machine with center distance of 3000, 4000, 6000, 8000 mm. • 8-position turret
SAUTER (VDI 50). • 8-position turret SAUTER with live rotational tools (VDI 50).
Meteor. CNC Lathe. User's Manual. Total Commitment to Education and Training
WorldWide. Denford Limited reserves the right to alter any specifications and ...
LARGE HORIZONTAL BORING MILL: SCHARMANN. • CAPABLE OF BORING
AND MILLING A VARIETY OF ... LARGE VERTICAL TURNING LATHE: GRAY.
H6C-T Main Features of CNC Lathe Controller. 1-1. 2. Operation .... Battery
Backup for CNC program storage in case of power-off. ..... N30 M3 S3000. N40
G1 ...
CNC lathe basics brought to perfeetion ... More Okuma high-speed, high-
accuracy mechatronics. NG turret (non-lift). Tow-along tailstock. (manual).
Precision ...
monitoring with wireless sensor network (WSN). ... monitoring is the tool to analyse routine of work and .... firmware it is possible to transmit live measurement.
May 3, 2013 ... CENTROID CNC control equipment and all connected machine tools. Keep this
manual in a safe ...... N015 G50 S3000. N020 G00 T0303.
fields such as the electronic, automotive and medical .... analyzed with image analysis techniques; machine ... Digital differential analyzer (DDA) integration.
CNC Turning and Milling Centres. Dugard 52 Twin Turret SY - Twin Spindle.
Dugard 52 Triple Turret SY - Twin Spindle. DUGARD. Machine Tools Since 1939.
In the present work, the statically data has been made and analysed to .... (feed force, thrust force and cutting force) and surface roughness in ... simulations of high-speed orthogonal machining were .... e used as a measurement tool, it this.
Jun 25, 2014 - 4 Boring mill jaws. 39.3â 4-Jaw manual chuck. TOOL HOLDER PACKAGE. Tool Type. Dimension. Quantity. OD t
this manual or its accompanying documents may be reproduced or ... Mirac PC
Series CNC Lathe User's Manual .... Section 3: CNC Machine Installation.
seeking experienced CNC Lathe or CNC Mill Setup and operators. The positions
require independence and accountability for quality and throughput of the CNC ...
Haas CNC Milling. Machine as a LatHe. AKA: “The Mill Lathe”. Problem: I first
came up with the idea to turn my milling machine into a lathe out of sheer ...
Lab-Volt CNC Lathe/Mill Version 5.3. Lab-Volt CNC Lathe/Mill Version 5.2.
Caution: Make sure that you download the firmware which corresponds to your ...
Collet Attachment. Without stopping the lathe spindle, the collet can be released,
bar stock fed through the spindle, and the collet tightened again. Equipment in-.
Adjusting the Metal Lathe Spindle. WARNING! Before adjusting the Metal. Lathe's
Spindle, make sure that power to the lathe and spindle are turned OFF.
Indexable Carbide Available from Logan Actuator Co. - (888) 95-LATHE - [email protected]
correct an inaccurate lathe, but only to show how it ... quickest way to test a lathe
for truth would be to ..... hand end of the lathe spindle being used, one to carry a ...
Given the proper care. a good lathe will retain its accuracy. Fig. I. indefinitely. ...
To transmit power from the motor to the lathe spindle etti- cienlly, all belts must be
...
Contact your Mastercam Dealer ... Navigate Through Mastercam . ..... [Select
another entity]: SelectEntity D. Select Entity C here. Select Entity D here. Page 5 9
...
o Mazatrol T32-2 Programming Manual. Program CNC Lathe ogram CNC Lathe.
1. Power up the CNC lathe. o Turn ON the main power switch, below the control ...
Toolmaker Training
Duty B: Lathes (CNC) Page 1 of 10
B-01: Pr ogram CNC Lathe Program SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task. EQUIPMENT o Mazak QuickTurn 28N RESOURCES o Mazatrol T32-2 Operating Manual o Mazatrol T32-2 Programming Manual Pr ogram CNC Lathe Program 1.
Power up the CNC lathe. o Turn ON the main power switch, below the control panel. o Press the power button to turn ON the control panel power.
2.
Set the machine zer o. zero. o Press the key.
Issued 06/98
Toolmaker Training
Duty B: Lathes (CNC) Page 2 of 10
o Home the X axis first to avoid damaging the machine. o Press the manual control (Ý) positive X axis feed until the X axis home value reads zero on the control panel. o Press the manual control (Þ ) positive Z axis feed until the Z axis home value reads zero on the control panel. 3.
Pr ess the left gr een softkey to view the menu options. Press green
4.
Select an unused pr ogram number to start a new CNC pr ogram. program program. o Press the softkey to view the existing program numbers (Wno.).
Enter General Piece Parameters
Issued 06/98
1.
Pr ess the left gr een softkey to begin entering the first pr ocess Press green process parameters.
2.
Pr ess the softkey to begin pr ogramming. Press programming.
