INSTRUMENTATION In this experiments you will learn about basic ...

INSTRUMENTATION In this experiments you will learn about basic principles of Wheatstone bridge, operational amplifier and strain gauge.Related theory is given below, in three parts

ASSIGNMENT-I : THE BASIC WHEATSTONE BRIDGE CONTENT: The basic behaviour of a Wheatstone Bridge is introduced. The advantages of bridge measurement techniques over simple Ohm’s Law methods are investigated. EQUIPMENT REQUIRED: Qty Designation 1 TK2941M 1 1 1 1 1 1 1

-

Description Measurements Package Power Supply, ±15V dc (eg Feedback PS 446) Decade Resistance 1Ω to 100kΩ * DC Voltmeter 15V * Center zero dc milliammeter Resistor - 100Ω, 1W Resistor – 1kΩ, 1/8W Resistor – 10kΩ, 1/8W

PRACTICALS: 2.1 The basic Wheatstone Bridge OBJECTIVES: When you have completed this assignment you will: 1. Know the principle of operation of the basic Wheatstone Bridge. 2. Know how to measure resistance using a Wheatstone Bridge. KNOWLEDGE LEVEL: Before starting this assignment you should: 1. Understand the theory and application of Ohm’s Law. 2. Be familiar with the operation of series/parallel dc circuits and potential divider circuits. INTRODUCTION: The Wheatstone Bridge which was not direct reading: A method of determining resistance has many sources of error. A direct reading method with few errors would be of great advantage. A way of determining resistance value which only requires one meter is shown in the circuit of fig 4.2.1.

1

Rs standard resistor

+ Vs known voltage -

+ V -

Rx unknown

Fig 4.2.1 Basic one meter measurement Here, the unknown resistance, Rx is used in a potential divider circuit with a known standard resistor Rs connected across a known source voltage Vs. By the potential divider formula:

V=

Rx ⋅ Vs Rs + Rx

V ⋅ Rs Vs − V This circuit suffers from some disadvantages. Obviously Rs, the standard resistor, must be known precisely. The voltmeter V must have a resistance very much greater than Rx for accurate results. The method does not lead to direct reading of the result. When all the circuit values are known precisely, the final accuracy still depends ultimately on the accuracy of the meter indication.

therefore

Rx =

This draw back can be over come by Wheatstone bridge circuit shown in following fig.

2

Fig 4.2.5 Circuit of Wheatstone Bridge

Now, let us investigate circuit. Set up the module as shown in fig 4.2.6. this corresponds to the circuit of fig 4.2.5.

3

4

5

ASSIGNMENT -II OPERATIONAL AMPLIFIER CONTENT: The operation of the Operational Amplifier is investigated. EQUIPMENT REQUIRED: Qty Designation 1 TK2941M 1 2

-

Description Measurements Package Power Supply, ±15V dc (eg Feedback PS 446) DC Voltmeter 15V

PRACTICALS: 5.1 The basic Op Amp 5.2 Common Mode Gain OBJECTIVES: When you have completed this assignment you will: 1. Understand the operation of the basic operational amplifier. 2. Know how to connect up an operational amplifier to act as a voltage amplifier. 3. Understand the terms ‘differential gain’ and ‘common mode gain’. KNOWLEDGE LEVEL: Before starting this assignment you should: 1. Understand the theory operation of the potential divider circuit.

6

INTRODUCTION:

7

8

Connect the circuit as shown in fig 4.5.4

9

10

PRACTICAL ASPECTS

11

ASSIGNMENT-III :STRAIN GAUGEES CONTENT: The application of variable length transducer principle to strain gauge tranducers is investigated EQUIPMENT REQUIRED: Qty Designation Description 1 TK2941A Instrumentation Module 1 TK294 Linear Tranducer Test Rig 1 TK294E Strain Gauge Sub-unit 1 Power Supply ±15V dc 1 DC Voltmeter 15V PRACTICALS: Basic Strain Gauge OBJECTIVES: Know how the change in resistance of material,caused by a change in its physical dimension,can be used to measure the strain in the material. INTRODUCTION

12

13

Connect the circuit as shown in fig 4.10.3

14

15

16