engineering, 2525 Pottsdamer St., Tallahassee, FL 32310-2175, USA.
72. Microstructures and Mechanical properties of Spray deposited and Heat-treated Al-25Mg2 Si-2Cu alloy. Dayanand M. Goudar. (Corresponding author).
Mar 24, 2014 - time-saving and cost-effective compared to conventional casting technology. ... scanned metal powders according to the sliced data to obtain a lay- ... shape was captured using software (3Shape D800, 3Shape A/S,.
Cold-rolled Medium-Mn Steels with Different Annealing. Processes. Jun HU,1,2)* ..... 4) Z. Zhang, K. Manabe, Y. Li and F. X. Zhu: Steel Res. Int., 83 (2012),. 645.
properties of waste rubber/natural rubber composite ... thermal insulation and high mechanical properties and decreases the cost of materials to 82% of.
Keywords: Electroless Nickel coating; 7075-T6 aluminum alloy; Fracture .... at the maximum load, due to the tensile stress, resulting in plastic deformation.
Mar 1, 2013 - Parts Fabricated by Selective Laser Melting and Electron ... platform. A focused laser/electron beam scans the powder-bed- based on the sliced ...
This paper present the study about the mechanical properties of two high strength low alloy steels for replacing the current rolled homogeneous armour (RHA) ...
Jun 27, 2013 - JUN HU, Ph.D. Candidate, LIN-XIU DU, Professor, CAI-RU GAO, ... AN-YANG WANG, Researcher, is with the AVIC Shenyang Aircraft.
Journal of Metals, Materials and Minerals, Vol.18 No.2 pp.191-197, 2008. Effect of Heat Treatment on ... critical cooling rate of selective alloy. Therefore, any raw material that will be treated must be firstly analyzed to know chemical ...
Dec 4, 2011 - tensile properties of full lamellar microstructures after heat ... The lamellar spacing of FL structure decreases with the increase of cooling rate.
Mar 19, 2008 - During the manufacturing process for products such as big cylindrical pipes for cryogenic fuel tanks using FSW, the double-FSW method has to ...
Evaluation of Microstructures and Mechanical Properties of ... - Core
welding of aluminium to copper for defence applications. .... toughness of the resulted welds is recorded at with increase in forging pressure and increase in ...
