S Series. Confidential. Chapter 1. Disassembly & Assembly Guide. 1.MS-1-D.1. 1
-3. Disassembly & Assembly. - Main Section -. MS-1 Main Section Disassembly ...
1.MS-1-D.1
Confidential
Chapter 1. Disassembly & Assembly Guide 1-3. Disassembly & Assembly
- Main Section MS-1 Main Section Disassembly
S Series
Confidential
1.MS-1-D.2
Battery Pack 2)
1)
Battery Pack
Slide the Battery Lock (L) to the UNLOCK side.
With the Battery Lock (R) moved on the UNLOCK side, remove the Battery Pack.
S Series
Confidential
1.MS-1-D.3
Cover (Memory) 1)
Screw: S240P - B11(Special Screw) Other - B9
2) 1 [MA]
Remove the two screws. *The type of screw differs by model.
Slide the Cover (Memory) toward the front to remove. *The two detents on the upper side are engaged with the Housing (Bottom).
Memory
A
Wireless LAN Card
The Memory and the Wireless LAN Card are located under the Cover in section A. S Series
Confidential
1.MS-1-D.4
Keyboard 1)
2)
Screw:B1
Detent
FPC
Disengage the two detents with a bamboo spatula, and turn the Keyboard toward the front. *The FPC is connected on the back. *Push the detents toward the rear to disengage.
Remove the nine screws from the back.
3)
FPC
Connector
Disconnect the FPC. *Raise the Connector to unlock. S Series
Confidential
1.MS-1-D.5
Palmrest 1)
2)
Screw: B1
FFC Harness
Remove the five screws.
3)
Disconnect the Harness (two places) and the FFC (two places). *Pull off the Harness and the FFC upward.
Remark
4
Palmrest
2
3
1
Disengaging the five detents, remove the Palmrest. *The detents are engaged toward the outside.
Raising the Palmrest while sliding it a little in the arrow direction in the order of 1, 2, 3, 4, disengage the detents. S Series
Confidential
1.MS-1-D.6
HDD 1)
2)
Screw: B4
Connector
Bracket (HDD)
Remove the two screws.
HDD
Disconnect the Connector, and remove the HDD. *The HDD is removed together with the Bracket (HDD).
S Series
Confidential
1.MS-1-D.7
Parts of the HDD 2)
1)
FPC
Screw: B8
Bracket
Remove the four screws, and then the Bracket (HDD).
Remove the FPC.
Remark
Disconnect the Connector portion little by little with a tweezers. *Be careful not to bend the pins. S Series
Confidential
1.MS-1-D.8
Heatsink 1)
Screw: Red-B5 / Blue-B4
Remark
Heatsink
Remove the three screws, and then the Heatsink.
The Spring is attached under the Screw.
S Series
Confidential
1.MS-1-D.9
PC Card Connector 1)
2)
Screw: B4
PC Card Connector Connector
Bracket
Remove the one screw.
Disconnect the Connector, and remove the PC Card Connector. *The Bracket is removed together. *The PC Card Connector is located under the Bracket.
3) Screw: B10
Bracket
Remove the four screws, and then the Bracket. S Series
Confidential
1.MS-1-D.10
Optical Disc Drive 1)
2)
Screw: B4
Connector
Remove the four screws.
Disconnect the FFC. *Raise the Connector and release the lock.
3)
Optical Disc Drive
Remove the Optical Disc Drive. S Series
Confidential
1.MS-1-D.11
IFX-311 Board, IFX-331 Board 2)
1)
FFC
Screw: B4
Lock Lever
IFX-311 Board Slide the both ends of the lock lever in the arrow direction to unlock, and disconnect the FFC.
3)
Remove the three screws, and then the IFX-311 Board.
4)
Bluetooth Model Screw: B4
Harness (RJ-45/11)
IFX-331 Board
Remove the one screw, and then the IFX-331 Board.
Remove the Harness (RJ-45/11). S Series
Confidential
1.MS-1-D.12
Parts of the IFX Board
Common 2)
1) Screw: B3
Modem Card
Connector
Remove the two screws.
3)
Remove the Modem Card. *The Connector is located on the back.
4) Harness (RJ-45/11)
IFX-311 Board
Turn over the IFX-311 Board, and peel off the Sheet.
Connector
Disconnect the Connector in the arrow direction, and remove the Harness (RJ-45/11). S Series
Confidential
1.MS-1-D.13
Parts of the IFX Board
Bluetooth Model
1) Bluetooth Module
Notch Connector
Remove the Bluetooth Module. *The Connector is located on the back. *The Coaxial Cable is hooked on the notch.
2)
IFX-331 Board
Bluetooth Module
Disconnect the Coaxial Cable from the IFX-331 Board and the Bluetooth Module respectively. *Disconnect the Connector vertically.
S Series
Confidential
1.MS-1-D.14
CNX-261 Board 1)
Screw: B4
2) Connector
CNX Board
Escutcheon (L )
Remove the two screws.
Remove the CNX Board. *The Connector is fitted in the Escutcheon (L).
3)
FFC
Disconnect the FFC. *Pull it off in the arrow direction. S Series
Confidential
1.MS-1-D.15
Mother Board -1 1)
1)
6 [DEL]
Screw: B4
Cover
Remove the Cover.
Remove the one screw.
2)
3) Screw: B4 Harness (LCD) Bracket
Disconnect the Harness (LCD). *Pull it off upward.
Remove the one screw, and then the Bracket. S Series
Confidential
1.MS-1-D.16
Mother Board -2 5)
4)
Screw: B4
Screw: B4
Spacer (MBX)
DC Jack
Remove the four screws and the Spacer (MBX) (one location). *Remove the Spacer (MBX) using the 4 mm socket wrench.
Remove the one screw, and then the DC Jack.
6)
7) Escutcheon (R)
Mother Board
1 Wireless LAN Card
Tab
2
1 Remove the Mother Board. *The Connector is fitted in the Escutcheon (R).
Turn over the Mother Board, open the tabs outward (arrow 1), and pull off the Wireless LAN Card diagonally upward (arrow 2). S Series
Confidential
1.MS-1-D.17
LCD Section 1)
Screw: B4
LCD Section
Remove the four screws, and then the LCD Section upward.
S Series
Confidential
1.MS-1-D.18
Parts of the Housing (Bottom) 2)
1)
Escutcheon (L)
Escutcheon (R)
Remove the one Escutcheon (R).
3)
Screw: B4
Remove the one Escutcheon (L).
4)
6 [DEL]
Cover
6 [DEL]
Cover
Remove the one screw.and then the Cover.
Remove the one Cover. S Series
Confidential
1.MS-1-D.19
Parts of the Escutcheon (L/R) 2)
1) Escutcheon (L)
Cover
Kenjington
Remove the Kenjington from the Escutcheon (L).
Remove the Cover from the Escutcheon (L).
3)
Cover
Escutcheon (R) Remove the Cover from the Escutcheon (R). S Series
Confidential
Update History
[ADD]---Addition [DEL]---Deletion [CHG]---Change [COR]---Correction [MA]---Model Addition
Date 2004.09.17
1
[MA] (Page 3)
Contents
2005.01.06
6
[DEL] Parts (Page 15,18)
Version No. 2.00 3.00
S Series
