2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 43553 (1008) ...
2011 CR-Z. AUG 2010 ... write down the radio station presets. 2. Disconnect the ...
INSTALLATION INSTRUCTIONS PARTS LIST Attachment Kit P/N 08V03-SZT-100
Accessory
Application
AUTOMATIC DAY/NIGHT MIRROR
2011 CR-Z
Publications No.
AII 43553 Issue Date
AUG 2010
Automatic Day/Night Mirror Kit P/N 08V03-TA0-100A Automatic day/night mirror
Automatic day/night mirror harness
EPT sealer
Spring
Operating Instructions Clip
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 5
Wire ties
Ratchet 8 mm and 10 mm Sockets Isopropyl alcohol Shop towel Diagonal cutters
Fuse label
Needle nose pliers 10 mm Open end wrench Rubber mallet
Harness cover
Trim Tool Set (T/N SOJATP2014) (Available through the Honda Tool and Equipment program. On the iN, click on: Service/Service Bay/Tool and Equipment Program, then enter the number under “Search.” Or call 888-424-6857.) Flat-tip screwdriver Masking tape
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43553 (1008)
08V03-SZT-1000-91
1 of 8
Illustration of the Automatic Day/Night Mirror Installed on the Vehicle
3.
AUTOMATIC DAY/NIGHT MIRROR
Using a plastic trim tool, remove the left and right lens from the map light console (four retaining tabs for each lens). VEHICLE CONNECTORS
MAP LIGHT CONSOLE
2 BOLTS AUTOMATIC DAY/NIGHT MIRROR HARNESS 2A FUSE
RIGHT MAP LIGHT LENS
LEFT MAP LIGHT LENS
4 RETAINING TABS
9N2701AX
4 RETAINING TABS
INSTALLATION
FRONT
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.
2.
Make sure you have the anti-theft codes for the audio unit and navigation system (if equipped), then write down the radio station presets.
PLASTIC TRIM TOOL
MAP LIGHT LENS
030101AX
4.
Remove the map light console (two bolts and unplug the vehicle connectors).
5.
Remove the rearview mirror from the mirror holder by rotating the stay 90° clockwise.
Disconnect the negative cable from the battery.
MIRROR HOLDER
Rotate 90° clockwise.
MIRROR HOLDER
REARVIEW MIRROR STAY
REARVIEW MIRROR 872105BY
2 of 8
AII 43553 (1008)
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
6.
Turn the left sunvisor toward the driver’s seat.
HOLDER
10. While holding down the sunvisor holder as shown, use a flat-tip screwdriver wrapped with masking tape to remove the left sunvisor holder (three retaining tabs).
Push and hold the retaining tab. FLAT-TIP SCREWDRIVER
MASKING TAPE
MASKING TAPE FRONT SLOT
RETAINING TABS
VEHICLE CONNECTOR If equipped.
Hold down.
SLOT
Rotate towards the driver’s seat.
FLAT-TIP SCREWDRIVER
LEFT SUNVISOR 030102BX
7.
8.
9.
LEFT SUNVISOR HOLDER
Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver wrapped with masking tape into the slot. Push and hold the retaining tab. While holding the retaining tab, push up on the left sunvisor, and rotate it towards the door to release the sunvisor, then remove the left sunvisor. NOTE: If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat steps 7 and 8.
033102AX
11. Pull away the door seal from around the driver’s A-pillar trim. VEHICLE PANEL
CLIP
Using a flat-tip screwdriver wrapped with masking tape, release the three retaining tabs on the left sunvisor holder.
Pull. Lightly tap.
MASKING TAPE RETAINING TABS
DRIVER’S A-PILLAR TRIM
CLIP SHOP TOWEL
SLOT
RUBBER MALLET
DOOR SEAL Pull away.
