Please clean the measuring faces and beam with soft cloth, then close the external jaws, make sure that the zero lines o
Please clean the measuring faces and beam with soft cloth, then close the external jaws. If the needle does not point at
Parts Diagram… ... IMPORTANT. Servicing requires extreme care and
knowledge and should be performed only by a qualified ... Use only 3-wire
extension cords that have 3-prong grounding plugs, and 3-pole receptacles that
accept the tool's ...
iacare ol'tltc Erimï¬ IIIIICdUEIIII. ' Press and hold lrutltin D to show the alarm time arid release it to restore the
SUNDYNE. LMV-333 PUMPS. Instruction and Operation. Manual. August 2007.
Page 2. Copyright. All rights reserved. .... Pump Control During Start-Up ..
Rated insulation voltage of a circuit (Ui). 440 V. Rated impulse withstand voltage of the assembly (Uimp). Line/input 8
instruction system (VAMOIS) to assist technicians take ... should be paid attention by technicians. ... automotive interior, offering a new way to the concep-.
We are glad you have chosen to purchase a PANASONIC microwave oven.
Before ... oven for reheating and defrosting, with Panasonic's Inverter Technology
.
VR&AR Combined Manual Operation Instruction System on Industry. Products: A Case Study. Xuyue Yin, Yan Gu, Shiguang Qiu, Xiumin Fan. CIM Research ...
This manual provides instructions and procedures necessary to install, operate ...
seal between the electromagnetic and hydraulic sections of the valve.The two.
Feb 6, 1999 ... Fire Alarm Control Panel IQ8Control C/M. 2. FB 798950.10.GB0 / 08.09. Intended
purpose. This product must only be used for the applications ...
A. PURPOSE OF THE MANUAL. This manual is expressly intended to provide
sufficient information for qualified technicians experienced in diesel engines and
...
transpose operation using the 256-bit Intel advanced vector extension (AVX) instructions. We present a novel vector-based matrix transpose algorithm and its ...
3 Apr 2000 ... CB-60/CB-80 Cr. CB-60/CB-80 Cryobath Low Temperature emperature. Table of
Contents le of Contents. PREFACE. Compliance .
You can start to use PC-Dmis. Start new part program, only one program can be
online to use CMM ( others are off-line). Unit can be inch (for IE 415) or mm as.
500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000. 2705 ... MIL-
L1000-CG ... This manual is intended to reinforce and review safety techniques.
(03:00:14) - Free Download Linux Programmers Operation System Instruction Pdf. Free Ebooks Download. * Read or Download
Among forms of creative language, verbal humor has received some attention in the computational milieu. Some aspects of irony and wordplay could be ...
At any state ,press A key EL backlight for 3s . Alarm Setting. ⢠in normal display Mode, press B key once enter into A
most-educated generation in U.S. history. Yet despite their heavy investment in education, Millennials currently have th
This is an automatic mechanical watch with manual winding mechanism. • If the
watch .... phones, magnetic necklaces, etc., it may gain or lose time. • If the watch
...
Service Operation. A hi i ff ti d ffi i i th. Achieving effectiveness and efficiency in
the delivery and support of services so as to ensure value for the customer and ...
6-"MODE" button 7-"SET" button 8-Battery cover 9-Thumb roller (not for code with suffix "W") 10-Depth measuring bar
1. The caliper is dustproof and waterproof (IP67). The measuring methods are following: External measurement
Internal measurement
Step measurement
Depth measurement
fig.2
3. Button: When display is powered off: Press any button to turn on. When display is powered on: Long press "SET" to turn off. Press "MODE" once to enter setting zero mode, press "SET" to set zero. Press "MODE" twice to enter ABS(absolute measurement) and REL(relative measurement) conversion, press "SET" to change the mode, press "MODE" to exit. Press "MODE" three times to enter metric and inch conversion, press "SET" to change the unit, press "MODE" to exit. In ABS mode, press "SET" to hold the reading. In REL mode, press "SET" to set relative zero. 4. Please clean the measuring faces with soft cloth, then close the external jaws and set zero. Caliper should be checked regularly to make sure that it is properly initial reading set. 5. To get accurate measurement, it is necessary to control the force. During measurement, please always apply constant and proper force on the caliper. The measuring jaws should "hold" the workpiece and can still "slide" on the workpiece. 6. Automatic power off in about 4 hours in REL mode. Long press "SET" to turn off caliper in ABS mode. 7. If the product becomes abnormal, there is "ERRO" on display. Please press any button to return measuring mode, and set zero before use. 8. One battery can last for one year use. If there is "B" on display, battery voltage is too low, please replace battery. If caliper is not be used for a long time, please remove the battery. Otherwise, liquid may leak from the battery and damage the caliper. 9. Optional depth base attachment (code 6140).
2. Install battery: --- Loosen screw and remove the battery cover (fig.1) --- Put CR2032 battery into battery house, the positive side of battery (+) should face out (fig.2)
