Addressable RGB Flex Led Strip. 1 Meter with 32 pcs 5050 LEDs. Applications:
The excellent light and user-friendly designs make LED strip perfect for ...
These sensors consist of two transmitter(s) and one receiver mounted on one ... a USB to serial board, Mini-B USB cable,
iColor Flex MX is a multi-purpose, high-intensity strand of 50 full-color LED nodes
for generating extraordinary effects without the constraints of fixture size or ...
TECHNICAL DATA. MQ-4 GAS SENSOR. FEATURES ... A. Standard work condition. Symbol. Parameter name. Technical condition. R
WIKA S-10 and S-11 pressure transmitters are precision engineered to fit most ...
of electrical connection and process connection options are avail- able to meet ...
Dec 1, 2006 - Example: Air purifier, Air conditioner, Air monitor. 1. ... In addition it can distinguish smoke from hous
SparkFun. ATmega328 with Arduino Optiboot (Uno) sku: DEV-10524. Description
: The name says it all on this one. An ATmega328 in DIP package, pre-loaded ...
SparkFun. Joystick Shield Kit sku: DEV-09760. Description: The Joystick Shield
kit contains all the parts you need to enable your Arduino with a joystick!
I Serial port clock for testing mode. TIO ... Source Current ... No load on X1, X2, .... Open. 10uF. 22uF. OM01. Optical
The four-pin connection provides for easy installation or ... Chemical Resistance: Contact Precon for data on resistance
May 26, 2011 - Choice of output format â direct pellistor replacement, industry standard 0.4 to 2 volts dc ... email: [email protected] Ù www.dynament.com.
XYZ Interactive Technologies, Using the ZX SparkFun sensor for Arduino. Introduction ... starting application and use th
Dec 3, 2012 ... Data access in Flex compared to other technologies . .... xmlns:mx="library://ns.
adobe.com/flex/halo" minWidth="1024" minHeight="768".
Jul 1, 2008 - The BMP085 digital pressure sensor is functionally compatible to the existing Bosch. Sensortec SMD500 digi
Description. Cooper Bussmann® PowerStor® supercapacitors are unique, ultra-
high capacitance devices utilizing electrochemical double layer capacitor ...
Note: Before using this information and the product it supports, be sure to read
the general information under “Notices” on page 85. First Edition (August 2013).
Page 1 ... admire Tina Turner for her commitment to Buddhism, but we find. Pat
Boone—who after all, had more hit records—rather weird for being explicitly ...
"The impedance buffer in the [Basic Flex Sensor Circuit] (above) is a single sided operational amplifier, used with thes
Special Edition Length
Features - Angle Displacement Measurement - Bends and Flexes physically with motion device - Possible Uses - Robotics - Gaming (Virtual Motion) - Medical Devices - Computer Peripherals - Musical Instruments - Physical Therapy - Simple Construction - Low Profile
Mechanical Specifications
Electrical Specifications
-Life Cycle: >1 million -Height: 0.43mm (0.017") -Temperature Range: -35°C to +80°C
-Flat Resistance: 25K Ohms -Resistance Tolerance: ±30% -Bend Resistance Range: 45K to 125K Ohms (depending on bend radius) -Power Rating : 0.50 Watts continuous. 1 Watt Peak
Dimensional Diagram - Stock Flex Sensor PART LENGTH 73.66 [2.900] ACTIVE LENGTH 55.37 [2.180]
6.35 [0.250]
How to Order - Stock Flex Sensor FS
L
0055
253
Series
Model
Active Length
Resistance
FS = Flex Sensor
L = Linear
0055 = 55.37mm
253 = 25K Ohms
ST Connectors ST = Solder Tab
How It Works Flat (nominal resistance) 45˚ Bend (increased resistance) 90˚ Bend (resistance increased further)
spectrasymbol.com
Rev A2 - Page 1
(888) 795-2283
Schematics
Following are notes from the ITP Flex Sensor Workshop "The impedance buffer in the [Basic Flex Sensor Circuit] (above) is a single sided operational amplifier, used with these sensors because the low bias current of the op amp reduces errer due to source impedance of the flex sensor as voltage divider. Suggested op amps are the LM358 or LM324." "You can also test your flex sensor using the simplest circut, and skip the op amp." "Adjustable Buffer - a potentiometer can be added to the circuit to adjust the sensitivity range."
"Variable Deflection Threshold Switch - an op amp is used and outputs either high or low depending on the voltage of the inverting input. In this way you can use the flex sensor as a switch without going through a microcontroller."
"Resistance to Voltage Converter - use the sensor as the input of a resistance to voltage converter using a dual sided supply op-amp. A negative reference voltage will give a positive output. Should be used in situations when you want output at a low degree of bending."