FLAT-TIP SCREWDRIVER
MARK
LEFT SUNVISOR HOLDER 033101AX
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
AREA MARKED “SIDE CURTAIN AIRBAG”
990413BX
12. Using a rubber mallet wrapped with a shop towel, lightly tap the area marked “SIDE CURTAIN AIRBAG” on the top of the driver’s A-pillar trim to push in the clip. Make sure to strike the area perpendicular to the vehicle.
AII 43553 (1008)
3 of 8
13. Remove the driver’s A-pillar trim (two clips).
15. Remove the driver’s under cover (turn the knob, two clips, and one pin).
2 CLIPS DRIVER’S A-PILLAR TRIM
PIN
2 CLIPS
KNOB Turn.
030103AX
DRIVER’S UNDER COVER
900504BB
14. Remove the fuse box cover (four retaining tabs). 16. Pull away the door seal from around the driver’s kick panel, and remove the driver’s kick panel (two clips and three retaining tabs). If the vehicle is equipped with foot well lights, unplug the vehicle connector.
DOOR SEAL Pull away.
VEHICLE CONNECTOR If equipped.
2 CLIPS FUSE BOX COVER
4 RETAINING TABS
900503AB
3 RETAINING TABS
DRIVER’S KICK PANEL 990203CX
4 of 8
AII 43553 (1008)
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
17. Using needle nose pliers, remove the vehicle spring, and install the new spring into the mirror holder. VEHICLE SPRING Discard.
MIRROR HOLDER
MIRROR HOLDER
19. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse case where the fuse label will attach. Attach the 2A fuse label to the fuse case on the automatic day/night mirror harness.
AUTOMATIC DAY/NIGHT MIRROR HARNESS
2A FUSE LABEL
NEW SPRING
NEEDLE NOSE PLIERS
MIRROR STAY Turn counterclockwise. MIRROR HOLDER FUSE CASE MIRROR STAY
AUTOMATIC DAY/NIGHT MIRROR
9N2702AX
20. At the fuse box, unplug the vehicle 8-pin connector. Plug the automatic day/night mirror harness 8-pin connector into the fuse box 8-pin connector. Plug the vehicle 8-pin connector into the automatic day/night mirror harness 8-pin connector as shown. 721413BE
VIEW FROM FRONT
18. Slide the automatic day/night mirror stay onto the mirror holder, and turn the mirror stay counterclockwise to secure the automatic day/night mirror.
FUSE BOX
VEHICLE 8-PIN CONNECTOR
VEHICLE 8-PIN CONNECTOR
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43553 (1008)
AUTOMATIC DAY/ NIGHT MIRROR HARNESS AUTOMATIC 9N2703AX 8-PIN DAY/NIGHT CONNECTOR MIRROR HARNESS 8-PIN CONNECTOR
5 of 8
21. Unplug the vehicle 12-pin connector from the fuse box, and plug the automatic day/night mirror harness 12-pin connector into the fuse box 12-pin connector. Plug the vehicle 12-pin connector into the automatic day/night mirror harness 12-pin connector as shown.
24. Pull away the door seal from around the dashboard. DASHBOARD
FRONT
VIEW FROM FRONT FUSE BOX
A-PILLAR
DOOR SEAL Pull away. AUTOMATIC DAY/NIGHT MIRROR HARNESS
990305CX
25. Insert the automatic day/night mirror harness between the dashboard and the A-pillar.
VEHICLE 12-PIN CONNECTOR VEHICLE 12-PIN CONNECTOR
AUTOMATIC AUTOMATIC DAY/NIGHT MIRROR DAY/NIGHT HARNESS MIRROR 12-PIN CONNECTOR HARNESS 12-PIN CONNECTOR
26. Align the green tape on the automatic day/night mirror harness with the vehicle clip, and secure the automatic day/night mirror harness to the vehicle harness with three wire ties.
