4-Locking screw. 5-External measuring jaws. 1. The caliper is dustproof and waterproof (IP67). The measuring methods are
Please clean the measuring faces and beam with soft cloth, then close the external jaws. If the needle does not point at
Parts Diagram… ... IMPORTANT. Servicing requires extreme care and
knowledge and should be performed only by a qualified ... Use only 3-wire
extension cords that have 3-prong grounding plugs, and 3-pole receptacles that
accept the tool's ...
iacare ol'tltc Erimï¬ IIIIICdUEIIII. ' Press and hold lrutltin D to show the alarm time arid release it to restore the
SUNDYNE. LMV-333 PUMPS. Instruction and Operation. Manual. August 2007.
Page 2. Copyright. All rights reserved. .... Pump Control During Start-Up ..
Rated insulation voltage of a circuit (Ui). 440 V. Rated impulse withstand voltage of the assembly (Uimp). Line/input 8
instruction system (VAMOIS) to assist technicians take ... should be paid attention by technicians. ... automotive interior, offering a new way to the concep-.
We are glad you have chosen to purchase a PANASONIC microwave oven.
Before ... oven for reheating and defrosting, with Panasonic's Inverter Technology
.
VR&AR Combined Manual Operation Instruction System on Industry. Products: A Case Study. Xuyue Yin, Yan Gu, Shiguang Qiu, Xiumin Fan. CIM Research ...
This manual provides instructions and procedures necessary to install, operate ...
seal between the electromagnetic and hydraulic sections of the valve.The two.
Feb 6, 1999 ... Fire Alarm Control Panel IQ8Control C/M. 2. FB 798950.10.GB0 / 08.09. Intended
purpose. This product must only be used for the applications ...
A. PURPOSE OF THE MANUAL. This manual is expressly intended to provide
sufficient information for qualified technicians experienced in diesel engines and
...
transpose operation using the 256-bit Intel advanced vector extension (AVX) instructions. We present a novel vector-based matrix transpose algorithm and its ...
3 Apr 2000 ... CB-60/CB-80 Cr. CB-60/CB-80 Cryobath Low Temperature emperature. Table of
Contents le of Contents. PREFACE. Compliance .
You can start to use PC-Dmis. Start new part program, only one program can be
online to use CMM ( others are off-line). Unit can be inch (for IE 415) or mm as.
500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000. 2705 ... MIL-
L1000-CG ... This manual is intended to reinforce and review safety techniques.
(03:00:14) - Free Download Linux Programmers Operation System Instruction Pdf. Free Ebooks Download. * Read or Download
Among forms of creative language, verbal humor has received some attention in the computational milieu. Some aspects of irony and wordplay could be ...
At any state ,press A key EL backlight for 3s . Alarm Setting. ⢠in normal display Mode, press B key once enter into A
most-educated generation in U.S. history. Yet despite their heavy investment in education, Millennials currently have th
This is an automatic mechanical watch with manual winding mechanism. • If the
watch .... phones, magnetic necklaces, etc., it may gain or lose time. • If the watch
...
Service Operation. A hi i ff ti d ffi i i th. Achieving effectiveness and efficiency in
the delivery and support of services so as to ensure value for the customer and ...
Please clean the measuring faces and beam with soft cloth, then close the external jaws, make sure that the zero lines o
OPERATION INSTRUCTION Vernier Caliper Series 1205
2. Please clean the measuring faces and beam with soft cloth, then close the external jaws, make sure that the zero lines of the vernier and main scales coincide and there is no slit observed between the jaws against the light.
Caution: Do not measure the workpiece if it is rotating, this is dangerous and measuring faces will be worn out Graduation
3. To get accurate measurement, it is necessary to control the force. During measurement, please always apply constant and proper force on the thumb clamp. The measuring jaws should ''hold'' the workpiece and can still ''slide'' on the workpiece. 4. The reading is obtained by adding the reading of the vernier scale to that of the main scale. Take the vernier scale reading at the graduation which coincides with the one on the main scale. Details please refer to following figures. Graduation: 0.02mm
4
10
15mm
20
0
30
1
2
40
3
4
50
5
6
1
6
7
8
0
9
mm Vernier scale reading: 0.58mm
10
Step measurement
15.58mm
0.008''(0.001×8)
5
10
15
20
25
1 2 3 4 5 6 7 8 9
1
Main scale reading: 0.525'' Vernier scale reading: 0.008''
0.001in
1 2 3 4 5 6 7 8 9
2
1 2 3 4
Reading:
0.533''
Graduation: 0.05mm
6-Vernier with vernier scale 7-Thumb clamp 8-Beam 9-Depth measuring bar Internal measurement