9N2704AX
VEHICLE CLIP
GREEN TAPE
VEHICLE HARNESS AUTOMATIC DAY/NIGHT MIRROR HARNESS
22. Secure the automatic day/night mirror harness to the vehicle harness with one wire tie. AUTOMATIC DAY/NIGHT MIRROR HARNESS
WIRE TIE
990306BX
VEHICLE HARNESS WIRE TIE
WIRE TIE VEHICLE HARNESS
9N2705AX
23. Secure the vehicle harness to the vehicle harness with one wire tie. 6 of 8
AII 43553 (1008)
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
27. Route the automatic day/night mirror harness under the headliner as shown. Be careful not to crease the headliner. HEADLINER
29. Align the green tape on the automatic day/night mirror harness at the headliner. Route the automatic day/night mirror harness through the grooves on the harness cover. Secure the harness cover to the mirror stay. GREEN TAPE AUTOMATIC Align the HEADLINER DAY/NIGHT headliner. MIRROR HARNESS
HARNESS COVER
AUTOMATIC DAY/NIGHT MIRROR HARNESS
AUTOMATIC DAY/NIGHT MIRROR STAY
HARNESS COVER
AUTOMATIC DAY/NIGHT MIRROR HARNESS 9N3001AX
28. Plug the automatic day/night mirror harness 7-pin connector into the automatic day/night mirror.
AUTOMATIC DAY/ NIGHT MIRROR
721403AE
30. Slide the end of the harness cover under the headliner.
AUTOMATIC DAY/NIGHT MIRROR HARNESS 7-PIN CONNECTOR
31. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the EPT sealer will attach. Secure the automatic day/night mirror harness to the vehicle panel with one EPT sealer as shown. VEHICLE PANEL AUTOMATIC DAY/NIGHT MIRROR HARNESS EPT SEALER HEADLINER
AUTOMATIC DAY/NIGHT MIRROR 9N3002AX
EPT SEALER
9N3003AX
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
AII 43553 (1008)
7 of 8
32. Remove and discard the vehicle clip from the driver’s A-pillar trim, and install the new clip.
Function Check 1.
VEHICLE CLIP Discard. NEW CLIP Supplied.
Turn the ignition switch to ON (II), but do not start the engine. AUTOMATIC DAY/NIGHT MIRROR
DRIVER’S A-PILLAR TRIM
DRIVER’S A-PILLAR
SWITCH Turn on.
LED
AUTOMATIC DAY/NIGHT MIRROR
030406AB
2.
Turn the switch on. Check that the LED glows properly.
3.
Cover the front sensor on the automatic day/night mirror with your hand, and use a flash-light to light the rear sensor on the automatic day/night mirror. Check to make sure the mirror surface dims.
DRIVER’S A-PILLAR TRIM 981110AE
33. Reinstall the driver’s A-pillar trim. 34. Check that all wire harnesses are routed properly and all connectors are plugged in.
AUTOMATIC DAY/NIGHT MIRROR
35. Reinstall all removed parts. 36. Reconnect the negative cable to the battery. 37. Enter the customer’s audio and navigation system (if equipped) anti-theft codes, and reset the radio station presets.
MIRROR SURFACE
38. Reset the clock. 39. If the IMA battery level gauge display is at zero, start the engine, and hold it between 3,500 rpm and 4,000 rpm (without load) in P or N position until the IMA battery level gauge display shows at least half-charged. NOTE: •
•
Check the operation of the automatic day/night mirror according to the Operating Instructions supplied.
REAR SENSOR 030407AB
4.
Adjust the zone and calibrate as required.
40. Put the Operating Instructions in the glove box.
8 of 8
FRONT SENSOR Cover.
FLASH-LIGHT
AII 43553 (1008)
Step on the brake pedal, and move the shift lever to the “R” position. Repeat step 3, and check to make sure the mirror surface does not dim. •
Make sure that the parking brake is locked securely.
•
If the automatic day/night mirror does not function properly, check the fuse and all connectors, including the ground cable. © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
